1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * OMAP3/4 - specific DPLL control functions 4 * 5 * Copyright (C) 2009-2010 Texas Instruments, Inc. 6 * Copyright (C) 2009-2010 Nokia Corporation 7 * 8 * Written by Paul Walmsley 9 * Testing and integration fixes by Jouni Högander 10 * 11 * 36xx support added by Vishwanath BS, Richard Woodruff, and Nishanth 12 * Menon 13 * 14 * Parts of this code are based on code written by 15 * Richard Woodruff, Tony Lindgren, Tuukka Tikkanen, Karthik Dasu 16 */ 17 18 #include <linux/kernel.h> 19 #include <linux/device.h> 20 #include <linux/list.h> 21 #include <linux/errno.h> 22 #include <linux/delay.h> 23 #include <linux/clk.h> 24 #include <linux/io.h> 25 #include <linux/bitops.h> 26 #include <linux/clkdev.h> 27 #include <linux/clk/ti.h> 28 29 #include "clock.h" 30 31 /* CM_AUTOIDLE_PLL*.AUTO_* bit values */ 32 #define DPLL_AUTOIDLE_DISABLE 0x0 33 #define DPLL_AUTOIDLE_LOW_POWER_STOP 0x1 34 35 #define MAX_DPLL_WAIT_TRIES 1000000 36 37 #define OMAP3XXX_EN_DPLL_LOCKED 0x7 38 39 /* Forward declarations */ 40 static u32 omap3_dpll_autoidle_read(struct clk_hw_omap *clk); 41 static void omap3_dpll_deny_idle(struct clk_hw_omap *clk); 42 static void omap3_dpll_allow_idle(struct clk_hw_omap *clk); 43 44 /* Private functions */ 45 46 /* _omap3_dpll_write_clken - write clken_bits arg to a DPLL's enable bits */ 47 static void _omap3_dpll_write_clken(struct clk_hw_omap *clk, u8 clken_bits) 48 { 49 const struct dpll_data *dd; 50 u32 v; 51 52 dd = clk->dpll_data; 53 54 v = ti_clk_ll_ops->clk_readl(&dd->control_reg); 55 v &= ~dd->enable_mask; 56 v |= clken_bits << __ffs(dd->enable_mask); 57 ti_clk_ll_ops->clk_writel(v, &dd->control_reg); 58 } 59 60 /* _omap3_wait_dpll_status: wait for a DPLL to enter a specific state */ 61 static int _omap3_wait_dpll_status(struct clk_hw_omap *clk, u8 state) 62 { 63 const struct dpll_data *dd; 64 int i = 0; 65 int ret = -EINVAL; 66 const char *clk_name; 67 68 dd = clk->dpll_data; 69 clk_name = clk_hw_get_name(&clk->hw); 70 71 state <<= __ffs(dd->idlest_mask); 72 73 while (((ti_clk_ll_ops->clk_readl(&dd->idlest_reg) & dd->idlest_mask) 74 != state) && i < MAX_DPLL_WAIT_TRIES) { 75 i++; 76 udelay(1); 77 } 78 79 if (i == MAX_DPLL_WAIT_TRIES) { 80 pr_err("clock: %s failed transition to '%s'\n", 81 clk_name, (state) ? "locked" : "bypassed"); 82 } else { 83 pr_debug("clock: %s transition to '%s' in %d loops\n", 84 clk_name, (state) ? "locked" : "bypassed", i); 85 86 ret = 0; 87 } 88 89 return ret; 90 } 91 92 /* From 3430 TRM ES2 4.7.6.2 */ 93 static u16 _omap3_dpll_compute_freqsel(struct clk_hw_omap *clk, u8 n) 94 { 95 unsigned long fint; 96 u16 f = 0; 97 98 fint = clk_hw_get_rate(clk->dpll_data->clk_ref) / n; 99 100 pr_debug("clock: fint is %lu\n", fint); 101 102 if (fint >= 750000 && fint <= 1000000) 103 f = 0x3; 104 else if (fint > 1000000 && fint <= 1250000) 105 f = 0x4; 106 else if (fint > 1250000 && fint <= 1500000) 107 f = 0x5; 108 else if (fint > 1500000 && fint <= 1750000) 109 f = 0x6; 110 else if (fint > 1750000 && fint <= 2100000) 111 f = 0x7; 112 else if (fint > 7500000 && fint <= 10000000) 113 f = 0xB; 114 else if (fint > 10000000 && fint <= 12500000) 115 f = 0xC; 116 else if (fint > 12500000 && fint <= 15000000) 117 f = 0xD; 118 else if (fint > 15000000 && fint <= 17500000) 119 f = 0xE; 120 else if (fint > 17500000 && fint <= 21000000) 121 f = 0xF; 122 else 123 pr_debug("clock: unknown freqsel setting for %d\n", n); 124 125 return f; 126 } 127 128 /** 129 * _omap3_noncore_dpll_lock - instruct a DPLL to lock and wait for readiness 130 * @clk: pointer to a DPLL struct clk 131 * 132 * Instructs a non-CORE DPLL to lock. Waits for the DPLL to report 133 * readiness before returning. Will save and restore the DPLL's 134 * autoidle state across the enable, per the CDP code. If the DPLL 135 * locked successfully, return 0; if the DPLL did not lock in the time 136 * allotted, or DPLL3 was passed in, return -EINVAL. 137 */ 138 static int _omap3_noncore_dpll_lock(struct clk_hw_omap *clk) 139 { 140 const struct dpll_data *dd; 141 u8 ai; 142 u8 state = 1; 143 int r = 0; 144 145 pr_debug("clock: locking DPLL %s\n", clk_hw_get_name(&clk->hw)); 146 147 dd = clk->dpll_data; 148 state <<= __ffs(dd->idlest_mask); 149 150 /* Check if already locked */ 151 if ((ti_clk_ll_ops->clk_readl(&dd->idlest_reg) & dd->idlest_mask) == 152 state) 153 goto done; 154 155 ai = omap3_dpll_autoidle_read(clk); 156 157 if (ai) 158 omap3_dpll_deny_idle(clk); 159 160 _omap3_dpll_write_clken(clk, DPLL_LOCKED); 161 162 r = _omap3_wait_dpll_status(clk, 1); 163 164 if (ai) 165 omap3_dpll_allow_idle(clk); 166 167 done: 168 return r; 169 } 170 171 /** 172 * _omap3_noncore_dpll_bypass - instruct a DPLL to bypass and wait for readiness 173 * @clk: pointer to a DPLL struct clk 174 * 175 * Instructs a non-CORE DPLL to enter low-power bypass mode. In 176 * bypass mode, the DPLL's rate is set equal to its parent clock's 177 * rate. Waits for the DPLL to report readiness before returning. 178 * Will save and restore the DPLL's autoidle state across the enable, 179 * per the CDP code. If the DPLL entered bypass mode successfully, 180 * return 0; if the DPLL did not enter bypass in the time allotted, or 181 * DPLL3 was passed in, or the DPLL does not support low-power bypass, 182 * return -EINVAL. 183 */ 184 static int _omap3_noncore_dpll_bypass(struct clk_hw_omap *clk) 185 { 186 int r; 187 u8 ai; 188 189 if (!(clk->dpll_data->modes & (1 << DPLL_LOW_POWER_BYPASS))) 190 return -EINVAL; 191 192 pr_debug("clock: configuring DPLL %s for low-power bypass\n", 193 clk_hw_get_name(&clk->hw)); 194 195 ai = omap3_dpll_autoidle_read(clk); 196 197 _omap3_dpll_write_clken(clk, DPLL_LOW_POWER_BYPASS); 198 199 r = _omap3_wait_dpll_status(clk, 0); 200 201 if (ai) 202 omap3_dpll_allow_idle(clk); 203 204 return r; 205 } 206 207 /** 208 * _omap3_noncore_dpll_stop - instruct a DPLL to stop 209 * @clk: pointer to a DPLL struct clk 210 * 211 * Instructs a non-CORE DPLL to enter low-power stop. Will save and 212 * restore the DPLL's autoidle state across the stop, per the CDP 213 * code. If DPLL3 was passed in, or the DPLL does not support 214 * low-power stop, return -EINVAL; otherwise, return 0. 215 */ 216 static int _omap3_noncore_dpll_stop(struct clk_hw_omap *clk) 217 { 218 u8 ai; 219 220 if (!(clk->dpll_data->modes & (1 << DPLL_LOW_POWER_STOP))) 221 return -EINVAL; 222 223 pr_debug("clock: stopping DPLL %s\n", clk_hw_get_name(&clk->hw)); 224 225 ai = omap3_dpll_autoidle_read(clk); 226 227 _omap3_dpll_write_clken(clk, DPLL_LOW_POWER_STOP); 228 229 if (ai) 230 omap3_dpll_allow_idle(clk); 231 232 return 0; 233 } 234 235 /** 236 * _lookup_dco - Lookup DCO used by j-type DPLL 237 * @clk: pointer to a DPLL struct clk 238 * @dco: digital control oscillator selector 239 * @m: DPLL multiplier to set 240 * @n: DPLL divider to set 241 * 242 * See 36xx TRM section 3.5.3.3.3.2 "Type B DPLL (Low-Jitter)" 243 * 244 * XXX This code is not needed for 3430/AM35xx; can it be optimized 245 * out in non-multi-OMAP builds for those chips? 246 */ 247 static void _lookup_dco(struct clk_hw_omap *clk, u8 *dco, u16 m, u8 n) 248 { 249 unsigned long fint, clkinp; /* watch out for overflow */ 250 251 clkinp = clk_hw_get_rate(clk_hw_get_parent(&clk->hw)); 252 fint = (clkinp / n) * m; 253 254 if (fint < 1000000000) 255 *dco = 2; 256 else 257 *dco = 4; 258 } 259 260 /** 261 * _lookup_sddiv - Calculate sigma delta divider for j-type DPLL 262 * @clk: pointer to a DPLL struct clk 263 * @sd_div: target sigma-delta divider 264 * @m: DPLL multiplier to set 265 * @n: DPLL divider to set 266 * 267 * See 36xx TRM section 3.5.3.3.3.2 "Type B DPLL (Low-Jitter)" 268 * 269 * XXX This code is not needed for 3430/AM35xx; can it be optimized 270 * out in non-multi-OMAP builds for those chips? 271 */ 272 static void _lookup_sddiv(struct clk_hw_omap *clk, u8 *sd_div, u16 m, u8 n) 273 { 274 unsigned long clkinp, sd; /* watch out for overflow */ 275 int mod1, mod2; 276 277 clkinp = clk_hw_get_rate(clk_hw_get_parent(&clk->hw)); 278 279 /* 280 * target sigma-delta to near 250MHz 281 * sd = ceil[(m/(n+1)) * (clkinp_MHz / 250)] 282 */ 283 clkinp /= 100000; /* shift from MHz to 10*Hz for 38.4 and 19.2 */ 284 mod1 = (clkinp * m) % (250 * n); 285 sd = (clkinp * m) / (250 * n); 286 mod2 = sd % 10; 287 sd /= 10; 288 289 if (mod1 || mod2) 290 sd++; 291 *sd_div = sd; 292 } 293 294 /** 295 * omap3_noncore_dpll_ssc_program - set spread-spectrum clocking registers 296 * @clk: struct clk * of DPLL to set 297 * 298 * Enable the DPLL spread spectrum clocking if frequency modulation and 299 * frequency spreading have been set, otherwise disable it. 300 */ 301 static void omap3_noncore_dpll_ssc_program(struct clk_hw_omap *clk) 302 { 303 struct dpll_data *dd = clk->dpll_data; 304 unsigned long ref_rate; 305 u32 v, ctrl, mod_freq_divider, exponent, mantissa; 306 u32 deltam_step, deltam_ceil; 307 308 ctrl = ti_clk_ll_ops->clk_readl(&dd->control_reg); 309 310 if (dd->ssc_modfreq && dd->ssc_deltam) { 311 ctrl |= dd->ssc_enable_mask; 312 313 if (dd->ssc_downspread) 314 ctrl |= dd->ssc_downspread_mask; 315 else 316 ctrl &= ~dd->ssc_downspread_mask; 317 318 ref_rate = clk_hw_get_rate(dd->clk_ref); 319 mod_freq_divider = 320 (ref_rate / dd->last_rounded_n) / (4 * dd->ssc_modfreq); 321 if (dd->ssc_modfreq > (ref_rate / 70)) 322 pr_warn("clock: SSC modulation frequency of DPLL %s greater than %ld\n", 323 __clk_get_name(clk->hw.clk), ref_rate / 70); 324 325 exponent = 0; 326 mantissa = mod_freq_divider; 327 while ((mantissa > 127) && (exponent < 7)) { 328 exponent++; 329 mantissa /= 2; 330 } 331 if (mantissa > 127) 332 mantissa = 127; 333 334 v = ti_clk_ll_ops->clk_readl(&dd->ssc_modfreq_reg); 335 v &= ~(dd->ssc_modfreq_mant_mask | dd->ssc_modfreq_exp_mask); 336 v |= mantissa << __ffs(dd->ssc_modfreq_mant_mask); 337 v |= exponent << __ffs(dd->ssc_modfreq_exp_mask); 338 ti_clk_ll_ops->clk_writel(v, &dd->ssc_modfreq_reg); 339 340 deltam_step = dd->last_rounded_m * dd->ssc_deltam; 341 deltam_step /= 10; 342 if (dd->ssc_downspread) 343 deltam_step /= 2; 344 345 deltam_step <<= __ffs(dd->ssc_deltam_int_mask); 346 deltam_step /= 100; 347 deltam_step /= mod_freq_divider; 348 if (deltam_step > 0xFFFFF) 349 deltam_step = 0xFFFFF; 350 351 deltam_ceil = (deltam_step & dd->ssc_deltam_int_mask) >> 352 __ffs(dd->ssc_deltam_int_mask); 353 if (deltam_step & dd->ssc_deltam_frac_mask) 354 deltam_ceil++; 355 356 if ((dd->ssc_downspread && 357 ((dd->last_rounded_m - (2 * deltam_ceil)) < 20 || 358 dd->last_rounded_m > 2045)) || 359 ((dd->last_rounded_m - deltam_ceil) < 20 || 360 (dd->last_rounded_m + deltam_ceil) > 2045)) 361 pr_warn("clock: SSC multiplier of DPLL %s is out of range\n", 362 __clk_get_name(clk->hw.clk)); 363 364 v = ti_clk_ll_ops->clk_readl(&dd->ssc_deltam_reg); 365 v &= ~(dd->ssc_deltam_int_mask | dd->ssc_deltam_frac_mask); 366 v |= deltam_step << __ffs(dd->ssc_deltam_int_mask | 367 dd->ssc_deltam_frac_mask); 368 ti_clk_ll_ops->clk_writel(v, &dd->ssc_deltam_reg); 369 } else { 370 ctrl &= ~dd->ssc_enable_mask; 371 } 372 373 ti_clk_ll_ops->clk_writel(ctrl, &dd->control_reg); 374 } 375 376 /** 377 * omap3_noncore_dpll_program - set non-core DPLL M,N values directly 378 * @clk: struct clk * of DPLL to set 379 * @freqsel: FREQSEL value to set 380 * 381 * Program the DPLL with the last M, N values calculated, and wait for 382 * the DPLL to lock. Returns -EINVAL upon error, or 0 upon success. 383 */ 384 static int omap3_noncore_dpll_program(struct clk_hw_omap *clk, u16 freqsel) 385 { 386 struct dpll_data *dd = clk->dpll_data; 387 u8 dco, sd_div, ai = 0; 388 u32 v; 389 bool errata_i810; 390 391 /* 3430 ES2 TRM: 4.7.6.9 DPLL Programming Sequence */ 392 _omap3_noncore_dpll_bypass(clk); 393 394 /* 395 * Set jitter correction. Jitter correction applicable for OMAP343X 396 * only since freqsel field is no longer present on other devices. 397 */ 398 if (ti_clk_get_features()->flags & TI_CLK_DPLL_HAS_FREQSEL) { 399 v = ti_clk_ll_ops->clk_readl(&dd->control_reg); 400 v &= ~dd->freqsel_mask; 401 v |= freqsel << __ffs(dd->freqsel_mask); 402 ti_clk_ll_ops->clk_writel(v, &dd->control_reg); 403 } 404 405 /* Set DPLL multiplier, divider */ 406 v = ti_clk_ll_ops->clk_readl(&dd->mult_div1_reg); 407 408 /* Handle Duty Cycle Correction */ 409 if (dd->dcc_mask) { 410 if (dd->last_rounded_rate >= dd->dcc_rate) 411 v |= dd->dcc_mask; /* Enable DCC */ 412 else 413 v &= ~dd->dcc_mask; /* Disable DCC */ 414 } 415 416 v &= ~(dd->mult_mask | dd->div1_mask); 417 v |= dd->last_rounded_m << __ffs(dd->mult_mask); 418 v |= (dd->last_rounded_n - 1) << __ffs(dd->div1_mask); 419 420 /* Configure dco and sd_div for dplls that have these fields */ 421 if (dd->dco_mask) { 422 _lookup_dco(clk, &dco, dd->last_rounded_m, dd->last_rounded_n); 423 v &= ~(dd->dco_mask); 424 v |= dco << __ffs(dd->dco_mask); 425 } 426 if (dd->sddiv_mask) { 427 _lookup_sddiv(clk, &sd_div, dd->last_rounded_m, 428 dd->last_rounded_n); 429 v &= ~(dd->sddiv_mask); 430 v |= sd_div << __ffs(dd->sddiv_mask); 431 } 432 433 /* 434 * Errata i810 - DPLL controller can get stuck while transitioning 435 * to a power saving state. Software must ensure the DPLL can not 436 * transition to a low power state while changing M/N values. 437 * Easiest way to accomplish this is to prevent DPLL autoidle 438 * before doing the M/N re-program. 439 */ 440 errata_i810 = ti_clk_get_features()->flags & TI_CLK_ERRATA_I810; 441 442 if (errata_i810) { 443 ai = omap3_dpll_autoidle_read(clk); 444 if (ai) { 445 omap3_dpll_deny_idle(clk); 446 447 /* OCP barrier */ 448 omap3_dpll_autoidle_read(clk); 449 } 450 } 451 452 ti_clk_ll_ops->clk_writel(v, &dd->mult_div1_reg); 453 454 /* Set 4X multiplier and low-power mode */ 455 if (dd->m4xen_mask || dd->lpmode_mask) { 456 v = ti_clk_ll_ops->clk_readl(&dd->control_reg); 457 458 if (dd->m4xen_mask) { 459 if (dd->last_rounded_m4xen) 460 v |= dd->m4xen_mask; 461 else 462 v &= ~dd->m4xen_mask; 463 } 464 465 if (dd->lpmode_mask) { 466 if (dd->last_rounded_lpmode) 467 v |= dd->lpmode_mask; 468 else 469 v &= ~dd->lpmode_mask; 470 } 471 472 ti_clk_ll_ops->clk_writel(v, &dd->control_reg); 473 } 474 475 if (dd->ssc_enable_mask) 476 omap3_noncore_dpll_ssc_program(clk); 477 478 /* We let the clock framework set the other output dividers later */ 479 480 /* REVISIT: Set ramp-up delay? */ 481 482 _omap3_noncore_dpll_lock(clk); 483 484 if (errata_i810 && ai) 485 omap3_dpll_allow_idle(clk); 486 487 return 0; 488 } 489 490 /* Public functions */ 491 492 /** 493 * omap3_dpll_recalc - recalculate DPLL rate 494 * @hw: struct clk_hw containing the DPLL struct clk 495 * @parent_rate: clock rate of the DPLL parent 496 * 497 * Recalculate and propagate the DPLL rate. 498 */ 499 unsigned long omap3_dpll_recalc(struct clk_hw *hw, unsigned long parent_rate) 500 { 501 struct clk_hw_omap *clk = to_clk_hw_omap(hw); 502 503 return omap2_get_dpll_rate(clk); 504 } 505 506 /* Non-CORE DPLL (e.g., DPLLs that do not control SDRC) clock functions */ 507 508 /** 509 * omap3_noncore_dpll_enable - instruct a DPLL to enter bypass or lock mode 510 * @hw: struct clk_hw containing then pointer to a DPLL struct clk 511 * 512 * Instructs a non-CORE DPLL to enable, e.g., to enter bypass or lock. 513 * The choice of modes depends on the DPLL's programmed rate: if it is 514 * the same as the DPLL's parent clock, it will enter bypass; 515 * otherwise, it will enter lock. This code will wait for the DPLL to 516 * indicate readiness before returning, unless the DPLL takes too long 517 * to enter the target state. Intended to be used as the struct clk's 518 * enable function. If DPLL3 was passed in, or the DPLL does not 519 * support low-power stop, or if the DPLL took too long to enter 520 * bypass or lock, return -EINVAL; otherwise, return 0. 521 */ 522 int omap3_noncore_dpll_enable(struct clk_hw *hw) 523 { 524 struct clk_hw_omap *clk = to_clk_hw_omap(hw); 525 int r; 526 struct dpll_data *dd; 527 struct clk_hw *parent; 528 529 dd = clk->dpll_data; 530 if (!dd) 531 return -EINVAL; 532 533 if (clk->clkdm) { 534 r = ti_clk_ll_ops->clkdm_clk_enable(clk->clkdm, hw->clk); 535 if (r) { 536 WARN(1, 537 "%s: could not enable %s's clockdomain %s: %d\n", 538 __func__, clk_hw_get_name(hw), 539 clk->clkdm_name, r); 540 return r; 541 } 542 } 543 544 parent = clk_hw_get_parent(hw); 545 546 if (clk_hw_get_rate(hw) == clk_hw_get_rate(dd->clk_bypass)) { 547 WARN_ON(parent != dd->clk_bypass); 548 r = _omap3_noncore_dpll_bypass(clk); 549 } else { 550 WARN_ON(parent != dd->clk_ref); 551 r = _omap3_noncore_dpll_lock(clk); 552 } 553 554 return r; 555 } 556 557 /** 558 * omap3_noncore_dpll_disable - instruct a DPLL to enter low-power stop 559 * @hw: struct clk_hw containing then pointer to a DPLL struct clk 560 * 561 * Instructs a non-CORE DPLL to enter low-power stop. This function is 562 * intended for use in struct clkops. No return value. 563 */ 564 void omap3_noncore_dpll_disable(struct clk_hw *hw) 565 { 566 struct clk_hw_omap *clk = to_clk_hw_omap(hw); 567 568 _omap3_noncore_dpll_stop(clk); 569 if (clk->clkdm) 570 ti_clk_ll_ops->clkdm_clk_disable(clk->clkdm, hw->clk); 571 } 572 573 /* Non-CORE DPLL rate set code */ 574 575 /** 576 * omap3_noncore_dpll_determine_rate - determine rate for a DPLL 577 * @hw: pointer to the clock to determine rate for 578 * @req: target rate request 579 * 580 * Determines which DPLL mode to use for reaching a desired target rate. 581 * Checks whether the DPLL shall be in bypass or locked mode, and if 582 * locked, calculates the M,N values for the DPLL via round-rate. 583 * Returns a 0 on success, negative error value in failure. 584 */ 585 int omap3_noncore_dpll_determine_rate(struct clk_hw *hw, 586 struct clk_rate_request *req) 587 { 588 struct clk_hw_omap *clk = to_clk_hw_omap(hw); 589 struct dpll_data *dd; 590 591 if (!req->rate) 592 return -EINVAL; 593 594 dd = clk->dpll_data; 595 if (!dd) 596 return -EINVAL; 597 598 if (clk_hw_get_rate(dd->clk_bypass) == req->rate && 599 (dd->modes & (1 << DPLL_LOW_POWER_BYPASS))) { 600 req->best_parent_hw = dd->clk_bypass; 601 } else { 602 req->rate = omap2_dpll_round_rate(hw, req->rate, 603 &req->best_parent_rate); 604 req->best_parent_hw = dd->clk_ref; 605 } 606 607 req->best_parent_rate = req->rate; 608 609 return 0; 610 } 611 612 /** 613 * omap3_noncore_dpll_set_parent - set parent for a DPLL clock 614 * @hw: pointer to the clock to set parent for 615 * @index: parent index to select 616 * 617 * Sets parent for a DPLL clock. This sets the DPLL into bypass or 618 * locked mode. Returns 0 with success, negative error value otherwise. 619 */ 620 int omap3_noncore_dpll_set_parent(struct clk_hw *hw, u8 index) 621 { 622 struct clk_hw_omap *clk = to_clk_hw_omap(hw); 623 int ret; 624 625 if (!hw) 626 return -EINVAL; 627 628 if (index) 629 ret = _omap3_noncore_dpll_bypass(clk); 630 else 631 ret = _omap3_noncore_dpll_lock(clk); 632 633 return ret; 634 } 635 636 /** 637 * omap3_noncore_dpll_set_rate - set rate for a DPLL clock 638 * @hw: pointer to the clock to set parent for 639 * @rate: target rate for the clock 640 * @parent_rate: rate of the parent clock 641 * 642 * Sets rate for a DPLL clock. First checks if the clock parent is 643 * reference clock (in bypass mode, the rate of the clock can't be 644 * changed) and proceeds with the rate change operation. Returns 0 645 * with success, negative error value otherwise. 646 */ 647 int omap3_noncore_dpll_set_rate(struct clk_hw *hw, unsigned long rate, 648 unsigned long parent_rate) 649 { 650 struct clk_hw_omap *clk = to_clk_hw_omap(hw); 651 struct dpll_data *dd; 652 u16 freqsel = 0; 653 int ret; 654 655 if (!hw || !rate) 656 return -EINVAL; 657 658 dd = clk->dpll_data; 659 if (!dd) 660 return -EINVAL; 661 662 if (clk_hw_get_parent(hw) != dd->clk_ref) 663 return -EINVAL; 664 665 if (dd->last_rounded_rate == 0) 666 return -EINVAL; 667 668 /* Freqsel is available only on OMAP343X devices */ 669 if (ti_clk_get_features()->flags & TI_CLK_DPLL_HAS_FREQSEL) { 670 freqsel = _omap3_dpll_compute_freqsel(clk, dd->last_rounded_n); 671 WARN_ON(!freqsel); 672 } 673 674 pr_debug("%s: %s: set rate: locking rate to %lu.\n", __func__, 675 clk_hw_get_name(hw), rate); 676 677 ret = omap3_noncore_dpll_program(clk, freqsel); 678 679 return ret; 680 } 681 682 /** 683 * omap3_noncore_dpll_set_rate_and_parent - set rate and parent for a DPLL clock 684 * @hw: pointer to the clock to set rate and parent for 685 * @rate: target rate for the DPLL 686 * @parent_rate: clock rate of the DPLL parent 687 * @index: new parent index for the DPLL, 0 - reference, 1 - bypass 688 * 689 * Sets rate and parent for a DPLL clock. If new parent is the bypass 690 * clock, only selects the parent. Otherwise proceeds with a rate 691 * change, as this will effectively also change the parent as the 692 * DPLL is put into locked mode. Returns 0 with success, negative error 693 * value otherwise. 694 */ 695 int omap3_noncore_dpll_set_rate_and_parent(struct clk_hw *hw, 696 unsigned long rate, 697 unsigned long parent_rate, 698 u8 index) 699 { 700 int ret; 701 702 if (!hw || !rate) 703 return -EINVAL; 704 705 /* 706 * clk-ref at index[0], in which case we only need to set rate, 707 * the parent will be changed automatically with the lock sequence. 708 * With clk-bypass case we only need to change parent. 709 */ 710 if (index) 711 ret = omap3_noncore_dpll_set_parent(hw, index); 712 else 713 ret = omap3_noncore_dpll_set_rate(hw, rate, parent_rate); 714 715 return ret; 716 } 717 718 /* DPLL autoidle read/set code */ 719 720 /** 721 * omap3_dpll_autoidle_read - read a DPLL's autoidle bits 722 * @clk: struct clk * of the DPLL to read 723 * 724 * Return the DPLL's autoidle bits, shifted down to bit 0. Returns 725 * -EINVAL if passed a null pointer or if the struct clk does not 726 * appear to refer to a DPLL. 727 */ 728 static u32 omap3_dpll_autoidle_read(struct clk_hw_omap *clk) 729 { 730 const struct dpll_data *dd; 731 u32 v; 732 733 if (!clk || !clk->dpll_data) 734 return -EINVAL; 735 736 dd = clk->dpll_data; 737 738 if (!dd->autoidle_mask) 739 return -EINVAL; 740 741 v = ti_clk_ll_ops->clk_readl(&dd->autoidle_reg); 742 v &= dd->autoidle_mask; 743 v >>= __ffs(dd->autoidle_mask); 744 745 return v; 746 } 747 748 /** 749 * omap3_dpll_allow_idle - enable DPLL autoidle bits 750 * @clk: struct clk * of the DPLL to operate on 751 * 752 * Enable DPLL automatic idle control. This automatic idle mode 753 * switching takes effect only when the DPLL is locked, at least on 754 * OMAP3430. The DPLL will enter low-power stop when its downstream 755 * clocks are gated. No return value. 756 */ 757 static void omap3_dpll_allow_idle(struct clk_hw_omap *clk) 758 { 759 const struct dpll_data *dd; 760 u32 v; 761 762 if (!clk || !clk->dpll_data) 763 return; 764 765 dd = clk->dpll_data; 766 767 if (!dd->autoidle_mask) 768 return; 769 770 /* 771 * REVISIT: CORE DPLL can optionally enter low-power bypass 772 * by writing 0x5 instead of 0x1. Add some mechanism to 773 * optionally enter this mode. 774 */ 775 v = ti_clk_ll_ops->clk_readl(&dd->autoidle_reg); 776 v &= ~dd->autoidle_mask; 777 v |= DPLL_AUTOIDLE_LOW_POWER_STOP << __ffs(dd->autoidle_mask); 778 ti_clk_ll_ops->clk_writel(v, &dd->autoidle_reg); 779 } 780 781 /** 782 * omap3_dpll_deny_idle - prevent DPLL from automatically idling 783 * @clk: struct clk * of the DPLL to operate on 784 * 785 * Disable DPLL automatic idle control. No return value. 786 */ 787 static void omap3_dpll_deny_idle(struct clk_hw_omap *clk) 788 { 789 const struct dpll_data *dd; 790 u32 v; 791 792 if (!clk || !clk->dpll_data) 793 return; 794 795 dd = clk->dpll_data; 796 797 if (!dd->autoidle_mask) 798 return; 799 800 v = ti_clk_ll_ops->clk_readl(&dd->autoidle_reg); 801 v &= ~dd->autoidle_mask; 802 v |= DPLL_AUTOIDLE_DISABLE << __ffs(dd->autoidle_mask); 803 ti_clk_ll_ops->clk_writel(v, &dd->autoidle_reg); 804 } 805 806 /* Clock control for DPLL outputs */ 807 808 /* Find the parent DPLL for the given clkoutx2 clock */ 809 static struct clk_hw_omap *omap3_find_clkoutx2_dpll(struct clk_hw *hw) 810 { 811 struct clk_hw_omap *pclk = NULL; 812 813 /* Walk up the parents of clk, looking for a DPLL */ 814 do { 815 do { 816 hw = clk_hw_get_parent(hw); 817 } while (hw && (!omap2_clk_is_hw_omap(hw))); 818 if (!hw) 819 break; 820 pclk = to_clk_hw_omap(hw); 821 } while (pclk && !pclk->dpll_data); 822 823 /* clk does not have a DPLL as a parent? error in the clock data */ 824 if (!pclk) { 825 WARN_ON(1); 826 return NULL; 827 } 828 829 return pclk; 830 } 831 832 /** 833 * omap3_clkoutx2_recalc - recalculate DPLL X2 output virtual clock rate 834 * @hw: pointer struct clk_hw 835 * @parent_rate: clock rate of the DPLL parent 836 * 837 * Using parent clock DPLL data, look up DPLL state. If locked, set our 838 * rate to the dpll_clk * 2; otherwise, just use dpll_clk. 839 */ 840 unsigned long omap3_clkoutx2_recalc(struct clk_hw *hw, 841 unsigned long parent_rate) 842 { 843 const struct dpll_data *dd; 844 unsigned long rate; 845 u32 v; 846 struct clk_hw_omap *pclk = NULL; 847 848 if (!parent_rate) 849 return 0; 850 851 pclk = omap3_find_clkoutx2_dpll(hw); 852 853 if (!pclk) 854 return 0; 855 856 dd = pclk->dpll_data; 857 858 WARN_ON(!dd->enable_mask); 859 860 v = ti_clk_ll_ops->clk_readl(&dd->control_reg) & dd->enable_mask; 861 v >>= __ffs(dd->enable_mask); 862 if ((v != OMAP3XXX_EN_DPLL_LOCKED) || (dd->flags & DPLL_J_TYPE)) 863 rate = parent_rate; 864 else 865 rate = parent_rate * 2; 866 return rate; 867 } 868 869 /** 870 * omap3_core_dpll_save_context - Save the m and n values of the divider 871 * @hw: pointer struct clk_hw 872 * 873 * Before the dpll registers are lost save the last rounded rate m and n 874 * and the enable mask. 875 */ 876 int omap3_core_dpll_save_context(struct clk_hw *hw) 877 { 878 struct clk_hw_omap *clk = to_clk_hw_omap(hw); 879 struct dpll_data *dd; 880 u32 v; 881 882 dd = clk->dpll_data; 883 884 v = ti_clk_ll_ops->clk_readl(&dd->control_reg); 885 clk->context = (v & dd->enable_mask) >> __ffs(dd->enable_mask); 886 887 if (clk->context == DPLL_LOCKED) { 888 v = ti_clk_ll_ops->clk_readl(&dd->mult_div1_reg); 889 dd->last_rounded_m = (v & dd->mult_mask) >> 890 __ffs(dd->mult_mask); 891 dd->last_rounded_n = ((v & dd->div1_mask) >> 892 __ffs(dd->div1_mask)) + 1; 893 } 894 895 return 0; 896 } 897 898 /** 899 * omap3_core_dpll_restore_context - restore the m and n values of the divider 900 * @hw: pointer struct clk_hw 901 * 902 * Restore the last rounded rate m and n 903 * and the enable mask. 904 */ 905 void omap3_core_dpll_restore_context(struct clk_hw *hw) 906 { 907 struct clk_hw_omap *clk = to_clk_hw_omap(hw); 908 const struct dpll_data *dd; 909 u32 v; 910 911 dd = clk->dpll_data; 912 913 if (clk->context == DPLL_LOCKED) { 914 _omap3_dpll_write_clken(clk, 0x4); 915 _omap3_wait_dpll_status(clk, 0); 916 917 v = ti_clk_ll_ops->clk_readl(&dd->mult_div1_reg); 918 v &= ~(dd->mult_mask | dd->div1_mask); 919 v |= dd->last_rounded_m << __ffs(dd->mult_mask); 920 v |= (dd->last_rounded_n - 1) << __ffs(dd->div1_mask); 921 ti_clk_ll_ops->clk_writel(v, &dd->mult_div1_reg); 922 923 _omap3_dpll_write_clken(clk, DPLL_LOCKED); 924 _omap3_wait_dpll_status(clk, 1); 925 } else { 926 _omap3_dpll_write_clken(clk, clk->context); 927 } 928 } 929 930 /** 931 * omap3_noncore_dpll_save_context - Save the m and n values of the divider 932 * @hw: pointer struct clk_hw 933 * 934 * Before the dpll registers are lost save the last rounded rate m and n 935 * and the enable mask. 936 */ 937 int omap3_noncore_dpll_save_context(struct clk_hw *hw) 938 { 939 struct clk_hw_omap *clk = to_clk_hw_omap(hw); 940 struct dpll_data *dd; 941 u32 v; 942 943 dd = clk->dpll_data; 944 945 v = ti_clk_ll_ops->clk_readl(&dd->control_reg); 946 clk->context = (v & dd->enable_mask) >> __ffs(dd->enable_mask); 947 948 if (clk->context == DPLL_LOCKED) { 949 v = ti_clk_ll_ops->clk_readl(&dd->mult_div1_reg); 950 dd->last_rounded_m = (v & dd->mult_mask) >> 951 __ffs(dd->mult_mask); 952 dd->last_rounded_n = ((v & dd->div1_mask) >> 953 __ffs(dd->div1_mask)) + 1; 954 } 955 956 return 0; 957 } 958 959 /** 960 * omap3_noncore_dpll_restore_context - restore the m and n values of the divider 961 * @hw: pointer struct clk_hw 962 * 963 * Restore the last rounded rate m and n 964 * and the enable mask. 965 */ 966 void omap3_noncore_dpll_restore_context(struct clk_hw *hw) 967 { 968 struct clk_hw_omap *clk = to_clk_hw_omap(hw); 969 const struct dpll_data *dd; 970 u32 ctrl, mult_div1; 971 972 dd = clk->dpll_data; 973 974 ctrl = ti_clk_ll_ops->clk_readl(&dd->control_reg); 975 mult_div1 = ti_clk_ll_ops->clk_readl(&dd->mult_div1_reg); 976 977 if (clk->context == ((ctrl & dd->enable_mask) >> 978 __ffs(dd->enable_mask)) && 979 dd->last_rounded_m == ((mult_div1 & dd->mult_mask) >> 980 __ffs(dd->mult_mask)) && 981 dd->last_rounded_n == ((mult_div1 & dd->div1_mask) >> 982 __ffs(dd->div1_mask)) + 1) { 983 /* nothing to be done */ 984 return; 985 } 986 987 if (clk->context == DPLL_LOCKED) 988 omap3_noncore_dpll_program(clk, 0); 989 else 990 _omap3_dpll_write_clken(clk, clk->context); 991 } 992 993 /* OMAP3/4 non-CORE DPLL clkops */ 994 const struct clk_hw_omap_ops clkhwops_omap3_dpll = { 995 .allow_idle = omap3_dpll_allow_idle, 996 .deny_idle = omap3_dpll_deny_idle, 997 }; 998 999 /** 1000 * omap3_dpll4_set_rate - set rate for omap3 per-dpll 1001 * @hw: clock to change 1002 * @rate: target rate for clock 1003 * @parent_rate: clock rate of the DPLL parent 1004 * 1005 * Check if the current SoC supports the per-dpll reprogram operation 1006 * or not, and then do the rate change if supported. Returns -EINVAL 1007 * if not supported, 0 for success, and potential error codes from the 1008 * clock rate change. 1009 */ 1010 int omap3_dpll4_set_rate(struct clk_hw *hw, unsigned long rate, 1011 unsigned long parent_rate) 1012 { 1013 /* 1014 * According to the 12-5 CDP code from TI, "Limitation 2.5" 1015 * on 3430ES1 prevents us from changing DPLL multipliers or dividers 1016 * on DPLL4. 1017 */ 1018 if (ti_clk_get_features()->flags & TI_CLK_DPLL4_DENY_REPROGRAM) { 1019 pr_err("clock: DPLL4 cannot change rate due to silicon 'Limitation 2.5' on 3430ES1.\n"); 1020 return -EINVAL; 1021 } 1022 1023 return omap3_noncore_dpll_set_rate(hw, rate, parent_rate); 1024 } 1025 1026 /** 1027 * omap3_dpll4_set_rate_and_parent - set rate and parent for omap3 per-dpll 1028 * @hw: clock to change 1029 * @rate: target rate for clock 1030 * @parent_rate: rate of the parent clock 1031 * @index: parent index, 0 - reference clock, 1 - bypass clock 1032 * 1033 * Check if the current SoC support the per-dpll reprogram operation 1034 * or not, and then do the rate + parent change if supported. Returns 1035 * -EINVAL if not supported, 0 for success, and potential error codes 1036 * from the clock rate change. 1037 */ 1038 int omap3_dpll4_set_rate_and_parent(struct clk_hw *hw, unsigned long rate, 1039 unsigned long parent_rate, u8 index) 1040 { 1041 if (ti_clk_get_features()->flags & TI_CLK_DPLL4_DENY_REPROGRAM) { 1042 pr_err("clock: DPLL4 cannot change rate due to silicon 'Limitation 2.5' on 3430ES1.\n"); 1043 return -EINVAL; 1044 } 1045 1046 return omap3_noncore_dpll_set_rate_and_parent(hw, rate, parent_rate, 1047 index); 1048 } 1049 1050 /* Apply DM3730 errata sprz319 advisory 2.1. */ 1051 static bool omap3_dpll5_apply_errata(struct clk_hw *hw, 1052 unsigned long parent_rate) 1053 { 1054 struct omap3_dpll5_settings { 1055 unsigned int rate, m, n; 1056 }; 1057 1058 static const struct omap3_dpll5_settings precomputed[] = { 1059 /* 1060 * From DM3730 errata advisory 2.1, table 35 and 36. 1061 * The N value is increased by 1 compared to the tables as the 1062 * errata lists register values while last_rounded_field is the 1063 * real divider value. 1064 */ 1065 { 12000000, 80, 0 + 1 }, 1066 { 13000000, 443, 5 + 1 }, 1067 { 19200000, 50, 0 + 1 }, 1068 { 26000000, 443, 11 + 1 }, 1069 { 38400000, 25, 0 + 1 } 1070 }; 1071 1072 const struct omap3_dpll5_settings *d; 1073 struct clk_hw_omap *clk = to_clk_hw_omap(hw); 1074 struct dpll_data *dd; 1075 unsigned int i; 1076 1077 for (i = 0; i < ARRAY_SIZE(precomputed); ++i) { 1078 if (parent_rate == precomputed[i].rate) 1079 break; 1080 } 1081 1082 if (i == ARRAY_SIZE(precomputed)) 1083 return false; 1084 1085 d = &precomputed[i]; 1086 1087 /* Update the M, N and rounded rate values and program the DPLL. */ 1088 dd = clk->dpll_data; 1089 dd->last_rounded_m = d->m; 1090 dd->last_rounded_n = d->n; 1091 dd->last_rounded_rate = div_u64((u64)parent_rate * d->m, d->n); 1092 omap3_noncore_dpll_program(clk, 0); 1093 1094 return true; 1095 } 1096 1097 /** 1098 * omap3_dpll5_set_rate - set rate for omap3 dpll5 1099 * @hw: clock to change 1100 * @rate: target rate for clock 1101 * @parent_rate: rate of the parent clock 1102 * 1103 * Set rate for the DPLL5 clock. Apply the sprz319 advisory 2.1 on OMAP36xx if 1104 * the DPLL is used for USB host (detected through the requested rate). 1105 */ 1106 int omap3_dpll5_set_rate(struct clk_hw *hw, unsigned long rate, 1107 unsigned long parent_rate) 1108 { 1109 if (rate == OMAP3_DPLL5_FREQ_FOR_USBHOST * 8) { 1110 if (omap3_dpll5_apply_errata(hw, parent_rate)) 1111 return 0; 1112 } 1113 1114 return omap3_noncore_dpll_set_rate(hw, rate, parent_rate); 1115 } 1116