xref: /linux/drivers/clk/renesas/rcar-gen4-cpg.c (revision d53b8e36925256097a08d7cb749198d85cbf9b2b)
1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * R-Car Gen4 Clock Pulse Generator
4  *
5  * Copyright (C) 2021 Renesas Electronics Corp.
6  *
7  * Based on rcar-gen3-cpg.c
8  *
9  * Copyright (C) 2015-2018 Glider bvba
10  * Copyright (C) 2019 Renesas Electronics Corp.
11  */
12 
13 #include <linux/bitfield.h>
14 #include <linux/clk.h>
15 #include <linux/clk-provider.h>
16 #include <linux/device.h>
17 #include <linux/err.h>
18 #include <linux/init.h>
19 #include <linux/io.h>
20 #include <linux/iopoll.h>
21 #include <linux/slab.h>
22 
23 #include "renesas-cpg-mssr.h"
24 #include "rcar-gen4-cpg.h"
25 #include "rcar-cpg-lib.h"
26 
27 static const struct rcar_gen4_cpg_pll_config *cpg_pll_config __initdata;
28 static unsigned int cpg_clk_extalr __initdata;
29 static u32 cpg_mode __initdata;
30 
31 #define CPG_PLLECR		0x0820	/* PLL Enable Control Register */
32 
33 #define CPG_PLLECR_PLLST(n)	BIT(8 + ((n) < 3 ? (n) - 1 : \
34 					 (n) > 3 ? (n) + 1 : n)) /* PLLn Circuit Status */
35 
36 #define CPG_PLL1CR0		0x830	/* PLLn Control Registers */
37 #define CPG_PLL1CR1		0x8b0
38 #define CPG_PLL2CR0		0x834
39 #define CPG_PLL2CR1		0x8b8
40 #define CPG_PLL3CR0		0x83c
41 #define CPG_PLL3CR1		0x8c0
42 #define CPG_PLL4CR0		0x844
43 #define CPG_PLL4CR1		0x8c8
44 #define CPG_PLL6CR0		0x84c
45 #define CPG_PLL6CR1		0x8d8
46 
47 #define CPG_PLLxCR0_KICK	BIT(31)
48 #define CPG_PLLxCR0_NI		GENMASK(27, 20)	/* Integer mult. factor */
49 #define CPG_PLLxCR0_SSMODE	GENMASK(18, 16)	/* PLL mode */
50 #define CPG_PLLxCR0_SSMODE_FM	BIT(18)	/* Fractional Multiplication */
51 #define CPG_PLLxCR0_SSMODE_DITH	BIT(17) /* Frequency Dithering */
52 #define CPG_PLLxCR0_SSMODE_CENT	BIT(16)	/* Center (vs. Down) Spread Dithering */
53 #define CPG_PLLxCR0_SSFREQ	GENMASK(14, 8)	/* SSCG Modulation Frequency */
54 #define CPG_PLLxCR0_SSDEPT	GENMASK(6, 0)	/* SSCG Modulation Depth */
55 
56 #define SSMODE_FM		BIT(2)	/* Fractional Multiplication */
57 #define SSMODE_DITHER		BIT(1)	/* Frequency Dithering */
58 #define SSMODE_CENTER		BIT(0)	/* Center (vs. Down) Spread Dithering */
59 
60 /* PLL Clocks */
61 struct cpg_pll_clk {
62 	struct clk_hw hw;
63 	void __iomem *pllcr0_reg;
64 	void __iomem *pllecr_reg;
65 	u32 pllecr_pllst_mask;
66 };
67 
68 #define to_pll_clk(_hw)   container_of(_hw, struct cpg_pll_clk, hw)
69 
70 static unsigned long cpg_pll_clk_recalc_rate(struct clk_hw *hw,
71 					     unsigned long parent_rate)
72 {
73 	struct cpg_pll_clk *pll_clk = to_pll_clk(hw);
74 	unsigned int mult;
75 
76 	mult = FIELD_GET(CPG_PLLxCR0_NI, readl(pll_clk->pllcr0_reg)) + 1;
77 
78 	return parent_rate * mult * 2;
79 }
80 
81 static int cpg_pll_clk_determine_rate(struct clk_hw *hw,
82 				      struct clk_rate_request *req)
83 {
84 	unsigned int min_mult, max_mult, mult;
85 	unsigned long prate;
86 
87 	prate = req->best_parent_rate * 2;
88 	min_mult = max(div64_ul(req->min_rate, prate), 1ULL);
89 	max_mult = min(div64_ul(req->max_rate, prate), 256ULL);
90 	if (max_mult < min_mult)
91 		return -EINVAL;
92 
93 	mult = DIV_ROUND_CLOSEST_ULL(req->rate, prate);
94 	mult = clamp(mult, min_mult, max_mult);
95 
96 	req->rate = prate * mult;
97 	return 0;
98 }
99 
100 static int cpg_pll_clk_set_rate(struct clk_hw *hw, unsigned long rate,
101 				unsigned long parent_rate)
102 {
103 	struct cpg_pll_clk *pll_clk = to_pll_clk(hw);
104 	unsigned int mult;
105 	u32 val;
106 
107 	mult = DIV_ROUND_CLOSEST_ULL(rate, parent_rate * 2);
108 	mult = clamp(mult, 1U, 256U);
109 
110 	if (readl(pll_clk->pllcr0_reg) & CPG_PLLxCR0_KICK)
111 		return -EBUSY;
112 
113 	cpg_reg_modify(pll_clk->pllcr0_reg, CPG_PLLxCR0_NI,
114 		       FIELD_PREP(CPG_PLLxCR0_NI, mult - 1));
115 
116 	/*
117 	 * Set KICK bit in PLLxCR0 to update hardware setting and wait for
118 	 * clock change completion.
119 	 */
120 	cpg_reg_modify(pll_clk->pllcr0_reg, 0, CPG_PLLxCR0_KICK);
121 
122 	/*
123 	 * Note: There is no HW information about the worst case latency.
124 	 *
125 	 * Using experimental measurements, it seems that no more than
126 	 * ~45 µs are needed, independently of the CPU rate.
127 	 * Since this value might be dependent on external xtal rate, pll
128 	 * rate or even the other emulation clocks rate, use 1000 as a
129 	 * "super" safe value.
130 	 */
131 	return readl_poll_timeout(pll_clk->pllecr_reg, val,
132 				  val & pll_clk->pllecr_pllst_mask, 0, 1000);
133 }
134 
135 static const struct clk_ops cpg_pll_clk_ops = {
136 	.recalc_rate = cpg_pll_clk_recalc_rate,
137 	.determine_rate = cpg_pll_clk_determine_rate,
138 	.set_rate = cpg_pll_clk_set_rate,
139 };
140 
141 static struct clk * __init cpg_pll_clk_register(const char *name,
142 						const char *parent_name,
143 						void __iomem *base,
144 						unsigned int cr0_offset,
145 						unsigned int cr1_offset,
146 						unsigned int index)
147 
148 {
149 	struct cpg_pll_clk *pll_clk;
150 	struct clk_init_data init = {};
151 	struct clk *clk;
152 
153 	pll_clk = kzalloc(sizeof(*pll_clk), GFP_KERNEL);
154 	if (!pll_clk)
155 		return ERR_PTR(-ENOMEM);
156 
157 	init.name = name;
158 	init.ops = &cpg_pll_clk_ops;
159 	init.parent_names = &parent_name;
160 	init.num_parents = 1;
161 
162 	pll_clk->hw.init = &init;
163 	pll_clk->pllcr0_reg = base + cr0_offset;
164 	pll_clk->pllecr_reg = base + CPG_PLLECR;
165 	pll_clk->pllecr_pllst_mask = CPG_PLLECR_PLLST(index);
166 
167 	/* Disable Fractional Multiplication and Frequency Dithering */
168 	writel(0, base + cr1_offset);
169 	cpg_reg_modify(pll_clk->pllcr0_reg, CPG_PLLxCR0_SSMODE, 0);
170 
171 	clk = clk_register(NULL, &pll_clk->hw);
172 	if (IS_ERR(clk))
173 		kfree(pll_clk);
174 
175 	return clk;
176 }
177 /*
178  * Z0 Clock & Z1 Clock
179  */
180 #define CPG_FRQCRB			0x00000804
181 #define CPG_FRQCRB_KICK			BIT(31)
182 #define CPG_FRQCRC0			0x00000808
183 #define CPG_FRQCRC1			0x000008e0
184 
185 struct cpg_z_clk {
186 	struct clk_hw hw;
187 	void __iomem *reg;
188 	void __iomem *kick_reg;
189 	unsigned long max_rate;		/* Maximum rate for normal mode */
190 	unsigned int fixed_div;
191 	u32 mask;
192 };
193 
194 #define to_z_clk(_hw)	container_of(_hw, struct cpg_z_clk, hw)
195 
196 static unsigned long cpg_z_clk_recalc_rate(struct clk_hw *hw,
197 					   unsigned long parent_rate)
198 {
199 	struct cpg_z_clk *zclk = to_z_clk(hw);
200 	unsigned int mult;
201 	u32 val;
202 
203 	val = readl(zclk->reg) & zclk->mask;
204 	mult = 32 - (val >> __ffs(zclk->mask));
205 
206 	return DIV_ROUND_CLOSEST_ULL((u64)parent_rate * mult,
207 				     32 * zclk->fixed_div);
208 }
209 
210 static int cpg_z_clk_determine_rate(struct clk_hw *hw,
211 				    struct clk_rate_request *req)
212 {
213 	struct cpg_z_clk *zclk = to_z_clk(hw);
214 	unsigned int min_mult, max_mult, mult;
215 	unsigned long rate, prate;
216 
217 	rate = min(req->rate, req->max_rate);
218 	if (rate <= zclk->max_rate) {
219 		/* Set parent rate to initial value for normal modes */
220 		prate = zclk->max_rate;
221 	} else {
222 		/* Set increased parent rate for boost modes */
223 		prate = rate;
224 	}
225 	req->best_parent_rate = clk_hw_round_rate(clk_hw_get_parent(hw),
226 						  prate * zclk->fixed_div);
227 
228 	prate = req->best_parent_rate / zclk->fixed_div;
229 	min_mult = max(div64_ul(req->min_rate * 32ULL, prate), 1ULL);
230 	max_mult = min(div64_ul(req->max_rate * 32ULL, prate), 32ULL);
231 	if (max_mult < min_mult)
232 		return -EINVAL;
233 
234 	mult = DIV_ROUND_CLOSEST_ULL(rate * 32ULL, prate);
235 	mult = clamp(mult, min_mult, max_mult);
236 
237 	req->rate = DIV_ROUND_CLOSEST_ULL((u64)prate * mult, 32);
238 	return 0;
239 }
240 
241 static int cpg_z_clk_set_rate(struct clk_hw *hw, unsigned long rate,
242 			      unsigned long parent_rate)
243 {
244 	struct cpg_z_clk *zclk = to_z_clk(hw);
245 	unsigned int mult;
246 	unsigned int i;
247 
248 	mult = DIV64_U64_ROUND_CLOSEST(rate * 32ULL * zclk->fixed_div,
249 				       parent_rate);
250 	mult = clamp(mult, 1U, 32U);
251 
252 	if (readl(zclk->kick_reg) & CPG_FRQCRB_KICK)
253 		return -EBUSY;
254 
255 	cpg_reg_modify(zclk->reg, zclk->mask, (32 - mult) << __ffs(zclk->mask));
256 
257 	/*
258 	 * Set KICK bit in FRQCRB to update hardware setting and wait for
259 	 * clock change completion.
260 	 */
261 	cpg_reg_modify(zclk->kick_reg, 0, CPG_FRQCRB_KICK);
262 
263 	/*
264 	 * Note: There is no HW information about the worst case latency.
265 	 *
266 	 * Using experimental measurements, it seems that no more than
267 	 * ~10 iterations are needed, independently of the CPU rate.
268 	 * Since this value might be dependent on external xtal rate, pll1
269 	 * rate or even the other emulation clocks rate, use 1000 as a
270 	 * "super" safe value.
271 	 */
272 	for (i = 1000; i; i--) {
273 		if (!(readl(zclk->kick_reg) & CPG_FRQCRB_KICK))
274 			return 0;
275 
276 		cpu_relax();
277 	}
278 
279 	return -ETIMEDOUT;
280 }
281 
282 static const struct clk_ops cpg_z_clk_ops = {
283 	.recalc_rate = cpg_z_clk_recalc_rate,
284 	.determine_rate = cpg_z_clk_determine_rate,
285 	.set_rate = cpg_z_clk_set_rate,
286 };
287 
288 static struct clk * __init cpg_z_clk_register(const char *name,
289 					      const char *parent_name,
290 					      void __iomem *reg,
291 					      unsigned int div,
292 					      unsigned int offset)
293 {
294 	struct clk_init_data init = {};
295 	struct cpg_z_clk *zclk;
296 	struct clk *clk;
297 
298 	zclk = kzalloc(sizeof(*zclk), GFP_KERNEL);
299 	if (!zclk)
300 		return ERR_PTR(-ENOMEM);
301 
302 	init.name = name;
303 	init.ops = &cpg_z_clk_ops;
304 	init.flags = CLK_SET_RATE_PARENT;
305 	init.parent_names = &parent_name;
306 	init.num_parents = 1;
307 
308 	if (offset < 32) {
309 		zclk->reg = reg + CPG_FRQCRC0;
310 	} else {
311 		zclk->reg = reg + CPG_FRQCRC1;
312 		offset -= 32;
313 	}
314 	zclk->kick_reg = reg + CPG_FRQCRB;
315 	zclk->hw.init = &init;
316 	zclk->mask = GENMASK(offset + 4, offset);
317 	zclk->fixed_div = div; /* PLLVCO x 1/div x SYS-CPU divider */
318 
319 	clk = clk_register(NULL, &zclk->hw);
320 	if (IS_ERR(clk)) {
321 		kfree(zclk);
322 		return clk;
323 	}
324 
325 	zclk->max_rate = clk_hw_get_rate(clk_hw_get_parent(&zclk->hw)) /
326 			 zclk->fixed_div;
327 	return clk;
328 }
329 
330 /*
331  * RPC Clocks
332  */
333 static const struct clk_div_table cpg_rpcsrc_div_table[] = {
334 	{ 0, 4 }, { 1, 6 }, { 2, 5 }, { 3, 6 }, { 0, 0 },
335 };
336 
337 struct clk * __init rcar_gen4_cpg_clk_register(struct device *dev,
338 	const struct cpg_core_clk *core, const struct cpg_mssr_info *info,
339 	struct clk **clks, void __iomem *base,
340 	struct raw_notifier_head *notifiers)
341 {
342 	const struct clk *parent;
343 	unsigned int mult = 1;
344 	unsigned int div = 1;
345 	u32 value;
346 
347 	parent = clks[core->parent & 0xffff];	/* some types use high bits */
348 	if (IS_ERR(parent))
349 		return ERR_CAST(parent);
350 
351 	switch (core->type) {
352 	case CLK_TYPE_GEN4_MAIN:
353 		div = cpg_pll_config->extal_div;
354 		break;
355 
356 	case CLK_TYPE_GEN4_PLL1:
357 		mult = cpg_pll_config->pll1_mult;
358 		div = cpg_pll_config->pll1_div;
359 		break;
360 
361 	case CLK_TYPE_GEN4_PLL2_VAR:
362 		/*
363 		 * PLL2 is implemented as a custom clock, to change the
364 		 * multiplier when cpufreq changes between normal and boost
365 		 * modes.
366 		 */
367 		return cpg_pll_clk_register(core->name, __clk_get_name(parent),
368 					    base, CPG_PLL2CR0, CPG_PLL2CR1, 2);
369 
370 	case CLK_TYPE_GEN4_PLL2:
371 		mult = cpg_pll_config->pll2_mult;
372 		div = cpg_pll_config->pll2_div;
373 		break;
374 
375 	case CLK_TYPE_GEN4_PLL3:
376 		mult = cpg_pll_config->pll3_mult;
377 		div = cpg_pll_config->pll3_div;
378 		break;
379 
380 	case CLK_TYPE_GEN4_PLL4:
381 		mult = cpg_pll_config->pll4_mult;
382 		div = cpg_pll_config->pll4_div;
383 		break;
384 
385 	case CLK_TYPE_GEN4_PLL5:
386 		mult = cpg_pll_config->pll5_mult;
387 		div = cpg_pll_config->pll5_div;
388 		break;
389 
390 	case CLK_TYPE_GEN4_PLL6:
391 		mult = cpg_pll_config->pll6_mult;
392 		div = cpg_pll_config->pll6_div;
393 		break;
394 
395 	case CLK_TYPE_GEN4_PLL2X_3X:
396 		value = readl(base + core->offset);
397 		mult = (((value >> 24) & 0x7f) + 1) * 2;
398 		break;
399 
400 	case CLK_TYPE_GEN4_Z:
401 		return cpg_z_clk_register(core->name, __clk_get_name(parent),
402 					  base, core->div, core->offset);
403 
404 	case CLK_TYPE_GEN4_SDSRC:
405 		div = ((readl(base + SD0CKCR1) >> 29) & 0x03) + 4;
406 		break;
407 
408 	case CLK_TYPE_GEN4_SDH:
409 		return cpg_sdh_clk_register(core->name, base + core->offset,
410 					   __clk_get_name(parent), notifiers);
411 
412 	case CLK_TYPE_GEN4_SD:
413 		return cpg_sd_clk_register(core->name, base + core->offset,
414 					   __clk_get_name(parent));
415 
416 	case CLK_TYPE_GEN4_MDSEL:
417 		/*
418 		 * Clock selectable between two parents and two fixed dividers
419 		 * using a mode pin
420 		 */
421 		if (cpg_mode & BIT(core->offset)) {
422 			div = core->div & 0xffff;
423 		} else {
424 			parent = clks[core->parent >> 16];
425 			if (IS_ERR(parent))
426 				return ERR_CAST(parent);
427 			div = core->div >> 16;
428 		}
429 		mult = 1;
430 		break;
431 
432 	case CLK_TYPE_GEN4_OSC:
433 		/*
434 		 * Clock combining OSC EXTAL predivider and a fixed divider
435 		 */
436 		div = cpg_pll_config->osc_prediv * core->div;
437 		break;
438 
439 	case CLK_TYPE_GEN4_RPCSRC:
440 		return clk_register_divider_table(NULL, core->name,
441 						  __clk_get_name(parent), 0,
442 						  base + CPG_RPCCKCR, 3, 2, 0,
443 						  cpg_rpcsrc_div_table,
444 						  &cpg_lock);
445 
446 	case CLK_TYPE_GEN4_RPC:
447 		return cpg_rpc_clk_register(core->name, base + CPG_RPCCKCR,
448 					    __clk_get_name(parent), notifiers);
449 
450 	case CLK_TYPE_GEN4_RPCD2:
451 		return cpg_rpcd2_clk_register(core->name, base + CPG_RPCCKCR,
452 					      __clk_get_name(parent));
453 
454 	default:
455 		return ERR_PTR(-EINVAL);
456 	}
457 
458 	return clk_register_fixed_factor(NULL, core->name,
459 					 __clk_get_name(parent), 0, mult, div);
460 }
461 
462 int __init rcar_gen4_cpg_init(const struct rcar_gen4_cpg_pll_config *config,
463 			      unsigned int clk_extalr, u32 mode)
464 {
465 	cpg_pll_config = config;
466 	cpg_clk_extalr = clk_extalr;
467 	cpg_mode = mode;
468 
469 	return 0;
470 }
471