1# 2# Character device configuration 3# 4 5menu "Character devices" 6 7source "drivers/tty/Kconfig" 8 9config DEVMEM 10 bool "/dev/mem virtual device support" 11 default y 12 help 13 Say Y here if you want to support the /dev/mem device. 14 The /dev/mem device is used to access areas of physical 15 memory. 16 When in doubt, say "Y". 17 18config DEVKMEM 19 bool "/dev/kmem virtual device support" 20 default y 21 help 22 Say Y here if you want to support the /dev/kmem device. The 23 /dev/kmem device is rarely used, but can be used for certain 24 kind of kernel debugging operations. 25 When in doubt, say "N". 26 27config SGI_SNSC 28 bool "SGI Altix system controller communication support" 29 depends on (IA64_SGI_SN2 || IA64_GENERIC) 30 help 31 If you have an SGI Altix and you want to enable system 32 controller communication from user space (you want this!), 33 say Y. Otherwise, say N. 34 35config SGI_TIOCX 36 bool "SGI TIO CX driver support" 37 depends on (IA64_SGI_SN2 || IA64_GENERIC) 38 help 39 If you have an SGI Altix and you have fpga devices attached 40 to your TIO, say Y here, otherwise say N. 41 42config SGI_MBCS 43 tristate "SGI FPGA Core Services driver support" 44 depends on SGI_TIOCX 45 help 46 If you have an SGI Altix with an attached SABrick 47 say Y or M here, otherwise say N. 48 49source "drivers/tty/serial/Kconfig" 50 51config TTY_PRINTK 52 tristate "TTY driver to output user messages via printk" 53 depends on EXPERT && TTY 54 default n 55 ---help--- 56 If you say Y here, the support for writing user messages (i.e. 57 console messages) via printk is available. 58 59 The feature is useful to inline user messages with kernel 60 messages. 61 In order to use this feature, you should output user messages 62 to /dev/ttyprintk or redirect console to this TTY. 63 64 If unsure, say N. 65 66config BFIN_OTP 67 tristate "Blackfin On-Chip OTP Memory Support" 68 depends on BLACKFIN && (BF51x || BF52x || BF54x) 69 default y 70 help 71 If you say Y here, you will get support for a character device 72 interface into the One Time Programmable memory pages that are 73 stored on the Blackfin processor. This will not get you access 74 to the secure memory pages however. You will need to write your 75 own secure code and reader for that. 76 77 To compile this driver as a module, choose M here: the module 78 will be called bfin-otp. 79 80 If unsure, it is safe to say Y. 81 82config BFIN_OTP_WRITE_ENABLE 83 bool "Enable writing support of OTP pages" 84 depends on BFIN_OTP 85 default n 86 help 87 If you say Y here, you will enable support for writing of the 88 OTP pages. This is dangerous by nature as you can only program 89 the pages once, so only enable this option when you actually 90 need it so as to not inadvertently clobber data. 91 92 If unsure, say N. 93 94config PRINTER 95 tristate "Parallel printer support" 96 depends on PARPORT 97 ---help--- 98 If you intend to attach a printer to the parallel port of your Linux 99 box (as opposed to using a serial printer; if the connector at the 100 printer has 9 or 25 holes ["female"], then it's serial), say Y. 101 Also read the Printing-HOWTO, available from 102 <http://www.tldp.org/docs.html#howto>. 103 104 It is possible to share one parallel port among several devices 105 (e.g. printer and ZIP drive) and it is safe to compile the 106 corresponding drivers into the kernel. 107 108 To compile this driver as a module, choose M here and read 109 <file:Documentation/parport.txt>. The module will be called lp. 110 111 If you have several parallel ports, you can specify which ports to 112 use with the "lp" kernel command line option. (Try "man bootparam" 113 or see the documentation of your boot loader (lilo or loadlin) about 114 how to pass options to the kernel at boot time.) The syntax of the 115 "lp" command line option can be found in <file:drivers/char/lp.c>. 116 117 If you have more than 8 printers, you need to increase the LP_NO 118 macro in lp.c and the PARPORT_MAX macro in parport.h. 119 120config LP_CONSOLE 121 bool "Support for console on line printer" 122 depends on PRINTER 123 ---help--- 124 If you want kernel messages to be printed out as they occur, you 125 can have a console on the printer. This option adds support for 126 doing that; to actually get it to happen you need to pass the 127 option "console=lp0" to the kernel at boot time. 128 129 If the printer is out of paper (or off, or unplugged, or too 130 busy..) the kernel will stall until the printer is ready again. 131 By defining CONSOLE_LP_STRICT to 0 (at your own risk) you 132 can make the kernel continue when this happens, 133 but it'll lose the kernel messages. 134 135 If unsure, say N. 136 137config PPDEV 138 tristate "Support for user-space parallel port device drivers" 139 depends on PARPORT 140 ---help--- 141 Saying Y to this adds support for /dev/parport device nodes. This 142 is needed for programs that want portable access to the parallel 143 port, for instance deviceid (which displays Plug-and-Play device 144 IDs). 145 146 This is the parallel port equivalent of SCSI generic support (sg). 147 It is safe to say N to this -- it is not needed for normal printing 148 or parallel port CD-ROM/disk support. 149 150 To compile this driver as a module, choose M here: the 151 module will be called ppdev. 152 153 If unsure, say N. 154 155source "drivers/tty/hvc/Kconfig" 156 157config VIRTIO_CONSOLE 158 tristate "Virtio console" 159 depends on VIRTIO && TTY 160 select HVC_DRIVER 161 help 162 Virtio console for use with lguest and other hypervisors. 163 164 Also serves as a general-purpose serial device for data 165 transfer between the guest and host. Character devices at 166 /dev/vportNpn will be created when corresponding ports are 167 found, where N is the device number and n is the port number 168 within that device. If specified by the host, a sysfs 169 attribute called 'name' will be populated with a name for 170 the port which can be used by udev scripts to create a 171 symlink to the device. 172 173config IBM_BSR 174 tristate "IBM POWER Barrier Synchronization Register support" 175 depends on PPC_PSERIES 176 help 177 This devices exposes a hardware mechanism for fast synchronization 178 of threads across a large system which avoids bouncing a cacheline 179 between several cores on a system 180 181config POWERNV_OP_PANEL 182 tristate "IBM POWERNV Operator Panel Display support" 183 depends on PPC_POWERNV 184 default m 185 help 186 If you say Y here, a special character device node, /dev/op_panel, 187 will be created which exposes the operator panel display on IBM 188 Power Systems machines with FSPs. 189 190 If you don't require access to the operator panel display from user 191 space, say N. 192 193 If unsure, say M here to build it as a module called powernv-op-panel. 194 195source "drivers/char/ipmi/Kconfig" 196 197config DS1620 198 tristate "NetWinder thermometer support" 199 depends on ARCH_NETWINDER 200 help 201 Say Y here to include support for the thermal management hardware 202 found in the NetWinder. This driver allows the user to control the 203 temperature set points and to read the current temperature. 204 205 It is also possible to say M here to build it as a module (ds1620) 206 It is recommended to be used on a NetWinder, but it is not a 207 necessity. 208 209config NWBUTTON 210 tristate "NetWinder Button" 211 depends on ARCH_NETWINDER 212 ---help--- 213 If you say Y here and create a character device node /dev/nwbutton 214 with major and minor numbers 10 and 158 ("man mknod"), then every 215 time the orange button is pressed a number of times, the number of 216 times the button was pressed will be written to that device. 217 218 This is most useful for applications, as yet unwritten, which 219 perform actions based on how many times the button is pressed in a 220 row. 221 222 Do not hold the button down for too long, as the driver does not 223 alter the behaviour of the hardware reset circuitry attached to the 224 button; it will still execute a hard reset if the button is held 225 down for longer than approximately five seconds. 226 227 To compile this driver as a module, choose M here: the 228 module will be called nwbutton. 229 230 Most people will answer Y to this question and "Reboot Using Button" 231 below to be able to initiate a system shutdown from the button. 232 233config NWBUTTON_REBOOT 234 bool "Reboot Using Button" 235 depends on NWBUTTON 236 help 237 If you say Y here, then you will be able to initiate a system 238 shutdown and reboot by pressing the orange button a number of times. 239 The number of presses to initiate the shutdown is two by default, 240 but this can be altered by modifying the value of NUM_PRESSES_REBOOT 241 in nwbutton.h and recompiling the driver or, if you compile the 242 driver as a module, you can specify the number of presses at load 243 time with "insmod button reboot_count=<something>". 244 245config NWFLASH 246 tristate "NetWinder flash support" 247 depends on ARCH_NETWINDER 248 ---help--- 249 If you say Y here and create a character device /dev/flash with 250 major 10 and minor 160 you can manipulate the flash ROM containing 251 the NetWinder firmware. Be careful as accidentally overwriting the 252 flash contents can render your computer unbootable. On no account 253 allow random users access to this device. :-) 254 255 To compile this driver as a module, choose M here: the 256 module will be called nwflash. 257 258 If you're not sure, say N. 259 260source "drivers/char/hw_random/Kconfig" 261 262config NVRAM 263 tristate "/dev/nvram support" 264 depends on ATARI || X86 || (ARM && RTC_DRV_CMOS) || GENERIC_NVRAM 265 ---help--- 266 If you say Y here and create a character special file /dev/nvram 267 with major number 10 and minor number 144 using mknod ("man mknod"), 268 you get read and write access to the extra bytes of non-volatile 269 memory in the real time clock (RTC), which is contained in every PC 270 and most Ataris. The actual number of bytes varies, depending on the 271 nvram in the system, but is usually 114 (128-14 for the RTC). 272 273 This memory is conventionally called "CMOS RAM" on PCs and "NVRAM" 274 on Ataris. /dev/nvram may be used to view settings there, or to 275 change them (with some utility). It could also be used to frequently 276 save a few bits of very important data that may not be lost over 277 power-off and for which writing to disk is too insecure. Note 278 however that most NVRAM space in a PC belongs to the BIOS and you 279 should NEVER idly tamper with it. See Ralf Brown's interrupt list 280 for a guide to the use of CMOS bytes by your BIOS. 281 282 On Atari machines, /dev/nvram is always configured and does not need 283 to be selected. 284 285 To compile this driver as a module, choose M here: the 286 module will be called nvram. 287 288# 289# These legacy RTC drivers just cause too many conflicts with the generic 290# RTC framework ... let's not even try to coexist any more. 291# 292if RTC_LIB=n 293 294config RTC 295 tristate "Enhanced Real Time Clock Support (legacy PC RTC driver)" 296 depends on ALPHA || (MIPS && MACH_LOONGSON64) || MN10300 297 ---help--- 298 If you say Y here and create a character special file /dev/rtc with 299 major number 10 and minor number 135 using mknod ("man mknod"), you 300 will get access to the real time clock (or hardware clock) built 301 into your computer. 302 303 Every PC has such a clock built in. It can be used to generate 304 signals from as low as 1Hz up to 8192Hz, and can also be used 305 as a 24 hour alarm. It reports status information via the file 306 /proc/driver/rtc and its behaviour is set by various ioctls on 307 /dev/rtc. 308 309 If you run Linux on a multiprocessor machine and said Y to 310 "Symmetric Multi Processing" above, you should say Y here to read 311 and set the RTC in an SMP compatible fashion. 312 313 If you think you have a use for such a device (such as periodic data 314 sampling), then say Y here, and read <file:Documentation/rtc.txt> 315 for details. 316 317 To compile this driver as a module, choose M here: the 318 module will be called rtc. 319 320config JS_RTC 321 tristate "Enhanced Real Time Clock Support" 322 depends on SPARC32 && PCI 323 ---help--- 324 If you say Y here and create a character special file /dev/rtc with 325 major number 10 and minor number 135 using mknod ("man mknod"), you 326 will get access to the real time clock (or hardware clock) built 327 into your computer. 328 329 Every PC has such a clock built in. It can be used to generate 330 signals from as low as 1Hz up to 8192Hz, and can also be used 331 as a 24 hour alarm. It reports status information via the file 332 /proc/driver/rtc and its behaviour is set by various ioctls on 333 /dev/rtc. 334 335 If you think you have a use for such a device (such as periodic data 336 sampling), then say Y here, and read <file:Documentation/rtc.txt> 337 for details. 338 339 To compile this driver as a module, choose M here: the 340 module will be called js-rtc. 341 342config GEN_RTC 343 tristate "Generic /dev/rtc emulation" 344 depends on RTC!=y 345 depends on ALPHA || M68K || MN10300 || PARISC || PPC || X86 346 ---help--- 347 If you say Y here and create a character special file /dev/rtc with 348 major number 10 and minor number 135 using mknod ("man mknod"), you 349 will get access to the real time clock (or hardware clock) built 350 into your computer. 351 352 It reports status information via the file /proc/driver/rtc and its 353 behaviour is set by various ioctls on /dev/rtc. If you enable the 354 "extended RTC operation" below it will also provide an emulation 355 for RTC_UIE which is required by some programs and may improve 356 precision in some cases. 357 358 To compile this driver as a module, choose M here: the 359 module will be called genrtc. 360 361config GEN_RTC_X 362 bool "Extended RTC operation" 363 depends on GEN_RTC 364 help 365 Provides an emulation for RTC_UIE which is required by some programs 366 and may improve precision of the generic RTC support in some cases. 367 368config EFI_RTC 369 bool "EFI Real Time Clock Services" 370 depends on IA64 371 372config DS1302 373 tristate "DS1302 RTC support" 374 depends on M32R && (PLAT_M32700UT || PLAT_OPSPUT) 375 help 376 If you say Y here and create a character special file /dev/rtc with 377 major number 121 and minor number 0 using mknod ("man mknod"), you 378 will get access to the real time clock (or hardware clock) built 379 into your computer. 380 381endif # RTC_LIB 382 383config DTLK 384 tristate "Double Talk PC internal speech card support" 385 depends on ISA 386 help 387 This driver is for the DoubleTalk PC, a speech synthesizer 388 manufactured by RC Systems (<http://www.rcsys.com/>). It is also 389 called the `internal DoubleTalk'. 390 391 To compile this driver as a module, choose M here: the 392 module will be called dtlk. 393 394config XILINX_HWICAP 395 tristate "Xilinx HWICAP Support" 396 depends on XILINX_VIRTEX || MICROBLAZE 397 help 398 This option enables support for Xilinx Internal Configuration 399 Access Port (ICAP) driver. The ICAP is used on Xilinx Virtex 400 FPGA platforms to partially reconfigure the FPGA at runtime. 401 402 If unsure, say N. 403 404config R3964 405 tristate "Siemens R3964 line discipline" 406 depends on TTY 407 ---help--- 408 This driver allows synchronous communication with devices using the 409 Siemens R3964 packet protocol. Unless you are dealing with special 410 hardware like PLCs, you are unlikely to need this. 411 412 To compile this driver as a module, choose M here: the 413 module will be called n_r3964. 414 415 If unsure, say N. 416 417config APPLICOM 418 tristate "Applicom intelligent fieldbus card support" 419 depends on PCI 420 ---help--- 421 This driver provides the kernel-side support for the intelligent 422 fieldbus cards made by Applicom International. More information 423 about these cards can be found on the WWW at the address 424 <http://www.applicom-int.com/>, or by email from David Woodhouse 425 <dwmw2@infradead.org>. 426 427 To compile this driver as a module, choose M here: the 428 module will be called applicom. 429 430 If unsure, say N. 431 432config SONYPI 433 tristate "Sony Vaio Programmable I/O Control Device support" 434 depends on X86_32 && PCI && INPUT 435 ---help--- 436 This driver enables access to the Sony Programmable I/O Control 437 Device which can be found in many (all ?) Sony Vaio laptops. 438 439 If you have one of those laptops, read 440 <file:Documentation/laptops/sonypi.txt>, and say Y or M here. 441 442 To compile this driver as a module, choose M here: the 443 module will be called sonypi. 444 445config GPIO_TB0219 446 tristate "TANBAC TB0219 GPIO support" 447 depends on TANBAC_TB022X 448 select GPIO_VR41XX 449 450source "drivers/char/pcmcia/Kconfig" 451 452config MWAVE 453 tristate "ACP Modem (Mwave) support" 454 depends on X86 && TTY 455 select SERIAL_8250 456 ---help--- 457 The ACP modem (Mwave) for Linux is a WinModem. It is composed of a 458 kernel driver and a user level application. Together these components 459 support direct attachment to public switched telephone networks (PSTNs) 460 and support selected world wide countries. 461 462 This version of the ACP Modem driver supports the IBM Thinkpad 600E, 463 600, and 770 that include on board ACP modem hardware. 464 465 The modem also supports the standard communications port interface 466 (ttySx) and is compatible with the Hayes AT Command Set. 467 468 The user level application needed to use this driver can be found at 469 the IBM Linux Technology Center (LTC) web site: 470 <http://www.ibm.com/linux/ltc/>. 471 472 If you own one of the above IBM Thinkpads which has the Mwave chipset 473 in it, say Y. 474 475 To compile this driver as a module, choose M here: the 476 module will be called mwave. 477 478config SCx200_GPIO 479 tristate "NatSemi SCx200 GPIO Support" 480 depends on SCx200 481 select NSC_GPIO 482 help 483 Give userspace access to the GPIO pins on the National 484 Semiconductor SCx200 processors. 485 486 If compiled as a module, it will be called scx200_gpio. 487 488config PC8736x_GPIO 489 tristate "NatSemi PC8736x GPIO Support" 490 depends on X86_32 && !UML 491 default SCx200_GPIO # mostly N 492 select NSC_GPIO # needed for support routines 493 help 494 Give userspace access to the GPIO pins on the National 495 Semiconductor PC-8736x (x=[03456]) SuperIO chip. The chip 496 has multiple functional units, inc several managed by 497 hwmon/pc87360 driver. Tested with PC-87366 498 499 If compiled as a module, it will be called pc8736x_gpio. 500 501config NSC_GPIO 502 tristate "NatSemi Base GPIO Support" 503 depends on X86_32 504 # selected by SCx200_GPIO and PC8736x_GPIO 505 # what about 2 selectors differing: m != y 506 help 507 Common support used (and needed) by scx200_gpio and 508 pc8736x_gpio drivers. If those drivers are built as 509 modules, this one will be too, named nsc_gpio 510 511config RAW_DRIVER 512 tristate "RAW driver (/dev/raw/rawN)" 513 depends on BLOCK 514 help 515 The raw driver permits block devices to be bound to /dev/raw/rawN. 516 Once bound, I/O against /dev/raw/rawN uses efficient zero-copy I/O. 517 See the raw(8) manpage for more details. 518 519 Applications should preferably open the device (eg /dev/hda1) 520 with the O_DIRECT flag. 521 522config MAX_RAW_DEVS 523 int "Maximum number of RAW devices to support (1-65536)" 524 depends on RAW_DRIVER 525 range 1 65536 526 default "256" 527 help 528 The maximum number of RAW devices that are supported. 529 Default is 256. Increase this number in case you need lots of 530 raw devices. 531 532config HPET 533 bool "HPET - High Precision Event Timer" if (X86 || IA64) 534 default n 535 depends on ACPI 536 help 537 If you say Y here, you will have a miscdevice named "/dev/hpet/". Each 538 open selects one of the timers supported by the HPET. The timers are 539 non-periodic and/or periodic. 540 541config HPET_MMAP 542 bool "Allow mmap of HPET" 543 default y 544 depends on HPET 545 help 546 If you say Y here, user applications will be able to mmap 547 the HPET registers. 548 549config HPET_MMAP_DEFAULT 550 bool "Enable HPET MMAP access by default" 551 default y 552 depends on HPET_MMAP 553 help 554 In some hardware implementations, the page containing HPET 555 registers may also contain other things that shouldn't be 556 exposed to the user. This option selects the default (if 557 kernel parameter hpet_mmap is not set) user access to the 558 registers for applications that require it. 559 560config HANGCHECK_TIMER 561 tristate "Hangcheck timer" 562 depends on X86 || IA64 || PPC64 || S390 563 help 564 The hangcheck-timer module detects when the system has gone 565 out to lunch past a certain margin. It can reboot the system 566 or merely print a warning. 567 568config MMTIMER 569 tristate "MMTIMER Memory mapped RTC for SGI Altix" 570 depends on IA64_GENERIC || IA64_SGI_SN2 571 default y 572 help 573 The mmtimer device allows direct userspace access to the 574 Altix system timer. 575 576config UV_MMTIMER 577 tristate "UV_MMTIMER Memory mapped RTC for SGI UV" 578 depends on X86_UV 579 default m 580 help 581 The uv_mmtimer device allows direct userspace access to the 582 UV system timer. 583 584source "drivers/char/tpm/Kconfig" 585 586config TELCLOCK 587 tristate "Telecom clock driver for ATCA SBC" 588 depends on X86 589 default n 590 help 591 The telecom clock device is specific to the MPCBL0010 and MPCBL0050 592 ATCA computers and allows direct userspace access to the 593 configuration of the telecom clock configuration settings. This 594 device is used for hardware synchronization across the ATCA backplane 595 fabric. Upon loading, the driver exports a sysfs directory, 596 /sys/devices/platform/telco_clock, with a number of files for 597 controlling the behavior of this hardware. 598 599config DEVPORT 600 bool 601 depends on ISA || PCI 602 default y 603 604source "drivers/s390/char/Kconfig" 605 606config TILE_SROM 607 bool "Character-device access via hypervisor to the Tilera SPI ROM" 608 depends on TILE 609 default y 610 ---help--- 611 This device provides character-level read-write access 612 to the SROM, typically via the "0", "1", and "2" devices 613 in /dev/srom/. The Tilera hypervisor makes the flash 614 device appear much like a simple EEPROM, and knows 615 how to partition a single ROM for multiple purposes. 616 617source "drivers/char/xillybus/Kconfig" 618 619endmenu 620 621