1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * RSB (Reduced Serial Bus) driver. 4 * 5 * Author: Chen-Yu Tsai <wens@csie.org> 6 * 7 * The RSB controller looks like an SMBus controller which only supports 8 * byte and word data transfers. But, it differs from standard SMBus 9 * protocol on several aspects: 10 * - it uses addresses set at runtime to address slaves. Runtime addresses 11 * are sent to slaves using their 12bit hardware addresses. Up to 15 12 * runtime addresses are available. 13 * - it adds a parity bit every 8bits of data and address for read and 14 * write accesses; this replaces the ack bit 15 * - only one read access is required to read a byte (instead of a write 16 * followed by a read access in standard SMBus protocol) 17 * - there's no Ack bit after each read access 18 * 19 * This means this bus cannot be used to interface with standard SMBus 20 * devices. Devices known to support this interface include the AXP223, 21 * AXP809, and AXP806 PMICs, and the AC100 audio codec, all from X-Powers. 22 * 23 * A description of the operation and wire protocol can be found in the 24 * RSB section of Allwinner's A80 user manual, which can be found at 25 * 26 * https://github.com/allwinner-zh/documents/tree/master/A80 27 * 28 * This document is officially released by Allwinner. 29 * 30 * This driver is based on i2c-sun6i-p2wi.c, the P2WI bus driver. 31 */ 32 33 #include <linux/clk.h> 34 #include <linux/clk/clk-conf.h> 35 #include <linux/device.h> 36 #include <linux/interrupt.h> 37 #include <linux/io.h> 38 #include <linux/iopoll.h> 39 #include <linux/module.h> 40 #include <linux/of.h> 41 #include <linux/of_irq.h> 42 #include <linux/of_device.h> 43 #include <linux/platform_device.h> 44 #include <linux/pm.h> 45 #include <linux/pm_runtime.h> 46 #include <linux/regmap.h> 47 #include <linux/reset.h> 48 #include <linux/slab.h> 49 #include <linux/sunxi-rsb.h> 50 #include <linux/types.h> 51 52 /* RSB registers */ 53 #define RSB_CTRL 0x0 /* Global control */ 54 #define RSB_CCR 0x4 /* Clock control */ 55 #define RSB_INTE 0x8 /* Interrupt controls */ 56 #define RSB_INTS 0xc /* Interrupt status */ 57 #define RSB_ADDR 0x10 /* Address to send with read/write command */ 58 #define RSB_DATA 0x1c /* Data to read/write */ 59 #define RSB_LCR 0x24 /* Line control */ 60 #define RSB_DMCR 0x28 /* Device mode (init) control */ 61 #define RSB_CMD 0x2c /* RSB Command */ 62 #define RSB_DAR 0x30 /* Device address / runtime address */ 63 64 /* CTRL fields */ 65 #define RSB_CTRL_START_TRANS BIT(7) 66 #define RSB_CTRL_ABORT_TRANS BIT(6) 67 #define RSB_CTRL_GLOBAL_INT_ENB BIT(1) 68 #define RSB_CTRL_SOFT_RST BIT(0) 69 70 /* CLK CTRL fields */ 71 #define RSB_CCR_SDA_OUT_DELAY(v) (((v) & 0x7) << 8) 72 #define RSB_CCR_MAX_CLK_DIV 0xff 73 #define RSB_CCR_CLK_DIV(v) ((v) & RSB_CCR_MAX_CLK_DIV) 74 75 /* STATUS fields */ 76 #define RSB_INTS_TRANS_ERR_ACK BIT(16) 77 #define RSB_INTS_TRANS_ERR_DATA_BIT(v) (((v) >> 8) & 0xf) 78 #define RSB_INTS_TRANS_ERR_DATA GENMASK(11, 8) 79 #define RSB_INTS_LOAD_BSY BIT(2) 80 #define RSB_INTS_TRANS_ERR BIT(1) 81 #define RSB_INTS_TRANS_OVER BIT(0) 82 83 /* LINE CTRL fields*/ 84 #define RSB_LCR_SCL_STATE BIT(5) 85 #define RSB_LCR_SDA_STATE BIT(4) 86 #define RSB_LCR_SCL_CTL BIT(3) 87 #define RSB_LCR_SCL_CTL_EN BIT(2) 88 #define RSB_LCR_SDA_CTL BIT(1) 89 #define RSB_LCR_SDA_CTL_EN BIT(0) 90 91 /* DEVICE MODE CTRL field values */ 92 #define RSB_DMCR_DEVICE_START BIT(31) 93 #define RSB_DMCR_MODE_DATA (0x7c << 16) 94 #define RSB_DMCR_MODE_REG (0x3e << 8) 95 #define RSB_DMCR_DEV_ADDR 0x00 96 97 /* CMD values */ 98 #define RSB_CMD_RD8 0x8b 99 #define RSB_CMD_RD16 0x9c 100 #define RSB_CMD_RD32 0xa6 101 #define RSB_CMD_WR8 0x4e 102 #define RSB_CMD_WR16 0x59 103 #define RSB_CMD_WR32 0x63 104 #define RSB_CMD_STRA 0xe8 105 106 /* DAR fields */ 107 #define RSB_DAR_RTA(v) (((v) & 0xff) << 16) 108 #define RSB_DAR_DA(v) ((v) & 0xffff) 109 110 #define RSB_MAX_FREQ 20000000 111 112 #define RSB_CTRL_NAME "sunxi-rsb" 113 114 struct sunxi_rsb_addr_map { 115 u16 hwaddr; 116 u8 rtaddr; 117 }; 118 119 struct sunxi_rsb { 120 struct device *dev; 121 void __iomem *regs; 122 struct clk *clk; 123 struct reset_control *rstc; 124 struct completion complete; 125 struct mutex lock; 126 unsigned int status; 127 u32 clk_freq; 128 }; 129 130 /* bus / slave device related functions */ 131 static const struct bus_type sunxi_rsb_bus; 132 133 static int sunxi_rsb_device_match(struct device *dev, const struct device_driver *drv) 134 { 135 return of_driver_match_device(dev, drv); 136 } 137 138 static int sunxi_rsb_device_probe(struct device *dev) 139 { 140 const struct sunxi_rsb_driver *drv = to_sunxi_rsb_driver(dev->driver); 141 struct sunxi_rsb_device *rdev = to_sunxi_rsb_device(dev); 142 int ret; 143 144 if (!drv->probe) 145 return -ENODEV; 146 147 if (!rdev->irq) { 148 int irq = -ENOENT; 149 150 if (dev->of_node) 151 irq = of_irq_get(dev->of_node, 0); 152 153 if (irq == -EPROBE_DEFER) 154 return irq; 155 if (irq < 0) 156 irq = 0; 157 158 rdev->irq = irq; 159 } 160 161 ret = of_clk_set_defaults(dev->of_node, false); 162 if (ret < 0) 163 return ret; 164 165 return drv->probe(rdev); 166 } 167 168 static void sunxi_rsb_device_remove(struct device *dev) 169 { 170 const struct sunxi_rsb_driver *drv = to_sunxi_rsb_driver(dev->driver); 171 172 drv->remove(to_sunxi_rsb_device(dev)); 173 } 174 175 static int sunxi_rsb_device_modalias(const struct device *dev, struct kobj_uevent_env *env) 176 { 177 return of_device_uevent_modalias(dev, env); 178 } 179 180 static const struct bus_type sunxi_rsb_bus = { 181 .name = RSB_CTRL_NAME, 182 .match = sunxi_rsb_device_match, 183 .probe = sunxi_rsb_device_probe, 184 .remove = sunxi_rsb_device_remove, 185 .uevent = sunxi_rsb_device_modalias, 186 }; 187 188 static void sunxi_rsb_dev_release(struct device *dev) 189 { 190 struct sunxi_rsb_device *rdev = to_sunxi_rsb_device(dev); 191 192 kfree(rdev); 193 } 194 195 /** 196 * sunxi_rsb_device_create() - allocate and add an RSB device 197 * @rsb: RSB controller 198 * @node: RSB slave device node 199 * @hwaddr: RSB slave hardware address 200 * @rtaddr: RSB slave runtime address 201 */ 202 static struct sunxi_rsb_device *sunxi_rsb_device_create(struct sunxi_rsb *rsb, 203 struct device_node *node, u16 hwaddr, u8 rtaddr) 204 { 205 int err; 206 struct sunxi_rsb_device *rdev; 207 208 rdev = kzalloc(sizeof(*rdev), GFP_KERNEL); 209 if (!rdev) 210 return ERR_PTR(-ENOMEM); 211 212 rdev->rsb = rsb; 213 rdev->hwaddr = hwaddr; 214 rdev->rtaddr = rtaddr; 215 rdev->dev.bus = &sunxi_rsb_bus; 216 rdev->dev.parent = rsb->dev; 217 rdev->dev.of_node = node; 218 rdev->dev.release = sunxi_rsb_dev_release; 219 220 dev_set_name(&rdev->dev, "%s-%x", RSB_CTRL_NAME, hwaddr); 221 222 err = device_register(&rdev->dev); 223 if (err < 0) { 224 dev_err(&rdev->dev, "Can't add %s, status %d\n", 225 dev_name(&rdev->dev), err); 226 goto err_device_add; 227 } 228 229 dev_dbg(&rdev->dev, "device %s registered\n", dev_name(&rdev->dev)); 230 231 return rdev; 232 233 err_device_add: 234 put_device(&rdev->dev); 235 236 return ERR_PTR(err); 237 } 238 239 /** 240 * sunxi_rsb_device_unregister(): unregister an RSB device 241 * @rdev: rsb_device to be removed 242 */ 243 static void sunxi_rsb_device_unregister(struct sunxi_rsb_device *rdev) 244 { 245 device_unregister(&rdev->dev); 246 } 247 248 static int sunxi_rsb_remove_devices(struct device *dev, void *data) 249 { 250 struct sunxi_rsb_device *rdev = to_sunxi_rsb_device(dev); 251 252 if (dev->bus == &sunxi_rsb_bus) 253 sunxi_rsb_device_unregister(rdev); 254 255 return 0; 256 } 257 258 /** 259 * sunxi_rsb_driver_register() - Register device driver with RSB core 260 * @rdrv: device driver to be associated with slave-device. 261 * 262 * This API will register the client driver with the RSB framework. 263 * It is typically called from the driver's module-init function. 264 */ 265 int sunxi_rsb_driver_register(struct sunxi_rsb_driver *rdrv) 266 { 267 rdrv->driver.bus = &sunxi_rsb_bus; 268 return driver_register(&rdrv->driver); 269 } 270 EXPORT_SYMBOL_GPL(sunxi_rsb_driver_register); 271 272 /* common code that starts a transfer */ 273 static int _sunxi_rsb_run_xfer(struct sunxi_rsb *rsb) 274 { 275 u32 int_mask, status; 276 bool timeout; 277 278 if (readl(rsb->regs + RSB_CTRL) & RSB_CTRL_START_TRANS) { 279 dev_dbg(rsb->dev, "RSB transfer still in progress\n"); 280 return -EBUSY; 281 } 282 283 reinit_completion(&rsb->complete); 284 285 int_mask = RSB_INTS_LOAD_BSY | RSB_INTS_TRANS_ERR | RSB_INTS_TRANS_OVER; 286 writel(int_mask, rsb->regs + RSB_INTE); 287 writel(RSB_CTRL_START_TRANS | RSB_CTRL_GLOBAL_INT_ENB, 288 rsb->regs + RSB_CTRL); 289 290 if (irqs_disabled()) { 291 timeout = readl_poll_timeout_atomic(rsb->regs + RSB_INTS, 292 status, (status & int_mask), 293 10, 100000); 294 writel(status, rsb->regs + RSB_INTS); 295 } else { 296 timeout = !wait_for_completion_io_timeout(&rsb->complete, 297 msecs_to_jiffies(100)); 298 status = rsb->status; 299 } 300 301 if (timeout) { 302 dev_dbg(rsb->dev, "RSB timeout\n"); 303 304 /* abort the transfer */ 305 writel(RSB_CTRL_ABORT_TRANS, rsb->regs + RSB_CTRL); 306 307 /* clear any interrupt flags */ 308 writel(readl(rsb->regs + RSB_INTS), rsb->regs + RSB_INTS); 309 310 return -ETIMEDOUT; 311 } 312 313 if (status & RSB_INTS_LOAD_BSY) { 314 dev_dbg(rsb->dev, "RSB busy\n"); 315 return -EBUSY; 316 } 317 318 if (status & RSB_INTS_TRANS_ERR) { 319 if (status & RSB_INTS_TRANS_ERR_ACK) { 320 dev_dbg(rsb->dev, "RSB slave nack\n"); 321 return -EINVAL; 322 } 323 324 if (status & RSB_INTS_TRANS_ERR_DATA) { 325 dev_dbg(rsb->dev, "RSB transfer data error\n"); 326 return -EIO; 327 } 328 } 329 330 return 0; 331 } 332 333 static int sunxi_rsb_read(struct sunxi_rsb *rsb, u8 rtaddr, u8 addr, 334 u32 *buf, size_t len) 335 { 336 u32 cmd; 337 int ret; 338 339 if (!buf) 340 return -EINVAL; 341 342 switch (len) { 343 case 1: 344 cmd = RSB_CMD_RD8; 345 break; 346 case 2: 347 cmd = RSB_CMD_RD16; 348 break; 349 case 4: 350 cmd = RSB_CMD_RD32; 351 break; 352 default: 353 dev_err(rsb->dev, "Invalid access width: %zd\n", len); 354 return -EINVAL; 355 } 356 357 ret = pm_runtime_resume_and_get(rsb->dev); 358 if (ret) 359 return ret; 360 361 mutex_lock(&rsb->lock); 362 363 writel(addr, rsb->regs + RSB_ADDR); 364 writel(RSB_DAR_RTA(rtaddr), rsb->regs + RSB_DAR); 365 writel(cmd, rsb->regs + RSB_CMD); 366 367 ret = _sunxi_rsb_run_xfer(rsb); 368 if (ret) 369 goto unlock; 370 371 *buf = readl(rsb->regs + RSB_DATA) & GENMASK(len * 8 - 1, 0); 372 373 unlock: 374 mutex_unlock(&rsb->lock); 375 376 pm_runtime_mark_last_busy(rsb->dev); 377 pm_runtime_put_autosuspend(rsb->dev); 378 379 return ret; 380 } 381 382 static int sunxi_rsb_write(struct sunxi_rsb *rsb, u8 rtaddr, u8 addr, 383 const u32 *buf, size_t len) 384 { 385 u32 cmd; 386 int ret; 387 388 if (!buf) 389 return -EINVAL; 390 391 switch (len) { 392 case 1: 393 cmd = RSB_CMD_WR8; 394 break; 395 case 2: 396 cmd = RSB_CMD_WR16; 397 break; 398 case 4: 399 cmd = RSB_CMD_WR32; 400 break; 401 default: 402 dev_err(rsb->dev, "Invalid access width: %zd\n", len); 403 return -EINVAL; 404 } 405 406 ret = pm_runtime_resume_and_get(rsb->dev); 407 if (ret) 408 return ret; 409 410 mutex_lock(&rsb->lock); 411 412 writel(addr, rsb->regs + RSB_ADDR); 413 writel(RSB_DAR_RTA(rtaddr), rsb->regs + RSB_DAR); 414 writel(*buf, rsb->regs + RSB_DATA); 415 writel(cmd, rsb->regs + RSB_CMD); 416 ret = _sunxi_rsb_run_xfer(rsb); 417 418 mutex_unlock(&rsb->lock); 419 420 pm_runtime_mark_last_busy(rsb->dev); 421 pm_runtime_put_autosuspend(rsb->dev); 422 423 return ret; 424 } 425 426 /* RSB regmap functions */ 427 struct sunxi_rsb_ctx { 428 struct sunxi_rsb_device *rdev; 429 int size; 430 }; 431 432 static int regmap_sunxi_rsb_reg_read(void *context, unsigned int reg, 433 unsigned int *val) 434 { 435 struct sunxi_rsb_ctx *ctx = context; 436 struct sunxi_rsb_device *rdev = ctx->rdev; 437 438 if (reg > 0xff) 439 return -EINVAL; 440 441 return sunxi_rsb_read(rdev->rsb, rdev->rtaddr, reg, val, ctx->size); 442 } 443 444 static int regmap_sunxi_rsb_reg_write(void *context, unsigned int reg, 445 unsigned int val) 446 { 447 struct sunxi_rsb_ctx *ctx = context; 448 struct sunxi_rsb_device *rdev = ctx->rdev; 449 450 return sunxi_rsb_write(rdev->rsb, rdev->rtaddr, reg, &val, ctx->size); 451 } 452 453 static void regmap_sunxi_rsb_free_ctx(void *context) 454 { 455 struct sunxi_rsb_ctx *ctx = context; 456 457 kfree(ctx); 458 } 459 460 static const struct regmap_bus regmap_sunxi_rsb = { 461 .reg_write = regmap_sunxi_rsb_reg_write, 462 .reg_read = regmap_sunxi_rsb_reg_read, 463 .free_context = regmap_sunxi_rsb_free_ctx, 464 .reg_format_endian_default = REGMAP_ENDIAN_NATIVE, 465 .val_format_endian_default = REGMAP_ENDIAN_NATIVE, 466 }; 467 468 static struct sunxi_rsb_ctx *regmap_sunxi_rsb_init_ctx(struct sunxi_rsb_device *rdev, 469 const struct regmap_config *config) 470 { 471 struct sunxi_rsb_ctx *ctx; 472 473 switch (config->val_bits) { 474 case 8: 475 case 16: 476 case 32: 477 break; 478 default: 479 return ERR_PTR(-EINVAL); 480 } 481 482 ctx = kzalloc(sizeof(*ctx), GFP_KERNEL); 483 if (!ctx) 484 return ERR_PTR(-ENOMEM); 485 486 ctx->rdev = rdev; 487 ctx->size = config->val_bits / 8; 488 489 return ctx; 490 } 491 492 struct regmap *__devm_regmap_init_sunxi_rsb(struct sunxi_rsb_device *rdev, 493 const struct regmap_config *config, 494 struct lock_class_key *lock_key, 495 const char *lock_name) 496 { 497 struct sunxi_rsb_ctx *ctx = regmap_sunxi_rsb_init_ctx(rdev, config); 498 499 if (IS_ERR(ctx)) 500 return ERR_CAST(ctx); 501 502 return __devm_regmap_init(&rdev->dev, ®map_sunxi_rsb, ctx, config, 503 lock_key, lock_name); 504 } 505 EXPORT_SYMBOL_GPL(__devm_regmap_init_sunxi_rsb); 506 507 /* RSB controller driver functions */ 508 static irqreturn_t sunxi_rsb_irq(int irq, void *dev_id) 509 { 510 struct sunxi_rsb *rsb = dev_id; 511 u32 status; 512 513 status = readl(rsb->regs + RSB_INTS); 514 rsb->status = status; 515 516 /* Clear interrupts */ 517 status &= (RSB_INTS_LOAD_BSY | RSB_INTS_TRANS_ERR | 518 RSB_INTS_TRANS_OVER); 519 writel(status, rsb->regs + RSB_INTS); 520 521 complete(&rsb->complete); 522 523 return IRQ_HANDLED; 524 } 525 526 static int sunxi_rsb_init_device_mode(struct sunxi_rsb *rsb) 527 { 528 int ret = 0; 529 u32 reg; 530 531 /* send init sequence */ 532 writel(RSB_DMCR_DEVICE_START | RSB_DMCR_MODE_DATA | 533 RSB_DMCR_MODE_REG | RSB_DMCR_DEV_ADDR, rsb->regs + RSB_DMCR); 534 535 readl_poll_timeout(rsb->regs + RSB_DMCR, reg, 536 !(reg & RSB_DMCR_DEVICE_START), 100, 250000); 537 if (reg & RSB_DMCR_DEVICE_START) 538 ret = -ETIMEDOUT; 539 540 /* clear interrupt status bits */ 541 writel(readl(rsb->regs + RSB_INTS), rsb->regs + RSB_INTS); 542 543 return ret; 544 } 545 546 /* 547 * There are 15 valid runtime addresses, though Allwinner typically 548 * skips the first, for unknown reasons, and uses the following three. 549 * 550 * 0x17, 0x2d, 0x3a, 0x4e, 0x59, 0x63, 0x74, 0x8b, 551 * 0x9c, 0xa6, 0xb1, 0xc5, 0xd2, 0xe8, 0xff 552 * 553 * No designs with 2 RSB slave devices sharing identical hardware 554 * addresses on the same bus have been seen in the wild. All designs 555 * use 0x2d for the primary PMIC, 0x3a for the secondary PMIC if 556 * there is one, and 0x45 for peripheral ICs. 557 * 558 * The hardware does not seem to support re-setting runtime addresses. 559 * Attempts to do so result in the slave devices returning a NACK. 560 * Hence we just hardcode the mapping here, like Allwinner does. 561 */ 562 563 static const struct sunxi_rsb_addr_map sunxi_rsb_addr_maps[] = { 564 { 0x3a3, 0x2d }, /* Primary PMIC: AXP223, AXP809, AXP81X, ... */ 565 { 0x745, 0x3a }, /* Secondary PMIC: AXP806, ... */ 566 { 0xe89, 0x4e }, /* Peripheral IC: AC100, ... */ 567 }; 568 569 static u8 sunxi_rsb_get_rtaddr(u16 hwaddr) 570 { 571 int i; 572 573 for (i = 0; i < ARRAY_SIZE(sunxi_rsb_addr_maps); i++) 574 if (hwaddr == sunxi_rsb_addr_maps[i].hwaddr) 575 return sunxi_rsb_addr_maps[i].rtaddr; 576 577 return 0; /* 0 is an invalid runtime address */ 578 } 579 580 static int of_rsb_register_devices(struct sunxi_rsb *rsb) 581 { 582 struct device *dev = rsb->dev; 583 struct device_node *child, *np = dev->of_node; 584 u32 hwaddr; 585 u8 rtaddr; 586 int ret; 587 588 if (!np) 589 return -EINVAL; 590 591 /* Runtime addresses for all slaves should be set first */ 592 for_each_available_child_of_node(np, child) { 593 dev_dbg(dev, "setting child %pOF runtime address\n", 594 child); 595 596 ret = of_property_read_u32(child, "reg", &hwaddr); 597 if (ret) { 598 dev_err(dev, "%pOF: invalid 'reg' property: %d\n", 599 child, ret); 600 continue; 601 } 602 603 rtaddr = sunxi_rsb_get_rtaddr(hwaddr); 604 if (!rtaddr) { 605 dev_err(dev, "%pOF: unknown hardware device address\n", 606 child); 607 continue; 608 } 609 610 /* 611 * Since no devices have been registered yet, we are the 612 * only ones using the bus, we can skip locking the bus. 613 */ 614 615 /* setup command parameters */ 616 writel(RSB_CMD_STRA, rsb->regs + RSB_CMD); 617 writel(RSB_DAR_RTA(rtaddr) | RSB_DAR_DA(hwaddr), 618 rsb->regs + RSB_DAR); 619 620 /* send command */ 621 ret = _sunxi_rsb_run_xfer(rsb); 622 if (ret) 623 dev_warn(dev, "%pOF: set runtime address failed: %d\n", 624 child, ret); 625 } 626 627 /* Then we start adding devices and probing them */ 628 for_each_available_child_of_node(np, child) { 629 struct sunxi_rsb_device *rdev; 630 631 dev_dbg(dev, "adding child %pOF\n", child); 632 633 ret = of_property_read_u32(child, "reg", &hwaddr); 634 if (ret) 635 continue; 636 637 rtaddr = sunxi_rsb_get_rtaddr(hwaddr); 638 if (!rtaddr) 639 continue; 640 641 rdev = sunxi_rsb_device_create(rsb, child, hwaddr, rtaddr); 642 if (IS_ERR(rdev)) 643 dev_err(dev, "failed to add child device %pOF: %ld\n", 644 child, PTR_ERR(rdev)); 645 } 646 647 return 0; 648 } 649 650 static int sunxi_rsb_hw_init(struct sunxi_rsb *rsb) 651 { 652 struct device *dev = rsb->dev; 653 unsigned long p_clk_freq; 654 u32 clk_delay, reg; 655 int clk_div, ret; 656 657 ret = clk_prepare_enable(rsb->clk); 658 if (ret) { 659 dev_err(dev, "failed to enable clk: %d\n", ret); 660 return ret; 661 } 662 663 ret = reset_control_deassert(rsb->rstc); 664 if (ret) { 665 dev_err(dev, "failed to deassert reset line: %d\n", ret); 666 goto err_clk_disable; 667 } 668 669 /* reset the controller */ 670 writel(RSB_CTRL_SOFT_RST, rsb->regs + RSB_CTRL); 671 readl_poll_timeout(rsb->regs + RSB_CTRL, reg, 672 !(reg & RSB_CTRL_SOFT_RST), 1000, 100000); 673 674 /* 675 * Clock frequency and delay calculation code is from 676 * Allwinner U-boot sources. 677 * 678 * From A83 user manual: 679 * bus clock frequency = parent clock frequency / (2 * (divider + 1)) 680 */ 681 p_clk_freq = clk_get_rate(rsb->clk); 682 clk_div = p_clk_freq / rsb->clk_freq / 2; 683 if (!clk_div) 684 clk_div = 1; 685 else if (clk_div > RSB_CCR_MAX_CLK_DIV + 1) 686 clk_div = RSB_CCR_MAX_CLK_DIV + 1; 687 688 clk_delay = clk_div >> 1; 689 if (!clk_delay) 690 clk_delay = 1; 691 692 dev_info(dev, "RSB running at %lu Hz\n", p_clk_freq / clk_div / 2); 693 writel(RSB_CCR_SDA_OUT_DELAY(clk_delay) | RSB_CCR_CLK_DIV(clk_div - 1), 694 rsb->regs + RSB_CCR); 695 696 return 0; 697 698 err_clk_disable: 699 clk_disable_unprepare(rsb->clk); 700 701 return ret; 702 } 703 704 static void sunxi_rsb_hw_exit(struct sunxi_rsb *rsb) 705 { 706 reset_control_assert(rsb->rstc); 707 708 /* Keep the clock and PM reference counts consistent. */ 709 if (!pm_runtime_status_suspended(rsb->dev)) 710 clk_disable_unprepare(rsb->clk); 711 } 712 713 static int __maybe_unused sunxi_rsb_runtime_suspend(struct device *dev) 714 { 715 struct sunxi_rsb *rsb = dev_get_drvdata(dev); 716 717 clk_disable_unprepare(rsb->clk); 718 719 return 0; 720 } 721 722 static int __maybe_unused sunxi_rsb_runtime_resume(struct device *dev) 723 { 724 struct sunxi_rsb *rsb = dev_get_drvdata(dev); 725 726 return clk_prepare_enable(rsb->clk); 727 } 728 729 static int __maybe_unused sunxi_rsb_suspend(struct device *dev) 730 { 731 struct sunxi_rsb *rsb = dev_get_drvdata(dev); 732 733 sunxi_rsb_hw_exit(rsb); 734 735 return 0; 736 } 737 738 static int __maybe_unused sunxi_rsb_resume(struct device *dev) 739 { 740 struct sunxi_rsb *rsb = dev_get_drvdata(dev); 741 742 return sunxi_rsb_hw_init(rsb); 743 } 744 745 static int sunxi_rsb_probe(struct platform_device *pdev) 746 { 747 struct device *dev = &pdev->dev; 748 struct device_node *np = dev->of_node; 749 struct sunxi_rsb *rsb; 750 u32 clk_freq = 3000000; 751 int irq, ret; 752 753 of_property_read_u32(np, "clock-frequency", &clk_freq); 754 if (clk_freq > RSB_MAX_FREQ) 755 return dev_err_probe(dev, -EINVAL, 756 "clock-frequency (%u Hz) is too high (max = 20MHz)\n", 757 clk_freq); 758 759 rsb = devm_kzalloc(dev, sizeof(*rsb), GFP_KERNEL); 760 if (!rsb) 761 return -ENOMEM; 762 763 rsb->dev = dev; 764 rsb->clk_freq = clk_freq; 765 platform_set_drvdata(pdev, rsb); 766 rsb->regs = devm_platform_ioremap_resource(pdev, 0); 767 if (IS_ERR(rsb->regs)) 768 return PTR_ERR(rsb->regs); 769 770 irq = platform_get_irq(pdev, 0); 771 if (irq < 0) 772 return irq; 773 774 rsb->clk = devm_clk_get(dev, NULL); 775 if (IS_ERR(rsb->clk)) 776 return dev_err_probe(dev, PTR_ERR(rsb->clk), 777 "failed to retrieve clk\n"); 778 779 rsb->rstc = devm_reset_control_get(dev, NULL); 780 if (IS_ERR(rsb->rstc)) 781 return dev_err_probe(dev, PTR_ERR(rsb->rstc), 782 "failed to retrieve reset controller\n"); 783 784 init_completion(&rsb->complete); 785 mutex_init(&rsb->lock); 786 787 ret = devm_request_irq(dev, irq, sunxi_rsb_irq, 0, RSB_CTRL_NAME, rsb); 788 if (ret) 789 return dev_err_probe(dev, ret, 790 "can't register interrupt handler irq %d\n", irq); 791 792 ret = sunxi_rsb_hw_init(rsb); 793 if (ret) 794 return ret; 795 796 /* initialize all devices on the bus into RSB mode */ 797 ret = sunxi_rsb_init_device_mode(rsb); 798 if (ret) 799 dev_warn(dev, "Initialize device mode failed: %d\n", ret); 800 801 pm_suspend_ignore_children(dev, true); 802 pm_runtime_set_active(dev); 803 pm_runtime_set_autosuspend_delay(dev, MSEC_PER_SEC); 804 pm_runtime_use_autosuspend(dev); 805 pm_runtime_enable(dev); 806 807 of_rsb_register_devices(rsb); 808 809 return 0; 810 } 811 812 static void sunxi_rsb_remove(struct platform_device *pdev) 813 { 814 struct sunxi_rsb *rsb = platform_get_drvdata(pdev); 815 816 device_for_each_child(rsb->dev, NULL, sunxi_rsb_remove_devices); 817 pm_runtime_disable(&pdev->dev); 818 sunxi_rsb_hw_exit(rsb); 819 } 820 821 static const struct dev_pm_ops sunxi_rsb_dev_pm_ops = { 822 SET_RUNTIME_PM_OPS(sunxi_rsb_runtime_suspend, 823 sunxi_rsb_runtime_resume, NULL) 824 SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(sunxi_rsb_suspend, sunxi_rsb_resume) 825 }; 826 827 static const struct of_device_id sunxi_rsb_of_match_table[] = { 828 { .compatible = "allwinner,sun8i-a23-rsb" }, 829 {} 830 }; 831 MODULE_DEVICE_TABLE(of, sunxi_rsb_of_match_table); 832 833 static struct platform_driver sunxi_rsb_driver = { 834 .probe = sunxi_rsb_probe, 835 .remove = sunxi_rsb_remove, 836 .driver = { 837 .name = RSB_CTRL_NAME, 838 .of_match_table = sunxi_rsb_of_match_table, 839 .pm = &sunxi_rsb_dev_pm_ops, 840 }, 841 }; 842 843 static int __init sunxi_rsb_init(void) 844 { 845 int ret; 846 847 ret = bus_register(&sunxi_rsb_bus); 848 if (ret) { 849 pr_err("failed to register sunxi sunxi_rsb bus: %d\n", ret); 850 return ret; 851 } 852 853 ret = platform_driver_register(&sunxi_rsb_driver); 854 if (ret) { 855 bus_unregister(&sunxi_rsb_bus); 856 return ret; 857 } 858 859 return 0; 860 } 861 module_init(sunxi_rsb_init); 862 863 static void __exit sunxi_rsb_exit(void) 864 { 865 platform_driver_unregister(&sunxi_rsb_driver); 866 bus_unregister(&sunxi_rsb_bus); 867 } 868 module_exit(sunxi_rsb_exit); 869 870 MODULE_AUTHOR("Chen-Yu Tsai <wens@csie.org>"); 871 MODULE_DESCRIPTION("Allwinner sunXi Reduced Serial Bus controller driver"); 872 MODULE_LICENSE("GPL v2"); 873