1 /* 2 * pata_ninja32.c - Ninja32 PATA for new ATA layer 3 * (C) 2007 Red Hat Inc 4 * 5 * Note: The controller like many controllers has shared timings for 6 * PIO and DMA. We thus flip to the DMA timings in dma_start and flip back 7 * in the dma_stop function. Thus we actually don't need a set_dmamode 8 * method as the PIO method is always called and will set the right PIO 9 * timing parameters. 10 * 11 * The Ninja32 Cardbus is not a generic SFF controller. Instead it is 12 * laid out as follows off BAR 0. This is based upon Mark Lord's delkin 13 * driver and the extensive analysis done by the BSD developers, notably 14 * ITOH Yasufumi. 15 * 16 * Base + 0x00 IRQ Status 17 * Base + 0x01 IRQ control 18 * Base + 0x02 Chipset control 19 * Base + 0x03 Unknown 20 * Base + 0x04 VDMA and reset control + wait bits 21 * Base + 0x08 BMIMBA 22 * Base + 0x0C DMA Length 23 * Base + 0x10 Taskfile 24 * Base + 0x18 BMDMA Status ? 25 * Base + 0x1C 26 * Base + 0x1D Bus master control 27 * bit 0 = enable 28 * bit 1 = 0 write/1 read 29 * bit 2 = 1 sgtable 30 * bit 3 = go 31 * bit 4-6 wait bits 32 * bit 7 = done 33 * Base + 0x1E AltStatus 34 * Base + 0x1F timing register 35 */ 36 37 #include <linux/kernel.h> 38 #include <linux/module.h> 39 #include <linux/pci.h> 40 #include <linux/init.h> 41 #include <linux/blkdev.h> 42 #include <linux/delay.h> 43 #include <scsi/scsi_host.h> 44 #include <linux/libata.h> 45 46 #define DRV_NAME "pata_ninja32" 47 #define DRV_VERSION "0.1.5" 48 49 50 /** 51 * ninja32_set_piomode - set initial PIO mode data 52 * @ap: ATA interface 53 * @adev: ATA device 54 * 55 * Called to do the PIO mode setup. Our timing registers are shared 56 * but we want to set the PIO timing by default. 57 */ 58 59 static void ninja32_set_piomode(struct ata_port *ap, struct ata_device *adev) 60 { 61 static u16 pio_timing[5] = { 62 0xd6, 0x85, 0x44, 0x33, 0x13 63 }; 64 iowrite8(pio_timing[adev->pio_mode - XFER_PIO_0], 65 ap->ioaddr.bmdma_addr + 0x1f); 66 ap->private_data = adev; 67 } 68 69 70 static void ninja32_dev_select(struct ata_port *ap, unsigned int device) 71 { 72 struct ata_device *adev = &ap->link.device[device]; 73 if (ap->private_data != adev) { 74 iowrite8(0xd6, ap->ioaddr.bmdma_addr + 0x1f); 75 ata_sff_dev_select(ap, device); 76 ninja32_set_piomode(ap, adev); 77 } 78 } 79 80 static struct scsi_host_template ninja32_sht = { 81 ATA_BMDMA_SHT(DRV_NAME), 82 }; 83 84 static struct ata_port_operations ninja32_port_ops = { 85 .inherits = &ata_bmdma_port_ops, 86 .sff_dev_select = ninja32_dev_select, 87 .cable_detect = ata_cable_40wire, 88 .set_piomode = ninja32_set_piomode, 89 .sff_data_xfer = ata_sff_data_xfer32 90 }; 91 92 static void ninja32_program(void __iomem *base) 93 { 94 iowrite8(0x05, base + 0x01); /* Enable interrupt lines */ 95 iowrite8(0xBE, base + 0x02); /* Burst, ?? setup */ 96 iowrite8(0x01, base + 0x03); /* Unknown */ 97 iowrite8(0x20, base + 0x04); /* WAIT0 */ 98 iowrite8(0x8f, base + 0x05); /* Unknown */ 99 iowrite8(0xa4, base + 0x1c); /* Unknown */ 100 iowrite8(0x83, base + 0x1d); /* BMDMA control: WAIT0 */ 101 } 102 103 static int ninja32_init_one(struct pci_dev *dev, const struct pci_device_id *id) 104 { 105 struct ata_host *host; 106 struct ata_port *ap; 107 void __iomem *base; 108 int rc; 109 110 host = ata_host_alloc(&dev->dev, 1); 111 if (!host) 112 return -ENOMEM; 113 ap = host->ports[0]; 114 115 /* Set up the PCI device */ 116 rc = pcim_enable_device(dev); 117 if (rc) 118 return rc; 119 rc = pcim_iomap_regions(dev, 1 << 0, DRV_NAME); 120 if (rc == -EBUSY) 121 pcim_pin_device(dev); 122 if (rc) 123 return rc; 124 125 host->iomap = pcim_iomap_table(dev); 126 rc = pci_set_dma_mask(dev, ATA_DMA_MASK); 127 if (rc) 128 return rc; 129 rc = pci_set_consistent_dma_mask(dev, ATA_DMA_MASK); 130 if (rc) 131 return rc; 132 pci_set_master(dev); 133 134 /* Set up the register mappings. We use the I/O mapping as only the 135 older chips also have MMIO on BAR 1 */ 136 base = host->iomap[0]; 137 if (!base) 138 return -ENOMEM; 139 ap->ops = &ninja32_port_ops; 140 ap->pio_mask = ATA_PIO4; 141 ap->flags |= ATA_FLAG_SLAVE_POSS; 142 143 ap->ioaddr.cmd_addr = base + 0x10; 144 ap->ioaddr.ctl_addr = base + 0x1E; 145 ap->ioaddr.altstatus_addr = base + 0x1E; 146 ap->ioaddr.bmdma_addr = base; 147 ata_sff_std_ports(&ap->ioaddr); 148 ap->pflags = ATA_PFLAG_PIO32 | ATA_PFLAG_PIO32CHANGE; 149 150 ninja32_program(base); 151 /* FIXME: Should we disable them at remove ? */ 152 return ata_host_activate(host, dev->irq, ata_bmdma_interrupt, 153 IRQF_SHARED, &ninja32_sht); 154 } 155 156 #ifdef CONFIG_PM 157 158 static int ninja32_reinit_one(struct pci_dev *pdev) 159 { 160 struct ata_host *host = dev_get_drvdata(&pdev->dev); 161 int rc; 162 163 rc = ata_pci_device_do_resume(pdev); 164 if (rc) 165 return rc; 166 ninja32_program(host->iomap[0]); 167 ata_host_resume(host); 168 return 0; 169 } 170 #endif 171 172 static const struct pci_device_id ninja32[] = { 173 { 0x10FC, 0x0003, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, 174 { 0x1145, 0x8008, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, 175 { 0x1145, 0xf008, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, 176 { 0x1145, 0xf021, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, 177 { 0x1145, 0xf024, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, 178 { 0x1145, 0xf02C, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, 179 { }, 180 }; 181 182 static struct pci_driver ninja32_pci_driver = { 183 .name = DRV_NAME, 184 .id_table = ninja32, 185 .probe = ninja32_init_one, 186 .remove = ata_pci_remove_one, 187 #ifdef CONFIG_PM 188 .suspend = ata_pci_device_suspend, 189 .resume = ninja32_reinit_one, 190 #endif 191 }; 192 193 module_pci_driver(ninja32_pci_driver); 194 195 MODULE_AUTHOR("Alan Cox"); 196 MODULE_DESCRIPTION("low-level driver for Ninja32 ATA"); 197 MODULE_LICENSE("GPL"); 198 MODULE_DEVICE_TABLE(pci, ninja32); 199 MODULE_VERSION(DRV_VERSION); 200