1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * pata_mpiix.c - Intel MPIIX PATA for new ATA layer 4 * (C) 2005-2006 Red Hat Inc 5 * Alan Cox <alan@lxorguk.ukuu.org.uk> 6 * 7 * The MPIIX is different enough to the PIIX4 and friends that we give it 8 * a separate driver. The old ide/pci code handles this by just not tuning 9 * MPIIX at all. 10 * 11 * The MPIIX also differs in another important way from the majority of PIIX 12 * devices. The chip is a bridge (pardon the pun) between the old world of 13 * ISA IDE and PCI IDE. Although the ATA timings are PCI configured the actual 14 * IDE controller is not decoded in PCI space and the chip does not claim to 15 * be IDE class PCI. This requires slightly non-standard probe logic compared 16 * with PCI IDE and also that we do not disable the device when our driver is 17 * unloaded (as it has many other functions). 18 * 19 * The driver consciously keeps this logic internally to avoid pushing quirky 20 * PATA history into the clean libata layer. 21 * 22 * Thinkpad specific note: If you boot an MPIIX using a thinkpad with a PCMCIA 23 * hard disk present this driver will not detect it. This is not a bug. In this 24 * configuration the secondary port of the MPIIX is disabled and the addresses 25 * are decoded by the PCMCIA bridge and therefore are for a generic IDE driver 26 * to operate. 27 */ 28 29 #include <linux/kernel.h> 30 #include <linux/module.h> 31 #include <linux/pci.h> 32 #include <linux/blkdev.h> 33 #include <linux/delay.h> 34 #include <scsi/scsi_host.h> 35 #include <linux/libata.h> 36 37 #define DRV_NAME "pata_mpiix" 38 #define DRV_VERSION "0.7.7" 39 40 enum { 41 IDETIM = 0x6C, /* IDE control register */ 42 IORDY = (1 << 1), 43 PPE = (1 << 2), 44 FTIM = (1 << 0), 45 ENABLED = (1 << 15), 46 SECONDARY = (1 << 14) 47 }; 48 49 static int mpiix_pre_reset(struct ata_link *link, unsigned long deadline) 50 { 51 struct ata_port *ap = link->ap; 52 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 53 static const struct pci_bits mpiix_enable_bits = { 0x6D, 1, 0x80, 0x80 }; 54 55 if (!pci_test_config_bits(pdev, &mpiix_enable_bits)) 56 return -ENOENT; 57 58 return ata_sff_prereset(link, deadline); 59 } 60 61 /** 62 * mpiix_set_piomode - set initial PIO mode data 63 * @ap: ATA interface 64 * @adev: ATA device 65 * 66 * Called to do the PIO mode setup. The MPIIX allows us to program the 67 * IORDY sample point (2-5 clocks), recovery (1-4 clocks) and whether 68 * prefetching or IORDY are used. 69 * 70 * This would get very ugly because we can only program timing for one 71 * device at a time, the other gets PIO0. Fortunately libata calls 72 * our qc_issue command before a command is issued so we can flip the 73 * timings back and forth to reduce the pain. 74 */ 75 76 static void mpiix_set_piomode(struct ata_port *ap, struct ata_device *adev) 77 { 78 int control = 0; 79 int pio = adev->pio_mode - XFER_PIO_0; 80 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 81 u16 idetim; 82 static const /* ISP RTC */ 83 u8 timings[][2] = { { 0, 0 }, 84 { 0, 0 }, 85 { 1, 0 }, 86 { 2, 1 }, 87 { 2, 3 }, }; 88 89 pci_read_config_word(pdev, IDETIM, &idetim); 90 91 /* Mask the IORDY/TIME/PPE for this device */ 92 if (adev->class == ATA_DEV_ATA) 93 control |= PPE; /* Enable prefetch/posting for disk */ 94 if (ata_pio_need_iordy(adev)) 95 control |= IORDY; 96 if (pio > 1) 97 control |= FTIM; /* This drive is on the fast timing bank */ 98 99 /* Mask out timing and clear both TIME bank selects */ 100 idetim &= 0xCCEE; 101 idetim &= ~(0x07 << (4 * adev->devno)); 102 idetim |= control << (4 * adev->devno); 103 104 idetim |= (timings[pio][0] << 12) | (timings[pio][1] << 8); 105 pci_write_config_word(pdev, IDETIM, idetim); 106 107 /* We use ap->private_data as a pointer to the device currently 108 loaded for timing */ 109 ap->private_data = adev; 110 } 111 112 /** 113 * mpiix_qc_issue - command issue 114 * @qc: command pending 115 * 116 * Called when the libata layer is about to issue a command. We wrap 117 * this interface so that we can load the correct ATA timings if 118 * necessary. Our logic also clears TIME0/TIME1 for the other device so 119 * that, even if we get this wrong, cycles to the other device will 120 * be made PIO0. 121 */ 122 123 static unsigned int mpiix_qc_issue(struct ata_queued_cmd *qc) 124 { 125 struct ata_port *ap = qc->ap; 126 struct ata_device *adev = qc->dev; 127 128 /* If modes have been configured and the channel data is not loaded 129 then load it. We have to check if pio_mode is set as the core code 130 does not set adev->pio_mode to XFER_PIO_0 while probing as would be 131 logical */ 132 133 if (adev->pio_mode && adev != ap->private_data) 134 mpiix_set_piomode(ap, adev); 135 136 return ata_sff_qc_issue(qc); 137 } 138 139 static struct scsi_host_template mpiix_sht = { 140 ATA_PIO_SHT(DRV_NAME), 141 }; 142 143 static struct ata_port_operations mpiix_port_ops = { 144 .inherits = &ata_sff_port_ops, 145 .qc_issue = mpiix_qc_issue, 146 .cable_detect = ata_cable_40wire, 147 .set_piomode = mpiix_set_piomode, 148 .prereset = mpiix_pre_reset, 149 .sff_data_xfer = ata_sff_data_xfer32, 150 }; 151 152 static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id) 153 { 154 /* Single threaded by the PCI probe logic */ 155 struct ata_host *host; 156 struct ata_port *ap; 157 void __iomem *cmd_addr, *ctl_addr; 158 u16 idetim; 159 int cmd, ctl, irq; 160 161 ata_print_version_once(&dev->dev, DRV_VERSION); 162 163 host = ata_host_alloc(&dev->dev, 1); 164 if (!host) 165 return -ENOMEM; 166 ap = host->ports[0]; 167 168 /* MPIIX has many functions which can be turned on or off according 169 to other devices present. Make sure IDE is enabled before we try 170 and use it */ 171 172 pci_read_config_word(dev, IDETIM, &idetim); 173 if (!(idetim & ENABLED)) 174 return -ENODEV; 175 176 /* See if it's primary or secondary channel... */ 177 if (!(idetim & SECONDARY)) { 178 cmd = 0x1F0; 179 ctl = 0x3F6; 180 irq = 14; 181 } else { 182 cmd = 0x170; 183 ctl = 0x376; 184 irq = 15; 185 } 186 187 cmd_addr = devm_ioport_map(&dev->dev, cmd, 8); 188 ctl_addr = devm_ioport_map(&dev->dev, ctl, 1); 189 if (!cmd_addr || !ctl_addr) 190 return -ENOMEM; 191 192 ata_port_desc(ap, "cmd 0x%x ctl 0x%x", cmd, ctl); 193 194 /* We do our own plumbing to avoid leaking special cases for whacko 195 ancient hardware into the core code. There are two issues to 196 worry about. #1 The chip is a bridge so if in legacy mode and 197 without BARs set fools the setup. #2 If you pci_disable_device 198 the MPIIX your box goes castors up */ 199 200 ap->ops = &mpiix_port_ops; 201 ap->pio_mask = ATA_PIO4; 202 ap->flags |= ATA_FLAG_SLAVE_POSS; 203 204 ap->ioaddr.cmd_addr = cmd_addr; 205 ap->ioaddr.ctl_addr = ctl_addr; 206 ap->ioaddr.altstatus_addr = ctl_addr; 207 208 /* Let libata fill in the port details */ 209 ata_sff_std_ports(&ap->ioaddr); 210 211 /* activate host */ 212 return ata_host_activate(host, irq, ata_sff_interrupt, IRQF_SHARED, 213 &mpiix_sht); 214 } 215 216 static const struct pci_device_id mpiix[] = { 217 { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX), }, 218 219 { }, 220 }; 221 222 static struct pci_driver mpiix_pci_driver = { 223 .name = DRV_NAME, 224 .id_table = mpiix, 225 .probe = mpiix_init_one, 226 .remove = ata_pci_remove_one, 227 #ifdef CONFIG_PM_SLEEP 228 .suspend = ata_pci_device_suspend, 229 .resume = ata_pci_device_resume, 230 #endif 231 }; 232 233 module_pci_driver(mpiix_pci_driver); 234 235 MODULE_AUTHOR("Alan Cox"); 236 MODULE_DESCRIPTION("low-level driver for Intel MPIIX"); 237 MODULE_LICENSE("GPL"); 238 MODULE_DEVICE_TABLE(pci, mpiix); 239 MODULE_VERSION(DRV_VERSION); 240