1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * pata_it8213.c - iTE Tech. Inc. IT8213 PATA driver 4 * 5 * The IT8213 is a very Intel ICH like device for timing purposes, having 6 * a similar register layout and the same split clock arrangement. Cable 7 * detection is different, and it does not have slave channels or all the 8 * clutter of later ICH/SATA setups. 9 */ 10 11 #include <linux/kernel.h> 12 #include <linux/module.h> 13 #include <linux/pci.h> 14 #include <linux/blkdev.h> 15 #include <linux/delay.h> 16 #include <linux/device.h> 17 #include <scsi/scsi_host.h> 18 #include <linux/libata.h> 19 #include <linux/ata.h> 20 21 #define DRV_NAME "pata_it8213" 22 #define DRV_VERSION "0.0.3" 23 24 /** 25 * it8213_pre_reset - probe begin 26 * @link: link 27 * @deadline: deadline jiffies for the operation 28 * 29 * Filter out ports by the enable bits before doing the normal reset 30 * and probe. 31 */ 32 33 static int it8213_pre_reset(struct ata_link *link, unsigned long deadline) 34 { 35 static const struct pci_bits it8213_enable_bits[] = { 36 { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */ 37 }; 38 struct ata_port *ap = link->ap; 39 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 40 if (!pci_test_config_bits(pdev, &it8213_enable_bits[ap->port_no])) 41 return -ENOENT; 42 43 return ata_sff_prereset(link, deadline); 44 } 45 46 /** 47 * it8213_cable_detect - check for 40/80 pin 48 * @ap: Port 49 * 50 * Perform cable detection for the 8213 ATA interface. This is 51 * different to the PIIX arrangement 52 */ 53 54 static int it8213_cable_detect(struct ata_port *ap) 55 { 56 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 57 u8 tmp; 58 pci_read_config_byte(pdev, 0x42, &tmp); 59 if (tmp & 2) /* The initial docs are incorrect */ 60 return ATA_CBL_PATA40; 61 return ATA_CBL_PATA80; 62 } 63 64 /** 65 * it8213_set_piomode - Initialize host controller PATA PIO timings 66 * @ap: Port whose timings we are configuring 67 * @adev: Device whose timings we are configuring 68 * 69 * Set PIO mode for device, in host controller PCI config space. 70 * 71 * LOCKING: 72 * None (inherited from caller). 73 */ 74 75 static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev) 76 { 77 unsigned int pio = adev->pio_mode - XFER_PIO_0; 78 struct pci_dev *dev = to_pci_dev(ap->host->dev); 79 unsigned int master_port = ap->port_no ? 0x42 : 0x40; 80 u16 master_data; 81 int control = 0; 82 83 /* 84 * See Intel Document 298600-004 for the timing programing rules 85 * for PIIX/ICH. The 8213 is a clone so very similar 86 */ 87 88 static const /* ISP RTC */ 89 u8 timings[][2] = { { 0, 0 }, 90 { 0, 0 }, 91 { 1, 0 }, 92 { 2, 1 }, 93 { 2, 3 }, }; 94 95 if (pio > 1) 96 control |= 1; /* TIME */ 97 if (ata_pio_need_iordy(adev)) /* PIO 3/4 require IORDY */ 98 control |= 2; /* IE */ 99 /* Bit 2 is set for ATAPI on the IT8213 - reverse of ICH/PIIX */ 100 if (adev->class != ATA_DEV_ATA) 101 control |= 4; /* PPE */ 102 103 pci_read_config_word(dev, master_port, &master_data); 104 105 /* Set PPE, IE, and TIME as appropriate */ 106 if (adev->devno == 0) { 107 master_data &= 0xCCF0; 108 master_data |= control; 109 master_data |= (timings[pio][0] << 12) | 110 (timings[pio][1] << 8); 111 } else { 112 u8 slave_data; 113 114 master_data &= 0xFF0F; 115 master_data |= (control << 4); 116 117 /* Slave timing in separate register */ 118 pci_read_config_byte(dev, 0x44, &slave_data); 119 slave_data &= 0xF0; 120 slave_data |= (timings[pio][0] << 2) | timings[pio][1]; 121 pci_write_config_byte(dev, 0x44, slave_data); 122 } 123 124 master_data |= 0x4000; /* Ensure SITRE is set */ 125 pci_write_config_word(dev, master_port, master_data); 126 } 127 128 /** 129 * it8213_set_dmamode - Initialize host controller PATA DMA timings 130 * @ap: Port whose timings we are configuring 131 * @adev: Device to program 132 * 133 * Set UDMA/MWDMA mode for device, in host controller PCI config space. 134 * This device is basically an ICH alike. 135 * 136 * LOCKING: 137 * None (inherited from caller). 138 */ 139 140 static void it8213_set_dmamode (struct ata_port *ap, struct ata_device *adev) 141 { 142 struct pci_dev *dev = to_pci_dev(ap->host->dev); 143 u16 master_data; 144 u8 speed = adev->dma_mode; 145 int devid = adev->devno; 146 u8 udma_enable; 147 148 static const /* ISP RTC */ 149 u8 timings[][2] = { { 0, 0 }, 150 { 0, 0 }, 151 { 1, 0 }, 152 { 2, 1 }, 153 { 2, 3 }, }; 154 155 pci_read_config_word(dev, 0x40, &master_data); 156 pci_read_config_byte(dev, 0x48, &udma_enable); 157 158 if (speed >= XFER_UDMA_0) { 159 unsigned int udma = adev->dma_mode - XFER_UDMA_0; 160 u16 udma_timing; 161 u16 ideconf; 162 int u_clock, u_speed; 163 164 /* Clocks follow the PIIX style */ 165 u_speed = min(2 - (udma & 1), udma); 166 if (udma > 4) 167 u_clock = 0x1000; /* 100Mhz */ 168 else if (udma > 2) 169 u_clock = 1; /* 66Mhz */ 170 else 171 u_clock = 0; /* 33Mhz */ 172 173 udma_enable |= (1 << devid); 174 175 /* Load the UDMA cycle time */ 176 pci_read_config_word(dev, 0x4A, &udma_timing); 177 udma_timing &= ~(3 << (4 * devid)); 178 udma_timing |= u_speed << (4 * devid); 179 pci_write_config_word(dev, 0x4A, udma_timing); 180 181 /* Load the clock selection */ 182 pci_read_config_word(dev, 0x54, &ideconf); 183 ideconf &= ~(0x1001 << devid); 184 ideconf |= u_clock << devid; 185 pci_write_config_word(dev, 0x54, ideconf); 186 } else { 187 /* 188 * MWDMA is driven by the PIO timings. We must also enable 189 * IORDY unconditionally along with TIME1. PPE has already 190 * been set when the PIO timing was set. 191 */ 192 unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; 193 unsigned int control; 194 u8 slave_data; 195 static const unsigned int needed_pio[3] = { 196 XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 197 }; 198 int pio = needed_pio[mwdma] - XFER_PIO_0; 199 200 control = 3; /* IORDY|TIME1 */ 201 202 /* If the drive MWDMA is faster than it can do PIO then 203 we must force PIO into PIO0 */ 204 205 if (adev->pio_mode < needed_pio[mwdma]) 206 /* Enable DMA timing only */ 207 control |= 8; /* PIO cycles in PIO0 */ 208 209 if (devid) { /* Slave */ 210 master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */ 211 master_data |= control << 4; 212 pci_read_config_byte(dev, 0x44, &slave_data); 213 slave_data &= 0xF0; 214 /* Load the matching timing */ 215 slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0); 216 pci_write_config_byte(dev, 0x44, slave_data); 217 } else { /* Master */ 218 master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY 219 and master timing bits */ 220 master_data |= control; 221 master_data |= 222 (timings[pio][0] << 12) | 223 (timings[pio][1] << 8); 224 } 225 udma_enable &= ~(1 << devid); 226 pci_write_config_word(dev, 0x40, master_data); 227 } 228 pci_write_config_byte(dev, 0x48, udma_enable); 229 } 230 231 static const struct scsi_host_template it8213_sht = { 232 ATA_BMDMA_SHT(DRV_NAME), 233 }; 234 235 236 static struct ata_port_operations it8213_ops = { 237 .inherits = &ata_bmdma_port_ops, 238 .cable_detect = it8213_cable_detect, 239 .set_piomode = it8213_set_piomode, 240 .set_dmamode = it8213_set_dmamode, 241 .prereset = it8213_pre_reset, 242 }; 243 244 245 /** 246 * it8213_init_one - Register 8213 ATA PCI device with kernel services 247 * @pdev: PCI device to register 248 * @ent: Entry in it8213_pci_tbl matching with @pdev 249 * 250 * Called from kernel PCI layer. 251 * 252 * LOCKING: 253 * Inherited from PCI layer (may sleep). 254 * 255 * RETURNS: 256 * Zero on success, or -ERRNO value. 257 */ 258 259 static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) 260 { 261 static const struct ata_port_info info = { 262 .flags = ATA_FLAG_SLAVE_POSS, 263 .pio_mask = ATA_PIO4, 264 .mwdma_mask = ATA_MWDMA12_ONLY, 265 .udma_mask = ATA_UDMA6, 266 .port_ops = &it8213_ops, 267 }; 268 /* Current IT8213 stuff is single port */ 269 const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info }; 270 271 ata_print_version_once(&pdev->dev, DRV_VERSION); 272 273 return ata_pci_bmdma_init_one(pdev, ppi, &it8213_sht, NULL, 0); 274 } 275 276 static const struct pci_device_id it8213_pci_tbl[] = { 277 { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8213), }, 278 279 { } /* terminate list */ 280 }; 281 282 static struct pci_driver it8213_pci_driver = { 283 .name = DRV_NAME, 284 .id_table = it8213_pci_tbl, 285 .probe = it8213_init_one, 286 .remove = ata_pci_remove_one, 287 #ifdef CONFIG_PM_SLEEP 288 .suspend = ata_pci_device_suspend, 289 .resume = ata_pci_device_resume, 290 #endif 291 }; 292 293 module_pci_driver(it8213_pci_driver); 294 295 MODULE_AUTHOR("Alan Cox"); 296 MODULE_DESCRIPTION("SCSI low-level driver for the ITE 8213"); 297 MODULE_LICENSE("GPL"); 298 MODULE_DEVICE_TABLE(pci, it8213_pci_tbl); 299 MODULE_VERSION(DRV_VERSION); 300