1 /* 2 * pata-cs5530.c - CS5530 PATA for new ATA layer 3 * (C) 2005 Red Hat Inc 4 * 5 * based upon cs5530.c by Mark Lord. 6 * 7 * This program is free software; you can redistribute it and/or modify 8 * it under the terms of the GNU General Public License version 2 as 9 * published by the Free Software Foundation. 10 * 11 * This program is distributed in the hope that it will be useful, 12 * but WITHOUT ANY WARRANTY; without even the implied warranty of 13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 14 * GNU General Public License for more details. 15 * 16 * You should have received a copy of the GNU General Public License 17 * along with this program; if not, write to the Free Software 18 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA 19 * 20 * Loosely based on the piix & svwks drivers. 21 * 22 * Documentation: 23 * Available from AMD web site. 24 */ 25 26 #include <linux/kernel.h> 27 #include <linux/module.h> 28 #include <linux/pci.h> 29 #include <linux/init.h> 30 #include <linux/blkdev.h> 31 #include <linux/delay.h> 32 #include <scsi/scsi_host.h> 33 #include <linux/libata.h> 34 #include <linux/dmi.h> 35 36 #define DRV_NAME "pata_cs5530" 37 #define DRV_VERSION "0.7.4" 38 39 static void __iomem *cs5530_port_base(struct ata_port *ap) 40 { 41 unsigned long bmdma = (unsigned long)ap->ioaddr.bmdma_addr; 42 43 return (void __iomem *)((bmdma & ~0x0F) + 0x20 + 0x10 * ap->port_no); 44 } 45 46 /** 47 * cs5530_set_piomode - PIO setup 48 * @ap: ATA interface 49 * @adev: device on the interface 50 * 51 * Set our PIO requirements. This is fairly simple on the CS5530 52 * chips. 53 */ 54 55 static void cs5530_set_piomode(struct ata_port *ap, struct ata_device *adev) 56 { 57 static const unsigned int cs5530_pio_timings[2][5] = { 58 {0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010}, 59 {0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010} 60 }; 61 void __iomem *base = cs5530_port_base(ap); 62 u32 tuning; 63 int format; 64 65 /* Find out which table to use */ 66 tuning = ioread32(base + 0x04); 67 format = (tuning & 0x80000000UL) ? 1 : 0; 68 69 /* Now load the right timing register */ 70 if (adev->devno) 71 base += 0x08; 72 73 iowrite32(cs5530_pio_timings[format][adev->pio_mode - XFER_PIO_0], base); 74 } 75 76 /** 77 * cs5530_set_dmamode - DMA timing setup 78 * @ap: ATA interface 79 * @adev: Device being configured 80 * 81 * We cannot mix MWDMA and UDMA without reloading timings each switch 82 * master to slave. We track the last DMA setup in order to minimise 83 * reloads. 84 */ 85 86 static void cs5530_set_dmamode(struct ata_port *ap, struct ata_device *adev) 87 { 88 void __iomem *base = cs5530_port_base(ap); 89 u32 tuning, timing = 0; 90 u8 reg; 91 92 /* Find out which table to use */ 93 tuning = ioread32(base + 0x04); 94 95 switch(adev->dma_mode) { 96 case XFER_UDMA_0: 97 timing = 0x00921250;break; 98 case XFER_UDMA_1: 99 timing = 0x00911140;break; 100 case XFER_UDMA_2: 101 timing = 0x00911030;break; 102 case XFER_MW_DMA_0: 103 timing = 0x00077771;break; 104 case XFER_MW_DMA_1: 105 timing = 0x00012121;break; 106 case XFER_MW_DMA_2: 107 timing = 0x00002020;break; 108 default: 109 BUG(); 110 } 111 /* Merge in the PIO format bit */ 112 timing |= (tuning & 0x80000000UL); 113 if (adev->devno == 0) /* Master */ 114 iowrite32(timing, base + 0x04); 115 else { 116 if (timing & 0x00100000) 117 tuning |= 0x00100000; /* UDMA for both */ 118 else 119 tuning &= ~0x00100000; /* MWDMA for both */ 120 iowrite32(tuning, base + 0x04); 121 iowrite32(timing, base + 0x0C); 122 } 123 124 /* Set the DMA capable bit in the BMDMA area */ 125 reg = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); 126 reg |= (1 << (5 + adev->devno)); 127 iowrite8(reg, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); 128 129 /* Remember the last DMA setup we did */ 130 131 ap->private_data = adev; 132 } 133 134 /** 135 * cs5530_qc_issue - command issue 136 * @qc: command pending 137 * 138 * Called when the libata layer is about to issue a command. We wrap 139 * this interface so that we can load the correct ATA timings if 140 * necessary. Specifically we have a problem that there is only 141 * one MWDMA/UDMA bit. 142 */ 143 144 static unsigned int cs5530_qc_issue(struct ata_queued_cmd *qc) 145 { 146 struct ata_port *ap = qc->ap; 147 struct ata_device *adev = qc->dev; 148 struct ata_device *prev = ap->private_data; 149 150 /* See if the DMA settings could be wrong */ 151 if (ata_dma_enabled(adev) && adev != prev && prev != NULL) { 152 /* Maybe, but do the channels match MWDMA/UDMA ? */ 153 if ((ata_using_udma(adev) && !ata_using_udma(prev)) || 154 (ata_using_udma(prev) && !ata_using_udma(adev))) 155 /* Switch the mode bits */ 156 cs5530_set_dmamode(ap, adev); 157 } 158 159 return ata_bmdma_qc_issue(qc); 160 } 161 162 static struct scsi_host_template cs5530_sht = { 163 ATA_BMDMA_SHT(DRV_NAME), 164 .sg_tablesize = LIBATA_DUMB_MAX_PRD, 165 }; 166 167 static struct ata_port_operations cs5530_port_ops = { 168 .inherits = &ata_bmdma_port_ops, 169 170 .qc_prep = ata_bmdma_dumb_qc_prep, 171 .qc_issue = cs5530_qc_issue, 172 173 .cable_detect = ata_cable_40wire, 174 .set_piomode = cs5530_set_piomode, 175 .set_dmamode = cs5530_set_dmamode, 176 }; 177 178 static const struct dmi_system_id palmax_dmi_table[] = { 179 { 180 .ident = "Palmax PD1100", 181 .matches = { 182 DMI_MATCH(DMI_SYS_VENDOR, "Cyrix"), 183 DMI_MATCH(DMI_PRODUCT_NAME, "Caddis"), 184 }, 185 }, 186 { } 187 }; 188 189 static int cs5530_is_palmax(void) 190 { 191 if (dmi_check_system(palmax_dmi_table)) { 192 printk(KERN_INFO "Palmax PD1100: Disabling DMA on docking port.\n"); 193 return 1; 194 } 195 return 0; 196 } 197 198 199 /** 200 * cs5530_init_chip - Chipset init 201 * 202 * Perform the chip initialisation work that is shared between both 203 * setup and resume paths 204 */ 205 206 static int cs5530_init_chip(void) 207 { 208 struct pci_dev *master_0 = NULL, *cs5530_0 = NULL, *dev = NULL; 209 210 while ((dev = pci_get_device(PCI_VENDOR_ID_CYRIX, PCI_ANY_ID, dev)) != NULL) { 211 switch (dev->device) { 212 case PCI_DEVICE_ID_CYRIX_PCI_MASTER: 213 master_0 = pci_dev_get(dev); 214 break; 215 case PCI_DEVICE_ID_CYRIX_5530_LEGACY: 216 cs5530_0 = pci_dev_get(dev); 217 break; 218 } 219 } 220 if (!master_0) { 221 printk(KERN_ERR DRV_NAME ": unable to locate PCI MASTER function\n"); 222 goto fail_put; 223 } 224 if (!cs5530_0) { 225 printk(KERN_ERR DRV_NAME ": unable to locate CS5530 LEGACY function\n"); 226 goto fail_put; 227 } 228 229 pci_set_master(cs5530_0); 230 pci_try_set_mwi(cs5530_0); 231 232 /* 233 * Set PCI CacheLineSize to 16-bytes: 234 * --> Write 0x04 into 8-bit PCI CACHELINESIZE reg of function 0 of the cs5530 235 * 236 * Note: This value is constant because the 5530 is only a Geode companion 237 */ 238 239 pci_write_config_byte(cs5530_0, PCI_CACHE_LINE_SIZE, 0x04); 240 241 /* 242 * Disable trapping of UDMA register accesses (Win98 hack): 243 * --> Write 0x5006 into 16-bit reg at offset 0xd0 of function 0 of the cs5530 244 */ 245 246 pci_write_config_word(cs5530_0, 0xd0, 0x5006); 247 248 /* 249 * Bit-1 at 0x40 enables MemoryWriteAndInvalidate on internal X-bus: 250 * The other settings are what is necessary to get the register 251 * into a sane state for IDE DMA operation. 252 */ 253 254 pci_write_config_byte(master_0, 0x40, 0x1e); 255 256 /* 257 * Set max PCI burst size (16-bytes seems to work best): 258 * 16bytes: set bit-1 at 0x41 (reg value of 0x16) 259 * all others: clear bit-1 at 0x41, and do: 260 * 128bytes: OR 0x00 at 0x41 261 * 256bytes: OR 0x04 at 0x41 262 * 512bytes: OR 0x08 at 0x41 263 * 1024bytes: OR 0x0c at 0x41 264 */ 265 266 pci_write_config_byte(master_0, 0x41, 0x14); 267 268 /* 269 * These settings are necessary to get the chip 270 * into a sane state for IDE DMA operation. 271 */ 272 273 pci_write_config_byte(master_0, 0x42, 0x00); 274 pci_write_config_byte(master_0, 0x43, 0xc1); 275 276 pci_dev_put(master_0); 277 pci_dev_put(cs5530_0); 278 return 0; 279 fail_put: 280 if (master_0) 281 pci_dev_put(master_0); 282 if (cs5530_0) 283 pci_dev_put(cs5530_0); 284 return -ENODEV; 285 } 286 287 /** 288 * cs5530_init_one - Initialise a CS5530 289 * @dev: PCI device 290 * @id: Entry in match table 291 * 292 * Install a driver for the newly found CS5530 companion chip. Most of 293 * this is just housekeeping. We have to set the chip up correctly and 294 * turn off various bits of emulation magic. 295 */ 296 297 static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id) 298 { 299 static const struct ata_port_info info = { 300 .flags = ATA_FLAG_SLAVE_POSS, 301 .pio_mask = ATA_PIO4, 302 .mwdma_mask = ATA_MWDMA2, 303 .udma_mask = ATA_UDMA2, 304 .port_ops = &cs5530_port_ops 305 }; 306 /* The docking connector doesn't do UDMA, and it seems not MWDMA */ 307 static const struct ata_port_info info_palmax_secondary = { 308 .flags = ATA_FLAG_SLAVE_POSS, 309 .pio_mask = ATA_PIO4, 310 .port_ops = &cs5530_port_ops 311 }; 312 const struct ata_port_info *ppi[] = { &info, NULL }; 313 int rc; 314 315 rc = pcim_enable_device(pdev); 316 if (rc) 317 return rc; 318 319 /* Chip initialisation */ 320 if (cs5530_init_chip()) 321 return -ENODEV; 322 323 if (cs5530_is_palmax()) 324 ppi[1] = &info_palmax_secondary; 325 326 /* Now kick off ATA set up */ 327 return ata_pci_bmdma_init_one(pdev, ppi, &cs5530_sht, NULL, 0); 328 } 329 330 #ifdef CONFIG_PM 331 static int cs5530_reinit_one(struct pci_dev *pdev) 332 { 333 struct ata_host *host = dev_get_drvdata(&pdev->dev); 334 int rc; 335 336 rc = ata_pci_device_do_resume(pdev); 337 if (rc) 338 return rc; 339 340 /* If we fail on resume we are doomed */ 341 if (cs5530_init_chip()) 342 return -EIO; 343 344 ata_host_resume(host); 345 return 0; 346 } 347 #endif /* CONFIG_PM */ 348 349 static const struct pci_device_id cs5530[] = { 350 { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), }, 351 352 { }, 353 }; 354 355 static struct pci_driver cs5530_pci_driver = { 356 .name = DRV_NAME, 357 .id_table = cs5530, 358 .probe = cs5530_init_one, 359 .remove = ata_pci_remove_one, 360 #ifdef CONFIG_PM 361 .suspend = ata_pci_device_suspend, 362 .resume = cs5530_reinit_one, 363 #endif 364 }; 365 366 static int __init cs5530_init(void) 367 { 368 return pci_register_driver(&cs5530_pci_driver); 369 } 370 371 static void __exit cs5530_exit(void) 372 { 373 pci_unregister_driver(&cs5530_pci_driver); 374 } 375 376 MODULE_AUTHOR("Alan Cox"); 377 MODULE_DESCRIPTION("low-level driver for the Cyrix/NS/AMD 5530"); 378 MODULE_LICENSE("GPL"); 379 MODULE_DEVICE_TABLE(pci, cs5530); 380 MODULE_VERSION(DRV_VERSION); 381 382 module_init(cs5530_init); 383 module_exit(cs5530_exit); 384