1 /* 2 * pata_atiixp.c - ATI PATA for new ATA layer 3 * (C) 2005 Red Hat Inc 4 * (C) 2009-2010 Bartlomiej Zolnierkiewicz 5 * 6 * Based on 7 * 8 * linux/drivers/ide/pci/atiixp.c Version 0.01-bart2 Feb. 26, 2004 9 * 10 * Copyright (C) 2003 ATI Inc. <hyu@ati.com> 11 * Copyright (C) 2004 Bartlomiej Zolnierkiewicz 12 * 13 */ 14 15 #include <linux/kernel.h> 16 #include <linux/module.h> 17 #include <linux/pci.h> 18 #include <linux/blkdev.h> 19 #include <linux/delay.h> 20 #include <scsi/scsi_host.h> 21 #include <linux/libata.h> 22 #include <linux/dmi.h> 23 24 #define DRV_NAME "pata_atiixp" 25 #define DRV_VERSION "0.4.6" 26 27 enum { 28 ATIIXP_IDE_PIO_TIMING = 0x40, 29 ATIIXP_IDE_MWDMA_TIMING = 0x44, 30 ATIIXP_IDE_PIO_CONTROL = 0x48, 31 ATIIXP_IDE_PIO_MODE = 0x4a, 32 ATIIXP_IDE_UDMA_CONTROL = 0x54, 33 ATIIXP_IDE_UDMA_MODE = 0x56 34 }; 35 36 static const struct dmi_system_id attixp_cable_override_dmi_table[] = { 37 { 38 /* Board has onboard PATA<->SATA converters */ 39 .ident = "MSI E350DM-E33", 40 .matches = { 41 DMI_MATCH(DMI_BOARD_VENDOR, "MSI"), 42 DMI_MATCH(DMI_BOARD_NAME, "E350DM-E33(MS-7720)"), 43 }, 44 }, 45 { } 46 }; 47 48 static int atiixp_cable_detect(struct ata_port *ap) 49 { 50 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 51 u8 udma; 52 53 if (dmi_check_system(attixp_cable_override_dmi_table)) 54 return ATA_CBL_PATA40_SHORT; 55 56 /* Hack from drivers/ide/pci. Really we want to know how to do the 57 raw detection not play follow the bios mode guess */ 58 pci_read_config_byte(pdev, ATIIXP_IDE_UDMA_MODE + ap->port_no, &udma); 59 if ((udma & 0x07) >= 0x04 || (udma & 0x70) >= 0x40) 60 return ATA_CBL_PATA80; 61 return ATA_CBL_PATA40; 62 } 63 64 static DEFINE_SPINLOCK(atiixp_lock); 65 66 /** 67 * atiixp_prereset - perform reset handling 68 * @link: ATA link 69 * @deadline: deadline jiffies for the operation 70 * 71 * Reset sequence checking enable bits to see which ports are 72 * active. 73 */ 74 75 static int atiixp_prereset(struct ata_link *link, unsigned long deadline) 76 { 77 static const struct pci_bits atiixp_enable_bits[] = { 78 { 0x48, 1, 0x01, 0x00 }, 79 { 0x48, 1, 0x08, 0x00 } 80 }; 81 82 struct ata_port *ap = link->ap; 83 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 84 85 if (!pci_test_config_bits(pdev, &atiixp_enable_bits[ap->port_no])) 86 return -ENOENT; 87 88 return ata_sff_prereset(link, deadline); 89 } 90 91 /** 92 * atiixp_set_pio_timing - set initial PIO mode data 93 * @ap: ATA interface 94 * @adev: ATA device 95 * 96 * Called by both the pio and dma setup functions to set the controller 97 * timings for PIO transfers. We must load both the mode number and 98 * timing values into the controller. 99 */ 100 101 static void atiixp_set_pio_timing(struct ata_port *ap, struct ata_device *adev, int pio) 102 { 103 static u8 pio_timings[5] = { 0x5D, 0x47, 0x34, 0x22, 0x20 }; 104 105 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 106 int dn = 2 * ap->port_no + adev->devno; 107 int timing_shift = (16 * ap->port_no) + 8 * (adev->devno ^ 1); 108 u32 pio_timing_data; 109 u16 pio_mode_data; 110 111 pci_read_config_word(pdev, ATIIXP_IDE_PIO_MODE, &pio_mode_data); 112 pio_mode_data &= ~(0x7 << (4 * dn)); 113 pio_mode_data |= pio << (4 * dn); 114 pci_write_config_word(pdev, ATIIXP_IDE_PIO_MODE, pio_mode_data); 115 116 pci_read_config_dword(pdev, ATIIXP_IDE_PIO_TIMING, &pio_timing_data); 117 pio_timing_data &= ~(0xFF << timing_shift); 118 pio_timing_data |= (pio_timings[pio] << timing_shift); 119 pci_write_config_dword(pdev, ATIIXP_IDE_PIO_TIMING, pio_timing_data); 120 } 121 122 /** 123 * atiixp_set_piomode - set initial PIO mode data 124 * @ap: ATA interface 125 * @adev: ATA device 126 * 127 * Called to do the PIO mode setup. We use a shared helper for this 128 * as the DMA setup must also adjust the PIO timing information. 129 */ 130 131 static void atiixp_set_piomode(struct ata_port *ap, struct ata_device *adev) 132 { 133 unsigned long flags; 134 spin_lock_irqsave(&atiixp_lock, flags); 135 atiixp_set_pio_timing(ap, adev, adev->pio_mode - XFER_PIO_0); 136 spin_unlock_irqrestore(&atiixp_lock, flags); 137 } 138 139 /** 140 * atiixp_set_dmamode - set initial DMA mode data 141 * @ap: ATA interface 142 * @adev: ATA device 143 * 144 * Called to do the DMA mode setup. We use timing tables for most 145 * modes but must tune an appropriate PIO mode to match. 146 */ 147 148 static void atiixp_set_dmamode(struct ata_port *ap, struct ata_device *adev) 149 { 150 static u8 mwdma_timings[5] = { 0x77, 0x21, 0x20 }; 151 152 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 153 int dma = adev->dma_mode; 154 int dn = 2 * ap->port_no + adev->devno; 155 int wanted_pio; 156 unsigned long flags; 157 158 spin_lock_irqsave(&atiixp_lock, flags); 159 160 if (adev->dma_mode >= XFER_UDMA_0) { 161 u16 udma_mode_data; 162 163 dma -= XFER_UDMA_0; 164 165 pci_read_config_word(pdev, ATIIXP_IDE_UDMA_MODE, &udma_mode_data); 166 udma_mode_data &= ~(0x7 << (4 * dn)); 167 udma_mode_data |= dma << (4 * dn); 168 pci_write_config_word(pdev, ATIIXP_IDE_UDMA_MODE, udma_mode_data); 169 } else { 170 int timing_shift = (16 * ap->port_no) + 8 * (adev->devno ^ 1); 171 u32 mwdma_timing_data; 172 173 dma -= XFER_MW_DMA_0; 174 175 pci_read_config_dword(pdev, ATIIXP_IDE_MWDMA_TIMING, 176 &mwdma_timing_data); 177 mwdma_timing_data &= ~(0xFF << timing_shift); 178 mwdma_timing_data |= (mwdma_timings[dma] << timing_shift); 179 pci_write_config_dword(pdev, ATIIXP_IDE_MWDMA_TIMING, 180 mwdma_timing_data); 181 } 182 /* 183 * We must now look at the PIO mode situation. We may need to 184 * adjust the PIO mode to keep the timings acceptable 185 */ 186 if (adev->dma_mode >= XFER_MW_DMA_2) 187 wanted_pio = 4; 188 else if (adev->dma_mode == XFER_MW_DMA_1) 189 wanted_pio = 3; 190 else if (adev->dma_mode == XFER_MW_DMA_0) 191 wanted_pio = 0; 192 else BUG(); 193 194 if (adev->pio_mode != wanted_pio) 195 atiixp_set_pio_timing(ap, adev, wanted_pio); 196 spin_unlock_irqrestore(&atiixp_lock, flags); 197 } 198 199 /** 200 * atiixp_bmdma_start - DMA start callback 201 * @qc: Command in progress 202 * 203 * When DMA begins we need to ensure that the UDMA control 204 * register for the channel is correctly set. 205 * 206 * Note: The host lock held by the libata layer protects 207 * us from two channels both trying to set DMA bits at once 208 */ 209 210 static void atiixp_bmdma_start(struct ata_queued_cmd *qc) 211 { 212 struct ata_port *ap = qc->ap; 213 struct ata_device *adev = qc->dev; 214 215 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 216 int dn = (2 * ap->port_no) + adev->devno; 217 u16 tmp16; 218 219 pci_read_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, &tmp16); 220 if (ata_using_udma(adev)) 221 tmp16 |= (1 << dn); 222 else 223 tmp16 &= ~(1 << dn); 224 pci_write_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, tmp16); 225 ata_bmdma_start(qc); 226 } 227 228 /** 229 * atiixp_dma_stop - DMA stop callback 230 * @qc: Command in progress 231 * 232 * DMA has completed. Clear the UDMA flag as the next operations will 233 * be PIO ones not UDMA data transfer. 234 * 235 * Note: The host lock held by the libata layer protects 236 * us from two channels both trying to set DMA bits at once 237 */ 238 239 static void atiixp_bmdma_stop(struct ata_queued_cmd *qc) 240 { 241 struct ata_port *ap = qc->ap; 242 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 243 int dn = (2 * ap->port_no) + qc->dev->devno; 244 u16 tmp16; 245 246 pci_read_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, &tmp16); 247 tmp16 &= ~(1 << dn); 248 pci_write_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, tmp16); 249 ata_bmdma_stop(qc); 250 } 251 252 static struct scsi_host_template atiixp_sht = { 253 ATA_BMDMA_SHT(DRV_NAME), 254 .sg_tablesize = LIBATA_DUMB_MAX_PRD, 255 }; 256 257 static struct ata_port_operations atiixp_port_ops = { 258 .inherits = &ata_bmdma_port_ops, 259 260 .qc_prep = ata_bmdma_dumb_qc_prep, 261 .bmdma_start = atiixp_bmdma_start, 262 .bmdma_stop = atiixp_bmdma_stop, 263 264 .prereset = atiixp_prereset, 265 .cable_detect = atiixp_cable_detect, 266 .set_piomode = atiixp_set_piomode, 267 .set_dmamode = atiixp_set_dmamode, 268 }; 269 270 static int atiixp_init_one(struct pci_dev *pdev, const struct pci_device_id *id) 271 { 272 static const struct ata_port_info info = { 273 .flags = ATA_FLAG_SLAVE_POSS, 274 .pio_mask = ATA_PIO4, 275 .mwdma_mask = ATA_MWDMA12_ONLY, 276 .udma_mask = ATA_UDMA5, 277 .port_ops = &atiixp_port_ops 278 }; 279 const struct ata_port_info *ppi[] = { &info, &info }; 280 281 /* SB600 doesn't have secondary port wired */ 282 if (pdev->device == PCI_DEVICE_ID_ATI_IXP600_IDE) 283 ppi[1] = &ata_dummy_port_info; 284 285 return ata_pci_bmdma_init_one(pdev, ppi, &atiixp_sht, NULL, 286 ATA_HOST_PARALLEL_SCAN); 287 } 288 289 static const struct pci_device_id atiixp[] = { 290 { PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP200_IDE), }, 291 { PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP300_IDE), }, 292 { PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP400_IDE), }, 293 { PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP600_IDE), }, 294 { PCI_VDEVICE(ATI, PCI_DEVICE_ID_ATI_IXP700_IDE), }, 295 { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_HUDSON2_IDE), }, 296 297 { }, 298 }; 299 300 static struct pci_driver atiixp_pci_driver = { 301 .name = DRV_NAME, 302 .id_table = atiixp, 303 .probe = atiixp_init_one, 304 .remove = ata_pci_remove_one, 305 #ifdef CONFIG_PM_SLEEP 306 .resume = ata_pci_device_resume, 307 .suspend = ata_pci_device_suspend, 308 #endif 309 }; 310 311 module_pci_driver(atiixp_pci_driver); 312 313 MODULE_AUTHOR("Alan Cox"); 314 MODULE_DESCRIPTION("low-level driver for ATI IXP200/300/400"); 315 MODULE_LICENSE("GPL"); 316 MODULE_DEVICE_TABLE(pci, atiixp); 317 MODULE_VERSION(DRV_VERSION); 318