1# SPDX-License-Identifier: GPL-2.0 2config XTENSA 3 def_bool y 4 select ARCH_32BIT_OFF_T 5 select ARCH_HAS_BINFMT_FLAT if !MMU 6 select ARCH_HAS_CURRENT_STACK_POINTER 7 select ARCH_HAS_DEBUG_VM_PGTABLE 8 select ARCH_HAS_DMA_PREP_COHERENT if MMU 9 select ARCH_HAS_GCOV_PROFILE_ALL 10 select ARCH_HAS_KCOV 11 select ARCH_HAS_SYNC_DMA_FOR_CPU if MMU 12 select ARCH_HAS_SYNC_DMA_FOR_DEVICE if MMU 13 select ARCH_HAS_DMA_SET_UNCACHED if MMU 14 select ARCH_HAS_STRNCPY_FROM_USER if !KASAN 15 select ARCH_HAS_STRNLEN_USER 16 select ARCH_USE_MEMTEST 17 select ARCH_USE_QUEUED_RWLOCKS 18 select ARCH_USE_QUEUED_SPINLOCKS 19 select ARCH_WANT_FRAME_POINTERS 20 select ARCH_WANT_IPC_PARSE_VERSION 21 select BUILDTIME_TABLE_SORT 22 select CLONE_BACKWARDS 23 select COMMON_CLK 24 select DMA_NONCOHERENT_MMAP if MMU 25 select GENERIC_ATOMIC64 26 select GENERIC_IRQ_SHOW 27 select GENERIC_LIB_CMPDI2 28 select GENERIC_LIB_MULDI3 29 select GENERIC_LIB_UCMPDI2 30 select GENERIC_PCI_IOMAP 31 select GENERIC_SCHED_CLOCK 32 select HAVE_ARCH_AUDITSYSCALL 33 select HAVE_ARCH_JUMP_LABEL if !XIP_KERNEL 34 select HAVE_ARCH_KASAN if MMU && !XIP_KERNEL 35 select HAVE_ARCH_KCSAN 36 select HAVE_ARCH_SECCOMP_FILTER 37 select HAVE_ARCH_TRACEHOOK 38 select HAVE_CONTEXT_TRACKING_USER 39 select HAVE_DEBUG_KMEMLEAK 40 select HAVE_DMA_CONTIGUOUS 41 select HAVE_EXIT_THREAD 42 select HAVE_FUNCTION_TRACER 43 select HAVE_GCC_PLUGINS if GCC_VERSION >= 120000 44 select HAVE_HW_BREAKPOINT if PERF_EVENTS 45 select HAVE_IRQ_TIME_ACCOUNTING 46 select HAVE_PCI 47 select HAVE_PERF_EVENTS 48 select HAVE_STACKPROTECTOR 49 select HAVE_SYSCALL_TRACEPOINTS 50 select HAVE_VIRT_CPU_ACCOUNTING_GEN 51 select IRQ_DOMAIN 52 select MODULES_USE_ELF_RELA 53 select PERF_USE_VMALLOC 54 select TRACE_IRQFLAGS_SUPPORT 55 help 56 Xtensa processors are 32-bit RISC machines designed by Tensilica 57 primarily for embedded systems. These processors are both 58 configurable and extensible. The Linux port to the Xtensa 59 architecture supports all processor configurations and extensions, 60 with reasonable minimum requirements. The Xtensa Linux project has 61 a home page at <http://www.linux-xtensa.org/>. 62 63config GENERIC_HWEIGHT 64 def_bool y 65 66config ARCH_HAS_ILOG2_U32 67 def_bool n 68 69config ARCH_HAS_ILOG2_U64 70 def_bool n 71 72config NO_IOPORT_MAP 73 def_bool n 74 75config HZ 76 int 77 default 100 78 79config LOCKDEP_SUPPORT 80 def_bool y 81 82config STACKTRACE_SUPPORT 83 def_bool y 84 85config MMU 86 def_bool n 87 select PFAULT 88 89config HAVE_XTENSA_GPIO32 90 def_bool n 91 92config KASAN_SHADOW_OFFSET 93 hex 94 default 0x6e400000 95 96config CPU_BIG_ENDIAN 97 def_bool $(success,test "$(shell,echo __XTENSA_EB__ | $(CC) -E -P -)" = 1) 98 99config CPU_LITTLE_ENDIAN 100 def_bool !CPU_BIG_ENDIAN 101 102config CC_HAVE_CALL0_ABI 103 def_bool $(success,test "$(shell,echo __XTENSA_CALL0_ABI__ | $(CC) -mabi=call0 -E -P - 2>/dev/null)" = 1) 104 105menu "Processor type and features" 106 107choice 108 prompt "Xtensa Processor Configuration" 109 default XTENSA_VARIANT_FSF 110 111config XTENSA_VARIANT_FSF 112 bool "fsf - default (not generic) configuration" 113 select MMU 114 115config XTENSA_VARIANT_DC232B 116 bool "dc232b - Diamond 232L Standard Core Rev.B (LE)" 117 select MMU 118 select HAVE_XTENSA_GPIO32 119 help 120 This variant refers to Tensilica's Diamond 232L Standard core Rev.B (LE). 121 122config XTENSA_VARIANT_DC233C 123 bool "dc233c - Diamond 233L Standard Core Rev.C (LE)" 124 select MMU 125 select HAVE_XTENSA_GPIO32 126 help 127 This variant refers to Tensilica's Diamond 233L Standard core Rev.C (LE). 128 129config XTENSA_VARIANT_CUSTOM 130 bool "Custom Xtensa processor configuration" 131 select HAVE_XTENSA_GPIO32 132 help 133 Select this variant to use a custom Xtensa processor configuration. 134 You will be prompted for a processor variant CORENAME. 135endchoice 136 137config XTENSA_VARIANT_CUSTOM_NAME 138 string "Xtensa Processor Custom Core Variant Name" 139 depends on XTENSA_VARIANT_CUSTOM 140 help 141 Provide the name of a custom Xtensa processor variant. 142 This CORENAME selects arch/xtensa/variant/CORENAME. 143 Don't forget you have to select MMU if you have one. 144 145config XTENSA_VARIANT_NAME 146 string 147 default "dc232b" if XTENSA_VARIANT_DC232B 148 default "dc233c" if XTENSA_VARIANT_DC233C 149 default "fsf" if XTENSA_VARIANT_FSF 150 default XTENSA_VARIANT_CUSTOM_NAME if XTENSA_VARIANT_CUSTOM 151 152config XTENSA_VARIANT_MMU 153 bool "Core variant has a Full MMU (TLB, Pages, Protection, etc)" 154 depends on XTENSA_VARIANT_CUSTOM 155 default y 156 select MMU 157 help 158 Build a Conventional Kernel with full MMU support, 159 ie: it supports a TLB with auto-loading, page protection. 160 161config XTENSA_VARIANT_HAVE_PERF_EVENTS 162 bool "Core variant has Performance Monitor Module" 163 depends on XTENSA_VARIANT_CUSTOM 164 default n 165 help 166 Enable if core variant has Performance Monitor Module with 167 External Registers Interface. 168 169 If unsure, say N. 170 171config XTENSA_FAKE_NMI 172 bool "Treat PMM IRQ as NMI" 173 depends on XTENSA_VARIANT_HAVE_PERF_EVENTS 174 default n 175 help 176 If PMM IRQ is the only IRQ at EXCM level it is safe to 177 treat it as NMI, which improves accuracy of profiling. 178 179 If there are other interrupts at or above PMM IRQ priority level 180 but not above the EXCM level, PMM IRQ still may be treated as NMI, 181 but only if these IRQs are not used. There will be a build warning 182 saying that this is not safe, and a bugcheck if one of these IRQs 183 actually fire. 184 185 If unsure, say N. 186 187config PFAULT 188 bool "Handle protection faults" if EXPERT && !MMU 189 default y 190 help 191 Handle protection faults. MMU configurations must enable it. 192 noMMU configurations may disable it if used memory map never 193 generates protection faults or faults are always fatal. 194 195 If unsure, say Y. 196 197config XTENSA_UNALIGNED_USER 198 bool "Unaligned memory access in user space" 199 help 200 The Xtensa architecture currently does not handle unaligned 201 memory accesses in hardware but through an exception handler. 202 Per default, unaligned memory accesses are disabled in user space. 203 204 Say Y here to enable unaligned memory access in user space. 205 206config HAVE_SMP 207 bool "System Supports SMP (MX)" 208 depends on XTENSA_VARIANT_CUSTOM 209 select XTENSA_MX 210 help 211 This option is used to indicate that the system-on-a-chip (SOC) 212 supports Multiprocessing. Multiprocessor support implemented above 213 the CPU core definition and currently needs to be selected manually. 214 215 Multiprocessor support is implemented with external cache and 216 interrupt controllers. 217 218 The MX interrupt distributer adds Interprocessor Interrupts 219 and causes the IRQ numbers to be increased by 4 for devices 220 like the open cores ethernet driver and the serial interface. 221 222 You still have to select "Enable SMP" to enable SMP on this SOC. 223 224config SMP 225 bool "Enable Symmetric multi-processing support" 226 depends on HAVE_SMP 227 select GENERIC_SMP_IDLE_THREAD 228 help 229 Enabled SMP Software; allows more than one CPU/CORE 230 to be activated during startup. 231 232config NR_CPUS 233 depends on SMP 234 int "Maximum number of CPUs (2-32)" 235 range 2 32 236 default "4" 237 238config HOTPLUG_CPU 239 bool "Enable CPU hotplug support" 240 depends on SMP 241 help 242 Say Y here to allow turning CPUs off and on. CPUs can be 243 controlled through /sys/devices/system/cpu. 244 245 Say N if you want to disable CPU hotplug. 246 247config SECONDARY_RESET_VECTOR 248 bool "Secondary cores use alternative reset vector" 249 default y 250 depends on HAVE_SMP 251 help 252 Secondary cores may be configured to use alternative reset vector, 253 or all cores may use primary reset vector. 254 Say Y here to supply handler for the alternative reset location. 255 256config FAST_SYSCALL_XTENSA 257 bool "Enable fast atomic syscalls" 258 default n 259 help 260 fast_syscall_xtensa is a syscall that can make atomic operations 261 on UP kernel when processor has no s32c1i support. 262 263 This syscall is deprecated. It may have issues when called with 264 invalid arguments. It is provided only for backwards compatibility. 265 Only enable it if your userspace software requires it. 266 267 If unsure, say N. 268 269config FAST_SYSCALL_SPILL_REGISTERS 270 bool "Enable spill registers syscall" 271 default n 272 help 273 fast_syscall_spill_registers is a syscall that spills all active 274 register windows of a calling userspace task onto its stack. 275 276 This syscall is deprecated. It may have issues when called with 277 invalid arguments. It is provided only for backwards compatibility. 278 Only enable it if your userspace software requires it. 279 280 If unsure, say N. 281 282choice 283 prompt "Kernel ABI" 284 default KERNEL_ABI_DEFAULT 285 help 286 Select ABI for the kernel code. This ABI is independent of the 287 supported userspace ABI and any combination of the 288 kernel/userspace ABI is possible and should work. 289 290 In case both kernel and userspace support only call0 ABI 291 all register windows support code will be omitted from the 292 build. 293 294 If unsure, choose the default ABI. 295 296config KERNEL_ABI_DEFAULT 297 bool "Default ABI" 298 help 299 Select this option to compile kernel code with the default ABI 300 selected for the toolchain. 301 Normally cores with windowed registers option use windowed ABI and 302 cores without it use call0 ABI. 303 304config KERNEL_ABI_CALL0 305 bool "Call0 ABI" if CC_HAVE_CALL0_ABI 306 help 307 Select this option to compile kernel code with call0 ABI even with 308 toolchain that defaults to windowed ABI. 309 When this option is not selected the default toolchain ABI will 310 be used for the kernel code. 311 312endchoice 313 314config USER_ABI_CALL0 315 bool 316 317choice 318 prompt "Userspace ABI" 319 default USER_ABI_DEFAULT 320 help 321 Select supported userspace ABI. 322 323 If unsure, choose the default ABI. 324 325config USER_ABI_DEFAULT 326 bool "Default ABI only" 327 help 328 Assume default userspace ABI. For XEA2 cores it is windowed ABI. 329 call0 ABI binaries may be run on such kernel, but signal delivery 330 will not work correctly for them. 331 332config USER_ABI_CALL0_ONLY 333 bool "Call0 ABI only" 334 select USER_ABI_CALL0 335 help 336 Select this option to support only call0 ABI in userspace. 337 Windowed ABI binaries will crash with a segfault caused by 338 an illegal instruction exception on the first 'entry' opcode. 339 340 Choose this option if you're planning to run only user code 341 built with call0 ABI. 342 343config USER_ABI_CALL0_PROBE 344 bool "Support both windowed and call0 ABI by probing" 345 select USER_ABI_CALL0 346 help 347 Select this option to support both windowed and call0 userspace 348 ABIs. When enabled all processes are started with PS.WOE disabled 349 and a fast user exception handler for an illegal instruction is 350 used to turn on PS.WOE bit on the first 'entry' opcode executed by 351 the userspace. 352 353 This option should be enabled for the kernel that must support 354 both call0 and windowed ABIs in userspace at the same time. 355 356 Note that Xtensa ISA does not guarantee that entry opcode will 357 raise an illegal instruction exception on cores with XEA2 when 358 PS.WOE is disabled, check whether the target core supports it. 359 360endchoice 361 362endmenu 363 364config XTENSA_CALIBRATE_CCOUNT 365 def_bool n 366 help 367 On some platforms (XT2000, for example), the CPU clock rate can 368 vary. The frequency can be determined, however, by measuring 369 against a well known, fixed frequency, such as an UART oscillator. 370 371config SERIAL_CONSOLE 372 def_bool n 373 374config PLATFORM_HAVE_XIP 375 def_bool n 376 377menu "Platform options" 378 379choice 380 prompt "Xtensa System Type" 381 default XTENSA_PLATFORM_ISS 382 383config XTENSA_PLATFORM_ISS 384 bool "ISS" 385 select XTENSA_CALIBRATE_CCOUNT 386 select SERIAL_CONSOLE 387 help 388 ISS is an acronym for Tensilica's Instruction Set Simulator. 389 390config XTENSA_PLATFORM_XT2000 391 bool "XT2000" 392 help 393 XT2000 is the name of Tensilica's feature-rich emulation platform. 394 This hardware is capable of running a full Linux distribution. 395 396config XTENSA_PLATFORM_XTFPGA 397 bool "XTFPGA" 398 select ETHOC if ETHERNET 399 select PLATFORM_WANT_DEFAULT_MEM if !MMU 400 select SERIAL_CONSOLE 401 select XTENSA_CALIBRATE_CCOUNT 402 select PLATFORM_HAVE_XIP 403 help 404 XTFPGA is the name of Tensilica board family (LX60, LX110, LX200, ML605). 405 This hardware is capable of running a full Linux distribution. 406 407endchoice 408 409config PLATFORM_NR_IRQS 410 int 411 default 3 if XTENSA_PLATFORM_XT2000 412 default 0 413 414config XTENSA_CPU_CLOCK 415 int "CPU clock rate [MHz]" 416 depends on !XTENSA_CALIBRATE_CCOUNT 417 default 16 418 419config GENERIC_CALIBRATE_DELAY 420 bool "Auto calibration of the BogoMIPS value" 421 help 422 The BogoMIPS value can easily be derived from the CPU frequency. 423 424config CMDLINE_BOOL 425 bool "Default bootloader kernel arguments" 426 427config CMDLINE 428 string "Initial kernel command string" 429 depends on CMDLINE_BOOL 430 default "console=ttyS0,38400 root=/dev/ram" 431 help 432 On some architectures (EBSA110 and CATS), there is currently no way 433 for the boot loader to pass arguments to the kernel. For these 434 architectures, you should supply some command-line options at build 435 time by entering them here. As a minimum, you should specify the 436 memory size and the root device (e.g., mem=64M root=/dev/nfs). 437 438config USE_OF 439 bool "Flattened Device Tree support" 440 select OF 441 select OF_EARLY_FLATTREE 442 help 443 Include support for flattened device tree machine descriptions. 444 445config BUILTIN_DTB_SOURCE 446 string "DTB to build into the kernel image" 447 depends on OF 448 449config PARSE_BOOTPARAM 450 bool "Parse bootparam block" 451 default y 452 help 453 Parse parameters passed to the kernel from the bootloader. It may 454 be disabled if the kernel is known to run without the bootloader. 455 456 If unsure, say Y. 457 458choice 459 prompt "Semihosting interface" 460 default XTENSA_SIMCALL_ISS 461 depends on XTENSA_PLATFORM_ISS 462 help 463 Choose semihosting interface that will be used for serial port, 464 block device and networking. 465 466config XTENSA_SIMCALL_ISS 467 bool "simcall" 468 help 469 Use simcall instruction. simcall is only available on simulators, 470 it does nothing on hardware. 471 472config XTENSA_SIMCALL_GDBIO 473 bool "GDBIO" 474 help 475 Use break instruction. It is available on real hardware when GDB 476 is attached to it via JTAG. 477 478endchoice 479 480config BLK_DEV_SIMDISK 481 tristate "Host file-based simulated block device support" 482 default n 483 depends on XTENSA_PLATFORM_ISS && BLOCK 484 help 485 Create block devices that map to files in the host file system. 486 Device binding to host file may be changed at runtime via proc 487 interface provided the device is not in use. 488 489config BLK_DEV_SIMDISK_COUNT 490 int "Number of host file-based simulated block devices" 491 range 1 10 492 depends on BLK_DEV_SIMDISK 493 default 2 494 help 495 This is the default minimal number of created block devices. 496 Kernel/module parameter 'simdisk_count' may be used to change this 497 value at runtime. More file names (but no more than 10) may be 498 specified as parameters, simdisk_count grows accordingly. 499 500config SIMDISK0_FILENAME 501 string "Host filename for the first simulated device" 502 depends on BLK_DEV_SIMDISK = y 503 default "" 504 help 505 Attach a first simdisk to a host file. Conventionally, this file 506 contains a root file system. 507 508config SIMDISK1_FILENAME 509 string "Host filename for the second simulated device" 510 depends on BLK_DEV_SIMDISK = y && BLK_DEV_SIMDISK_COUNT != 1 511 default "" 512 help 513 Another simulated disk in a host file for a buildroot-independent 514 storage. 515 516config XTFPGA_LCD 517 bool "Enable XTFPGA LCD driver" 518 depends on XTENSA_PLATFORM_XTFPGA 519 default n 520 help 521 There's a 2x16 LCD on most of XTFPGA boards, kernel may output 522 progress messages there during bootup/shutdown. It may be useful 523 during board bringup. 524 525 If unsure, say N. 526 527config XTFPGA_LCD_BASE_ADDR 528 hex "XTFPGA LCD base address" 529 depends on XTFPGA_LCD 530 default "0x0d0c0000" 531 help 532 Base address of the LCD controller inside KIO region. 533 Different boards from XTFPGA family have LCD controller at different 534 addresses. Please consult prototyping user guide for your board for 535 the correct address. Wrong address here may lead to hardware lockup. 536 537config XTFPGA_LCD_8BIT_ACCESS 538 bool "Use 8-bit access to XTFPGA LCD" 539 depends on XTFPGA_LCD 540 default n 541 help 542 LCD may be connected with 4- or 8-bit interface, 8-bit access may 543 only be used with 8-bit interface. Please consult prototyping user 544 guide for your board for the correct interface width. 545 546comment "Kernel memory layout" 547 548config INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX 549 bool "Initialize Xtensa MMU inside the Linux kernel code" 550 depends on !XTENSA_VARIANT_FSF && !XTENSA_VARIANT_DC232B 551 default y if XTENSA_VARIANT_DC233C || XTENSA_VARIANT_CUSTOM 552 help 553 Earlier version initialized the MMU in the exception vector 554 before jumping to _startup in head.S and had an advantage that 555 it was possible to place a software breakpoint at 'reset' and 556 then enter your normal kernel breakpoints once the MMU was mapped 557 to the kernel mappings (0XC0000000). 558 559 This unfortunately won't work for U-Boot and likely also won't 560 work for using KEXEC to have a hot kernel ready for doing a 561 KDUMP. 562 563 So now the MMU is initialized in head.S but it's necessary to 564 use hardware breakpoints (gdb 'hbreak' cmd) to break at _startup. 565 xt-gdb can't place a Software Breakpoint in the 0XD region prior 566 to mapping the MMU and after mapping even if the area of low memory 567 was mapped gdb wouldn't remove the breakpoint on hitting it as the 568 PC wouldn't match. Since Hardware Breakpoints are recommended for 569 Linux configurations it seems reasonable to just assume they exist 570 and leave this older mechanism for unfortunate souls that choose 571 not to follow Tensilica's recommendation. 572 573 Selecting this will cause U-Boot to set the KERNEL Load and Entry 574 address at 0x00003000 instead of the mapped std of 0xD0003000. 575 576 If in doubt, say Y. 577 578config XIP_KERNEL 579 bool "Kernel Execute-In-Place from ROM" 580 depends on PLATFORM_HAVE_XIP 581 help 582 Execute-In-Place allows the kernel to run from non-volatile storage 583 directly addressable by the CPU, such as NOR flash. This saves RAM 584 space since the text section of the kernel is not loaded from flash 585 to RAM. Read-write sections, such as the data section and stack, 586 are still copied to RAM. The XIP kernel is not compressed since 587 it has to run directly from flash, so it will take more space to 588 store it. The flash address used to link the kernel object files, 589 and for storing it, is configuration dependent. Therefore, if you 590 say Y here, you must know the proper physical address where to 591 store the kernel image depending on your own flash memory usage. 592 593 Also note that the make target becomes "make xipImage" rather than 594 "make Image" or "make uImage". The final kernel binary to put in 595 ROM memory will be arch/xtensa/boot/xipImage. 596 597 If unsure, say N. 598 599config MEMMAP_CACHEATTR 600 hex "Cache attributes for the memory address space" 601 depends on !MMU 602 default 0x22222222 603 help 604 These cache attributes are set up for noMMU systems. Each hex digit 605 specifies cache attributes for the corresponding 512MB memory 606 region: bits 0..3 -- for addresses 0x00000000..0x1fffffff, 607 bits 4..7 -- for addresses 0x20000000..0x3fffffff, and so on. 608 609 Cache attribute values are specific for the MMU type. 610 For region protection MMUs: 611 1: WT cached, 612 2: cache bypass, 613 4: WB cached, 614 f: illegal. 615 For full MMU: 616 bit 0: executable, 617 bit 1: writable, 618 bits 2..3: 619 0: cache bypass, 620 1: WB cache, 621 2: WT cache, 622 3: special (c and e are illegal, f is reserved). 623 For MPU: 624 0: illegal, 625 1: WB cache, 626 2: WB, no-write-allocate cache, 627 3: WT cache, 628 4: cache bypass. 629 630config KSEG_PADDR 631 hex "Physical address of the KSEG mapping" 632 depends on INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX && MMU 633 default 0x00000000 634 help 635 This is the physical address where KSEG is mapped. Please refer to 636 the chosen KSEG layout help for the required address alignment. 637 Unpacked kernel image (including vectors) must be located completely 638 within KSEG. 639 Physical memory below this address is not available to linux. 640 641 If unsure, leave the default value here. 642 643config KERNEL_VIRTUAL_ADDRESS 644 hex "Kernel virtual address" 645 depends on MMU && XIP_KERNEL 646 default 0xd0003000 647 help 648 This is the virtual address where the XIP kernel is mapped. 649 XIP kernel may be mapped into KSEG or KIO region, virtual address 650 provided here must match kernel load address provided in 651 KERNEL_LOAD_ADDRESS. 652 653config KERNEL_LOAD_ADDRESS 654 hex "Kernel load address" 655 default 0x60003000 if !MMU 656 default 0x00003000 if MMU && INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX 657 default 0xd0003000 if MMU && !INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX 658 help 659 This is the address where the kernel is loaded. 660 It is virtual address for MMUv2 configurations and physical address 661 for all other configurations. 662 663 If unsure, leave the default value here. 664 665choice 666 prompt "Relocatable vectors location" 667 default XTENSA_VECTORS_IN_TEXT 668 help 669 Choose whether relocatable vectors are merged into the kernel .text 670 or placed separately at runtime. This option does not affect 671 configurations without VECBASE register where vectors are always 672 placed at their hardware-defined locations. 673 674config XTENSA_VECTORS_IN_TEXT 675 bool "Merge relocatable vectors into kernel text" 676 depends on !MTD_XIP 677 help 678 This option puts relocatable vectors into the kernel .text section 679 with proper alignment. 680 This is a safe choice for most configurations. 681 682config XTENSA_VECTORS_SEPARATE 683 bool "Put relocatable vectors at fixed address" 684 help 685 This option puts relocatable vectors at specific virtual address. 686 Vectors are merged with the .init data in the kernel image and 687 are copied into their designated location during kernel startup. 688 Use it to put vectors into IRAM or out of FLASH on kernels with 689 XIP-aware MTD support. 690 691endchoice 692 693config VECTORS_ADDR 694 hex "Kernel vectors virtual address" 695 default 0x00000000 696 depends on XTENSA_VECTORS_SEPARATE 697 help 698 This is the virtual address of the (relocatable) vectors base. 699 It must be within KSEG if MMU is used. 700 701config XIP_DATA_ADDR 702 hex "XIP kernel data virtual address" 703 depends on XIP_KERNEL 704 default 0x00000000 705 help 706 This is the virtual address where XIP kernel data is copied. 707 It must be within KSEG if MMU is used. 708 709config PLATFORM_WANT_DEFAULT_MEM 710 def_bool n 711 712config DEFAULT_MEM_START 713 hex 714 prompt "PAGE_OFFSET/PHYS_OFFSET" if !MMU && PLATFORM_WANT_DEFAULT_MEM 715 default 0x60000000 if PLATFORM_WANT_DEFAULT_MEM 716 default 0x00000000 717 help 718 This is the base address used for both PAGE_OFFSET and PHYS_OFFSET 719 in noMMU configurations. 720 721 If unsure, leave the default value here. 722 723choice 724 prompt "KSEG layout" 725 depends on MMU 726 default XTENSA_KSEG_MMU_V2 727 728config XTENSA_KSEG_MMU_V2 729 bool "MMUv2: 128MB cached + 128MB uncached" 730 help 731 MMUv2 compatible kernel memory map: TLB way 5 maps 128MB starting 732 at KSEG_PADDR to 0xd0000000 with cache and to 0xd8000000 733 without cache. 734 KSEG_PADDR must be aligned to 128MB. 735 736config XTENSA_KSEG_256M 737 bool "256MB cached + 256MB uncached" 738 depends on INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX 739 help 740 TLB way 6 maps 256MB starting at KSEG_PADDR to 0xb0000000 741 with cache and to 0xc0000000 without cache. 742 KSEG_PADDR must be aligned to 256MB. 743 744config XTENSA_KSEG_512M 745 bool "512MB cached + 512MB uncached" 746 depends on INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX 747 help 748 TLB way 6 maps 512MB starting at KSEG_PADDR to 0xa0000000 749 with cache and to 0xc0000000 without cache. 750 KSEG_PADDR must be aligned to 256MB. 751 752endchoice 753 754config HIGHMEM 755 bool "High Memory Support" 756 depends on MMU 757 select KMAP_LOCAL 758 help 759 Linux can use the full amount of RAM in the system by 760 default. However, the default MMUv2 setup only maps the 761 lowermost 128 MB of memory linearly to the areas starting 762 at 0xd0000000 (cached) and 0xd8000000 (uncached). 763 When there are more than 128 MB memory in the system not 764 all of it can be "permanently mapped" by the kernel. 765 The physical memory that's not permanently mapped is called 766 "high memory". 767 768 If you are compiling a kernel which will never run on a 769 machine with more than 128 MB total physical RAM, answer 770 N here. 771 772 If unsure, say Y. 773 774config FORCE_MAX_ZONEORDER 775 int "Maximum zone order" 776 default "11" 777 help 778 The kernel memory allocator divides physically contiguous memory 779 blocks into "zones", where each zone is a power of two number of 780 pages. This option selects the largest power of two that the kernel 781 keeps in the memory allocator. If you need to allocate very large 782 blocks of physically contiguous memory, then you may need to 783 increase this value. 784 785 This config option is actually maximum order plus one. For example, 786 a value of 11 means that the largest free memory block is 2^10 pages. 787 788endmenu 789 790menu "Power management options" 791 792config ARCH_HIBERNATION_POSSIBLE 793 def_bool y 794 795source "kernel/power/Kconfig" 796 797endmenu 798