1 /* 2 * linux/include/asm/dma.h: Defines for using and allocating dma channels. 3 * Written by Hennus Bergman, 1992. 4 * High DMA channel support & info by Hannu Savolainen 5 * and John Boyd, Nov. 1992. 6 */ 7 8 #ifndef _ASM_X86_DMA_H 9 #define _ASM_X86_DMA_H 10 11 #include <linux/spinlock.h> /* And spinlocks */ 12 #include <asm/io.h> /* need byte IO */ 13 #include <linux/delay.h> 14 15 #ifdef HAVE_REALLY_SLOW_DMA_CONTROLLER 16 #define dma_outb outb_p 17 #else 18 #define dma_outb outb 19 #endif 20 21 #define dma_inb inb 22 23 /* 24 * NOTES about DMA transfers: 25 * 26 * controller 1: channels 0-3, byte operations, ports 00-1F 27 * controller 2: channels 4-7, word operations, ports C0-DF 28 * 29 * - ALL registers are 8 bits only, regardless of transfer size 30 * - channel 4 is not used - cascades 1 into 2. 31 * - channels 0-3 are byte - addresses/counts are for physical bytes 32 * - channels 5-7 are word - addresses/counts are for physical words 33 * - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries 34 * - transfer count loaded to registers is 1 less than actual count 35 * - controller 2 offsets are all even (2x offsets for controller 1) 36 * - page registers for 5-7 don't use data bit 0, represent 128K pages 37 * - page registers for 0-3 use bit 0, represent 64K pages 38 * 39 * DMA transfers are limited to the lower 16MB of _physical_ memory. 40 * Note that addresses loaded into registers must be _physical_ addresses, 41 * not logical addresses (which may differ if paging is active). 42 * 43 * Address mapping for channels 0-3: 44 * 45 * A23 ... A16 A15 ... A8 A7 ... A0 (Physical addresses) 46 * | ... | | ... | | ... | 47 * | ... | | ... | | ... | 48 * | ... | | ... | | ... | 49 * P7 ... P0 A7 ... A0 A7 ... A0 50 * | Page | Addr MSB | Addr LSB | (DMA registers) 51 * 52 * Address mapping for channels 5-7: 53 * 54 * A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0 (Physical addresses) 55 * | ... | \ \ ... \ \ \ ... \ \ 56 * | ... | \ \ ... \ \ \ ... \ (not used) 57 * | ... | \ \ ... \ \ \ ... \ 58 * P7 ... P1 (0) A7 A6 ... A0 A7 A6 ... A0 59 * | Page | Addr MSB | Addr LSB | (DMA registers) 60 * 61 * Again, channels 5-7 transfer _physical_ words (16 bits), so addresses 62 * and counts _must_ be word-aligned (the lowest address bit is _ignored_ at 63 * the hardware level, so odd-byte transfers aren't possible). 64 * 65 * Transfer count (_not # bytes_) is limited to 64K, represented as actual 66 * count - 1 : 64K => 0xFFFF, 1 => 0x0000. Thus, count is always 1 or more, 67 * and up to 128K bytes may be transferred on channels 5-7 in one operation. 68 * 69 */ 70 71 #define MAX_DMA_CHANNELS 8 72 73 #ifdef CONFIG_X86_32 74 75 /* The maximum address that we can perform a DMA transfer to on this platform */ 76 #define MAX_DMA_ADDRESS (PAGE_OFFSET + 0x1000000) 77 78 #else 79 80 /* 16MB ISA DMA zone */ 81 #define MAX_DMA_PFN ((16 * 1024 * 1024) >> PAGE_SHIFT) 82 83 /* 4GB broken PCI/AGP hardware bus master zone */ 84 #define MAX_DMA32_PFN ((4UL * 1024 * 1024 * 1024) >> PAGE_SHIFT) 85 86 /* Compat define for old dma zone */ 87 #define MAX_DMA_ADDRESS ((unsigned long)__va(MAX_DMA_PFN << PAGE_SHIFT)) 88 89 #endif 90 91 /* 8237 DMA controllers */ 92 #define IO_DMA1_BASE 0x00 /* 8 bit slave DMA, channels 0..3 */ 93 #define IO_DMA2_BASE 0xC0 /* 16 bit master DMA, ch 4(=slave input)..7 */ 94 95 /* DMA controller registers */ 96 #define DMA1_CMD_REG 0x08 /* command register (w) */ 97 #define DMA1_STAT_REG 0x08 /* status register (r) */ 98 #define DMA1_REQ_REG 0x09 /* request register (w) */ 99 #define DMA1_MASK_REG 0x0A /* single-channel mask (w) */ 100 #define DMA1_MODE_REG 0x0B /* mode register (w) */ 101 #define DMA1_CLEAR_FF_REG 0x0C /* clear pointer flip-flop (w) */ 102 #define DMA1_TEMP_REG 0x0D /* Temporary Register (r) */ 103 #define DMA1_RESET_REG 0x0D /* Master Clear (w) */ 104 #define DMA1_CLR_MASK_REG 0x0E /* Clear Mask */ 105 #define DMA1_MASK_ALL_REG 0x0F /* all-channels mask (w) */ 106 107 #define DMA2_CMD_REG 0xD0 /* command register (w) */ 108 #define DMA2_STAT_REG 0xD0 /* status register (r) */ 109 #define DMA2_REQ_REG 0xD2 /* request register (w) */ 110 #define DMA2_MASK_REG 0xD4 /* single-channel mask (w) */ 111 #define DMA2_MODE_REG 0xD6 /* mode register (w) */ 112 #define DMA2_CLEAR_FF_REG 0xD8 /* clear pointer flip-flop (w) */ 113 #define DMA2_TEMP_REG 0xDA /* Temporary Register (r) */ 114 #define DMA2_RESET_REG 0xDA /* Master Clear (w) */ 115 #define DMA2_CLR_MASK_REG 0xDC /* Clear Mask */ 116 #define DMA2_MASK_ALL_REG 0xDE /* all-channels mask (w) */ 117 118 #define DMA_ADDR_0 0x00 /* DMA address registers */ 119 #define DMA_ADDR_1 0x02 120 #define DMA_ADDR_2 0x04 121 #define DMA_ADDR_3 0x06 122 #define DMA_ADDR_4 0xC0 123 #define DMA_ADDR_5 0xC4 124 #define DMA_ADDR_6 0xC8 125 #define DMA_ADDR_7 0xCC 126 127 #define DMA_CNT_0 0x01 /* DMA count registers */ 128 #define DMA_CNT_1 0x03 129 #define DMA_CNT_2 0x05 130 #define DMA_CNT_3 0x07 131 #define DMA_CNT_4 0xC2 132 #define DMA_CNT_5 0xC6 133 #define DMA_CNT_6 0xCA 134 #define DMA_CNT_7 0xCE 135 136 #define DMA_PAGE_0 0x87 /* DMA page registers */ 137 #define DMA_PAGE_1 0x83 138 #define DMA_PAGE_2 0x81 139 #define DMA_PAGE_3 0x82 140 #define DMA_PAGE_5 0x8B 141 #define DMA_PAGE_6 0x89 142 #define DMA_PAGE_7 0x8A 143 144 /* I/O to memory, no autoinit, increment, single mode */ 145 #define DMA_MODE_READ 0x44 146 /* memory to I/O, no autoinit, increment, single mode */ 147 #define DMA_MODE_WRITE 0x48 148 /* pass thru DREQ->HRQ, DACK<-HLDA only */ 149 #define DMA_MODE_CASCADE 0xC0 150 151 #define DMA_AUTOINIT 0x10 152 153 154 #ifdef CONFIG_ISA_DMA_API 155 extern spinlock_t dma_spin_lock; 156 157 static inline unsigned long claim_dma_lock(void) 158 { 159 unsigned long flags; 160 spin_lock_irqsave(&dma_spin_lock, flags); 161 return flags; 162 } 163 164 static inline void release_dma_lock(unsigned long flags) 165 { 166 spin_unlock_irqrestore(&dma_spin_lock, flags); 167 } 168 #endif /* CONFIG_ISA_DMA_API */ 169 170 /* enable/disable a specific DMA channel */ 171 static inline void enable_dma(unsigned int dmanr) 172 { 173 if (dmanr <= 3) 174 dma_outb(dmanr, DMA1_MASK_REG); 175 else 176 dma_outb(dmanr & 3, DMA2_MASK_REG); 177 } 178 179 static inline void disable_dma(unsigned int dmanr) 180 { 181 if (dmanr <= 3) 182 dma_outb(dmanr | 4, DMA1_MASK_REG); 183 else 184 dma_outb((dmanr & 3) | 4, DMA2_MASK_REG); 185 } 186 187 /* Clear the 'DMA Pointer Flip Flop'. 188 * Write 0 for LSB/MSB, 1 for MSB/LSB access. 189 * Use this once to initialize the FF to a known state. 190 * After that, keep track of it. :-) 191 * --- In order to do that, the DMA routines below should --- 192 * --- only be used while holding the DMA lock ! --- 193 */ 194 static inline void clear_dma_ff(unsigned int dmanr) 195 { 196 if (dmanr <= 3) 197 dma_outb(0, DMA1_CLEAR_FF_REG); 198 else 199 dma_outb(0, DMA2_CLEAR_FF_REG); 200 } 201 202 /* set mode (above) for a specific DMA channel */ 203 static inline void set_dma_mode(unsigned int dmanr, char mode) 204 { 205 if (dmanr <= 3) 206 dma_outb(mode | dmanr, DMA1_MODE_REG); 207 else 208 dma_outb(mode | (dmanr & 3), DMA2_MODE_REG); 209 } 210 211 /* Set only the page register bits of the transfer address. 212 * This is used for successive transfers when we know the contents of 213 * the lower 16 bits of the DMA current address register, but a 64k boundary 214 * may have been crossed. 215 */ 216 static inline void set_dma_page(unsigned int dmanr, char pagenr) 217 { 218 switch (dmanr) { 219 case 0: 220 dma_outb(pagenr, DMA_PAGE_0); 221 break; 222 case 1: 223 dma_outb(pagenr, DMA_PAGE_1); 224 break; 225 case 2: 226 dma_outb(pagenr, DMA_PAGE_2); 227 break; 228 case 3: 229 dma_outb(pagenr, DMA_PAGE_3); 230 break; 231 case 5: 232 dma_outb(pagenr & 0xfe, DMA_PAGE_5); 233 break; 234 case 6: 235 dma_outb(pagenr & 0xfe, DMA_PAGE_6); 236 break; 237 case 7: 238 dma_outb(pagenr & 0xfe, DMA_PAGE_7); 239 break; 240 } 241 } 242 243 244 /* Set transfer address & page bits for specific DMA channel. 245 * Assumes dma flipflop is clear. 246 */ 247 static inline void set_dma_addr(unsigned int dmanr, unsigned int a) 248 { 249 set_dma_page(dmanr, a>>16); 250 if (dmanr <= 3) { 251 dma_outb(a & 0xff, ((dmanr & 3) << 1) + IO_DMA1_BASE); 252 dma_outb((a >> 8) & 0xff, ((dmanr & 3) << 1) + IO_DMA1_BASE); 253 } else { 254 dma_outb((a >> 1) & 0xff, ((dmanr & 3) << 2) + IO_DMA2_BASE); 255 dma_outb((a >> 9) & 0xff, ((dmanr & 3) << 2) + IO_DMA2_BASE); 256 } 257 } 258 259 260 /* Set transfer size (max 64k for DMA0..3, 128k for DMA5..7) for 261 * a specific DMA channel. 262 * You must ensure the parameters are valid. 263 * NOTE: from a manual: "the number of transfers is one more 264 * than the initial word count"! This is taken into account. 265 * Assumes dma flip-flop is clear. 266 * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7. 267 */ 268 static inline void set_dma_count(unsigned int dmanr, unsigned int count) 269 { 270 count--; 271 if (dmanr <= 3) { 272 dma_outb(count & 0xff, ((dmanr & 3) << 1) + 1 + IO_DMA1_BASE); 273 dma_outb((count >> 8) & 0xff, 274 ((dmanr & 3) << 1) + 1 + IO_DMA1_BASE); 275 } else { 276 dma_outb((count >> 1) & 0xff, 277 ((dmanr & 3) << 2) + 2 + IO_DMA2_BASE); 278 dma_outb((count >> 9) & 0xff, 279 ((dmanr & 3) << 2) + 2 + IO_DMA2_BASE); 280 } 281 } 282 283 284 /* Get DMA residue count. After a DMA transfer, this 285 * should return zero. Reading this while a DMA transfer is 286 * still in progress will return unpredictable results. 287 * If called before the channel has been used, it may return 1. 288 * Otherwise, it returns the number of _bytes_ left to transfer. 289 * 290 * Assumes DMA flip-flop is clear. 291 */ 292 static inline int get_dma_residue(unsigned int dmanr) 293 { 294 unsigned int io_port; 295 /* using short to get 16-bit wrap around */ 296 unsigned short count; 297 298 io_port = (dmanr <= 3) ? ((dmanr & 3) << 1) + 1 + IO_DMA1_BASE 299 : ((dmanr & 3) << 2) + 2 + IO_DMA2_BASE; 300 301 count = 1 + dma_inb(io_port); 302 count += dma_inb(io_port) << 8; 303 304 return (dmanr <= 3) ? count : (count << 1); 305 } 306 307 308 /* These are in kernel/dma.c because x86 uses CONFIG_GENERIC_ISA_DMA */ 309 #ifdef CONFIG_ISA_DMA_API 310 extern int request_dma(unsigned int dmanr, const char *device_id); 311 extern void free_dma(unsigned int dmanr); 312 #endif 313 314 /* From PCI */ 315 316 #ifdef CONFIG_PCI 317 extern int isa_dma_bridge_buggy; 318 #else 319 #define isa_dma_bridge_buggy (0) 320 #endif 321 322 #endif /* _ASM_X86_DMA_H */ 323