1/* 2 * P1025 TWR Device Tree Source stub (no addresses or top-level ranges) 3 * 4 * Copyright 2013 Freescale Semiconductor Inc. 5 * 6 * Redistribution and use in source and binary forms, with or without 7 * modification, are permitted provided that the following conditions are met: 8 * * Redistributions of source code must retain the above copyright 9 * notice, this list of conditions and the following disclaimer. 10 * * Redistributions in binary form must reproduce the above copyright 11 * notice, this list of conditions and the following disclaimer in the 12 * documentation and/or other materials provided with the distribution. 13 * * Neither the name of Freescale Semiconductor nor the 14 * names of its contributors may be used to endorse or promote products 15 * derived from this software without specific prior written permission. 16 * 17 * 18 * ALTERNATIVELY, this software may be distributed under the terms of the 19 * GNU General Public License ("GPL") as published by the Free Software 20 * Foundation, either version 2 of that License or (at your option) any 21 * later version. 22 * 23 * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY 24 * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED 25 * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 26 * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY 27 * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES 28 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; 29 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND 30 * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 31 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS 32 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 33 */ 34 35/{ 36 aliases { 37 ethernet3 = &enet3; 38 ethernet4 = &enet4; 39 }; 40}; 41 42&lbc { 43 nor@0,0 { 44 #address-cells = <1>; 45 #size-cells = <1>; 46 compatible = "cfi-flash"; 47 reg = <0x0 0x0 0x4000000>; 48 bank-width = <2>; 49 device-width = <1>; 50 51 partition@0 { 52 /* This location must not be altered */ 53 /* 256KB for Vitesse 7385 Switch firmware */ 54 reg = <0x0 0x00040000>; 55 label = "NOR Vitesse-7385 Firmware"; 56 read-only; 57 }; 58 59 partition@40000 { 60 /* 256KB for DTB Image */ 61 reg = <0x00040000 0x00040000>; 62 label = "NOR DTB Image"; 63 }; 64 65 partition@80000 { 66 /* 5.5 MB for Linux Kernel Image */ 67 reg = <0x00080000 0x00580000>; 68 label = "NOR Linux Kernel Image"; 69 }; 70 71 partition@400000 { 72 /* 56.75MB for Root file System */ 73 reg = <0x00600000 0x038c0000>; 74 label = "NOR Root File System"; 75 }; 76 77 partition@ec0000 { 78 /* This location must not be altered */ 79 /* 256KB for QE ucode firmware*/ 80 reg = <0x03ec0000 0x00040000>; 81 label = "NOR QE microcode firmware"; 82 read-only; 83 }; 84 85 partition@f00000 { 86 /* This location must not be altered */ 87 /* 512KB for u-boot Bootloader Image */ 88 /* 512KB for u-boot Environment Variables */ 89 reg = <0x03f00000 0x00100000>; 90 label = "NOR U-Boot Image"; 91 read-only; 92 }; 93 }; 94 95 /* CS2 for Display */ 96 display@2,0 { 97 compatible = "solomon,ssd1289fb"; 98 reg = <0x2 0x0000 0x0004>; 99 }; 100 101}; 102 103&soc { 104 usb@22000 { 105 phy_type = "ulpi"; 106 }; 107 108 mdio@24000 { 109 phy0: ethernet-phy@2 { 110 interrupt-parent = <&mpic>; 111 interrupts = <1 1 0 0>; 112 reg = <0x2>; 113 }; 114 115 phy1: ethernet-phy@1 { 116 interrupt-parent = <&mpic>; 117 interrupts = <2 1 0 0>; 118 reg = <0x1>; 119 }; 120 121 tbi0: tbi-phy@11 { 122 reg = <0x11>; 123 device_type = "tbi-phy"; 124 }; 125 }; 126 127 mdio@25000 { 128 tbi1: tbi-phy@11 { 129 reg = <0x11>; 130 device_type = "tbi-phy"; 131 }; 132 }; 133 134 mdio@26000 { 135 tbi2: tbi-phy@11 { 136 reg = <0x11>; 137 device_type = "tbi-phy"; 138 }; 139 }; 140 141 ptp_clock@b0e00 { 142 compatible = "fsl,etsec-ptp"; 143 reg = <0xb0e00 0xb0>; 144 interrupts = <68 2 0 0 69 2 0 0>; 145 fsl,tclk-period = <10>; 146 fsl,tmr-prsc = <2>; 147 fsl,tmr-add = <0xc0000021>; 148 fsl,tmr-fiper1 = <999999990>; 149 fsl,tmr-fiper2 = <99990>; 150 fsl,max-adj = <133333332>; 151 }; 152 153 enet0: ethernet@b0000 { 154 phy-handle = <&phy0>; 155 phy-connection-type = "rgmii-id"; 156 157 }; 158 159 enet1: ethernet@b1000 { 160 status = "disabled"; 161 }; 162 163 enet2: ethernet@b2000 { 164 phy-handle = <&phy1>; 165 phy-connection-type = "rgmii-id"; 166 }; 167 168 par_io@e0100 { 169 #address-cells = <1>; 170 #size-cells = <1>; 171 reg = <0xe0100 0x60>; 172 ranges = <0x0 0xe0100 0x60>; 173 device_type = "par_io"; 174 num-ports = <3>; 175 pio1: ucc_pin@01 { 176 pio-map = < 177 /* port pin dir open_drain assignment has_irq */ 178 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */ 179 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */ 180 0x0 0x17 0x2 0x0 0x2 0x0 /* CLK12 */ 181 0x0 0x18 0x2 0x0 0x1 0x0 /* CLK9 */ 182 0x0 0x7 0x1 0x0 0x2 0x0 /* ENET1_TXD0_SER1_TXD0 */ 183 0x0 0x9 0x1 0x0 0x2 0x0 /* ENET1_TXD1_SER1_TXD1 */ 184 0x0 0xb 0x1 0x0 0x2 0x0 /* ENET1_TXD2_SER1_TXD2 */ 185 0x0 0xc 0x1 0x0 0x2 0x0 /* ENET1_TXD3_SER1_TXD3 */ 186 0x0 0x6 0x2 0x0 0x2 0x0 /* ENET1_RXD0_SER1_RXD0 */ 187 0x0 0xa 0x2 0x0 0x2 0x0 /* ENET1_RXD1_SER1_RXD1 */ 188 0x0 0xe 0x2 0x0 0x2 0x0 /* ENET1_RXD2_SER1_RXD2 */ 189 0x0 0xf 0x2 0x0 0x2 0x0 /* ENET1_RXD3_SER1_RXD3 */ 190 0x0 0x5 0x1 0x0 0x2 0x0 /* ENET1_TX_EN_SER1_RTS_B */ 191 0x0 0xd 0x1 0x0 0x2 0x0 /* ENET1_TX_ER */ 192 0x0 0x4 0x2 0x0 0x2 0x0 /* ENET1_RX_DV_SER1_CTS_B */ 193 0x0 0x8 0x2 0x0 0x2 0x0 /* ENET1_RX_ER_SER1_CD_B */ 194 0x0 0x11 0x2 0x0 0x2 0x0 /* ENET1_CRS */ 195 0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */ 196 }; 197 198 pio2: ucc_pin@02 { 199 pio-map = < 200 /* port pin dir open_drain assignment has_irq */ 201 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */ 202 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */ 203 0x1 0xb 0x2 0x0 0x1 0x0 /* CLK13 */ 204 0x1 0x7 0x1 0x0 0x2 0x0 /* ENET5_TXD0_SER5_TXD0 */ 205 0x1 0xa 0x1 0x0 0x2 0x0 /* ENET5_TXD1_SER5_TXD1 */ 206 0x1 0x6 0x2 0x0 0x2 0x0 /* ENET5_RXD0_SER5_RXD0 */ 207 0x1 0x9 0x2 0x0 0x2 0x0 /* ENET5_RXD1_SER5_RXD1 */ 208 0x1 0x5 0x1 0x0 0x2 0x0 /* ENET5_TX_EN_SER5_RTS_B */ 209 0x1 0x4 0x2 0x0 0x2 0x0 /* ENET5_RX_DV_SER5_CTS_B */ 210 0x1 0x8 0x2 0x0 0x2 0x0>; /* ENET5_RX_ER_SER5_CD_B */ 211 }; 212 213 pio3: ucc_pin@03 { 214 pio-map = < 215 /* port pin dir open_drain assignment has_irq */ 216 0x0 0x16 0x2 0x0 0x2 0x0 /* SER7_CD_B*/ 217 0x0 0x12 0x2 0x0 0x2 0x0 /* SER7_CTS_B*/ 218 0x0 0x13 0x1 0x0 0x2 0x0 /* SER7_RTS_B*/ 219 0x0 0x14 0x2 0x0 0x2 0x0 /* SER7_RXD0*/ 220 0x0 0x15 0x1 0x0 0x2 0x0>; /* SER7_TXD0*/ 221 }; 222 223 pio4: ucc_pin@04 { 224 pio-map = < 225 /* port pin dir open_drain assignment has_irq */ 226 0x1 0x0 0x2 0x0 0x2 0x0 /* SER3_CD_B*/ 227 0x0 0x1c 0x2 0x0 0x2 0x0 /* SER3_CTS_B*/ 228 0x0 0x1d 0x1 0x0 0x2 0x0 /* SER3_RTS_B*/ 229 0x0 0x1e 0x2 0x0 0x2 0x0 /* SER3_RXD0*/ 230 0x0 0x1f 0x1 0x0 0x2 0x0>; /* SER3_TXD0*/ 231 }; 232 }; 233}; 234 235&qe { 236 enet3: ucc@2000 { 237 device_type = "network"; 238 compatible = "ucc_geth"; 239 rx-clock-name = "clk12"; 240 tx-clock-name = "clk9"; 241 pio-handle = <&pio1>; 242 phy-handle = <&qe_phy0>; 243 phy-connection-type = "mii"; 244 }; 245 246 mdio@2120 { 247 qe_phy0: ethernet-phy@18 { 248 interrupt-parent = <&mpic>; 249 interrupts = <4 1 0 0>; 250 reg = <0x18>; 251 device_type = "ethernet-phy"; 252 }; 253 qe_phy1: ethernet-phy@19 { 254 interrupt-parent = <&mpic>; 255 interrupts = <5 1 0 0>; 256 reg = <0x19>; 257 device_type = "ethernet-phy"; 258 }; 259 tbi-phy@11 { 260 reg = <0x11>; 261 device_type = "tbi-phy"; 262 }; 263 }; 264 265 enet4: ucc@2400 { 266 device_type = "network"; 267 compatible = "ucc_geth"; 268 rx-clock-name = "none"; 269 tx-clock-name = "clk13"; 270 pio-handle = <&pio2>; 271 phy-handle = <&qe_phy1>; 272 phy-connection-type = "rmii"; 273 }; 274 275 serial2: ucc@2600 { 276 device_type = "serial"; 277 compatible = "ucc_uart"; 278 port-number = <0>; 279 rx-clock-name = "brg6"; 280 tx-clock-name = "brg6"; 281 pio-handle = <&pio3>; 282 }; 283 284 serial3: ucc@2200 { 285 device_type = "serial"; 286 compatible = "ucc_uart"; 287 port-number = <1>; 288 rx-clock-name = "brg2"; 289 tx-clock-name = "brg2"; 290 pio-handle = <&pio4>; 291 }; 292}; 293