1// SPDX-License-Identifier: GPL-2.0 2/dts-v1/; 3 4#include "jz4770.dtsi" 5#include <dt-bindings/clock/ingenic,tcu.h> 6 7#include <dt-bindings/gpio/gpio.h> 8#include <dt-bindings/iio/adc/ingenic,adc.h> 9#include <dt-bindings/input/input.h> 10 11/ { 12 compatible = "gcw,zero", "ingenic,jz4770"; 13 model = "GCW Zero"; 14 15 aliases { 16 serial0 = &uart0; 17 serial1 = &uart1; 18 serial2 = &uart2; 19 serial3 = &uart3; 20 }; 21 22 memory: memory { 23 device_type = "memory"; 24 reg = <0x0 0x10000000>, 25 <0x30000000 0x10000000>; 26 }; 27 28 chosen { 29 stdout-path = "serial2:57600n8"; 30 }; 31 32 vcc: regulator@0 { 33 compatible = "regulator-fixed"; 34 regulator-name = "vcc"; 35 36 regulator-min-microvolt = <3300000>; 37 regulator-max-microvolt = <3300000>; 38 regulator-always-on; 39 }; 40 41 mmc1_power: regulator@1 { 42 compatible = "regulator-fixed"; 43 regulator-name = "mmc1_vcc"; 44 gpio = <&gpe 9 0>; 45 46 regulator-min-microvolt = <3300000>; 47 regulator-max-microvolt = <3300000>; 48 vin-supply = <&vcc>; 49 }; 50 51 headphones_amp: analog-amplifier@0 { 52 compatible = "simple-audio-amplifier"; 53 enable-gpios = <&gpf 3 GPIO_ACTIVE_LOW>; 54 enable-delay-ms = <50>; 55 56 VCC-supply = <&ldo5>; 57 sound-name-prefix = "Headphones Amp"; 58 }; 59 60 speaker_amp: analog-amplifier@1 { 61 compatible = "simple-audio-amplifier"; 62 enable-gpios = <&gpf 20 GPIO_ACTIVE_HIGH>; 63 64 VCC-supply = <&ldo5>; 65 sound-name-prefix = "Speaker Amp"; 66 }; 67 68 sound { 69 compatible = "simple-audio-card"; 70 71 simple-audio-card,name = "gcw0-audio"; 72 simple-audio-card,format = "i2s"; 73 74 simple-audio-card,widgets = 75 "Speaker", "Speaker", 76 "Headphone", "Headphones", 77 "Microphone", "Built-in Mic"; 78 simple-audio-card,routing = 79 "Headphones Amp INL", "LHPOUT", 80 "Headphones Amp INR", "RHPOUT", 81 "Headphones", "Headphones Amp OUTL", 82 "Headphones", "Headphones Amp OUTR", 83 "Speaker Amp INL", "LOUT", 84 "Speaker Amp INR", "ROUT", 85 "Speaker", "Speaker Amp OUTL", 86 "Speaker", "Speaker Amp OUTR", 87 "LLINEIN", "Cap-less", 88 "RLINEIN", "Cap-less", 89 "Built-in Mic", "MICBIAS", 90 "MIC1P", "Built-in Mic", 91 "MIC1N", "Built-in Mic"; 92 simple-audio-card,pin-switches = "Speaker", "Headphones"; 93 94 simple-audio-card,hp-det-gpio = <&gpf 21 GPIO_ACTIVE_LOW>; 95 simple-audio-card,aux-devs = <&speaker_amp>, <&headphones_amp>; 96 97 simple-audio-card,bitclock-master = <&dai_codec>; 98 simple-audio-card,frame-master = <&dai_codec>; 99 100 dai_cpu: simple-audio-card,cpu { 101 sound-dai = <&aic>; 102 }; 103 104 dai_codec: simple-audio-card,codec { 105 sound-dai = <&codec>; 106 }; 107 }; 108 109 rumble { 110 compatible = "pwm-vibrator"; 111 pwms = <&pwm 4 2000000 0>; 112 pwm-names = "enable"; 113 114 pinctrl-names = "default"; 115 pinctrl-0 = <&pins_pwm4>; 116 }; 117 118 backlight: backlight { 119 compatible = "pwm-backlight"; 120 pwms = <&pwm 1 40000 0>; 121 power-supply = <&vcc>; 122 123 brightness-levels = <0 16 32 48 64 80 96 112 128 124 144 160 176 192 208 224 240 255>; 125 default-brightness-level = <12>; 126 127 pinctrl-names = "default"; 128 pinctrl-0 = <&pins_pwm1>; 129 }; 130 131 gpio-keys { 132 compatible = "gpio-keys"; 133 autorepeat; 134 135 button-0 { 136 label = "D-pad up"; 137 linux,code = <KEY_UP>; 138 linux,can-disable; 139 gpios = <&gpe 21 GPIO_ACTIVE_LOW>; 140 }; 141 142 button-1 { 143 label = "D-pad down"; 144 linux,code = <KEY_DOWN>; 145 linux,can-disable; 146 gpios = <&gpe 25 GPIO_ACTIVE_LOW>; 147 }; 148 149 button-2 { 150 label = "D-pad left"; 151 linux,code = <KEY_LEFT>; 152 linux,can-disable; 153 gpios = <&gpe 23 GPIO_ACTIVE_LOW>; 154 }; 155 156 button-3 { 157 label = "D-pad right"; 158 linux,code = <KEY_RIGHT>; 159 linux,can-disable; 160 gpios = <&gpe 24 GPIO_ACTIVE_LOW>; 161 }; 162 163 button-4 { 164 label = "Button A"; 165 linux,code = <KEY_LEFTCTRL>; 166 linux,can-disable; 167 gpios = <&gpe 29 GPIO_ACTIVE_LOW>; 168 }; 169 170 button-5 { 171 label = "Button B"; 172 linux,code = <KEY_LEFTALT>; 173 linux,can-disable; 174 gpios = <&gpe 20 GPIO_ACTIVE_LOW>; 175 }; 176 177 button-6 { 178 label = "Button Y"; 179 linux,code = <KEY_SPACE>; 180 linux,can-disable; 181 gpios = <&gpe 27 GPIO_ACTIVE_LOW>; 182 }; 183 184 button-7 { 185 label = "Button X"; 186 linux,code = <KEY_LEFTSHIFT>; 187 linux,can-disable; 188 gpios = <&gpe 28 GPIO_ACTIVE_LOW>; 189 }; 190 191 button-8 { 192 label = "Left shoulder button"; 193 linux,code = <KEY_TAB>; 194 linux,can-disable; 195 gpios = <&gpb 20 GPIO_ACTIVE_LOW>; 196 }; 197 198 button-9 { 199 label = "Right shoulder button"; 200 linux,code = <KEY_BACKSPACE>; 201 linux,can-disable; 202 gpios = <&gpe 26 GPIO_ACTIVE_LOW>; 203 }; 204 205 button-10 { 206 label = "Start button"; 207 linux,code = <KEY_ENTER>; 208 linux,can-disable; 209 gpios = <&gpb 21 GPIO_ACTIVE_LOW>; 210 }; 211 212 button-11 { 213 label = "Select button"; 214 linux,code = <KEY_ESC>; 215 linux,can-disable; 216 /* 217 * This is the only button that is active high, 218 * since it doubles as BOOT_SEL1. 219 */ 220 gpios = <&gpd 18 GPIO_ACTIVE_HIGH>; 221 }; 222 223 button-12 { 224 label = "Power slider"; 225 linux,code = <KEY_POWER>; 226 linux,can-disable; 227 gpios = <&gpa 30 GPIO_ACTIVE_LOW>; 228 wakeup-source; 229 }; 230 231 button-13 { 232 label = "Power hold"; 233 linux,code = <KEY_PAUSE>; 234 linux,can-disable; 235 gpios = <&gpf 11 GPIO_ACTIVE_LOW>; 236 }; 237 }; 238 239 i2c3: i2c-controller@3 { 240 compatible = "i2c-gpio"; 241 #address-cells = <1>; 242 #size-cells = <0>; 243 244 sda-gpios = <&gpd 5 GPIO_ACTIVE_HIGH>; 245 scl-gpios = <&gpd 4 GPIO_ACTIVE_HIGH>; 246 i2c-gpio,delay-us = <2>; /* 250 kHz */ 247 248 act8600: pmic@5a { 249 compatible = "active-semi,act8600"; 250 reg = <0x5a>; 251 252 regulators { 253 /* USB OTG */ 254 otg_vbus: SUDCDC_REG4 { 255 /* 256 * 5.3V instead of 5.0V to compensate 257 * for the voltage drop of a diode 258 * between the regulator and the 259 * connector. 260 */ 261 regulator-min-microvolt = <5300000>; 262 regulator-max-microvolt = <5300000>; 263 inl-supply = <&vcc>; 264 }; 265 266 /* 267 * When this is off, there is no sound, but also 268 * no USB networking. 269 */ 270 ldo5: LDO5 { 271 regulator-min-microvolt = <2500000>; 272 regulator-max-microvolt = <2500000>; 273 inl-supply = <&vcc>; 274 }; 275 276 /* LCD panel and FM radio */ 277 ldo6: LDO6 { 278 regulator-min-microvolt = <3300000>; 279 regulator-max-microvolt = <3300000>; 280 inl-supply = <&vcc>; 281 }; 282 283 /* ??? */ 284 LDO7 { 285 regulator-min-microvolt = <3300000>; 286 regulator-max-microvolt = <3300000>; 287 /*regulator-always-on;*/ 288 inl-supply = <&vcc>; 289 }; 290 291 /* 292 * The colors on the LCD are wrong when this is 293 * off. Which is strange, since the LCD panel 294 * data sheet only mentions a 3.3V input. 295 */ 296 LDO8 { 297 regulator-min-microvolt = <1800000>; 298 regulator-max-microvolt = <1800000>; 299 regulator-always-on; 300 inl-supply = <&vcc>; 301 }; 302 303 /* RTC fixed 3.3V */ 304 LDO_REG9 { 305 regulator-min-microvolt = <3300000>; 306 regulator-max-microvolt = <3300000>; 307 regulator-always-on; 308 inl-supply = <&vcc>; 309 }; 310 311 /* Unused fixed 1.2V */ 312 LDO_REG10 { 313 inl-supply = <&vcc>; 314 }; 315 }; 316 }; 317 }; 318 319 leds { 320 compatible = "gpio-leds"; 321 322 led { 323 gpios = <&gpb 30 GPIO_ACTIVE_LOW>; 324 default-state = "on"; 325 }; 326 }; 327 328 spi { 329 compatible = "spi-gpio"; 330 #address-cells = <1>; 331 #size-cells = <0>; 332 333 sck-gpios = <&gpe 15 GPIO_ACTIVE_HIGH>; 334 mosi-gpios = <&gpe 17 GPIO_ACTIVE_HIGH>; 335 cs-gpios = <&gpe 16 GPIO_ACTIVE_HIGH>; 336 num-chipselects = <1>; 337 338 nt39016@0 { 339 compatible = "kingdisplay,kd035g6-54nt"; 340 reg = <0>; 341 342 spi-max-frequency = <3125000>; 343 spi-3wire; 344 345 reset-gpios = <&gpe 2 GPIO_ACTIVE_LOW>; 346 347 backlight = <&backlight>; 348 power-supply = <&ldo6>; 349 350 port { 351 panel_input: endpoint { 352 remote-endpoint = <&panel_output>; 353 }; 354 }; 355 }; 356 }; 357 358 connector { 359 compatible = "gpio-usb-b-connector", "usb-b-connector"; 360 label = "mini-USB"; 361 type = "mini"; 362 363 /* 364 * USB OTG is not yet working reliably, the ID detection 365 * mechanism tends to fry easily for unknown reasons. 366 * Until this is fixed, disable OTG by not providing the 367 * ID GPIO to the driver. 368 */ 369 //id-gpios = <&gpf 18 GPIO_ACTIVE_LOW>; 370 371 vbus-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>; 372 vbus-supply = <&otg_vbus>; 373 374 pinctrl-names = "default"; 375 pinctrl-0 = <&pins_otg>; 376 377 port { 378 usb_ep: endpoint { 379 remote-endpoint = <&usb_otg_ep>; 380 }; 381 }; 382 }; 383}; 384 385&ext { 386 clock-frequency = <12000000>; 387}; 388 389&pinctrl { 390 pins_lcd: lcd { 391 function = "lcd"; 392 groups = "lcd-24bit"; 393 }; 394 395 pins_uart2: uart2 { 396 function = "uart2"; 397 groups = "uart2-data"; 398 }; 399 400 pins_mmc0: mmc0 { 401 function = "mmc0"; 402 groups = "mmc0-1bit-a", "mmc0-4bit-a"; 403 }; 404 405 pins_mmc1: mmc1 { 406 function = "mmc1"; 407 groups = "mmc1-1bit-d", "mmc1-4bit-d"; 408 }; 409 410 pins_otg: otg { 411 otg-vbus-pin { 412 function = "otg"; 413 groups = "otg-vbus"; 414 }; 415 416 vbus-pin { 417 pins = "PB5"; 418 bias-disable; 419 }; 420 }; 421 422 pins_pwm1: pwm1 { 423 function = "pwm1"; 424 groups = "pwm1"; 425 }; 426 427 pins_pwm4: pwm4 { 428 function = "pwm4"; 429 groups = "pwm4"; 430 }; 431}; 432 433&uart2 { 434 pinctrl-names = "default"; 435 pinctrl-0 = <&pins_uart2>; 436 437 status = "okay"; 438}; 439 440&cgu { 441 /* 442 * Put high-speed peripherals under PLL1, such that we can change the 443 * PLL0 frequency on demand without having to suspend peripherals. 444 * We use a rate of 432 MHz, which is the least common multiple of 445 * 27 MHz (required by TV encoder) and 48 MHz (required by USB host). 446 * Put the GPU under PLL0 since we want a higher frequency. 447 * Use the 32 kHz oscillator as the parent of the RTC for a higher 448 * precision. 449 */ 450 assigned-clocks = 451 <&cgu JZ4770_CLK_PLL1>, 452 <&cgu JZ4770_CLK_GPU>, 453 <&cgu JZ4770_CLK_RTC>, 454 <&cgu JZ4770_CLK_UHC>, 455 <&cgu JZ4770_CLK_LPCLK_MUX>, 456 <&cgu JZ4770_CLK_MMC0_MUX>, 457 <&cgu JZ4770_CLK_MMC1_MUX>; 458 assigned-clock-parents = 459 <0>, 460 <&cgu JZ4770_CLK_PLL0>, 461 <&cgu JZ4770_CLK_OSC32K>, 462 <&cgu JZ4770_CLK_PLL1>, 463 <&cgu JZ4770_CLK_PLL1>, 464 <&cgu JZ4770_CLK_PLL1>, 465 <&cgu JZ4770_CLK_PLL1>; 466 assigned-clock-rates = 467 <432000000>, 468 <600000000>; 469}; 470 471&uhc { 472 /* The WiFi module is connected to the UHC. */ 473 status = "okay"; 474}; 475 476&tcu { 477 /* 478 * 750 kHz for the system timer and clocksource, 12 MHz for the OST, 479 * and use RTC as the parent for the watchdog clock 480 */ 481 assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>, 482 <&tcu TCU_CLK_OST>, <&tcu TCU_CLK_WDT>; 483 assigned-clock-parents = <0>, <0>, <0>, <&cgu JZ4770_CLK_RTC>; 484 assigned-clock-rates = <750000>, <750000>, <12000000>; 485 486 /* PWM1 is in use, so use channel #2 for the clocksource */ 487 ingenic,pwm-channels-mask = <0xfa>; 488}; 489 490&usb_otg { 491 port { 492 usb_otg_ep: endpoint { 493 remote-endpoint = <&usb_ep>; 494 }; 495 }; 496}; 497 498&otg_phy { 499 vcc-supply = <&ldo5>; 500}; 501 502&rtc { 503 clocks = <&cgu JZ4770_CLK_RTC>; 504 clock-names = "rtc"; 505 506 system-power-controller; 507}; 508 509&mmc0 { 510 status = "okay"; 511 512 bus-width = <4>; 513 max-frequency = <48000000>; 514 vmmc-supply = <&vcc>; 515 non-removable; 516 517 pinctrl-names = "default"; 518 pinctrl-0 = <&pins_mmc0>; 519}; 520 521&mmc1 { 522 status = "okay"; 523 524 bus-width = <4>; 525 max-frequency = <48000000>; 526 cd-gpios = <&gpb 2 GPIO_ACTIVE_LOW>; 527 vmmc-supply = <&mmc1_power>; 528 529 pinctrl-names = "default"; 530 pinctrl-0 = <&pins_mmc1>; 531}; 532 533&lcd { 534 pinctrl-names = "default"; 535 pinctrl-0 = <&pins_lcd>; 536 537 port { 538 panel_output: endpoint { 539 remote-endpoint = <&panel_input>; 540 }; 541 }; 542}; 543