1 // SPDX-License-Identifier: GPL-2.0
2 /***************************************************************************/
3
4 /*
5 * sltimers.c -- generic ColdFire slice timer support.
6 *
7 * Copyright (C) 2009-2010, Philippe De Muyter <phdm@macqel.be>
8 * based on
9 * timers.c -- generic ColdFire hardware timer support.
10 * Copyright (C) 1999-2008, Greg Ungerer <gerg@snapgear.com>
11 */
12
13 /***************************************************************************/
14
15 #include <linux/kernel.h>
16 #include <linux/init.h>
17 #include <linux/sched.h>
18 #include <linux/interrupt.h>
19 #include <linux/irq.h>
20 #include <linux/profile.h>
21 #include <linux/clocksource.h>
22 #include <asm/io.h>
23 #include <asm/traps.h>
24 #include <asm/machdep.h>
25 #include <asm/coldfire.h>
26 #include <asm/mcfslt.h>
27 #include <asm/mcfsim.h>
28
29 /***************************************************************************/
30
31 #ifdef CONFIG_HIGHPROFILE
32
33 /*
34 * By default use Slice Timer 1 as the profiler clock timer.
35 */
36 #define PA(a) (MCFSLT_TIMER1 + (a))
37
38 /*
39 * Choose a reasonably fast profile timer. Make it an odd value to
40 * try and get good coverage of kernel operations.
41 */
42 #define PROFILEHZ 1013
43
mcfslt_profile_tick(int irq,void * dummy)44 irqreturn_t mcfslt_profile_tick(int irq, void *dummy)
45 {
46 /* Reset Slice Timer 1 */
47 __raw_writel(MCFSLT_SSR_BE | MCFSLT_SSR_TE, PA(MCFSLT_SSR));
48 if (current->pid)
49 profile_tick(CPU_PROFILING);
50 return IRQ_HANDLED;
51 }
52
mcfslt_profile_init(void)53 void mcfslt_profile_init(void)
54 {
55 int ret;
56
57 printk(KERN_INFO "PROFILE: lodging TIMER 1 @ %dHz as profile timer\n",
58 PROFILEHZ);
59
60 ret = request_irq(MCF_IRQ_PROFILER, mcfslt_profile_tick, IRQF_TIMER,
61 "profile timer", NULL);
62 if (ret) {
63 pr_err("Failed to request irq %d (profile timer): %pe\n",
64 MCF_IRQ_PROFILER, ERR_PTR(ret));
65 }
66
67 /* Set up TIMER 2 as high speed profile clock */
68 __raw_writel(MCF_BUSCLK / PROFILEHZ - 1, PA(MCFSLT_STCNT));
69 __raw_writel(MCFSLT_SCR_RUN | MCFSLT_SCR_IEN | MCFSLT_SCR_TEN,
70 PA(MCFSLT_SCR));
71
72 }
73
74 #endif /* CONFIG_HIGHPROFILE */
75
76 /***************************************************************************/
77
78 /*
79 * By default use Slice Timer 0 as the system clock timer.
80 */
81 #define TA(a) (MCFSLT_TIMER0 + (a))
82
83 static u32 mcfslt_cycles_per_jiffy;
84 static u32 mcfslt_cnt;
85
mcfslt_tick(int irq,void * dummy)86 static irqreturn_t mcfslt_tick(int irq, void *dummy)
87 {
88 /* Reset Slice Timer 0 */
89 __raw_writel(MCFSLT_SSR_BE | MCFSLT_SSR_TE, TA(MCFSLT_SSR));
90 mcfslt_cnt += mcfslt_cycles_per_jiffy;
91 legacy_timer_tick(1);
92 return IRQ_HANDLED;
93 }
94
mcfslt_read_clk(struct clocksource * cs)95 static u64 mcfslt_read_clk(struct clocksource *cs)
96 {
97 unsigned long flags;
98 u32 cycles, scnt;
99
100 local_irq_save(flags);
101 scnt = __raw_readl(TA(MCFSLT_SCNT));
102 cycles = mcfslt_cnt;
103 if (__raw_readl(TA(MCFSLT_SSR)) & MCFSLT_SSR_TE) {
104 cycles += mcfslt_cycles_per_jiffy;
105 scnt = __raw_readl(TA(MCFSLT_SCNT));
106 }
107 local_irq_restore(flags);
108
109 /* subtract because slice timers count down */
110 return cycles + ((mcfslt_cycles_per_jiffy - 1) - scnt);
111 }
112
113 static struct clocksource mcfslt_clk = {
114 .name = "slt",
115 .rating = 250,
116 .read = mcfslt_read_clk,
117 .mask = CLOCKSOURCE_MASK(32),
118 .flags = CLOCK_SOURCE_IS_CONTINUOUS,
119 };
120
hw_timer_init(void)121 void hw_timer_init(void)
122 {
123 int r;
124
125 mcfslt_cycles_per_jiffy = MCF_BUSCLK / HZ;
126 /*
127 * The coldfire slice timer (SLT) runs from STCNT to 0 included,
128 * then STCNT again and so on. It counts thus actually
129 * STCNT + 1 steps for 1 tick, not STCNT. So if you want
130 * n cycles, initialize STCNT with n - 1.
131 */
132 __raw_writel(mcfslt_cycles_per_jiffy - 1, TA(MCFSLT_STCNT));
133 __raw_writel(MCFSLT_SCR_RUN | MCFSLT_SCR_IEN | MCFSLT_SCR_TEN,
134 TA(MCFSLT_SCR));
135 /* initialize mcfslt_cnt knowing that slice timers count down */
136 mcfslt_cnt = mcfslt_cycles_per_jiffy;
137
138 r = request_irq(MCF_IRQ_TIMER, mcfslt_tick, IRQF_TIMER, "timer", NULL);
139 if (r) {
140 pr_err("Failed to request irq %d (timer): %pe\n", MCF_IRQ_TIMER,
141 ERR_PTR(r));
142 }
143
144 clocksource_register_hz(&mcfslt_clk, MCF_BUSCLK);
145
146 #ifdef CONFIG_HIGHPROFILE
147 mcfslt_profile_init();
148 #endif
149 }
150