1 /***************************************************************************/ 2 3 /* 4 * m528x.c -- platform support for ColdFire 528x based boards 5 * 6 * Sub-architcture dependent initialization code for the Freescale 7 * 5280, 5281 and 5282 CPUs. 8 * 9 * Copyright (C) 1999-2003, Greg Ungerer (gerg@snapgear.com) 10 * Copyright (C) 2001-2003, SnapGear Inc. (www.snapgear.com) 11 */ 12 13 /***************************************************************************/ 14 15 #include <linux/kernel.h> 16 #include <linux/param.h> 17 #include <linux/init.h> 18 #include <linux/platform_device.h> 19 #include <linux/io.h> 20 #include <asm/machdep.h> 21 #include <asm/coldfire.h> 22 #include <asm/mcfsim.h> 23 #include <asm/mcfuart.h> 24 #include <asm/mcfclk.h> 25 26 /***************************************************************************/ 27 28 DEFINE_CLK(pll, "pll.0", MCF_CLK); 29 DEFINE_CLK(sys, "sys.0", MCF_BUSCLK); 30 DEFINE_CLK(mcfpit0, "mcfpit.0", MCF_CLK); 31 DEFINE_CLK(mcfpit1, "mcfpit.1", MCF_CLK); 32 DEFINE_CLK(mcfpit2, "mcfpit.2", MCF_CLK); 33 DEFINE_CLK(mcfpit3, "mcfpit.3", MCF_CLK); 34 DEFINE_CLK(mcfuart0, "mcfuart.0", MCF_BUSCLK); 35 DEFINE_CLK(mcfuart1, "mcfuart.1", MCF_BUSCLK); 36 DEFINE_CLK(mcfuart2, "mcfuart.2", MCF_BUSCLK); 37 DEFINE_CLK(mcfqspi0, "mcfqspi.0", MCF_BUSCLK); 38 DEFINE_CLK(fec0, "fec.0", MCF_BUSCLK); 39 40 struct clk *mcf_clks[] = { 41 &clk_pll, 42 &clk_sys, 43 &clk_mcfpit0, 44 &clk_mcfpit1, 45 &clk_mcfpit2, 46 &clk_mcfpit3, 47 &clk_mcfuart0, 48 &clk_mcfuart1, 49 &clk_mcfuart2, 50 &clk_mcfqspi0, 51 &clk_fec0, 52 NULL 53 }; 54 55 /***************************************************************************/ 56 57 static void __init m528x_qspi_init(void) 58 { 59 #if IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI) 60 /* setup Port QS for QSPI with gpio CS control */ 61 __raw_writeb(0x07, MCFGPIO_PQSPAR); 62 #endif /* IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI) */ 63 } 64 65 /***************************************************************************/ 66 67 static void __init m528x_uarts_init(void) 68 { 69 u8 port; 70 71 /* make sure PUAPAR is set for UART0 and UART1 */ 72 port = readb(MCFGPIO_PUAPAR); 73 port |= 0x03 | (0x03 << 2); 74 writeb(port, MCFGPIO_PUAPAR); 75 } 76 77 /***************************************************************************/ 78 79 static void __init m528x_fec_init(void) 80 { 81 u16 v16; 82 83 /* Set multi-function pins to ethernet mode for fec0 */ 84 v16 = readw(MCFGPIO_PASPAR); 85 writew(v16 | 0xf00, MCFGPIO_PASPAR); 86 writeb(0xc0, MCFGPIO_PEHLPAR); 87 } 88 89 /***************************************************************************/ 90 91 #ifdef CONFIG_WILDFIRE 92 void wildfire_halt(void) 93 { 94 writeb(0, 0x30000007); 95 writeb(0x2, 0x30000007); 96 } 97 #endif 98 99 #ifdef CONFIG_WILDFIREMOD 100 void wildfiremod_halt(void) 101 { 102 printk(KERN_INFO "WildFireMod hibernating...\n"); 103 104 /* Set portE.5 to Digital IO */ 105 MCF5282_GPIO_PEPAR &= ~(1 << (5 * 2)); 106 107 /* Make portE.5 an output */ 108 MCF5282_GPIO_DDRE |= (1 << 5); 109 110 /* Now toggle portE.5 from low to high */ 111 MCF5282_GPIO_PORTE &= ~(1 << 5); 112 MCF5282_GPIO_PORTE |= (1 << 5); 113 114 printk(KERN_EMERG "Failed to hibernate. Halting!\n"); 115 } 116 #endif 117 118 void __init config_BSP(char *commandp, int size) 119 { 120 #ifdef CONFIG_WILDFIRE 121 mach_halt = wildfire_halt; 122 #endif 123 #ifdef CONFIG_WILDFIREMOD 124 mach_halt = wildfiremod_halt; 125 #endif 126 mach_sched_init = hw_timer_init; 127 m528x_uarts_init(); 128 m528x_fec_init(); 129 m528x_qspi_init(); 130 } 131 132 /***************************************************************************/ 133