xref: /linux/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts (revision c532de5a67a70f8533d495f8f2aaa9a0491c3ad0) 
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * dts file for Xilinx ZynqMP SM-K26 rev2/1/B/A
4 *
5 * (C) Copyright 2020 - 2021, Xilinx, Inc.
6 * (C) Copyright 2023 - 2024, Advanced Micro Devices, Inc.
7 *
8 * Michal Simek <michal.simek@amd.com>
9 */
10
11/dts-v1/;
12
13#include "zynqmp.dtsi"
14#include "zynqmp-clk-ccf.dtsi"
15#include <dt-bindings/input/input.h>
16#include <dt-bindings/gpio/gpio.h>
17#include <dt-bindings/phy/phy.h>
18#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
19
20/ {
21	model = "ZynqMP SM-K26 Rev2/1/B/A";
22	compatible = "xlnx,zynqmp-sm-k26-rev2",
23		     "xlnx,zynqmp-sm-k26-rev1", "xlnx,zynqmp-sm-k26-revB",
24		     "xlnx,zynqmp-sm-k26-revA", "xlnx,zynqmp-sm-k26",
25		     "xlnx,zynqmp";
26
27	aliases {
28		i2c0 = &i2c0;
29		i2c1 = &i2c1;
30		mmc0 = &sdhci0;
31		mmc1 = &sdhci1;
32		nvmem0 = &eeprom;
33		nvmem1 = &eeprom_cc;
34		rtc0 = &rtc;
35		serial0 = &uart0;
36		serial1 = &uart1;
37		serial2 = &dcc;
38		spi0 = &qspi;
39		spi1 = &spi0;
40		spi2 = &spi1;
41		usb0 = &usb0;
42		usb1 = &usb1;
43	};
44
45	chosen {
46		bootargs = "earlycon";
47		stdout-path = "serial1:115200n8";
48	};
49
50	memory@0 {
51		device_type = "memory"; /* 4GB */
52		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
53	};
54
55	reserved-memory {
56		#address-cells = <2>;
57		#size-cells = <2>;
58		ranges;
59
60		pmu_region: pmu@7ff00000 {
61			reg = <0x0 0x7ff00000 0x0 0x100000>;
62			no-map;
63		};
64	};
65
66	gpio-keys {
67		compatible = "gpio-keys";
68		autorepeat;
69		key-fwuen {
70			label = "fwuen";
71			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
72			linux,code = <BTN_MISC>;
73			wakeup-source;
74			autorepeat;
75		};
76	};
77
78	leds {
79		compatible = "gpio-leds";
80		ds35-led {
81			label = "heartbeat";
82			gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
83			linux,default-trigger = "heartbeat";
84		};
85
86		ds36-led {
87			label = "vbus_det";
88			gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
89			default-state = "on";
90		};
91	};
92
93	ams {
94		compatible = "iio-hwmon";
95		io-channels = <&xilinx_ams 0>, <&xilinx_ams 1>, <&xilinx_ams 2>,
96			<&xilinx_ams 3>, <&xilinx_ams 4>, <&xilinx_ams 5>,
97			<&xilinx_ams 6>, <&xilinx_ams 7>, <&xilinx_ams 8>,
98			<&xilinx_ams 9>, <&xilinx_ams 10>, <&xilinx_ams 11>,
99			<&xilinx_ams 12>, <&xilinx_ams 13>, <&xilinx_ams 14>,
100			<&xilinx_ams 15>, <&xilinx_ams 16>, <&xilinx_ams 17>,
101			<&xilinx_ams 18>, <&xilinx_ams 19>, <&xilinx_ams 20>,
102			<&xilinx_ams 21>, <&xilinx_ams 22>, <&xilinx_ams 23>,
103			<&xilinx_ams 24>, <&xilinx_ams 25>, <&xilinx_ams 26>,
104			<&xilinx_ams 27>, <&xilinx_ams 28>, <&xilinx_ams 29>;
105	};
106
107	pwm-fan {
108		compatible = "pwm-fan";
109		status = "okay";
110		pwms = <&ttc0 2 40000 0>;
111	};
112};
113
114&modepin_gpio {
115	label = "modepin";
116};
117
118&ttc0 {
119	status = "okay";
120	#pwm-cells = <3>;
121};
122
123&uart1 { /* MIO36/MIO37 */
124	status = "okay";
125};
126
127&pinctrl0 {
128	status = "okay";
129	pinctrl_sdhci0_default: sdhci0-default {
130		conf {
131			groups = "sdio0_0_grp";
132			slew-rate = <SLEW_RATE_SLOW>;
133			power-source = <IO_STANDARD_LVCMOS18>;
134			bias-disable;
135		};
136
137		mux {
138			groups = "sdio0_0_grp";
139			function = "sdio0";
140		};
141	};
142};
143
144&qspi { /* MIO 0-5 - U143 */
145	status = "okay";
146	spi_flash: flash@0 { /* MT25QU512A */
147		compatible = "jedec,spi-nor"; /* 64MB */
148		reg = <0>;
149		spi-tx-bus-width = <4>;
150		spi-rx-bus-width = <4>;
151		spi-max-frequency = <40000000>; /* 40MHz */
152
153		partitions {
154			compatible = "fixed-partitions";
155			#address-cells = <1>;
156			#size-cells = <1>;
157
158			partition@0 {
159				label = "Image Selector";
160				reg = <0x0 0x80000>; /* 512KB */
161				read-only;
162				lock;
163			};
164			partition@80000 {
165				label = "Image Selector Golden";
166				reg = <0x80000 0x80000>; /* 512KB */
167				read-only;
168				lock;
169			};
170			partition@100000 {
171				label = "Persistent Register";
172				reg = <0x100000 0x20000>; /* 128KB */
173			};
174			partition@120000 {
175				label = "Persistent Register Backup";
176				reg = <0x120000 0x20000>; /* 128KB */
177			};
178			partition@140000 {
179				label = "Open_1";
180				reg = <0x140000 0xC0000>; /* 768KB */
181			};
182			partition@200000 {
183				label = "Image A (FSBL, PMU, ATF, U-Boot)";
184				reg = <0x200000 0xD00000>; /* 13MB */
185			};
186			partition@f00000 {
187				label = "ImgSel Image A Catch";
188				reg = <0xF00000 0x80000>; /* 512KB */
189				read-only;
190				lock;
191			};
192			partition@f80000 {
193				label = "Image B (FSBL, PMU, ATF, U-Boot)";
194				reg = <0xF80000 0xD00000>; /* 13MB */
195			};
196			partition@1c80000 {
197				label = "ImgSel Image B Catch";
198				reg = <0x1C80000 0x80000>; /* 512KB */
199				read-only;
200				lock;
201			};
202			partition@1d00000 {
203				label = "Open_2";
204				reg = <0x1D00000 0x100000>; /* 1MB */
205			};
206			partition@1e00000 {
207				label = "Recovery Image";
208				reg = <0x1E00000 0x200000>; /* 2MB */
209				read-only;
210				lock;
211			};
212			partition@2000000 {
213				label = "Recovery Image Backup";
214				reg = <0x2000000 0x200000>; /* 2MB */
215				read-only;
216				lock;
217			};
218			partition@2200000 {
219				label = "U-Boot storage variables";
220				reg = <0x2200000 0x20000>; /* 128KB */
221			};
222			partition@2220000 {
223				label = "U-Boot storage variables backup";
224				reg = <0x2220000 0x20000>; /* 128KB */
225			};
226			partition@2240000 {
227				label = "SHA256";
228				reg = <0x2240000 0x40000>; /* 256B but 256KB sector */
229				read-only;
230				lock;
231			};
232			partition@2280000 {
233				label = "Secure OS Storage";
234				reg = <0x2280000 0x20000>; /* 128KB */
235			};
236			partition@22a0000 {
237				label = "User";
238				reg = <0x22a0000 0x1d60000>; /* 29.375 MB */
239			};
240		};
241	};
242};
243
244&sdhci0 { /* MIO13-23 - 16GB emmc MTFC16GAPALBH-IT - U133A */
245	status = "okay";
246	pinctrl-names = "default";
247	pinctrl-0 = <&pinctrl_sdhci0_default>;
248	non-removable;
249	disable-wp;
250	bus-width = <8>;
251	xlnx,mio-bank = <0>;
252	assigned-clock-rates = <187498123>;
253};
254
255&spi1 { /* MIO6, 9-11 */
256	status = "okay";
257	label = "TPM";
258	num-cs = <1>;
259	tpm@0 { /* slm9670 - U144 */
260		compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
261		reg = <0>;
262		spi-max-frequency = <18500000>;
263	};
264};
265
266&i2c1 {
267	status = "okay";
268	bootph-all;
269	clock-frequency = <400000>;
270	scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
271	sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
272
273	eeprom: eeprom@50 { /* u46 - also at address 0x58 */
274		bootph-all;
275		compatible = "st,24c64", "atmel,24c64"; /* st m24c64 */
276		reg = <0x50>;
277		/* WP pin EE_WP_EN connected to slg7x644092@68 */
278	};
279
280	eeprom_cc: eeprom@51 { /* required by spec - also at address 0x59 */
281		bootph-all;
282		compatible = "st,24c64", "atmel,24c64"; /* st m24c64 */
283		reg = <0x51>;
284	};
285
286	/* da9062@30 - u170 - also at address 0x31 */
287	/* da9131@33 - u167 */
288	da9131: pmic@33 {
289		compatible = "dlg,da9131";
290		reg = <0x33>;
291		regulators {
292			da9131_buck1: buck1 {
293				regulator-name = "da9131_buck1";
294				regulator-boot-on;
295				regulator-always-on;
296			};
297			da9131_buck2: buck2 {
298				regulator-name = "da9131_buck2";
299				regulator-boot-on;
300				regulator-always-on;
301			};
302		};
303	};
304
305	/* da9130@32 - u166 */
306	da9130: pmic@32 {
307		compatible = "dlg,da9130";
308		reg = <0x32>;
309		regulators {
310			da9130_buck1: buck1 {
311				regulator-name = "da9130_buck1";
312				regulator-boot-on;
313				regulator-always-on;
314			};
315		};
316	};
317
318	/* slg7x644091@70 - u168 NOT accessible due to address conflict with stdp4320 */
319	/*
320	 * stdp4320 - u27 FW has below two issues to be fixed in next board revision.
321	 * Device acknowledging to addresses 0x5C, 0x5D, 0x70, 0x72, 0x76.
322	 * Address conflict with slg7x644091@70 making both the devices NOT accessible.
323	 * With the FW fix, stdp4320 should respond to address 0x73 only.
324	 */
325	/* slg7x644092@68 - u169 */
326	/* Also connected via JA1C as C23/C24 */
327};
328
329&gpio {
330	status = "okay";
331	gpio-line-names = "QSPI_CLK", "QSPI_DQ1", "QSPI_DQ2", "QSPI_DQ3", "QSPI_DQ0", /* 0 - 4 */
332			  "QSPI_CS_B", "SPI_CLK", "LED1", "LED2", "SPI_CS_B", /* 5 - 9 */
333			  "SPI_MISO", "SPI_MOSI", "FWUEN", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
334			  "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
335			  "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST", "I2C1_SCL", /* 20 - 24 */
336			  "I2C1_SDA", "", "", "", "", /* 25 - 29 */
337			  "", "", "", "", "", /* 30 - 34 */
338			  "", "", "", "", "", /* 35 - 39 */
339			  "", "", "", "", "", /* 40 - 44 */
340			  "", "", "", "", "", /* 45 - 49 */
341			  "", "", "", "", "", /* 50 - 54 */
342			  "", "", "", "", "", /* 55 - 59 */
343			  "", "", "", "", "", /* 60 - 64 */
344			  "", "", "", "", "", /* 65 - 69 */
345			  "", "", "", "", "", /* 70 - 74 */
346			  "", "", "", /* 75 - 77, MIO end and EMIO start */
347			  "", "", /* 78 - 79 */
348			  "", "", "", "", "", /* 80 - 84 */
349			  "", "", "", "", "", /* 85 - 89 */
350			  "", "", "", "", "", /* 90 - 94 */
351			  "", "", "", "", "", /* 95 - 99 */
352			  "", "", "", "", "", /* 100 - 104 */
353			  "", "", "", "", "", /* 105 - 109 */
354			  "", "", "", "", "", /* 110 - 114 */
355			  "", "", "", "", "", /* 115 - 119 */
356			  "", "", "", "", "", /* 120 - 124 */
357			  "", "", "", "", "", /* 125 - 129 */
358			  "", "", "", "", "", /* 130 - 134 */
359			  "", "", "", "", "", /* 135 - 139 */
360			  "", "", "", "", "", /* 140 - 144 */
361			  "", "", "", "", "", /* 145 - 149 */
362			  "", "", "", "", "", /* 150 - 154 */
363			  "", "", "", "", "", /* 155 - 159 */
364			  "", "", "", "", "", /* 160 - 164 */
365			  "", "", "", "", "", /* 165 - 169 */
366			  "", "", "", ""; /* 170 - 173 */
367};
368
369&xilinx_ams {
370	status = "okay";
371};
372
373&ams_ps {
374	status = "okay";
375};
376
377&ams_pl {
378	status = "okay";
379};
380
381&zynqmp_dpsub {
382	status = "okay";
383};
384
385&rtc {
386	status = "okay";
387};
388
389&lpd_dma_chan1 {
390	status = "okay";
391};
392
393&lpd_dma_chan2 {
394	status = "okay";
395};
396
397&lpd_dma_chan3 {
398	status = "okay";
399};
400
401&lpd_dma_chan4 {
402	status = "okay";
403};
404
405&lpd_dma_chan5 {
406	status = "okay";
407};
408
409&lpd_dma_chan6 {
410	status = "okay";
411};
412
413&lpd_dma_chan7 {
414	status = "okay";
415};
416
417&lpd_dma_chan8 {
418	status = "okay";
419};
420
421&fpd_dma_chan1 {
422	status = "okay";
423};
424
425&fpd_dma_chan2 {
426	status = "okay";
427};
428
429&fpd_dma_chan3 {
430	status = "okay";
431};
432
433&fpd_dma_chan4 {
434	status = "okay";
435};
436
437&fpd_dma_chan5 {
438	status = "okay";
439};
440
441&fpd_dma_chan6 {
442	status = "okay";
443};
444
445&fpd_dma_chan7 {
446	status = "okay";
447};
448
449&fpd_dma_chan8 {
450	status = "okay";
451};
452
453&gpu {
454	status = "okay";
455};
456
457&lpd_watchdog {
458	status = "okay";
459};
460
461&watchdog0 {
462	status = "okay";
463};
464
465&cpu_opp_table {
466	opp00 {
467		opp-hz = /bits/ 64 <1333333333>;
468	};
469	opp01 {
470		opp-hz = /bits/ 64 <666666666>;
471	};
472	opp02 {
473		opp-hz = /bits/ 64 <444444444>;
474	};
475	opp03 {
476		opp-hz = /bits/ 64 <333333333>;
477	};
478};
479