1// SPDX-License-Identifier: (GPL-2.0+ OR MIT) 2 3/dts-v1/; 4 5#include <dt-bindings/gpio/gpio.h> 6#include <dt-bindings/input/linux-event-codes.h> 7#include <dt-bindings/pinctrl/rockchip.h> 8#include <dt-bindings/usb/pd.h> 9#include "rk3588s.dtsi" 10 11/ { 12 model = "Indiedroid Nova"; 13 compatible = "indiedroid,nova", "rockchip,rk3588s"; 14 15 adc-keys-0 { 16 compatible = "adc-keys"; 17 io-channel-names = "buttons"; 18 io-channels = <&saradc 0>; 19 keyup-threshold-microvolt = <1800000>; 20 poll-interval = <100>; 21 22 button-boot { 23 label = "boot"; 24 linux,code = <KEY_PROG1>; 25 press-threshold-microvolt = <18000>; 26 }; 27 }; 28 29 adc-keys-1 { 30 compatible = "adc-keys"; 31 io-channel-names = "buttons"; 32 io-channels = <&saradc 1>; 33 keyup-threshold-microvolt = <1800000>; 34 poll-interval = <100>; 35 36 button-recovery { 37 label = "recovery"; 38 linux,code = <KEY_PROG2>; 39 press-threshold-microvolt = <18000>; 40 }; 41 }; 42 43 aliases { 44 mmc0 = &sdhci; 45 mmc1 = &sdmmc; 46 mmc2 = &sdio; 47 }; 48 49 chosen { 50 stdout-path = "serial2:1500000n8"; 51 }; 52 53 sdio_pwrseq: sdio-pwrseq { 54 compatible = "mmc-pwrseq-simple"; 55 clock-names = "ext_clock"; 56 clocks = <&rtc_hym8563>; 57 pinctrl-0 = <&wifi_enable_h>; 58 pinctrl-names = "default"; 59 post-power-on-delay-ms = <200>; 60 reset-gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_LOW>; 61 }; 62 63 sound { 64 compatible = "audio-graph-card"; 65 label = "rockchip,es8388-codec"; 66 widgets = "Microphone", "Mic Jack", 67 "Headphone", "Headphones"; 68 routing = "LINPUT2", "Mic Jack", 69 "Headphones", "LOUT1", 70 "Headphones", "ROUT1"; 71 dais = <&i2s0_8ch_p0>; 72 }; 73 74 vbus5v0_typec: vbus5v0-typec-regulator { 75 compatible = "regulator-fixed"; 76 enable-active-high; 77 gpio = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>; 78 pinctrl-0 = <&typec5v_pwren>; 79 pinctrl-names = "default"; 80 regulator-name = "vbus5v0_typec"; 81 regulator-min-microvolt = <5000000>; 82 regulator-max-microvolt = <5000000>; 83 vin-supply = <&vcc5v0_usb>; 84 }; 85 86 vcc_1v1_nldo_s3: vcc-1v1-nldo-s3-regulator { 87 compatible = "regulator-fixed"; 88 regulator-always-on; 89 regulator-boot-on; 90 regulator-max-microvolt = <1100000>; 91 regulator-min-microvolt = <1100000>; 92 regulator-name = "vcc_1v1_nldo_s3"; 93 vin-supply = <&vcc5v0_sys>; 94 }; 95 96 /* Regulator is enabled whenever vcc_1v8_s0 is above 1.6v */ 97 vcc_3v3_s0: vcc-3v3-s0-regulator { 98 compatible = "regulator-fixed"; 99 regulator-always-on; 100 regulator-boot-on; 101 regulator-max-microvolt = <3300000>; 102 regulator-min-microvolt = <3300000>; 103 regulator-name = "vcc_3v3_s0"; 104 vin-supply = <&vcc_3v3_s3>; 105 106 regulator-state-mem { 107 regulator-off-in-suspend; 108 }; 109 }; 110 111 vcc5v0_sys: vcc5v0-sys-regulator { 112 compatible = "regulator-fixed"; 113 regulator-always-on; 114 regulator-boot-on; 115 regulator-max-microvolt = <5000000>; 116 regulator-min-microvolt = <5000000>; 117 regulator-name = "vcc5v0_sys"; 118 }; 119 120 vcc5v0_usb: vcc5v0-usb-regulator { 121 compatible = "regulator-fixed"; 122 regulator-always-on; 123 regulator-boot-on; 124 regulator-max-microvolt = <5000000>; 125 regulator-min-microvolt = <5000000>; 126 regulator-name = "vcc5v0_usb"; 127 vin-supply = <&vcc5v0_usbdcin>; 128 }; 129 130 vcc5v0_usbdcin: vcc5v0-usbdcin-regulator { 131 compatible = "regulator-fixed"; 132 regulator-always-on; 133 regulator-boot-on; 134 regulator-max-microvolt = <5000000>; 135 regulator-min-microvolt = <5000000>; 136 regulator-name = "vcc5v0_usbdcin"; 137 }; 138}; 139 140&combphy0_ps { 141 status = "okay"; 142}; 143 144&combphy2_psu { 145 status = "okay"; 146}; 147 148&cpu_l0 { 149 cpu-supply = <&vdd_cpu_lit_s0>; 150}; 151 152&cpu_l1 { 153 cpu-supply = <&vdd_cpu_lit_s0>; 154}; 155 156&cpu_l2 { 157 cpu-supply = <&vdd_cpu_lit_s0>; 158}; 159 160&cpu_l3 { 161 cpu-supply = <&vdd_cpu_lit_s0>; 162}; 163 164&cpu_b0 { 165 cpu-supply = <&vdd_cpu_big0_s0>; 166}; 167 168&cpu_b1 { 169 cpu-supply = <&vdd_cpu_big0_s0>; 170}; 171 172&cpu_b2 { 173 cpu-supply = <&vdd_cpu_big1_s0>; 174}; 175 176&cpu_b3 { 177 cpu-supply = <&vdd_cpu_big1_s0>; 178}; 179 180/* 181 * Add labels for each GPIO pin exposed on the 40 pin header. Note that 182 * voltage of each GPIO pin could be either 3.3v or 1.8v (as noted by 183 * label). 184 */ 185&gpio0 { 186 gpio-line-names = /* GPIO0 A0-A7 */ 187 "", "", "", "", 188 "", "", "", "", 189 /* GPIO0 B0-B7 */ 190 "", "", "", "", 191 "", "", "", "", 192 /* GPIO0 C0-C7 */ 193 "", "", "", "", 194 "", "", "", "", 195 /* GPIO0 D0-D7 */ 196 "HEADER_12_1v8", "", "", "HEADER_24_1v8", 197 "", "", "", ""; 198}; 199 200&gpio1 { 201 gpio-line-names = /* GPIO1 A0-A7 */ 202 "HEADER_27_3v3", "", "", "", 203 "HEADER_29_1v8", "", "HEADER_7_1v8", "", 204 /* GPIO1 B0-B7 */ 205 "", "HEADER_31_1v8", "HEADER_33_1v8", "", 206 "HEADER_11_1v8", "HEADER_13_1v8", "", "", 207 /* GPIO1 C0-C7 */ 208 "", "HEADER_28_3v3", "", "", 209 "", "", "", "", 210 /* GPIO1 D0-D7 */ 211 "", "", "", "", 212 "", "", "HEADER_5_3v3", "HEADER_3_3v3"; 213}; 214 215&gpio3 { 216 gpio-line-names = /* GPIO3 A0-A7 */ 217 "", "", "", "", 218 "", "", "", "", 219 /* GPIO3 B0-B7 */ 220 "HEADER_16_1v8", "HEADER_18_1v8", "", "", 221 "", "", "", "HEADER_19_1v8", 222 /* GPIO3 C0-C7 */ 223 "HEADER_21_1v8", "HEADER_23_1v8", "", "HEADER_26_1v8", 224 "HEADER_15_1v8", "HEADER_22_1v8", "", "", 225 /* GPIO3 D0-D7 */ 226 "", "", "", "", 227 "", "", "", ""; 228}; 229 230&gpio4 { 231 gpio-line-names = /* GPIO4 A0-A7 */ 232 "", "", "HEADER_37_3v3", "HEADER_8_3v3", 233 "HEADER_10_3v3", "", "HEADER_32_3v3", "HEADER_35_3v3", 234 /* GPIO4 B0-B7 */ 235 "", "", "", "HEADER_40_3v3", 236 "HEADER_38_3v3", "HEADER_36_3v3", "", "", 237 /* GPIO4 C0-C7 */ 238 "", "", "", "", 239 "", "", "", "", 240 /* GPIO4 D0-D7 */ 241 "", "", "", "", 242 "", "", "", ""; 243}; 244 245&i2c0 { 246 pinctrl-0 = <&i2c0m2_xfer>; 247 pinctrl-names = "default"; 248 status = "okay"; 249 250 vdd_cpu_big0_s0: regulator@42 { 251 compatible = "rockchip,rk8602"; 252 reg = <0x42>; 253 regulator-always-on; 254 regulator-boot-on; 255 regulator-max-microvolt = <1050000>; 256 regulator-min-microvolt = <550000>; 257 regulator-name = "vdd_cpu_big0_s0"; 258 regulator-ramp-delay = <2300>; 259 fcs,suspend-voltage-selector = <1>; 260 vin-supply = <&vcc5v0_sys>; 261 262 regulator-state-mem { 263 regulator-off-in-suspend; 264 }; 265 }; 266 267 vdd_cpu_big1_s0: regulator@43 { 268 compatible = "rockchip,rk8603", "rockchip,rk8602"; 269 reg = <0x43>; 270 regulator-always-on; 271 regulator-boot-on; 272 regulator-max-microvolt = <1050000>; 273 regulator-min-microvolt = <550000>; 274 regulator-name = "vdd_cpu_big1_s0"; 275 regulator-ramp-delay = <2300>; 276 fcs,suspend-voltage-selector = <1>; 277 vin-supply = <&vcc5v0_sys>; 278 279 regulator-state-mem { 280 regulator-off-in-suspend; 281 }; 282 }; 283}; 284 285&i2c2 { 286 status = "okay"; 287 288 vdd_npu_s0: regulator@42 { 289 compatible = "rockchip,rk8602"; 290 reg = <0x42>; 291 regulator-always-on; 292 regulator-boot-on; 293 regulator-max-microvolt = <950000>; 294 regulator-min-microvolt = <550000>; 295 regulator-name = "vdd_npu_s0"; 296 regulator-ramp-delay = <2300>; 297 fcs,suspend-voltage-selector = <1>; 298 vin-supply = <&vcc5v0_sys>; 299 300 regulator-state-mem { 301 regulator-off-in-suspend; 302 }; 303 }; 304}; 305 306&i2c6 { 307 pinctrl-0 = <&i2c6m3_xfer>; 308 status = "okay"; 309 310 fusb302: typec-portc@22 { 311 compatible = "fcs,fusb302"; 312 reg = <0x22>; 313 interrupt-parent = <&gpio0>; 314 interrupts = <RK_PC4 IRQ_TYPE_LEVEL_LOW>; 315 pinctrl-0 = <&usbc0_int>; 316 pinctrl-names = "default"; 317 vbus-supply = <&vbus5v0_typec>; 318 319 connector { 320 compatible = "usb-c-connector"; 321 data-role = "dual"; 322 label = "USB-C"; 323 power-role = "dual"; 324 try-power-role = "sink"; 325 source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; 326 sink-pdos = <PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>; 327 op-sink-microwatt = <1000000>; 328 }; 329 }; 330 331 rtc_hym8563: rtc@51 { 332 compatible = "haoyu,hym8563"; 333 reg = <0x51>; 334 #clock-cells = <0>; 335 clock-output-names = "hym8563"; 336 interrupt-parent = <&gpio0>; 337 interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>; 338 pinctrl-0 = <&hym8563_int>; 339 pinctrl-names = "default"; 340 wakeup-source; 341 }; 342}; 343 344&i2c7 { 345 pinctrl-0 = <&i2c7m0_xfer>; 346 status = "okay"; 347 348 es8388: audio-codec@11 { 349 compatible = "everest,es8388"; 350 reg = <0x11>; 351 assigned-clock-rates = <12288000>; 352 assigned-clocks = <&cru I2S0_8CH_MCLKOUT>; 353 AVDD-supply = <&vcc_3v3_s3>; 354 clock-names = "mclk"; 355 clocks = <&cru I2S0_8CH_MCLKOUT>; 356 DVDD-supply = <&vcc_1v8_s3>; 357 HPVDD-supply = <&vcc_3v3_s3>; 358 PVDD-supply = <&vcc_1v8_s3>; 359 #sound-dai-cells = <0>; 360 361 port { 362 es8388_p0_0: endpoint { 363 remote-endpoint = <&i2s0_8ch_p0_0>; 364 }; 365 }; 366 }; 367}; 368 369&i2s0_8ch { 370 pinctrl-names = "default"; 371 pinctrl-0 = <&i2s0_lrck 372 &i2s0_mclk 373 &i2s0_sclk 374 &i2s0_sdi0 375 &i2s0_sdo0>; 376 status = "okay"; 377 378 i2s0_8ch_p0: port { 379 i2s0_8ch_p0_0: endpoint { 380 dai-format = "i2s"; 381 mclk-fs = <256>; 382 remote-endpoint = <&es8388_p0_0>; 383 }; 384 }; 385}; 386 387&pcie2x1l2 { 388 pinctrl-0 = <&rtl8111_perstb>; 389 pinctrl-names = "default"; 390 status = "okay"; 391}; 392 393&pinctrl { 394 bluetooth-pins { 395 bt_reset: bt-reset { 396 rockchip,pins = 397 <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>; 398 }; 399 400 bt_wake_dev: bt-wake-dev { 401 rockchip,pins = 402 <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; 403 }; 404 405 bt_wake_host: bt-wake-host { 406 rockchip,pins = 407 <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_down>; 408 }; 409 }; 410 411 ethernet-pins { 412 rtl8111_perstb: rtl8111-perstb { 413 rockchip,pins = <3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_up>; 414 }; 415 }; 416 417 hym8563 { 418 419 hym8563_int: hym8563-int { 420 rockchip,pins = 421 <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>; 422 }; 423 }; 424 425 sdio-pwrseq { 426 wifi_enable_h: wifi-enable-h { 427 rockchip,pins = 428 <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>; 429 }; 430 }; 431 432 usb-typec { 433 usbc0_int: usbc0-int { 434 rockchip,pins = 435 <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_up>; 436 }; 437 438 typec5v_pwren: typec5v-pwren { 439 rockchip,pins = 440 <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; 441 }; 442 }; 443}; 444 445&saradc { 446 vref-supply = <&vcca_1v8_s0>; 447 status = "okay"; 448}; 449 450/* HS400 modes seemed to cause io errors. */ 451&sdhci { 452 bus-width = <8>; 453 no-mmc-hs400; 454 no-sd; 455 no-sdio; 456 non-removable; 457 vmmc-supply = <&vcc_3v3_s0>; 458 vqmmc-supply = <&vcc_1v8_s3>; 459 status = "okay"; 460}; 461 462&sdio { 463 bus-width = <4>; 464 cap-sd-highspeed; 465 cap-sdio-irq; 466 disable-wp; 467 keep-power-in-suspend; 468 max-frequency = <100000000>; 469 mmc-pwrseq = <&sdio_pwrseq>; 470 no-mmc; 471 no-sd; 472 non-removable; 473 sd-uhs-sdr104; 474 vmmc-supply = <&vcc_3v3_s3>; 475 vqmmc-supply = <&vcc_1v8_s3>; 476 status = "okay"; 477}; 478 479&sdmmc { 480 bus-width = <4>; 481 cap-mmc-highspeed; 482 cap-sd-highspeed; 483 disable-wp; 484 no-sdio; 485 no-mmc; 486 sd-uhs-sdr104; 487 vmmc-supply = <&vcc_3v3_s3>; 488 vqmmc-supply = <&vccio_sd_s0>; 489 status = "okay"; 490}; 491 492&spi2 { 493 #address-cells = <1>; 494 assigned-clocks = <&cru CLK_SPI2>; 495 assigned-clock-rates = <200000000>; 496 num-cs = <1>; 497 pinctrl-0 = <&spi2m2_pins>, <&spi2m2_cs0>; 498 pinctrl-names = "default"; 499 #size-cells = <0>; 500 status = "okay"; 501 502 pmic@0 { 503 compatible = "rockchip,rk806"; 504 reg = <0x0>; 505 #gpio-cells = <2>; 506 gpio-controller; 507 interrupt-parent = <&gpio0>; 508 interrupts = <RK_PA7 IRQ_TYPE_LEVEL_LOW>; 509 pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>, 510 <&rk806_dvs2_null>, <&rk806_dvs3_null>; 511 pinctrl-names = "default"; 512 spi-max-frequency = <1000000>; 513 514 vcc1-supply = <&vcc5v0_sys>; 515 vcc2-supply = <&vcc5v0_sys>; 516 vcc3-supply = <&vcc5v0_sys>; 517 vcc4-supply = <&vcc5v0_sys>; 518 vcc5-supply = <&vcc5v0_sys>; 519 vcc6-supply = <&vcc5v0_sys>; 520 vcc7-supply = <&vcc5v0_sys>; 521 vcc8-supply = <&vcc5v0_sys>; 522 vcc9-supply = <&vcc5v0_sys>; 523 vcc10-supply = <&vcc5v0_sys>; 524 vcc11-supply = <&vcc_2v0_pldo_s3>; 525 vcc12-supply = <&vcc5v0_sys>; 526 vcc13-supply = <&vcc_1v1_nldo_s3>; 527 vcc14-supply = <&vcc_1v1_nldo_s3>; 528 vcca-supply = <&vcc5v0_sys>; 529 530 rk806_dvs1_null: dvs1-null-pins { 531 pins = "gpio_pwrctrl2"; 532 function = "pin_fun0"; 533 }; 534 535 rk806_dvs2_null: dvs2-null-pins { 536 pins = "gpio_pwrctrl2"; 537 function = "pin_fun0"; 538 }; 539 540 rk806_dvs3_null: dvs3-null-pins { 541 pins = "gpio_pwrctrl3"; 542 function = "pin_fun0"; 543 }; 544 545 regulators { 546 vdd_gpu_s0: dcdc-reg1 { 547 regulator-boot-on; 548 regulator-enable-ramp-delay = <400>; 549 regulator-max-microvolt = <950000>; 550 regulator-min-microvolt = <550000>; 551 regulator-name = "vdd_gpu_s0"; 552 regulator-ramp-delay = <12500>; 553 regulator-state-mem { 554 regulator-off-in-suspend; 555 }; 556 }; 557 558 vdd_cpu_lit_s0: dcdc-reg2 { 559 regulator-always-on; 560 regulator-boot-on; 561 regulator-max-microvolt = <950000>; 562 regulator-min-microvolt = <550000>; 563 regulator-ramp-delay = <12500>; 564 regulator-name = "vdd_cpu_lit_s0"; 565 regulator-state-mem { 566 regulator-off-in-suspend; 567 }; 568 }; 569 570 vdd_logic_s0: dcdc-reg3 { 571 regulator-always-on; 572 regulator-boot-on; 573 regulator-max-microvolt = <750000>; 574 regulator-min-microvolt = <675000>; 575 regulator-name = "vdd_logic_s0"; 576 regulator-ramp-delay = <12500>; 577 regulator-state-mem { 578 regulator-on-in-suspend; 579 regulator-suspend-microvolt = <750000>; 580 }; 581 }; 582 583 vdd_vdenc_s0: dcdc-reg4 { 584 regulator-always-on; 585 regulator-boot-on; 586 regulator-max-microvolt = <950000>; 587 regulator-min-microvolt = <550000>; 588 regulator-name = "vdd_vdenc_s0"; 589 regulator-ramp-delay = <12500>; 590 regulator-state-mem { 591 regulator-off-in-suspend; 592 }; 593 }; 594 595 vdd_ddr_s0: dcdc-reg5 { 596 regulator-always-on; 597 regulator-boot-on; 598 regulator-min-microvolt = <750000>; 599 regulator-max-microvolt = <850000>; 600 regulator-ramp-delay = <12500>; 601 regulator-name = "vdd_ddr_s0"; 602 regulator-state-mem { 603 regulator-off-in-suspend; 604 regulator-suspend-microvolt = <850000>; 605 }; 606 }; 607 608 vdd2_ddr_s3: dcdc-reg6 { 609 regulator-always-on; 610 regulator-boot-on; 611 regulator-max-microvolt = <1100000>; 612 regulator-min-microvolt = <1100000>; 613 regulator-name = "vdd2_ddr_s3"; 614 regulator-state-mem { 615 regulator-on-in-suspend; 616 }; 617 }; 618 619 vcc_2v0_pldo_s3: dcdc-reg7 { 620 regulator-always-on; 621 regulator-boot-on; 622 regulator-max-microvolt = <2000000>; 623 regulator-min-microvolt = <2000000>; 624 regulator-name = "vdd_2v0_pldo_s3"; 625 regulator-state-mem { 626 regulator-on-in-suspend; 627 regulator-suspend-microvolt = <2000000>; 628 }; 629 }; 630 631 vcc_3v3_s3: dcdc-reg8 { 632 regulator-always-on; 633 regulator-boot-on; 634 regulator-max-microvolt = <3300000>; 635 regulator-min-microvolt = <3300000>; 636 regulator-name = "vcc_3v3_s3"; 637 regulator-state-mem { 638 regulator-on-in-suspend; 639 regulator-suspend-microvolt = <3300000>; 640 }; 641 }; 642 643 vddq_ddr_s0: dcdc-reg9 { 644 regulator-always-on; 645 regulator-boot-on; 646 regulator-max-microvolt = <600000>; 647 regulator-min-microvolt = <600000>; 648 regulator-name = "vddq_ddr_s0"; 649 regulator-state-mem { 650 regulator-off-in-suspend; 651 }; 652 }; 653 654 vcc_1v8_s3: dcdc-reg10 { 655 regulator-always-on; 656 regulator-boot-on; 657 regulator-max-microvolt = <1800000>; 658 regulator-min-microvolt = <1800000>; 659 regulator-name = "vcc_1v8_s3"; 660 regulator-state-mem { 661 regulator-on-in-suspend; 662 regulator-suspend-microvolt = <1800000>; 663 }; 664 }; 665 666 vcc_1v8_s0: pldo-reg1 { 667 regulator-always-on; 668 regulator-boot-on; 669 regulator-max-microvolt = <1800000>; 670 regulator-min-microvolt = <1800000>; 671 regulator-name = "vcc_1v8_s0"; 672 regulator-state-mem { 673 regulator-off-in-suspend; 674 }; 675 }; 676 677 vcca_1v8_s0: pldo-reg2 { 678 regulator-always-on; 679 regulator-boot-on; 680 regulator-max-microvolt = <1800000>; 681 regulator-min-microvolt = <1800000>; 682 regulator-name = "vcca_1v8_s0"; 683 regulator-state-mem { 684 regulator-off-in-suspend; 685 regulator-suspend-microvolt = <1800000>; 686 }; 687 }; 688 689 vdda_1v2_s0: pldo-reg3 { 690 regulator-always-on; 691 regulator-boot-on; 692 regulator-max-microvolt = <1200000>; 693 regulator-min-microvolt = <1200000>; 694 regulator-name = "vdda_1v2_s0"; 695 regulator-state-mem { 696 regulator-off-in-suspend; 697 }; 698 }; 699 700 vcca_3v3_s0: pldo-reg4 { 701 regulator-always-on; 702 regulator-boot-on; 703 regulator-max-microvolt = <3300000>; 704 regulator-min-microvolt = <3300000>; 705 regulator-name = "vcca_3v3_s0"; 706 regulator-state-mem { 707 regulator-off-in-suspend; 708 }; 709 }; 710 711 vccio_sd_s0: pldo-reg5 { 712 regulator-always-on; 713 regulator-boot-on; 714 regulator-max-microvolt = <3300000>; 715 regulator-min-microvolt = <1800000>; 716 regulator-name = "vccio_sd_s0"; 717 regulator-state-mem { 718 regulator-off-in-suspend; 719 }; 720 }; 721 722 vcc_1v8_s3_pldo6: pldo-reg6 { 723 regulator-always-on; 724 regulator-boot-on; 725 regulator-max-microvolt = <1800000>; 726 regulator-min-microvolt = <1800000>; 727 regulator-name = "vcc_1v8_s3_pldo6"; 728 regulator-state-mem { 729 regulator-on-in-suspend; 730 regulator-suspend-microvolt = <1800000>; 731 }; 732 }; 733 734 vdd_0v75_s3: nldo-reg1 { 735 regulator-always-on; 736 regulator-boot-on; 737 regulator-max-microvolt = <750000>; 738 regulator-min-microvolt = <750000>; 739 regulator-name = "vdd_0v75_s3"; 740 regulator-state-mem { 741 regulator-on-in-suspend; 742 regulator-suspend-microvolt = <750000>; 743 }; 744 }; 745 746 vdda_ddr_pll_s0: nldo-reg2 { 747 regulator-always-on; 748 regulator-boot-on; 749 regulator-max-microvolt = <850000>; 750 regulator-min-microvolt = <850000>; 751 regulator-name = "vdda_ddr_pll_s0"; 752 regulator-state-mem { 753 regulator-off-in-suspend; 754 regulator-suspend-microvolt = <850000>; 755 }; 756 }; 757 758 avdd_0v75_s0: nldo-reg3 { 759 regulator-always-on; 760 regulator-boot-on; 761 regulator-max-microvolt = <750000>; 762 regulator-min-microvolt = <750000>; 763 regulator-name = "avdd_0v75_s0"; 764 regulator-state-mem { 765 regulator-off-in-suspend; 766 }; 767 }; 768 769 vdda_0v85_s0: nldo-reg4 { 770 regulator-always-on; 771 regulator-boot-on; 772 regulator-min-microvolt = <850000>; 773 regulator-max-microvolt = <850000>; 774 regulator-name = "vdda_0v85_s0"; 775 regulator-state-mem { 776 regulator-off-in-suspend; 777 }; 778 }; 779 780 /* Schematics show not in use */ 781 nldo-reg5 { 782 }; 783 }; 784 }; 785}; 786 787&tsadc { 788 status = "okay"; 789}; 790 791&u2phy2 { 792 status = "okay"; 793}; 794 795&u2phy2_host { 796 phy-supply = <&vcc5v0_usb>; 797 status = "okay"; 798}; 799 800&u2phy3 { 801 status = "okay"; 802}; 803 804&u2phy3_host { 805 phy-supply = <&vcc5v0_usb>; 806 status = "okay"; 807}; 808 809&uart2 { 810 pinctrl-0 = <&uart2m0_xfer>; 811 status = "okay"; 812}; 813 814/* DMA seems to interfere with bluetooth device normal operation. */ 815&uart9 { 816 pinctrl-0 = <&uart9m2_xfer>, <&uart9m2_ctsn>, <&uart9m2_rtsn>; 817 pinctrl-names = "default"; 818 /delete-property/ dma-names; 819 /delete-property/ dmas; 820 uart-has-rtscts; 821 status = "okay"; 822 823 bluetooth { 824 compatible = "realtek,rtl8821cs-bt", 825 "realtek,rtl8723bs-bt"; 826 device-wake-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>; 827 enable-gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>; 828 host-wake-gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>; 829 pinctrl-0 = <&bt_reset>, <&bt_wake_dev>, <&bt_wake_host>; 830 pinctrl-names = "default"; 831 }; 832}; 833 834&usb_host0_ehci { 835 status = "okay"; 836}; 837 838&usb_host0_ohci { 839 status = "okay"; 840}; 841 842&usb_host1_ehci { 843 status = "okay"; 844}; 845 846&usb_host1_ohci { 847 status = "okay"; 848}; 849 850&usb_host2_xhci { 851 status = "okay"; 852}; 853