xref: /linux/arch/arm64/boot/dts/rockchip/rk3588.dtsi (revision 90d32e92011eaae8e70a9169b4e7acf4ca8f9d3a)
1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2/*
3 * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
4 */
5
6#include "rk3588s.dtsi"
7#include "rk3588-pinctrl.dtsi"
8
9/ {
10	usb_host1_xhci: usb@fc400000 {
11		compatible = "rockchip,rk3588-dwc3", "snps,dwc3";
12		reg = <0x0 0xfc400000 0x0 0x400000>;
13		interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH 0>;
14		clocks = <&cru REF_CLK_USB3OTG1>, <&cru SUSPEND_CLK_USB3OTG1>,
15			 <&cru ACLK_USB3OTG1>;
16		clock-names = "ref_clk", "suspend_clk", "bus_clk";
17		dr_mode = "otg";
18		phys = <&u2phy1_otg>, <&usbdp_phy1 PHY_TYPE_USB3>;
19		phy-names = "usb2-phy", "usb3-phy";
20		phy_type = "utmi_wide";
21		power-domains = <&power RK3588_PD_USB>;
22		resets = <&cru SRST_A_USB3OTG1>;
23		snps,dis_enblslpm_quirk;
24		snps,dis-u2-freeclk-exists-quirk;
25		snps,dis-del-phy-power-chg-quirk;
26		snps,dis-tx-ipgap-linecheck-quirk;
27		status = "disabled";
28	};
29
30	pcie30_phy_grf: syscon@fd5b8000 {
31		compatible = "rockchip,rk3588-pcie3-phy-grf", "syscon";
32		reg = <0x0 0xfd5b8000 0x0 0x10000>;
33	};
34
35	pipe_phy1_grf: syscon@fd5c0000 {
36		compatible = "rockchip,rk3588-pipe-phy-grf", "syscon";
37		reg = <0x0 0xfd5c0000 0x0 0x100>;
38	};
39
40	usbdpphy1_grf: syscon@fd5cc000 {
41		compatible = "rockchip,rk3588-usbdpphy-grf", "syscon";
42		reg = <0x0 0xfd5cc000 0x0 0x4000>;
43	};
44
45	usb2phy1_grf: syscon@fd5d4000 {
46		compatible = "rockchip,rk3588-usb2phy-grf", "syscon", "simple-mfd";
47		reg = <0x0 0xfd5d4000 0x0 0x4000>;
48		#address-cells = <1>;
49		#size-cells = <1>;
50
51		u2phy1: usb2phy@4000 {
52			compatible = "rockchip,rk3588-usb2phy";
53			reg = <0x4000 0x10>;
54			#clock-cells = <0>;
55			clocks = <&cru CLK_USB2PHY_HDPTXRXPHY_REF>;
56			clock-names = "phyclk";
57			clock-output-names = "usb480m_phy1";
58			interrupts = <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH 0>;
59			resets = <&cru SRST_OTGPHY_U3_1>, <&cru SRST_P_USB2PHY_U3_1_GRF0>;
60			reset-names = "phy", "apb";
61			status = "disabled";
62
63			u2phy1_otg: otg-port {
64				#phy-cells = <0>;
65				status = "disabled";
66			};
67		};
68	};
69
70	i2s8_8ch: i2s@fddc8000 {
71		compatible = "rockchip,rk3588-i2s-tdm";
72		reg = <0x0 0xfddc8000 0x0 0x1000>;
73		interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH 0>;
74		clocks = <&cru MCLK_I2S8_8CH_TX>, <&cru MCLK_I2S8_8CH_TX>, <&cru HCLK_I2S8_8CH>;
75		clock-names = "mclk_tx", "mclk_rx", "hclk";
76		assigned-clocks = <&cru CLK_I2S8_8CH_TX_SRC>;
77		assigned-clock-parents = <&cru PLL_AUPLL>;
78		dmas = <&dmac2 22>;
79		dma-names = "tx";
80		power-domains = <&power RK3588_PD_VO0>;
81		resets = <&cru SRST_M_I2S8_8CH_TX>;
82		reset-names = "tx-m";
83		#sound-dai-cells = <0>;
84		status = "disabled";
85	};
86
87	i2s6_8ch: i2s@fddf4000 {
88		compatible = "rockchip,rk3588-i2s-tdm";
89		reg = <0x0 0xfddf4000 0x0 0x1000>;
90		interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH 0>;
91		clocks = <&cru MCLK_I2S6_8CH_TX>, <&cru MCLK_I2S6_8CH_TX>, <&cru HCLK_I2S6_8CH>;
92		clock-names = "mclk_tx", "mclk_rx", "hclk";
93		assigned-clocks = <&cru CLK_I2S6_8CH_TX_SRC>;
94		assigned-clock-parents = <&cru PLL_AUPLL>;
95		dmas = <&dmac2 4>;
96		dma-names = "tx";
97		power-domains = <&power RK3588_PD_VO1>;
98		resets = <&cru SRST_M_I2S6_8CH_TX>;
99		reset-names = "tx-m";
100		#sound-dai-cells = <0>;
101		status = "disabled";
102	};
103
104	i2s7_8ch: i2s@fddf8000 {
105		compatible = "rockchip,rk3588-i2s-tdm";
106		reg = <0x0 0xfddf8000 0x0 0x1000>;
107		interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH 0>;
108		clocks = <&cru MCLK_I2S7_8CH_RX>, <&cru MCLK_I2S7_8CH_RX>, <&cru HCLK_I2S7_8CH>;
109		clock-names = "mclk_tx", "mclk_rx", "hclk";
110		assigned-clocks = <&cru CLK_I2S7_8CH_RX_SRC>;
111		assigned-clock-parents = <&cru PLL_AUPLL>;
112		dmas = <&dmac2 21>;
113		dma-names = "rx";
114		power-domains = <&power RK3588_PD_VO1>;
115		resets = <&cru SRST_M_I2S7_8CH_RX>;
116		reset-names = "rx-m";
117		#sound-dai-cells = <0>;
118		status = "disabled";
119	};
120
121	i2s10_8ch: i2s@fde00000 {
122		compatible = "rockchip,rk3588-i2s-tdm";
123		reg = <0x0 0xfde00000 0x0 0x1000>;
124		interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH 0>;
125		clocks = <&cru MCLK_I2S10_8CH_RX>, <&cru MCLK_I2S10_8CH_RX>, <&cru HCLK_I2S10_8CH>;
126		clock-names = "mclk_tx", "mclk_rx", "hclk";
127		assigned-clocks = <&cru CLK_I2S10_8CH_RX_SRC>;
128		assigned-clock-parents = <&cru PLL_AUPLL>;
129		dmas = <&dmac2 24>;
130		dma-names = "rx";
131		power-domains = <&power RK3588_PD_VO1>;
132		resets = <&cru SRST_M_I2S10_8CH_RX>;
133		reset-names = "rx-m";
134		#sound-dai-cells = <0>;
135		status = "disabled";
136	};
137
138	pcie3x4: pcie@fe150000 {
139		compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie";
140		#address-cells = <3>;
141		#size-cells = <2>;
142		bus-range = <0x00 0x0f>;
143		clocks = <&cru ACLK_PCIE_4L_MSTR>, <&cru ACLK_PCIE_4L_SLV>,
144			 <&cru ACLK_PCIE_4L_DBI>, <&cru PCLK_PCIE_4L>,
145			 <&cru CLK_PCIE_AUX0>, <&cru CLK_PCIE4L_PIPE>;
146		clock-names = "aclk_mst", "aclk_slv",
147			      "aclk_dbi", "pclk",
148			      "aux", "pipe";
149		device_type = "pci";
150		interrupts = <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH 0>,
151			     <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH 0>,
152			     <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH 0>,
153			     <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH 0>,
154			     <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH 0>;
155		interrupt-names = "sys", "pmc", "msg", "legacy", "err";
156		#interrupt-cells = <1>;
157		interrupt-map-mask = <0 0 0 7>;
158		interrupt-map = <0 0 0 1 &pcie3x4_intc 0>,
159				<0 0 0 2 &pcie3x4_intc 1>,
160				<0 0 0 3 &pcie3x4_intc 2>,
161				<0 0 0 4 &pcie3x4_intc 3>;
162		linux,pci-domain = <0>;
163		max-link-speed = <3>;
164		msi-map = <0x0000 &its1 0x0000 0x1000>;
165		num-lanes = <4>;
166		phys = <&pcie30phy>;
167		phy-names = "pcie-phy";
168		power-domains = <&power RK3588_PD_PCIE>;
169		ranges = <0x01000000 0x0 0xf0100000 0x0 0xf0100000 0x0 0x00100000>,
170			 <0x02000000 0x0 0xf0200000 0x0 0xf0200000 0x0 0x00e00000>,
171			 <0x03000000 0x0 0x40000000 0x9 0x00000000 0x0 0x40000000>;
172		reg = <0xa 0x40000000 0x0 0x00400000>,
173		      <0x0 0xfe150000 0x0 0x00010000>,
174		      <0x0 0xf0000000 0x0 0x00100000>;
175		reg-names = "dbi", "apb", "config";
176		resets = <&cru SRST_PCIE0_POWER_UP>, <&cru SRST_P_PCIE0>;
177		reset-names = "pwr", "pipe";
178		status = "disabled";
179
180		pcie3x4_intc: legacy-interrupt-controller {
181			interrupt-controller;
182			#address-cells = <0>;
183			#interrupt-cells = <1>;
184			interrupt-parent = <&gic>;
185			interrupts = <GIC_SPI 260 IRQ_TYPE_EDGE_RISING 0>;
186		};
187	};
188
189	pcie3x2: pcie@fe160000 {
190		compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie";
191		#address-cells = <3>;
192		#size-cells = <2>;
193		bus-range = <0x10 0x1f>;
194		clocks = <&cru ACLK_PCIE_2L_MSTR>, <&cru ACLK_PCIE_2L_SLV>,
195			 <&cru ACLK_PCIE_2L_DBI>, <&cru PCLK_PCIE_2L>,
196			 <&cru CLK_PCIE_AUX1>, <&cru CLK_PCIE2L_PIPE>;
197		clock-names = "aclk_mst", "aclk_slv",
198			      "aclk_dbi", "pclk",
199			      "aux", "pipe";
200		device_type = "pci";
201		interrupts = <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH 0>,
202			     <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH 0>,
203			     <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH 0>,
204			     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH 0>,
205			     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH 0>;
206		interrupt-names = "sys", "pmc", "msg", "legacy", "err";
207		#interrupt-cells = <1>;
208		interrupt-map-mask = <0 0 0 7>;
209		interrupt-map = <0 0 0 1 &pcie3x2_intc 0>,
210				<0 0 0 2 &pcie3x2_intc 1>,
211				<0 0 0 3 &pcie3x2_intc 2>,
212				<0 0 0 4 &pcie3x2_intc 3>;
213		linux,pci-domain = <1>;
214		max-link-speed = <3>;
215		msi-map = <0x1000 &its1 0x1000 0x1000>;
216		num-lanes = <2>;
217		phys = <&pcie30phy>;
218		phy-names = "pcie-phy";
219		power-domains = <&power RK3588_PD_PCIE>;
220		ranges = <0x01000000 0x0 0xf1100000 0x0 0xf1100000 0x0 0x00100000>,
221			 <0x02000000 0x0 0xf1200000 0x0 0xf1200000 0x0 0x00e00000>,
222			 <0x03000000 0x0 0x40000000 0x9 0x40000000 0x0 0x40000000>;
223		reg = <0xa 0x40400000 0x0 0x00400000>,
224		      <0x0 0xfe160000 0x0 0x00010000>,
225		      <0x0 0xf1000000 0x0 0x00100000>;
226		reg-names = "dbi", "apb", "config";
227		resets = <&cru SRST_PCIE1_POWER_UP>, <&cru SRST_P_PCIE1>;
228		reset-names = "pwr", "pipe";
229		status = "disabled";
230
231		pcie3x2_intc: legacy-interrupt-controller {
232			interrupt-controller;
233			#address-cells = <0>;
234			#interrupt-cells = <1>;
235			interrupt-parent = <&gic>;
236			interrupts = <GIC_SPI 255 IRQ_TYPE_EDGE_RISING 0>;
237		};
238	};
239
240	pcie2x1l0: pcie@fe170000 {
241		compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie";
242		bus-range = <0x20 0x2f>;
243		clocks = <&cru ACLK_PCIE_1L0_MSTR>, <&cru ACLK_PCIE_1L0_SLV>,
244			 <&cru ACLK_PCIE_1L0_DBI>, <&cru PCLK_PCIE_1L0>,
245			 <&cru CLK_PCIE_AUX2>, <&cru CLK_PCIE1L0_PIPE>;
246		clock-names = "aclk_mst", "aclk_slv",
247			      "aclk_dbi", "pclk",
248			      "aux", "pipe";
249		device_type = "pci";
250		interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH 0>,
251			     <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH 0>,
252			     <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH 0>,
253			     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH 0>,
254			     <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH 0>;
255		interrupt-names = "sys", "pmc", "msg", "legacy", "err";
256		#interrupt-cells = <1>;
257		interrupt-map-mask = <0 0 0 7>;
258		interrupt-map = <0 0 0 1 &pcie2x1l0_intc 0>,
259				<0 0 0 2 &pcie2x1l0_intc 1>,
260				<0 0 0 3 &pcie2x1l0_intc 2>,
261				<0 0 0 4 &pcie2x1l0_intc 3>;
262		linux,pci-domain = <2>;
263		max-link-speed = <2>;
264		msi-map = <0x2000 &its0 0x2000 0x1000>;
265		num-lanes = <1>;
266		phys = <&combphy1_ps PHY_TYPE_PCIE>;
267		phy-names = "pcie-phy";
268		power-domains = <&power RK3588_PD_PCIE>;
269		ranges = <0x01000000 0x0 0xf2100000 0x0 0xf2100000 0x0 0x00100000>,
270			 <0x02000000 0x0 0xf2200000 0x0 0xf2200000 0x0 0x00e00000>,
271			 <0x03000000 0x0 0x40000000 0x9 0x80000000 0x0 0x40000000>;
272		reg = <0xa 0x40800000 0x0 0x00400000>,
273		      <0x0 0xfe170000 0x0 0x00010000>,
274		      <0x0 0xf2000000 0x0 0x00100000>;
275		reg-names = "dbi", "apb", "config";
276		resets = <&cru SRST_PCIE2_POWER_UP>, <&cru SRST_P_PCIE2>;
277		reset-names = "pwr", "pipe";
278		#address-cells = <3>;
279		#size-cells = <2>;
280		status = "disabled";
281
282		pcie2x1l0_intc: legacy-interrupt-controller {
283			interrupt-controller;
284			#address-cells = <0>;
285			#interrupt-cells = <1>;
286			interrupt-parent = <&gic>;
287			interrupts = <GIC_SPI 240 IRQ_TYPE_EDGE_RISING 0>;
288		};
289	};
290
291	gmac0: ethernet@fe1b0000 {
292		compatible = "rockchip,rk3588-gmac", "snps,dwmac-4.20a";
293		reg = <0x0 0xfe1b0000 0x0 0x10000>;
294		interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH 0>,
295			     <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH 0>;
296		interrupt-names = "macirq", "eth_wake_irq";
297		clocks = <&cru CLK_GMAC_125M>, <&cru CLK_GMAC_50M>,
298			 <&cru PCLK_GMAC0>, <&cru ACLK_GMAC0>,
299			 <&cru CLK_GMAC0_PTP_REF>;
300		clock-names = "stmmaceth", "clk_mac_ref",
301			      "pclk_mac", "aclk_mac",
302			      "ptp_ref";
303		power-domains = <&power RK3588_PD_GMAC>;
304		resets = <&cru SRST_A_GMAC0>;
305		reset-names = "stmmaceth";
306		rockchip,grf = <&sys_grf>;
307		rockchip,php-grf = <&php_grf>;
308		snps,axi-config = <&gmac0_stmmac_axi_setup>;
309		snps,mixed-burst;
310		snps,mtl-rx-config = <&gmac0_mtl_rx_setup>;
311		snps,mtl-tx-config = <&gmac0_mtl_tx_setup>;
312		snps,tso;
313		status = "disabled";
314
315		mdio0: mdio {
316			compatible = "snps,dwmac-mdio";
317			#address-cells = <0x1>;
318			#size-cells = <0x0>;
319		};
320
321		gmac0_stmmac_axi_setup: stmmac-axi-config {
322			snps,blen = <0 0 0 0 16 8 4>;
323			snps,wr_osr_lmt = <4>;
324			snps,rd_osr_lmt = <8>;
325		};
326
327		gmac0_mtl_rx_setup: rx-queues-config {
328			snps,rx-queues-to-use = <2>;
329			queue0 {};
330			queue1 {};
331		};
332
333		gmac0_mtl_tx_setup: tx-queues-config {
334			snps,tx-queues-to-use = <2>;
335			queue0 {};
336			queue1 {};
337		};
338	};
339
340	sata1: sata@fe220000 {
341		compatible = "rockchip,rk3588-dwc-ahci", "snps,dwc-ahci";
342		reg = <0 0xfe220000 0 0x1000>;
343		interrupts = <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH 0>;
344		clocks = <&cru ACLK_SATA1>, <&cru CLK_PMALIVE1>,
345			 <&cru CLK_RXOOB1>, <&cru CLK_PIPEPHY1_REF>,
346			 <&cru CLK_PIPEPHY1_PIPE_ASIC_G>;
347		clock-names = "sata", "pmalive", "rxoob", "ref", "asic";
348		ports-implemented = <0x1>;
349		#address-cells = <1>;
350		#size-cells = <0>;
351		status = "disabled";
352
353		sata-port@0 {
354			reg = <0>;
355			hba-port-cap = <HBA_PORT_FBSCP>;
356			phys = <&combphy1_ps PHY_TYPE_SATA>;
357			phy-names = "sata-phy";
358			snps,rx-ts-max = <32>;
359			snps,tx-ts-max = <32>;
360		};
361	};
362
363	usbdp_phy1: phy@fed90000 {
364		compatible = "rockchip,rk3588-usbdp-phy";
365		reg = <0x0 0xfed90000 0x0 0x10000>;
366		#phy-cells = <1>;
367		clocks = <&cru CLK_USBDPPHY_MIPIDCPPHY_REF>,
368			 <&cru CLK_USBDP_PHY1_IMMORTAL>,
369			 <&cru PCLK_USBDPPHY1>,
370			 <&u2phy1>;
371		clock-names = "refclk", "immortal", "pclk", "utmi";
372		resets = <&cru SRST_USBDP_COMBO_PHY1_INIT>,
373			 <&cru SRST_USBDP_COMBO_PHY1_CMN>,
374			 <&cru SRST_USBDP_COMBO_PHY1_LANE>,
375			 <&cru SRST_USBDP_COMBO_PHY1_PCS>,
376			 <&cru SRST_P_USBDPPHY1>;
377		reset-names = "init", "cmn", "lane", "pcs_apb", "pma_apb";
378		rockchip,u2phy-grf = <&usb2phy1_grf>;
379		rockchip,usb-grf = <&usb_grf>;
380		rockchip,usbdpphy-grf = <&usbdpphy1_grf>;
381		rockchip,vo-grf = <&vo0_grf>;
382		status = "disabled";
383	};
384
385	combphy1_ps: phy@fee10000 {
386		compatible = "rockchip,rk3588-naneng-combphy";
387		reg = <0x0 0xfee10000 0x0 0x100>;
388		clocks = <&cru CLK_REF_PIPE_PHY1>, <&cru PCLK_PCIE_COMBO_PIPE_PHY1>,
389			 <&cru PCLK_PHP_ROOT>;
390		clock-names = "ref", "apb", "pipe";
391		assigned-clocks = <&cru CLK_REF_PIPE_PHY1>;
392		assigned-clock-rates = <100000000>;
393		#phy-cells = <1>;
394		resets = <&cru SRST_REF_PIPE_PHY1>, <&cru SRST_P_PCIE2_PHY1>;
395		reset-names = "phy", "apb";
396		rockchip,pipe-grf = <&php_grf>;
397		rockchip,pipe-phy-grf = <&pipe_phy1_grf>;
398		status = "disabled";
399	};
400
401	pcie30phy: phy@fee80000 {
402		compatible = "rockchip,rk3588-pcie3-phy";
403		reg = <0x0 0xfee80000 0x0 0x20000>;
404		#phy-cells = <0>;
405		clocks = <&cru PCLK_PCIE_COMBO_PIPE_PHY>;
406		clock-names = "pclk";
407		resets = <&cru SRST_PCIE30_PHY>;
408		reset-names = "phy";
409		rockchip,pipe-grf = <&php_grf>;
410		rockchip,phy-grf = <&pcie30_phy_grf>;
411		status = "disabled";
412	};
413};
414