1// SPDX-License-Identifier: (GPL-2.0+ OR MIT) 2/* 3 * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd 4 */ 5 6/dts-v1/; 7#include <dt-bindings/input/linux-event-codes.h> 8#include <dt-bindings/pwm/pwm.h> 9#include "rk3399.dtsi" 10#include "rk3399-opp.dtsi" 11 12/ { 13 model = "Firefly ROC-RK3399-PC Board"; 14 compatible = "firefly,roc-rk3399-pc", "rockchip,rk3399"; 15 16 aliases { 17 ethernet0 = &gmac; 18 mmc0 = &sdmmc; 19 mmc1 = &sdhci; 20 }; 21 22 chosen { 23 stdout-path = "serial2:1500000n8"; 24 }; 25 26 backlight: backlight { 27 compatible = "pwm-backlight"; 28 pwms = <&pwm0 0 25000 0>; 29 }; 30 31 clkin_gmac: external-gmac-clock { 32 compatible = "fixed-clock"; 33 clock-frequency = <125000000>; 34 clock-output-names = "clkin_gmac"; 35 #clock-cells = <0>; 36 }; 37 38 adc-keys { 39 compatible = "adc-keys"; 40 io-channels = <&saradc 1>; 41 io-channel-names = "buttons"; 42 keyup-threshold-microvolt = <1500000>; 43 poll-interval = <100>; 44 45 button-recovery { 46 label = "Recovery"; 47 linux,code = <KEY_VENDOR>; 48 press-threshold-microvolt = <18000>; 49 }; 50 }; 51 52 gpio-keys { 53 compatible = "gpio-keys"; 54 autorepeat; 55 pinctrl-names = "default"; 56 pinctrl-0 = <&pwr_key_l>; 57 58 key-power { 59 debounce-interval = <100>; 60 gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>; 61 label = "GPIO Key Power"; 62 linux,code = <KEY_POWER>; 63 wakeup-source; 64 }; 65 }; 66 67 ir-receiver { 68 compatible = "gpio-ir-receiver"; 69 gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>; 70 pinctrl-names = "default"; 71 pinctrl-0 = <&ir_int>; 72 }; 73 74 leds { 75 compatible = "gpio-leds"; 76 pinctrl-names = "default"; 77 pinctrl-0 = <&work_led_pin>, <&diy_led_pin>, <&yellow_led_pin>; 78 79 work_led: led-0 { 80 label = "green:work"; 81 gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>; 82 default-state = "on"; 83 linux,default-trigger = "heartbeat"; 84 }; 85 86 diy_led: led-1 { 87 label = "red:diy"; 88 gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>; 89 default-state = "off"; 90 linux,default-trigger = "mmc2"; 91 }; 92 93 yellow_led: led-2 { 94 label = "yellow:yellow-led"; 95 gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>; 96 default-state = "off"; 97 linux,default-trigger = "mmc1"; 98 }; 99 }; 100 101 sdio_pwrseq: sdio-pwrseq { 102 compatible = "mmc-pwrseq-simple"; 103 clocks = <&rk808 1>; 104 clock-names = "ext_clock"; 105 pinctrl-names = "default"; 106 pinctrl-0 = <&wifi_enable_h>; 107 108 /* 109 * On the module itself this is one of these (depending 110 * on the actual card populated): 111 * - SDIO_RESET_L_WL_REG_ON 112 * - PDN (power down when low) 113 */ 114 reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>; 115 }; 116 117 vcc_vbus_typec0: vcc-vbus-typec0 { 118 compatible = "regulator-fixed"; 119 regulator-name = "vcc_vbus_typec0"; 120 regulator-always-on; 121 regulator-boot-on; 122 regulator-min-microvolt = <5000000>; 123 regulator-max-microvolt = <5000000>; 124 }; 125 126 sys_12v: sys-12v { 127 compatible = "regulator-fixed"; 128 regulator-name = "sys_12v"; 129 regulator-always-on; 130 regulator-boot-on; 131 vin-supply = <&dc_12v>; 132 }; 133 134 /* switched by pmic_sleep */ 135 vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 { 136 compatible = "regulator-fixed"; 137 regulator-name = "vcc1v8_s3"; 138 regulator-always-on; 139 regulator-boot-on; 140 regulator-min-microvolt = <1800000>; 141 regulator-max-microvolt = <1800000>; 142 vin-supply = <&vcc_1v8>; 143 }; 144 145 vcc3v0_sd: vcc3v0-sd { 146 compatible = "regulator-fixed"; 147 enable-active-high; 148 gpio = <&gpio4 RK_PD6 GPIO_ACTIVE_HIGH>; 149 pinctrl-names = "default"; 150 pinctrl-0 = <&vcc3v0_sd_en>; 151 regulator-name = "vcc3v0_sd"; 152 regulator-boot-on; 153 regulator-min-microvolt = <3000000>; 154 regulator-max-microvolt = <3000000>; 155 vin-supply = <&vcc3v3_sys>; 156 }; 157 158 vcc3v3_sys: vcc3v3-sys { 159 compatible = "regulator-fixed"; 160 regulator-name = "vcc3v3_sys"; 161 regulator-always-on; 162 regulator-boot-on; 163 regulator-min-microvolt = <3300000>; 164 regulator-max-microvolt = <3300000>; 165 vin-supply = <&sys_12v>; 166 }; 167 168 vcca_0v9: vcca-0v9 { 169 compatible = "regulator-fixed"; 170 regulator-name = "vcca_0v9"; 171 regulator-always-on; 172 regulator-boot-on; 173 regulator-min-microvolt = <900000>; 174 regulator-max-microvolt = <900000>; 175 vin-supply = <&vcc3v3_sys>; 176 }; 177 178 /* Actually 3 regulators (host0, 1, 2) controlled by the same gpio */ 179 vcc5v0_host: vcc5v0-host-regulator { 180 compatible = "regulator-fixed"; 181 enable-active-high; 182 gpio = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>; 183 pinctrl-names = "default"; 184 pinctrl-0 = <&vcc5v0_host_en &hub_rst>; 185 regulator-name = "vcc5v0_host"; 186 vin-supply = <&vcc_sys>; 187 }; 188 189 vcc_vbus_typec1: vcc-vbus-typec1 { 190 compatible = "regulator-fixed"; 191 enable-active-high; 192 gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>; 193 pinctrl-names = "default"; 194 pinctrl-0 = <&vcc_vbus_typec1_en>; 195 regulator-name = "vcc_vbus_typec1"; 196 regulator-always-on; 197 vin-supply = <&vcc_sys>; 198 }; 199 200 vcc_sys: vcc-sys { 201 compatible = "regulator-fixed"; 202 enable-active-high; 203 gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>; 204 pinctrl-names = "default"; 205 pinctrl-0 = <&vcc_sys_en>; 206 regulator-name = "vcc_sys"; 207 regulator-boot-on; 208 regulator-min-microvolt = <5000000>; 209 regulator-max-microvolt = <5000000>; 210 vin-supply = <&sys_12v>; 211 }; 212 213 vdd_log: vdd-log { 214 compatible = "pwm-regulator"; 215 pwms = <&pwm2 0 25000 1>; 216 regulator-name = "vdd_log"; 217 regulator-always-on; 218 regulator-boot-on; 219 regulator-min-microvolt = <450000>; 220 regulator-max-microvolt = <1400000>; 221 pwm-supply = <&vcc3v3_sys>; 222 }; 223}; 224 225&cpu_l0 { 226 cpu-supply = <&vdd_cpu_l>; 227}; 228 229&cpu_l1 { 230 cpu-supply = <&vdd_cpu_l>; 231}; 232 233&cpu_l2 { 234 cpu-supply = <&vdd_cpu_l>; 235}; 236 237&cpu_l3 { 238 cpu-supply = <&vdd_cpu_l>; 239}; 240 241&cpu_b0 { 242 cpu-supply = <&vdd_cpu_b>; 243}; 244 245&cpu_b1 { 246 cpu-supply = <&vdd_cpu_b>; 247}; 248 249&emmc_phy { 250 status = "okay"; 251}; 252 253&gmac { 254 assigned-clocks = <&cru SCLK_RMII_SRC>; 255 assigned-clock-parents = <&clkin_gmac>; 256 clock_in_out = "input"; 257 phy-supply = <&vcc_lan>; 258 phy-mode = "rgmii"; 259 pinctrl-names = "default"; 260 pinctrl-0 = <&rgmii_pins>; 261 snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>; 262 snps,reset-active-low; 263 snps,reset-delays-us = <0 10000 50000>; 264 tx_delay = <0x28>; 265 rx_delay = <0x11>; 266 status = "okay"; 267}; 268 269&gpu { 270 mali-supply = <&vdd_gpu>; 271 status = "okay"; 272}; 273 274&hdmi { 275 avdd-0v9-supply = <&vcca0v9_hdmi>; 276 avdd-1v8-supply = <&vcca1v8_hdmi>; 277 ddc-i2c-bus = <&i2c3>; 278 pinctrl-names = "default"; 279 pinctrl-0 = <&hdmi_cec>; 280 status = "okay"; 281}; 282 283&hdmi_sound { 284 status = "okay"; 285}; 286 287&i2c0 { 288 clock-frequency = <400000>; 289 i2c-scl-rising-time-ns = <168>; 290 i2c-scl-falling-time-ns = <4>; 291 status = "okay"; 292 293 rk808: pmic@1b { 294 compatible = "rockchip,rk808"; 295 reg = <0x1b>; 296 interrupt-parent = <&gpio1>; 297 interrupts = <21 IRQ_TYPE_LEVEL_LOW>; 298 #clock-cells = <1>; 299 clock-output-names = "xin32k", "rk808-clkout2"; 300 pinctrl-names = "default"; 301 pinctrl-0 = <&pmic_int_l>; 302 rockchip,system-power-controller; 303 wakeup-source; 304 305 vcc1-supply = <&vcc3v3_sys>; 306 vcc2-supply = <&vcc3v3_sys>; 307 vcc3-supply = <&vcc3v3_sys>; 308 vcc4-supply = <&vcc3v3_sys>; 309 vcc6-supply = <&vcc3v3_sys>; 310 vcc7-supply = <&vcc3v3_sys>; 311 vcc8-supply = <&vcc3v3_sys>; 312 vcc9-supply = <&vcc3v3_sys>; 313 vcc10-supply = <&vcc3v3_sys>; 314 vcc11-supply = <&vcc3v3_sys>; 315 vcc12-supply = <&vcc3v3_sys>; 316 vddio-supply = <&vcc_3v0>; 317 318 regulators { 319 vdd_center: DCDC_REG1 { 320 regulator-name = "vdd_center"; 321 regulator-always-on; 322 regulator-boot-on; 323 regulator-min-microvolt = <750000>; 324 regulator-max-microvolt = <1350000>; 325 regulator-ramp-delay = <6001>; 326 regulator-state-mem { 327 regulator-off-in-suspend; 328 }; 329 }; 330 331 vdd_cpu_l: DCDC_REG2 { 332 regulator-name = "vdd_cpu_l"; 333 regulator-always-on; 334 regulator-boot-on; 335 regulator-min-microvolt = <750000>; 336 regulator-max-microvolt = <1350000>; 337 regulator-ramp-delay = <6001>; 338 regulator-state-mem { 339 regulator-off-in-suspend; 340 }; 341 }; 342 343 vcc_ddr: DCDC_REG3 { 344 regulator-name = "vcc_ddr"; 345 regulator-always-on; 346 regulator-boot-on; 347 regulator-state-mem { 348 regulator-on-in-suspend; 349 }; 350 }; 351 352 vcc_1v8: DCDC_REG4 { 353 regulator-name = "vcc_1v8"; 354 regulator-always-on; 355 regulator-boot-on; 356 regulator-min-microvolt = <1800000>; 357 regulator-max-microvolt = <1800000>; 358 regulator-state-mem { 359 regulator-on-in-suspend; 360 regulator-suspend-microvolt = <1800000>; 361 }; 362 }; 363 364 vcca1v8_codec: LDO_REG1 { 365 regulator-name = "vcca1v8_codec"; 366 regulator-always-on; 367 regulator-boot-on; 368 regulator-min-microvolt = <1800000>; 369 regulator-max-microvolt = <1800000>; 370 regulator-state-mem { 371 regulator-off-in-suspend; 372 }; 373 }; 374 375 vcca1v8_hdmi: LDO_REG2 { 376 regulator-name = "vcca1v8_hdmi"; 377 regulator-always-on; 378 regulator-boot-on; 379 regulator-min-microvolt = <1800000>; 380 regulator-max-microvolt = <1800000>; 381 regulator-state-mem { 382 regulator-off-in-suspend; 383 }; 384 }; 385 386 vcc1v8_pmu: LDO_REG3 { 387 regulator-name = "vcc1v8_pmu"; 388 regulator-always-on; 389 regulator-boot-on; 390 regulator-min-microvolt = <1800000>; 391 regulator-max-microvolt = <1800000>; 392 regulator-state-mem { 393 regulator-on-in-suspend; 394 regulator-suspend-microvolt = <1800000>; 395 }; 396 }; 397 398 vcc_sdio: LDO_REG4 { 399 regulator-name = "vcc_sdio"; 400 regulator-always-on; 401 regulator-boot-on; 402 regulator-min-microvolt = <1800000>; 403 regulator-max-microvolt = <3000000>; 404 regulator-state-mem { 405 regulator-on-in-suspend; 406 regulator-suspend-microvolt = <3000000>; 407 }; 408 }; 409 410 vcca3v0_codec: LDO_REG5 { 411 regulator-name = "vcca3v0_codec"; 412 regulator-always-on; 413 regulator-boot-on; 414 regulator-min-microvolt = <3000000>; 415 regulator-max-microvolt = <3000000>; 416 regulator-state-mem { 417 regulator-off-in-suspend; 418 }; 419 }; 420 421 vcc_1v5: LDO_REG6 { 422 regulator-name = "vcc_1v5"; 423 regulator-always-on; 424 regulator-boot-on; 425 regulator-min-microvolt = <1500000>; 426 regulator-max-microvolt = <1500000>; 427 regulator-state-mem { 428 regulator-on-in-suspend; 429 regulator-suspend-microvolt = <1500000>; 430 }; 431 }; 432 433 vcca0v9_hdmi: LDO_REG7 { 434 regulator-name = "vcca0v9_hdmi"; 435 regulator-always-on; 436 regulator-boot-on; 437 regulator-min-microvolt = <900000>; 438 regulator-max-microvolt = <900000>; 439 regulator-state-mem { 440 regulator-off-in-suspend; 441 }; 442 }; 443 444 vcc_3v0: LDO_REG8 { 445 regulator-name = "vcc_3v0"; 446 regulator-always-on; 447 regulator-boot-on; 448 regulator-min-microvolt = <3000000>; 449 regulator-max-microvolt = <3000000>; 450 regulator-state-mem { 451 regulator-on-in-suspend; 452 regulator-suspend-microvolt = <3000000>; 453 }; 454 }; 455 456 vcc3v3_s3: vcc_lan: SWITCH_REG1 { 457 regulator-name = "vcc3v3_s3"; 458 regulator-always-on; 459 regulator-boot-on; 460 regulator-state-mem { 461 regulator-off-in-suspend; 462 }; 463 }; 464 465 vcc3v3_s0: SWITCH_REG2 { 466 regulator-name = "vcc3v3_s0"; 467 regulator-always-on; 468 regulator-boot-on; 469 regulator-state-mem { 470 regulator-off-in-suspend; 471 }; 472 }; 473 }; 474 }; 475 476 vdd_cpu_b: regulator@40 { 477 compatible = "silergy,syr827"; 478 reg = <0x40>; 479 fcs,suspend-voltage-selector = <1>; 480 pinctrl-names = "default"; 481 pinctrl-0 = <&vsel1_pin>; 482 regulator-name = "vdd_cpu_b"; 483 regulator-min-microvolt = <712500>; 484 regulator-max-microvolt = <1500000>; 485 regulator-ramp-delay = <1000>; 486 regulator-always-on; 487 regulator-boot-on; 488 vin-supply = <&vcc3v3_sys>; 489 490 regulator-state-mem { 491 regulator-off-in-suspend; 492 }; 493 }; 494 495 vdd_gpu: regulator@41 { 496 compatible = "silergy,syr828"; 497 reg = <0x41>; 498 fcs,suspend-voltage-selector = <1>; 499 pinctrl-names = "default"; 500 pinctrl-0 = <&vsel2_pin>; 501 regulator-name = "vdd_gpu"; 502 regulator-min-microvolt = <712500>; 503 regulator-max-microvolt = <1500000>; 504 regulator-ramp-delay = <1000>; 505 regulator-always-on; 506 regulator-boot-on; 507 vin-supply = <&vcc3v3_sys>; 508 509 regulator-state-mem { 510 regulator-off-in-suspend; 511 }; 512 }; 513}; 514 515&i2c1 { 516 i2c-scl-rising-time-ns = <300>; 517 i2c-scl-falling-time-ns = <15>; 518 status = "okay"; 519}; 520 521&i2c3 { 522 i2c-scl-rising-time-ns = <450>; 523 i2c-scl-falling-time-ns = <15>; 524 status = "okay"; 525}; 526 527&i2c4 { 528 i2c-scl-rising-time-ns = <600>; 529 i2c-scl-falling-time-ns = <20>; 530 status = "okay"; 531 532 fusb1: usb-typec@22 { 533 compatible = "fcs,fusb302"; 534 reg = <0x22>; 535 interrupt-parent = <&gpio1>; 536 interrupts = <1 IRQ_TYPE_LEVEL_LOW>; 537 pinctrl-names = "default"; 538 pinctrl-0 = <&fusb1_int>; 539 vbus-supply = <&vcc_vbus_typec1>; 540 status = "okay"; 541 }; 542}; 543 544&i2c7 { 545 i2c-scl-rising-time-ns = <600>; 546 i2c-scl-falling-time-ns = <20>; 547 status = "okay"; 548 549 fusb0: usb-typec@22 { 550 compatible = "fcs,fusb302"; 551 reg = <0x22>; 552 interrupt-parent = <&gpio1>; 553 interrupts = <2 IRQ_TYPE_LEVEL_LOW>; 554 pinctrl-names = "default"; 555 pinctrl-0 = <&fusb0_int>; 556 vbus-supply = <&vcc_vbus_typec0>; 557 status = "okay"; 558 }; 559 560 mp8859: regulator@66 { 561 compatible = "mps,mp8859"; 562 reg = <0x66>; 563 dc_12v: mp8859_dcdc { 564 regulator-name = "dc_12v"; 565 regulator-min-microvolt = <12000000>; 566 regulator-max-microvolt = <12000000>; 567 regulator-always-on; 568 regulator-boot-on; 569 vin-supply = <&vcc_vbus_typec0>; 570 571 regulator-state-mem { 572 regulator-on-in-suspend; 573 regulator-suspend-microvolt = <12000000>; 574 }; 575 }; 576 }; 577}; 578 579&i2s0 { 580 rockchip,playback-channels = <8>; 581 rockchip,capture-channels = <8>; 582 status = "okay"; 583}; 584 585&i2s1 { 586 rockchip,playback-channels = <2>; 587 rockchip,capture-channels = <2>; 588 status = "okay"; 589}; 590 591&i2s2 { 592 status = "okay"; 593}; 594 595&io_domains { 596 audio-supply = <&vcca1v8_codec>; 597 bt656-supply = <&vcc_3v0>; 598 gpio1830-supply = <&vcc_3v0>; 599 sdmmc-supply = <&vcc_sdio>; 600 status = "okay"; 601}; 602 603&pmu_io_domains { 604 pmu1830-supply = <&vcc_3v0>; 605 status = "okay"; 606}; 607 608&pinctrl { 609 buttons { 610 pwr_key_l: pwr-key-l { 611 rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>; 612 }; 613 }; 614 615 ir { 616 ir_int: ir-int { 617 rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>; 618 }; 619 }; 620 621 lcd-panel { 622 lcd_panel_reset: lcd-panel-reset { 623 rockchip,pins = <4 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>; 624 }; 625 }; 626 627 leds { 628 diy_led_pin: diy-led-pin { 629 rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>; 630 }; 631 632 work_led_pin: work-led-pin { 633 rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>; 634 }; 635 636 yellow_led_pin: yellow-led-pin { 637 rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>; 638 }; 639 }; 640 641 pmic { 642 vsel1_pin: vsel1-pin { 643 rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>; 644 }; 645 646 vsel2_pin: vsel2-pin { 647 rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>; 648 }; 649 }; 650 651 sdio-pwrseq { 652 wifi_enable_h: wifi-enable-h { 653 rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; 654 }; 655 }; 656 657 sdmmc { 658 vcc3v0_sd_en: vcc3v0-sd-en { 659 rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>; 660 }; 661 }; 662 663 pmic { 664 pmic_int_l: pmic-int-l { 665 rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>; 666 }; 667 }; 668 669 usb2 { 670 vcc5v0_host_en: vcc5v0-host-en { 671 rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>; 672 }; 673 674 vcc_sys_en: vcc-sys-en { 675 rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>; 676 }; 677 678 hub_rst: hub-rst { 679 rockchip,pins = <2 RK_PA4 RK_FUNC_GPIO &pcfg_output_high>; 680 }; 681 }; 682 683 usb-typec { 684 vcc_vbus_typec1_en: vcc-vbus-typec1-en { 685 rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>; 686 }; 687 }; 688 689 fusb30x { 690 fusb0_int: fusb0-int { 691 rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>; 692 }; 693 694 fusb1_int: fusb1-int { 695 rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>; 696 }; 697 }; 698}; 699 700&pwm0 { 701 status = "okay"; 702}; 703 704&pwm2 { 705 status = "okay"; 706}; 707 708&saradc { 709 vref-supply = <&vcca1v8_s3>; 710 status = "okay"; 711}; 712 713&sdmmc { 714 bus-width = <4>; 715 cap-sd-highspeed; 716 cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>; 717 disable-wp; 718 max-frequency = <150000000>; 719 pinctrl-names = "default"; 720 pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>; 721 sd-uhs-sdr104; 722 vmmc-supply = <&vcc3v0_sd>; 723 vqmmc-supply = <&vcc_sdio>; 724 status = "okay"; 725}; 726 727&sdhci { 728 bus-width = <8>; 729 non-removable; 730 status = "okay"; 731}; 732 733&spi1 { 734 status = "okay"; 735 736 flash@0 { 737 compatible = "jedec,spi-nor"; 738 reg = <0>; 739 spi-max-frequency = <30000000>; 740 }; 741}; 742 743&tcphy0 { 744 status = "okay"; 745}; 746 747&tcphy1 { 748 status = "okay"; 749}; 750 751&tsadc { 752 /* tshut mode 0:CRU 1:GPIO */ 753 rockchip,hw-tshut-mode = <1>; 754 /* tshut polarity 0:LOW 1:HIGH */ 755 rockchip,hw-tshut-polarity = <1>; 756 status = "okay"; 757}; 758 759&u2phy0 { 760 status = "okay"; 761 762 u2phy0_otg: otg-port { 763 phy-supply = <&vcc_vbus_typec0>; 764 status = "okay"; 765 }; 766 767 u2phy0_host: host-port { 768 phy-supply = <&vcc5v0_host>; 769 status = "okay"; 770 }; 771}; 772 773&u2phy1 { 774 status = "okay"; 775 776 u2phy1_otg: otg-port { 777 phy-supply = <&vcc_vbus_typec1>; 778 status = "okay"; 779 }; 780 781 u2phy1_host: host-port { 782 phy-supply = <&vcc5v0_host>; 783 status = "okay"; 784 }; 785}; 786 787&uart0 { 788 pinctrl-names = "default"; 789 pinctrl-0 = <&uart0_xfer &uart0_cts>; 790 status = "okay"; 791}; 792 793&uart2 { 794 status = "okay"; 795}; 796 797&usb_host0_ehci { 798 status = "okay"; 799}; 800 801&usb_host0_ohci { 802 status = "okay"; 803}; 804 805&usb_host1_ehci { 806 status = "okay"; 807}; 808 809&usb_host1_ohci { 810 status = "okay"; 811}; 812 813&usbdrd3_0 { 814 status = "okay"; 815}; 816 817&usbdrd_dwc3_0 { 818 status = "okay"; 819}; 820 821&usbdrd3_1 { 822 status = "okay"; 823}; 824 825&usbdrd_dwc3_1 { 826 status = "okay"; 827 dr_mode = "host"; 828}; 829 830&vopb { 831 status = "okay"; 832}; 833 834&vopb_mmu { 835 status = "okay"; 836}; 837 838&vopl { 839 status = "okay"; 840}; 841 842&vopl_mmu { 843 status = "okay"; 844}; 845