xref: /linux/arch/arm64/boot/dts/renesas/salvator-common.dtsi (revision 4b911a9690d72641879ea6d13cce1de31d346d79)
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Device Tree Source for common parts of Salvator-X board variants
4 *
5 * Copyright (C) 2015-2016 Renesas Electronics Corp.
6 */
7
8/*
9 * SSI-AK4613
10 *
11 * This command is required when Playback/Capture
12 *
13 *	amixer set "DVC Out" 100%
14 *	amixer set "DVC In" 100%
15 *
16 * You can use Mute
17 *
18 *	amixer set "DVC Out Mute" on
19 *	amixer set "DVC In Mute" on
20 *
21 * You can use Volume Ramp
22 *
23 *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
24 *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
25 *	amixer set "DVC Out Ramp" on
26 *	aplay xxx.wav &
27 *	amixer set "DVC Out"  80%  // Volume Down
28 *	amixer set "DVC Out" 100%  // Volume Up
29 */
30
31#include <dt-bindings/gpio/gpio.h>
32#include <dt-bindings/input/input.h>
33
34/ {
35	aliases {
36		i2c0 = &i2c0;
37		i2c1 = &i2c1;
38		i2c2 = &i2c2;
39		i2c3 = &i2c3;
40		i2c4 = &i2c4;
41		i2c5 = &i2c5;
42		i2c6 = &i2c6;
43		i2c7 = &i2c_dvfs;
44		serial0 = &scif2;
45		serial1 = &hscif1;
46		ethernet0 = &avb;
47		mmc0 = &sdhi2;
48		mmc1 = &sdhi0;
49		mmc2 = &sdhi3;
50	};
51
52	chosen {
53		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
54		stdout-path = "serial0:115200n8";
55	};
56
57	audio_clkout: audio-clkout {
58		/*
59		 * This is same as <&rcar_sound 0>
60		 * but needed to avoid cs2000/rcar_sound probe dead-lock
61		 */
62		compatible = "fixed-clock";
63		#clock-cells = <0>;
64		clock-frequency = <12288000>;
65	};
66
67	backlight: backlight {
68		compatible = "pwm-backlight";
69		pwms = <&pwm1 0 50000>;
70
71		brightness-levels = <256 128 64 16 8 4 0>;
72		default-brightness-level = <6>;
73
74		power-supply = <&reg_12v>;
75		enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
76	};
77
78	cvbs-in {
79		compatible = "composite-video-connector";
80		label = "CVBS IN";
81
82		port {
83			cvbs_con: endpoint {
84				remote-endpoint = <&adv7482_ain7>;
85			};
86		};
87	};
88
89	hdmi-in {
90		compatible = "hdmi-connector";
91		label = "HDMI IN";
92		type = "a";
93
94		port {
95			hdmi_in_con: endpoint {
96				remote-endpoint = <&adv7482_hdmi>;
97			};
98		};
99	};
100
101	hdmi0-out {
102		compatible = "hdmi-connector";
103		label = "HDMI0 OUT";
104		type = "a";
105
106		port {
107			hdmi0_con: endpoint {
108				remote-endpoint = <&rcar_dw_hdmi0_out>;
109			};
110		};
111	};
112
113	hdmi1-out {
114		compatible = "hdmi-connector";
115		label = "HDMI1 OUT";
116		type = "a";
117
118		port {
119			hdmi1_con: endpoint {
120			};
121		};
122	};
123
124	keys {
125		compatible = "gpio-keys";
126
127		pinctrl-0 = <&keys_pins>;
128		pinctrl-names = "default";
129
130		key-1 {
131			gpios = <&gpio5 17 GPIO_ACTIVE_LOW>;
132			linux,code = <KEY_1>;
133			label = "SW4-1";
134			wakeup-source;
135			debounce-interval = <20>;
136		};
137		key-2 {
138			gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
139			linux,code = <KEY_2>;
140			label = "SW4-2";
141			wakeup-source;
142			debounce-interval = <20>;
143		};
144		key-3 {
145			gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
146			linux,code = <KEY_3>;
147			label = "SW4-3";
148			wakeup-source;
149			debounce-interval = <20>;
150		};
151		key-4 {
152			gpios = <&gpio5 23 GPIO_ACTIVE_LOW>;
153			linux,code = <KEY_4>;
154			label = "SW4-4";
155			wakeup-source;
156			debounce-interval = <20>;
157		};
158		key-a {
159			gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
160			linux,code = <KEY_A>;
161			label = "TSW0";
162			wakeup-source;
163			debounce-interval = <20>;
164		};
165		key-b {
166			gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
167			linux,code = <KEY_B>;
168			label = "TSW1";
169			wakeup-source;
170			debounce-interval = <20>;
171		};
172		key-c {
173			gpios = <&gpio6 13 GPIO_ACTIVE_LOW>;
174			linux,code = <KEY_C>;
175			label = "TSW2";
176			wakeup-source;
177			debounce-interval = <20>;
178		};
179	};
180
181	reg_1p8v: regulator-1p8v {
182		compatible = "regulator-fixed";
183		regulator-name = "fixed-1.8V";
184		regulator-min-microvolt = <1800000>;
185		regulator-max-microvolt = <1800000>;
186		regulator-boot-on;
187		regulator-always-on;
188	};
189
190	reg_3p3v: regulator-3p3v {
191		compatible = "regulator-fixed";
192		regulator-name = "fixed-3.3V";
193		regulator-min-microvolt = <3300000>;
194		regulator-max-microvolt = <3300000>;
195		regulator-boot-on;
196		regulator-always-on;
197	};
198
199	reg_12v: regulator-12v {
200		compatible = "regulator-fixed";
201		regulator-name = "fixed-12V";
202		regulator-min-microvolt = <12000000>;
203		regulator-max-microvolt = <12000000>;
204		regulator-boot-on;
205		regulator-always-on;
206	};
207
208	sound_card: sound {
209		compatible = "audio-graph-card";
210
211		label = "rcar-sound";
212
213		dais = <&rsnd_port0	/* ak4613 */
214			&rsnd_port1	/* HDMI0  */
215#ifdef SOC_HAS_HDMI1
216			&rsnd_port2	/* HDMI1  */
217#endif
218			>;
219	};
220
221	vbus0_usb2: regulator-vbus0-usb2 {
222		compatible = "regulator-fixed";
223
224		regulator-name = "USB20_VBUS0";
225		regulator-min-microvolt = <5000000>;
226		regulator-max-microvolt = <5000000>;
227
228		gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
229		enable-active-high;
230	};
231
232	vcc_sdhi0: regulator-vcc-sdhi0 {
233		compatible = "regulator-fixed";
234
235		regulator-name = "SDHI0 Vcc";
236		regulator-min-microvolt = <3300000>;
237		regulator-max-microvolt = <3300000>;
238
239		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
240		enable-active-high;
241	};
242
243	vccq_sdhi0: regulator-vccq-sdhi0 {
244		compatible = "regulator-gpio";
245
246		regulator-name = "SDHI0 VccQ";
247		regulator-min-microvolt = <1800000>;
248		regulator-max-microvolt = <3300000>;
249
250		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
251		gpios-states = <1>;
252		states = <3300000 1>, <1800000 0>;
253	};
254
255	vcc_sdhi3: regulator-vcc-sdhi3 {
256		compatible = "regulator-fixed";
257
258		regulator-name = "SDHI3 Vcc";
259		regulator-min-microvolt = <3300000>;
260		regulator-max-microvolt = <3300000>;
261
262		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
263		enable-active-high;
264	};
265
266	vccq_sdhi3: regulator-vccq-sdhi3 {
267		compatible = "regulator-gpio";
268
269		regulator-name = "SDHI3 VccQ";
270		regulator-min-microvolt = <1800000>;
271		regulator-max-microvolt = <3300000>;
272
273		gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
274		gpios-states = <1>;
275		states = <3300000 1>, <1800000 0>;
276	};
277
278	vga {
279		compatible = "vga-connector";
280
281		port {
282			vga_in: endpoint {
283				remote-endpoint = <&adv7123_out>;
284			};
285		};
286	};
287
288	vga-encoder {
289		compatible = "adi,adv7123";
290
291		ports {
292			#address-cells = <1>;
293			#size-cells = <0>;
294
295			port@0 {
296				reg = <0>;
297				adv7123_in: endpoint {
298					remote-endpoint = <&du_out_rgb>;
299				};
300			};
301			port@1 {
302				reg = <1>;
303				adv7123_out: endpoint {
304					remote-endpoint = <&vga_in>;
305				};
306			};
307		};
308	};
309
310	x12_clk: x12 {
311		compatible = "fixed-clock";
312		#clock-cells = <0>;
313		clock-frequency = <24576000>;
314	};
315
316	/* External DU dot clocks */
317	x21_clk: x21-clock {
318		compatible = "fixed-clock";
319		#clock-cells = <0>;
320		clock-frequency = <33000000>;
321	};
322
323	x22_clk: x22-clock {
324		compatible = "fixed-clock";
325		#clock-cells = <0>;
326		clock-frequency = <33000000>;
327	};
328
329	x23_clk: x23-clock {
330		compatible = "fixed-clock";
331		#clock-cells = <0>;
332		clock-frequency = <25000000>;
333	};
334};
335
336&a57_0 {
337	cpu-supply = <&dvfs>;
338};
339
340&audio_clk_a {
341	clock-frequency = <22579200>;
342};
343
344&avb {
345	pinctrl-0 = <&avb_pins>;
346	pinctrl-names = "default";
347	phy-handle = <&phy0>;
348	tx-internal-delay-ps = <2000>;
349	status = "okay";
350
351	phy0: ethernet-phy@0 {
352		compatible = "ethernet-phy-id0022.1622",
353			     "ethernet-phy-ieee802.3-c22";
354		rxc-skew-ps = <1500>;
355		reg = <0>;
356		interrupt-parent = <&gpio2>;
357		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
358		reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
359	};
360};
361
362&csi20 {
363	status = "okay";
364
365	ports {
366		port@0 {
367			csi20_in: endpoint {
368				clock-lanes = <0>;
369				data-lanes = <1>;
370				remote-endpoint = <&adv7482_txb>;
371			};
372		};
373	};
374};
375
376&csi40 {
377	status = "okay";
378
379	ports {
380		port@0 {
381			csi40_in: endpoint {
382				clock-lanes = <0>;
383				data-lanes = <1 2 3 4>;
384				remote-endpoint = <&adv7482_txa>;
385			};
386		};
387	};
388};
389
390&du {
391	pinctrl-0 = <&du_pins>;
392	pinctrl-names = "default";
393	status = "okay";
394
395	ports {
396		port@0 {
397			du_out_rgb: endpoint {
398				remote-endpoint = <&adv7123_in>;
399			};
400		};
401	};
402};
403
404&ehci0 {
405	dr_mode = "otg";
406	status = "okay";
407};
408
409&ehci1 {
410	status = "okay";
411};
412
413&extalr_clk {
414	clock-frequency = <32768>;
415};
416
417&hdmi0 {
418	status = "okay";
419
420	ports {
421		port@1 {
422			reg = <1>;
423			rcar_dw_hdmi0_out: endpoint {
424				remote-endpoint = <&hdmi0_con>;
425			};
426		};
427		port@2 {
428			reg = <2>;
429			dw_hdmi0_snd_in: endpoint {
430				remote-endpoint = <&rsnd_endpoint1>;
431			};
432		};
433	};
434};
435
436#ifdef SOC_HAS_HDMI1
437&hdmi1 {
438	status = "okay";
439
440	ports {
441		port@1 {
442			reg = <1>;
443			rcar_dw_hdmi1_out: endpoint {
444				remote-endpoint = <&hdmi1_con>;
445			};
446		};
447		port@2 {
448			reg = <2>;
449			dw_hdmi1_snd_in: endpoint {
450				remote-endpoint = <&rsnd_endpoint2>;
451			};
452		};
453	};
454};
455
456&hdmi1_con {
457	remote-endpoint = <&rcar_dw_hdmi1_out>;
458};
459#endif /* SOC_HAS_HDMI1 */
460
461&hscif1 {
462	pinctrl-0 = <&hscif1_pins>;
463	pinctrl-names = "default";
464
465	uart-has-rtscts;
466	/* Please only enable hscif1 or scif1 */
467	status = "okay";
468};
469
470&hsusb {
471	dr_mode = "otg";
472	status = "okay";
473};
474
475&i2c2 {
476	pinctrl-0 = <&i2c2_pins>;
477	pinctrl-names = "default";
478
479	status = "okay";
480
481	clock-frequency = <100000>;
482
483	ak4613: codec@10 {
484		compatible = "asahi-kasei,ak4613";
485		#sound-dai-cells = <0>;
486		reg = <0x10>;
487		clocks = <&rcar_sound 3>;
488
489		asahi-kasei,in1-single-end;
490		asahi-kasei,in2-single-end;
491		asahi-kasei,out1-single-end;
492		asahi-kasei,out2-single-end;
493		asahi-kasei,out3-single-end;
494		asahi-kasei,out4-single-end;
495		asahi-kasei,out5-single-end;
496		asahi-kasei,out6-single-end;
497
498		port {
499			ak4613_endpoint: endpoint {
500				remote-endpoint = <&rsnd_endpoint0>;
501			};
502		};
503	};
504
505	cs2000: clk_multiplier@4f {
506		#clock-cells = <0>;
507		compatible = "cirrus,cs2000-cp";
508		reg = <0x4f>;
509		clocks = <&audio_clkout>, <&x12_clk>;
510		clock-names = "clk_in", "ref_clk";
511
512		assigned-clocks = <&cs2000>;
513		assigned-clock-rates = <24576000>; /* 1/1 divide */
514	};
515};
516
517&i2c4 {
518	status = "okay";
519
520	pca9654: gpio@20 {
521		compatible = "onnn,pca9654";
522		reg = <0x20>;
523		gpio-controller;
524		#gpio-cells = <2>;
525	};
526
527	video-receiver@70 {
528		compatible = "adi,adv7482";
529		reg = <0x70 0x71 0x72 0x73 0x74 0x75
530		       0x60 0x61 0x62 0x63 0x64 0x65>;
531		reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater",
532			    "infoframe", "cbus", "cec", "sdp", "txa", "txb" ;
533
534		interrupt-parent = <&gpio6>;
535		interrupt-names = "intrq1", "intrq2";
536		interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
537			     <31 IRQ_TYPE_LEVEL_LOW>;
538
539		ports {
540			#address-cells = <1>;
541			#size-cells = <0>;
542
543			port@7 {
544				reg = <7>;
545
546				adv7482_ain7: endpoint {
547					remote-endpoint = <&cvbs_con>;
548				};
549			};
550
551			port@8 {
552				reg = <8>;
553
554				adv7482_hdmi: endpoint {
555					remote-endpoint = <&hdmi_in_con>;
556				};
557			};
558
559			port@a {
560				reg = <10>;
561
562				adv7482_txa: endpoint {
563					clock-lanes = <0>;
564					data-lanes = <1 2 3 4>;
565					remote-endpoint = <&csi40_in>;
566				};
567			};
568
569			port@b {
570				reg = <11>;
571
572				adv7482_txb: endpoint {
573					clock-lanes = <0>;
574					data-lanes = <1>;
575					remote-endpoint = <&csi20_in>;
576				};
577			};
578		};
579	};
580
581	csa_vdd: adc@7c {
582		compatible = "maxim,max9611";
583		reg = <0x7c>;
584
585		shunt-resistor-micro-ohms = <5000>;
586	};
587
588	csa_dvfs: adc@7f {
589		compatible = "maxim,max9611";
590		reg = <0x7f>;
591
592		shunt-resistor-micro-ohms = <5000>;
593	};
594};
595
596&i2c_dvfs {
597	status = "okay";
598
599	clock-frequency = <400000>;
600
601	pmic: pmic@30 {
602		pinctrl-0 = <&irq0_pins>;
603		pinctrl-names = "default";
604
605		compatible = "rohm,bd9571mwv";
606		reg = <0x30>;
607		interrupt-parent = <&intc_ex>;
608		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
609		interrupt-controller;
610		#interrupt-cells = <2>;
611		gpio-controller;
612		#gpio-cells = <2>;
613		rohm,ddr-backup-power = <0xf>;
614		rohm,rstbmode-level;
615
616		regulators {
617			dvfs: dvfs {
618				regulator-name = "dvfs";
619				regulator-min-microvolt = <750000>;
620				regulator-max-microvolt = <1030000>;
621				regulator-boot-on;
622				regulator-always-on;
623			};
624		};
625	};
626
627	eeprom@50 {
628		compatible = "rohm,br24t01", "atmel,24c01";
629		reg = <0x50>;
630		pagesize = <8>;
631	};
632};
633
634&ohci0 {
635	dr_mode = "otg";
636	status = "okay";
637};
638
639&ohci1 {
640	status = "okay";
641};
642
643&pcie_bus_clk {
644	clock-frequency = <100000000>;
645};
646
647&pciec0 {
648	status = "okay";
649};
650
651&pciec1 {
652	status = "okay";
653};
654
655&pfc {
656	pinctrl-0 = <&scif_clk_pins>;
657	pinctrl-names = "default";
658
659	avb_pins: avb {
660		mux {
661			groups = "avb_link", "avb_mdio", "avb_mii";
662			function = "avb";
663		};
664
665		pins_mdio {
666			groups = "avb_mdio";
667			drive-strength = <24>;
668		};
669
670		pins_mii_tx {
671			pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
672			       "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
673			drive-strength = <12>;
674		};
675	};
676
677	du_pins: du {
678		groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
679		function = "du";
680	};
681
682	hscif1_pins: hscif1 {
683		groups = "hscif1_data_a", "hscif1_ctrl_a";
684		function = "hscif1";
685	};
686
687	i2c2_pins: i2c2 {
688		groups = "i2c2_a";
689		function = "i2c2";
690	};
691
692	irq0_pins: irq0 {
693		groups = "intc_ex_irq0";
694		function = "intc_ex";
695	};
696
697	keys_pins: keys {
698		pins = "GP_5_17", "GP_5_20", "GP_5_22";
699		bias-pull-up;
700	};
701
702	pwm1_pins: pwm1 {
703		groups = "pwm1_a";
704		function = "pwm1";
705	};
706
707	scif1_pins: scif1 {
708		groups = "scif1_data_a", "scif1_ctrl";
709		function = "scif1";
710	};
711
712	scif2_pins: scif2 {
713		groups = "scif2_data_a";
714		function = "scif2";
715	};
716
717	scif_clk_pins: scif_clk {
718		groups = "scif_clk_a";
719		function = "scif_clk";
720	};
721
722	sdhi0_pins: sd0 {
723		groups = "sdhi0_data4", "sdhi0_ctrl";
724		function = "sdhi0";
725		power-source = <3300>;
726	};
727
728	sdhi0_pins_uhs: sd0_uhs {
729		groups = "sdhi0_data4", "sdhi0_ctrl";
730		function = "sdhi0";
731		power-source = <1800>;
732	};
733
734	sdhi2_pins: sd2 {
735		groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds";
736		function = "sdhi2";
737		power-source = <1800>;
738	};
739
740	sdhi3_pins: sd3 {
741		groups = "sdhi3_data4", "sdhi3_ctrl";
742		function = "sdhi3";
743		power-source = <3300>;
744	};
745
746	sdhi3_pins_uhs: sd3_uhs {
747		groups = "sdhi3_data4", "sdhi3_ctrl";
748		function = "sdhi3";
749		power-source = <1800>;
750	};
751
752	sound_pins: sound {
753		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
754		function = "ssi";
755	};
756
757	sound_clk_pins: sound_clk {
758		groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
759			 "audio_clkout_a", "audio_clkout3_a";
760		function = "audio_clk";
761	};
762
763	usb0_pins: usb0 {
764		groups = "usb0";
765		function = "usb0";
766	};
767
768	usb1_pins: usb1 {
769		mux {
770			groups = "usb1";
771			function = "usb1";
772		};
773
774		ovc {
775			pins = "GP_6_27";
776			bias-pull-up;
777		};
778
779		pwen {
780			pins = "GP_6_26";
781			bias-pull-down;
782		};
783	};
784
785	usb30_pins: usb30 {
786		groups = "usb30";
787		function = "usb30";
788	};
789};
790
791&pwm1 {
792	pinctrl-0 = <&pwm1_pins>;
793	pinctrl-names = "default";
794
795	status = "okay";
796};
797
798&rcar_sound {
799	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
800	pinctrl-names = "default";
801
802	/* audio_clkout0/1/2/3 */
803	#clock-cells = <1>;
804	clock-frequency = <12288000 11289600>;
805
806	status = "okay";
807
808	/* update <audio_clk_b> to <cs2000> */
809	clocks = <&cpg CPG_MOD 1005>,
810		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
811		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
812		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
813		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
814		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
815		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
816		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
817		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
818		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
819		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
820		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
821		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
822		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
823		 <&audio_clk_a>, <&cs2000>,
824		 <&audio_clk_c>,
825		 <&cpg CPG_MOD 922>;
826
827	ports {
828		#address-cells = <1>;
829		#size-cells = <0>;
830		rsnd_port0: port@0 {
831			reg = <0>;
832			rsnd_endpoint0: endpoint {
833				remote-endpoint = <&ak4613_endpoint>;
834
835				dai-format = "left_j";
836				bitclock-master = <&rsnd_endpoint0>;
837				frame-master = <&rsnd_endpoint0>;
838
839				playback = <&ssi0>, <&src0>, <&dvc0>;
840				capture = <&ssi1>, <&src1>, <&dvc1>;
841			};
842		};
843
844		rsnd_port1: port@1 {
845			reg = <1>;
846			rsnd_endpoint1: endpoint {
847				remote-endpoint = <&dw_hdmi0_snd_in>;
848
849				dai-format = "i2s";
850				bitclock-master = <&rsnd_endpoint1>;
851				frame-master = <&rsnd_endpoint1>;
852
853				playback = <&ssi2>;
854			};
855		};
856
857#ifdef SOC_HAS_HDMI1
858		rsnd_port2: port@2 {
859			reg = <2>;
860			rsnd_endpoint2: endpoint {
861				remote-endpoint = <&dw_hdmi1_snd_in>;
862
863				dai-format = "i2s";
864				bitclock-master = <&rsnd_endpoint2>;
865				frame-master = <&rsnd_endpoint2>;
866
867				playback = <&ssi3>;
868			};
869		};
870#endif /* SOC_HAS_HDMI1 */
871	};
872};
873
874&rpc {
875	/* Left disabled.  To be enabled by firmware when unlocked. */
876
877	flash@0 {
878		compatible = "cypress,hyperflash", "cfi-flash";
879		reg = <0>;
880
881		partitions {
882			compatible = "fixed-partitions";
883			#address-cells = <1>;
884			#size-cells = <1>;
885
886			bootparam@0 {
887				reg = <0x00000000 0x040000>;
888				read-only;
889			};
890			bl2@40000 {
891				reg = <0x00040000 0x140000>;
892				read-only;
893			};
894			cert_header_sa6@180000 {
895				reg = <0x00180000 0x040000>;
896				read-only;
897			};
898			bl31@1c0000 {
899				reg = <0x001c0000 0x040000>;
900				read-only;
901			};
902			tee@200000 {
903				reg = <0x00200000 0x440000>;
904				read-only;
905			};
906			uboot@640000 {
907				reg = <0x00640000 0x100000>;
908				read-only;
909			};
910			dtb@740000 {
911				reg = <0x00740000 0x080000>;
912			};
913			kernel@7c0000 {
914				reg = <0x007c0000 0x1400000>;
915			};
916			user@1bc0000 {
917				reg = <0x01bc0000 0x2440000>;
918			};
919		};
920	};
921};
922
923&rwdt {
924	timeout-sec = <60>;
925	status = "okay";
926};
927
928#ifdef SOC_HAS_SATA
929&sata {
930	status = "okay";
931};
932#endif /* SOC_HAS_SATA */
933
934&scif1 {
935	pinctrl-0 = <&scif1_pins>;
936	pinctrl-names = "default";
937
938	uart-has-rtscts;
939	/* Please only enable hscif1 or scif1 */
940	/* status = "okay"; */
941};
942
943&scif2 {
944	pinctrl-0 = <&scif2_pins>;
945	pinctrl-names = "default";
946
947	status = "okay";
948};
949
950&scif_clk {
951	clock-frequency = <14745600>;
952};
953
954&sdhi0 {
955	pinctrl-0 = <&sdhi0_pins>;
956	pinctrl-1 = <&sdhi0_pins_uhs>;
957	pinctrl-names = "default", "state_uhs";
958
959	vmmc-supply = <&vcc_sdhi0>;
960	vqmmc-supply = <&vccq_sdhi0>;
961	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
962	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
963	bus-width = <4>;
964	sd-uhs-sdr50;
965	sd-uhs-sdr104;
966	status = "okay";
967};
968
969&sdhi2 {
970	/* used for on-board 8bit eMMC */
971	pinctrl-0 = <&sdhi2_pins>;
972	pinctrl-1 = <&sdhi2_pins>;
973	pinctrl-names = "default", "state_uhs";
974
975	vmmc-supply = <&reg_3p3v>;
976	vqmmc-supply = <&reg_1p8v>;
977	bus-width = <8>;
978	mmc-hs200-1_8v;
979	mmc-hs400-1_8v;
980	no-sd;
981	no-sdio;
982	non-removable;
983	fixed-emmc-driver-type = <1>;
984	full-pwr-cycle-in-suspend;
985	status = "okay";
986};
987
988&sdhi3 {
989	pinctrl-0 = <&sdhi3_pins>;
990	pinctrl-1 = <&sdhi3_pins_uhs>;
991	pinctrl-names = "default", "state_uhs";
992
993	vmmc-supply = <&vcc_sdhi3>;
994	vqmmc-supply = <&vccq_sdhi3>;
995	cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
996	wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
997	bus-width = <4>;
998	sd-uhs-sdr50;
999	sd-uhs-sdr104;
1000	status = "okay";
1001};
1002
1003&ssi1 {
1004	shared-pin;
1005};
1006
1007&usb_extal_clk {
1008	clock-frequency = <50000000>;
1009};
1010
1011&usb2_phy0 {
1012	pinctrl-0 = <&usb0_pins>;
1013	pinctrl-names = "default";
1014
1015	vbus-supply = <&vbus0_usb2>;
1016	status = "okay";
1017};
1018
1019&usb2_phy1 {
1020	pinctrl-0 = <&usb1_pins>;
1021	pinctrl-names = "default";
1022
1023	status = "okay";
1024};
1025
1026&usb3_peri0 {
1027	phys = <&usb3_phy0>;
1028	phy-names = "usb";
1029
1030	companion = <&xhci0>;
1031
1032	status = "okay";
1033};
1034
1035&usb3_phy0 {
1036	status = "okay";
1037};
1038
1039&usb3s0_clk {
1040	clock-frequency = <100000000>;
1041};
1042
1043&vin0 {
1044	status = "okay";
1045};
1046
1047&vin1 {
1048	status = "okay";
1049};
1050
1051&vin2 {
1052	status = "okay";
1053};
1054
1055&vin3 {
1056	status = "okay";
1057};
1058
1059&vin4 {
1060	status = "okay";
1061};
1062
1063&vin5 {
1064	status = "okay";
1065};
1066
1067&vin6 {
1068	status = "okay";
1069};
1070
1071&vin7 {
1072	status = "okay";
1073};
1074
1075&xhci0 {
1076	pinctrl-0 = <&usb30_pins>;
1077	pinctrl-names = "default";
1078
1079	status = "okay";
1080};
1081
1082#ifdef SOC_HAS_USB2_CH2
1083&ehci2 {
1084	status = "okay";
1085};
1086
1087&ohci2 {
1088	status = "okay";
1089};
1090
1091&pfc {
1092	usb2_pins: usb2 {
1093		groups = "usb2";
1094		function = "usb2";
1095	};
1096};
1097
1098&usb2_phy2 {
1099	pinctrl-0 = <&usb2_pins>;
1100	pinctrl-names = "default";
1101
1102	status = "okay";
1103};
1104#endif /* SOC_HAS_USB2_CH2 */
1105