1// SPDX-License-Identifier: GPL-2.0 2/* 3 * Device Tree Source for common parts of Salvator-X board variants 4 * 5 * Copyright (C) 2015-2016 Renesas Electronics Corp. 6 */ 7 8/* 9 * SSI-AK4613 10 * 11 * This command is required when Playback/Capture 12 * 13 * amixer set "DVC Out" 100% 14 * amixer set "DVC In" 100% 15 * 16 * You can use Mute 17 * 18 * amixer set "DVC Out Mute" on 19 * amixer set "DVC In Mute" on 20 * 21 * You can use Volume Ramp 22 * 23 * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps" 24 * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps" 25 * amixer set "DVC Out Ramp" on 26 * aplay xxx.wav & 27 * amixer set "DVC Out" 80% // Volume Down 28 * amixer set "DVC Out" 100% // Volume Up 29 */ 30 31#include <dt-bindings/gpio/gpio.h> 32#include <dt-bindings/input/input.h> 33 34/ { 35 aliases { 36 serial0 = &scif2; 37 serial1 = &hscif1; 38 ethernet0 = &avb; 39 mmc0 = &sdhi2; 40 mmc1 = &sdhi0; 41 mmc2 = &sdhi3; 42 }; 43 44 chosen { 45 bootargs = "ignore_loglevel rw root=/dev/nfs ip=on"; 46 stdout-path = "serial0:115200n8"; 47 }; 48 49 audio_clkout: audio-clkout { 50 /* 51 * This is same as <&rcar_sound 0> 52 * but needed to avoid cs2000/rcar_sound probe dead-lock 53 */ 54 compatible = "fixed-clock"; 55 #clock-cells = <0>; 56 clock-frequency = <12288000>; 57 }; 58 59 backlight: backlight { 60 compatible = "pwm-backlight"; 61 pwms = <&pwm1 0 50000>; 62 63 brightness-levels = <256 128 64 16 8 4 0>; 64 default-brightness-level = <6>; 65 66 power-supply = <®_12v>; 67 enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; 68 }; 69 70 cvbs-in { 71 compatible = "composite-video-connector"; 72 label = "CVBS IN"; 73 74 port { 75 cvbs_con: endpoint { 76 remote-endpoint = <&adv7482_ain7>; 77 }; 78 }; 79 }; 80 81 hdmi-in { 82 compatible = "hdmi-connector"; 83 label = "HDMI IN"; 84 type = "a"; 85 86 port { 87 hdmi_in_con: endpoint { 88 remote-endpoint = <&adv7482_hdmi>; 89 }; 90 }; 91 }; 92 93 hdmi0-out { 94 compatible = "hdmi-connector"; 95 label = "HDMI0 OUT"; 96 type = "a"; 97 98 port { 99 hdmi0_con: endpoint { 100 }; 101 }; 102 }; 103 104 hdmi1-out { 105 compatible = "hdmi-connector"; 106 label = "HDMI1 OUT"; 107 type = "a"; 108 109 port { 110 hdmi1_con: endpoint { 111 }; 112 }; 113 }; 114 115 keys { 116 compatible = "gpio-keys"; 117 118 pinctrl-0 = <&keys_pins>; 119 pinctrl-names = "default"; 120 121 key-1 { 122 gpios = <&gpio5 17 GPIO_ACTIVE_LOW>; 123 linux,code = <KEY_1>; 124 label = "SW4-1"; 125 wakeup-source; 126 debounce-interval = <20>; 127 }; 128 key-2 { 129 gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; 130 linux,code = <KEY_2>; 131 label = "SW4-2"; 132 wakeup-source; 133 debounce-interval = <20>; 134 }; 135 key-3 { 136 gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; 137 linux,code = <KEY_3>; 138 label = "SW4-3"; 139 wakeup-source; 140 debounce-interval = <20>; 141 }; 142 key-4 { 143 gpios = <&gpio5 23 GPIO_ACTIVE_LOW>; 144 linux,code = <KEY_4>; 145 label = "SW4-4"; 146 wakeup-source; 147 debounce-interval = <20>; 148 }; 149 key-a { 150 gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; 151 linux,code = <KEY_A>; 152 label = "TSW0"; 153 wakeup-source; 154 debounce-interval = <20>; 155 }; 156 key-b { 157 gpios = <&gpio6 12 GPIO_ACTIVE_LOW>; 158 linux,code = <KEY_B>; 159 label = "TSW1"; 160 wakeup-source; 161 debounce-interval = <20>; 162 }; 163 key-c { 164 gpios = <&gpio6 13 GPIO_ACTIVE_LOW>; 165 linux,code = <KEY_C>; 166 label = "TSW2"; 167 wakeup-source; 168 debounce-interval = <20>; 169 }; 170 }; 171 172 reg_1p8v: regulator0 { 173 compatible = "regulator-fixed"; 174 regulator-name = "fixed-1.8V"; 175 regulator-min-microvolt = <1800000>; 176 regulator-max-microvolt = <1800000>; 177 regulator-boot-on; 178 regulator-always-on; 179 }; 180 181 reg_3p3v: regulator1 { 182 compatible = "regulator-fixed"; 183 regulator-name = "fixed-3.3V"; 184 regulator-min-microvolt = <3300000>; 185 regulator-max-microvolt = <3300000>; 186 regulator-boot-on; 187 regulator-always-on; 188 }; 189 190 reg_12v: regulator2 { 191 compatible = "regulator-fixed"; 192 regulator-name = "fixed-12V"; 193 regulator-min-microvolt = <12000000>; 194 regulator-max-microvolt = <12000000>; 195 regulator-boot-on; 196 regulator-always-on; 197 }; 198 199 sound_card: sound { 200 compatible = "audio-graph-card"; 201 202 label = "rcar-sound"; 203 204 dais = <&rsnd_port0 /* ak4613 */ 205 &rsnd_port1>; /* HDMI0 */ 206 }; 207 208 vbus0_usb2: regulator-vbus0-usb2 { 209 compatible = "regulator-fixed"; 210 211 regulator-name = "USB20_VBUS0"; 212 regulator-min-microvolt = <5000000>; 213 regulator-max-microvolt = <5000000>; 214 215 gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>; 216 enable-active-high; 217 }; 218 219 vcc_sdhi0: regulator-vcc-sdhi0 { 220 compatible = "regulator-fixed"; 221 222 regulator-name = "SDHI0 Vcc"; 223 regulator-min-microvolt = <3300000>; 224 regulator-max-microvolt = <3300000>; 225 226 gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>; 227 enable-active-high; 228 }; 229 230 vccq_sdhi0: regulator-vccq-sdhi0 { 231 compatible = "regulator-gpio"; 232 233 regulator-name = "SDHI0 VccQ"; 234 regulator-min-microvolt = <1800000>; 235 regulator-max-microvolt = <3300000>; 236 237 gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; 238 gpios-states = <1>; 239 states = <3300000 1>, <1800000 0>; 240 }; 241 242 vcc_sdhi3: regulator-vcc-sdhi3 { 243 compatible = "regulator-fixed"; 244 245 regulator-name = "SDHI3 Vcc"; 246 regulator-min-microvolt = <3300000>; 247 regulator-max-microvolt = <3300000>; 248 249 gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>; 250 enable-active-high; 251 }; 252 253 vccq_sdhi3: regulator-vccq-sdhi3 { 254 compatible = "regulator-gpio"; 255 256 regulator-name = "SDHI3 VccQ"; 257 regulator-min-microvolt = <1800000>; 258 regulator-max-microvolt = <3300000>; 259 260 gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; 261 gpios-states = <1>; 262 states = <3300000 1>, <1800000 0>; 263 }; 264 265 vga { 266 compatible = "vga-connector"; 267 268 port { 269 vga_in: endpoint { 270 remote-endpoint = <&adv7123_out>; 271 }; 272 }; 273 }; 274 275 vga-encoder { 276 compatible = "adi,adv7123"; 277 278 ports { 279 #address-cells = <1>; 280 #size-cells = <0>; 281 282 port@0 { 283 reg = <0>; 284 adv7123_in: endpoint { 285 remote-endpoint = <&du_out_rgb>; 286 }; 287 }; 288 port@1 { 289 reg = <1>; 290 adv7123_out: endpoint { 291 remote-endpoint = <&vga_in>; 292 }; 293 }; 294 }; 295 }; 296 297 x12_clk: x12 { 298 compatible = "fixed-clock"; 299 #clock-cells = <0>; 300 clock-frequency = <24576000>; 301 }; 302 303 /* External DU dot clocks */ 304 x21_clk: x21-clock { 305 compatible = "fixed-clock"; 306 #clock-cells = <0>; 307 clock-frequency = <33000000>; 308 }; 309 310 x22_clk: x22-clock { 311 compatible = "fixed-clock"; 312 #clock-cells = <0>; 313 clock-frequency = <33000000>; 314 }; 315 316 x23_clk: x23-clock { 317 compatible = "fixed-clock"; 318 #clock-cells = <0>; 319 clock-frequency = <25000000>; 320 }; 321}; 322 323&a57_0 { 324 cpu-supply = <&dvfs>; 325}; 326 327&audio_clk_a { 328 clock-frequency = <22579200>; 329}; 330 331&avb { 332 pinctrl-0 = <&avb_pins>; 333 pinctrl-names = "default"; 334 phy-handle = <&phy0>; 335 tx-internal-delay-ps = <2000>; 336 status = "okay"; 337 338 phy0: ethernet-phy@0 { 339 rxc-skew-ps = <1500>; 340 reg = <0>; 341 interrupt-parent = <&gpio2>; 342 interrupts = <11 IRQ_TYPE_LEVEL_LOW>; 343 reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; 344 }; 345}; 346 347&csi20 { 348 status = "okay"; 349 350 ports { 351 port@0 { 352 reg = <0>; 353 csi20_in: endpoint { 354 clock-lanes = <0>; 355 data-lanes = <1>; 356 remote-endpoint = <&adv7482_txb>; 357 }; 358 }; 359 }; 360}; 361 362&csi40 { 363 status = "okay"; 364 365 ports { 366 port@0 { 367 reg = <0>; 368 369 csi40_in: endpoint { 370 clock-lanes = <0>; 371 data-lanes = <1 2 3 4>; 372 remote-endpoint = <&adv7482_txa>; 373 }; 374 }; 375 }; 376}; 377 378&du { 379 pinctrl-0 = <&du_pins>; 380 pinctrl-names = "default"; 381 status = "okay"; 382 383 ports { 384 port@0 { 385 endpoint { 386 remote-endpoint = <&adv7123_in>; 387 }; 388 }; 389 }; 390}; 391 392&ehci0 { 393 dr_mode = "otg"; 394 status = "okay"; 395}; 396 397&ehci1 { 398 status = "okay"; 399}; 400 401&extalr_clk { 402 clock-frequency = <32768>; 403}; 404 405&hdmi0 { 406 status = "okay"; 407 408 ports { 409 port@1 { 410 reg = <1>; 411 rcar_dw_hdmi0_out: endpoint { 412 remote-endpoint = <&hdmi0_con>; 413 }; 414 }; 415 port@2 { 416 reg = <2>; 417 dw_hdmi0_snd_in: endpoint { 418 remote-endpoint = <&rsnd_endpoint1>; 419 }; 420 }; 421 }; 422}; 423 424&hdmi0_con { 425 remote-endpoint = <&rcar_dw_hdmi0_out>; 426}; 427 428&hscif1 { 429 pinctrl-0 = <&hscif1_pins>; 430 pinctrl-names = "default"; 431 432 uart-has-rtscts; 433 /* Please only enable hscif1 or scif1 */ 434 status = "okay"; 435}; 436 437&hsusb { 438 dr_mode = "otg"; 439 status = "okay"; 440}; 441 442&i2c2 { 443 pinctrl-0 = <&i2c2_pins>; 444 pinctrl-names = "default"; 445 446 status = "okay"; 447 448 clock-frequency = <100000>; 449 450 ak4613: codec@10 { 451 compatible = "asahi-kasei,ak4613"; 452 #sound-dai-cells = <0>; 453 reg = <0x10>; 454 clocks = <&rcar_sound 3>; 455 456 asahi-kasei,in1-single-end; 457 asahi-kasei,in2-single-end; 458 asahi-kasei,out1-single-end; 459 asahi-kasei,out2-single-end; 460 asahi-kasei,out3-single-end; 461 asahi-kasei,out4-single-end; 462 asahi-kasei,out5-single-end; 463 asahi-kasei,out6-single-end; 464 465 port { 466 ak4613_endpoint: endpoint { 467 remote-endpoint = <&rsnd_endpoint0>; 468 }; 469 }; 470 }; 471 472 cs2000: clk_multiplier@4f { 473 #clock-cells = <0>; 474 compatible = "cirrus,cs2000-cp"; 475 reg = <0x4f>; 476 clocks = <&audio_clkout>, <&x12_clk>; 477 clock-names = "clk_in", "ref_clk"; 478 479 assigned-clocks = <&cs2000>; 480 assigned-clock-rates = <24576000>; /* 1/1 divide */ 481 }; 482}; 483 484&i2c4 { 485 status = "okay"; 486 487 pca9654: gpio@20 { 488 compatible = "onnn,pca9654"; 489 reg = <0x20>; 490 gpio-controller; 491 #gpio-cells = <2>; 492 }; 493 494 video-receiver@70 { 495 compatible = "adi,adv7482"; 496 reg = <0x70 0x71 0x72 0x73 0x74 0x75 497 0x60 0x61 0x62 0x63 0x64 0x65>; 498 reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater", 499 "infoframe", "cbus", "cec", "sdp", "txa", "txb" ; 500 501 #address-cells = <1>; 502 #size-cells = <0>; 503 504 interrupt-parent = <&gpio6>; 505 interrupt-names = "intrq1", "intrq2"; 506 interrupts = <30 IRQ_TYPE_LEVEL_LOW>, 507 <31 IRQ_TYPE_LEVEL_LOW>; 508 509 port@7 { 510 reg = <7>; 511 512 adv7482_ain7: endpoint { 513 remote-endpoint = <&cvbs_con>; 514 }; 515 }; 516 517 port@8 { 518 reg = <8>; 519 520 adv7482_hdmi: endpoint { 521 remote-endpoint = <&hdmi_in_con>; 522 }; 523 }; 524 525 port@a { 526 reg = <10>; 527 528 adv7482_txa: endpoint { 529 clock-lanes = <0>; 530 data-lanes = <1 2 3 4>; 531 remote-endpoint = <&csi40_in>; 532 }; 533 }; 534 535 port@b { 536 reg = <11>; 537 538 adv7482_txb: endpoint { 539 clock-lanes = <0>; 540 data-lanes = <1>; 541 remote-endpoint = <&csi20_in>; 542 }; 543 }; 544 }; 545 546 csa_vdd: adc@7c { 547 compatible = "maxim,max9611"; 548 reg = <0x7c>; 549 550 shunt-resistor-micro-ohms = <5000>; 551 }; 552 553 csa_dvfs: adc@7f { 554 compatible = "maxim,max9611"; 555 reg = <0x7f>; 556 557 shunt-resistor-micro-ohms = <5000>; 558 }; 559}; 560 561&i2c_dvfs { 562 status = "okay"; 563 564 clock-frequency = <400000>; 565 566 pmic: pmic@30 { 567 pinctrl-0 = <&irq0_pins>; 568 pinctrl-names = "default"; 569 570 compatible = "rohm,bd9571mwv"; 571 reg = <0x30>; 572 interrupt-parent = <&intc_ex>; 573 interrupts = <0 IRQ_TYPE_LEVEL_LOW>; 574 interrupt-controller; 575 #interrupt-cells = <2>; 576 gpio-controller; 577 #gpio-cells = <2>; 578 rohm,ddr-backup-power = <0xf>; 579 rohm,rstbmode-level; 580 581 regulators { 582 dvfs: dvfs { 583 regulator-name = "dvfs"; 584 regulator-min-microvolt = <750000>; 585 regulator-max-microvolt = <1030000>; 586 regulator-boot-on; 587 regulator-always-on; 588 }; 589 }; 590 }; 591 592 eeprom@50 { 593 compatible = "rohm,br24t01", "atmel,24c01"; 594 reg = <0x50>; 595 pagesize = <8>; 596 }; 597}; 598 599&ohci0 { 600 dr_mode = "otg"; 601 status = "okay"; 602}; 603 604&ohci1 { 605 status = "okay"; 606}; 607 608&pcie_bus_clk { 609 clock-frequency = <100000000>; 610}; 611 612&pciec0 { 613 status = "okay"; 614}; 615 616&pciec1 { 617 status = "okay"; 618}; 619 620&pfc { 621 pinctrl-0 = <&scif_clk_pins>; 622 pinctrl-names = "default"; 623 624 avb_pins: avb { 625 mux { 626 groups = "avb_link", "avb_mdio", "avb_mii"; 627 function = "avb"; 628 }; 629 630 pins_mdio { 631 groups = "avb_mdio"; 632 drive-strength = <24>; 633 }; 634 635 pins_mii_tx { 636 pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0", 637 "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3"; 638 drive-strength = <12>; 639 }; 640 }; 641 642 du_pins: du { 643 groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0"; 644 function = "du"; 645 }; 646 647 hscif1_pins: hscif1 { 648 groups = "hscif1_data_a", "hscif1_ctrl_a"; 649 function = "hscif1"; 650 }; 651 652 i2c2_pins: i2c2 { 653 groups = "i2c2_a"; 654 function = "i2c2"; 655 }; 656 657 irq0_pins: irq0 { 658 groups = "intc_ex_irq0"; 659 function = "intc_ex"; 660 }; 661 662 keys_pins: keys { 663 pins = "GP_5_17", "GP_5_20", "GP_5_22"; 664 bias-pull-up; 665 }; 666 667 pwm1_pins: pwm1 { 668 groups = "pwm1_a"; 669 function = "pwm1"; 670 }; 671 672 scif1_pins: scif1 { 673 groups = "scif1_data_a", "scif1_ctrl"; 674 function = "scif1"; 675 }; 676 677 scif2_pins: scif2 { 678 groups = "scif2_data_a"; 679 function = "scif2"; 680 }; 681 682 scif_clk_pins: scif_clk { 683 groups = "scif_clk_a"; 684 function = "scif_clk"; 685 }; 686 687 sdhi0_pins: sd0 { 688 groups = "sdhi0_data4", "sdhi0_ctrl"; 689 function = "sdhi0"; 690 power-source = <3300>; 691 }; 692 693 sdhi0_pins_uhs: sd0_uhs { 694 groups = "sdhi0_data4", "sdhi0_ctrl"; 695 function = "sdhi0"; 696 power-source = <1800>; 697 }; 698 699 sdhi2_pins: sd2 { 700 groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds"; 701 function = "sdhi2"; 702 power-source = <1800>; 703 }; 704 705 sdhi3_pins: sd3 { 706 groups = "sdhi3_data4", "sdhi3_ctrl"; 707 function = "sdhi3"; 708 power-source = <3300>; 709 }; 710 711 sdhi3_pins_uhs: sd3_uhs { 712 groups = "sdhi3_data4", "sdhi3_ctrl"; 713 function = "sdhi3"; 714 power-source = <1800>; 715 }; 716 717 sound_pins: sound { 718 groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a"; 719 function = "ssi"; 720 }; 721 722 sound_clk_pins: sound_clk { 723 groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a", 724 "audio_clkout_a", "audio_clkout3_a"; 725 function = "audio_clk"; 726 }; 727 728 usb0_pins: usb0 { 729 groups = "usb0"; 730 function = "usb0"; 731 }; 732 733 usb1_pins: usb1 { 734 mux { 735 groups = "usb1"; 736 function = "usb1"; 737 }; 738 739 ovc { 740 pins = "GP_6_27"; 741 bias-pull-up; 742 }; 743 744 pwen { 745 pins = "GP_6_26"; 746 bias-pull-down; 747 }; 748 }; 749 750 usb30_pins: usb30 { 751 groups = "usb30"; 752 function = "usb30"; 753 }; 754}; 755 756&pwm1 { 757 pinctrl-0 = <&pwm1_pins>; 758 pinctrl-names = "default"; 759 760 status = "okay"; 761}; 762 763&rcar_sound { 764 pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; 765 pinctrl-names = "default"; 766 767 /* Single DAI */ 768 #sound-dai-cells = <0>; 769 770 /* audio_clkout0/1/2/3 */ 771 #clock-cells = <1>; 772 clock-frequency = <12288000 11289600>; 773 774 status = "okay"; 775 776 /* update <audio_clk_b> to <cs2000> */ 777 clocks = <&cpg CPG_MOD 1005>, 778 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, 779 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, 780 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, 781 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, 782 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, 783 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, 784 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, 785 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, 786 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, 787 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, 788 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, 789 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, 790 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, 791 <&audio_clk_a>, <&cs2000>, 792 <&audio_clk_c>, 793 <&cpg CPG_CORE CPG_AUDIO_CLK_I>; 794 795 ports { 796 #address-cells = <1>; 797 #size-cells = <0>; 798 rsnd_port0: port@0 { 799 reg = <0>; 800 rsnd_endpoint0: endpoint { 801 remote-endpoint = <&ak4613_endpoint>; 802 803 dai-format = "left_j"; 804 bitclock-master = <&rsnd_endpoint0>; 805 frame-master = <&rsnd_endpoint0>; 806 807 playback = <&ssi0>, <&src0>, <&dvc0>; 808 capture = <&ssi1>, <&src1>, <&dvc1>; 809 }; 810 }; 811 812 rsnd_port1: port@1 { 813 reg = <1>; 814 rsnd_endpoint1: endpoint { 815 remote-endpoint = <&dw_hdmi0_snd_in>; 816 817 dai-format = "i2s"; 818 bitclock-master = <&rsnd_endpoint1>; 819 frame-master = <&rsnd_endpoint1>; 820 821 playback = <&ssi2>; 822 }; 823 }; 824 }; 825}; 826 827&rwdt { 828 timeout-sec = <60>; 829 status = "okay"; 830}; 831 832&scif1 { 833 pinctrl-0 = <&scif1_pins>; 834 pinctrl-names = "default"; 835 836 uart-has-rtscts; 837 /* Please only enable hscif1 or scif1 */ 838 /* status = "okay"; */ 839}; 840 841&scif2 { 842 pinctrl-0 = <&scif2_pins>; 843 pinctrl-names = "default"; 844 845 status = "okay"; 846}; 847 848&scif_clk { 849 clock-frequency = <14745600>; 850}; 851 852&sdhi0 { 853 pinctrl-0 = <&sdhi0_pins>; 854 pinctrl-1 = <&sdhi0_pins_uhs>; 855 pinctrl-names = "default", "state_uhs"; 856 857 vmmc-supply = <&vcc_sdhi0>; 858 vqmmc-supply = <&vccq_sdhi0>; 859 cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; 860 wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; 861 bus-width = <4>; 862 sd-uhs-sdr50; 863 sd-uhs-sdr104; 864 status = "okay"; 865}; 866 867&sdhi2 { 868 /* used for on-board 8bit eMMC */ 869 pinctrl-0 = <&sdhi2_pins>; 870 pinctrl-1 = <&sdhi2_pins>; 871 pinctrl-names = "default", "state_uhs"; 872 873 vmmc-supply = <®_3p3v>; 874 vqmmc-supply = <®_1p8v>; 875 bus-width = <8>; 876 mmc-hs200-1_8v; 877 mmc-hs400-1_8v; 878 no-sd; 879 no-sdio; 880 non-removable; 881 fixed-emmc-driver-type = <1>; 882 full-pwr-cycle-in-suspend; 883 status = "okay"; 884}; 885 886&sdhi3 { 887 pinctrl-0 = <&sdhi3_pins>; 888 pinctrl-1 = <&sdhi3_pins_uhs>; 889 pinctrl-names = "default", "state_uhs"; 890 891 vmmc-supply = <&vcc_sdhi3>; 892 vqmmc-supply = <&vccq_sdhi3>; 893 cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; 894 wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>; 895 bus-width = <4>; 896 sd-uhs-sdr50; 897 sd-uhs-sdr104; 898 status = "okay"; 899}; 900 901&ssi1 { 902 shared-pin; 903}; 904 905&usb_extal_clk { 906 clock-frequency = <50000000>; 907}; 908 909&usb2_phy0 { 910 pinctrl-0 = <&usb0_pins>; 911 pinctrl-names = "default"; 912 913 vbus-supply = <&vbus0_usb2>; 914 status = "okay"; 915}; 916 917&usb2_phy1 { 918 pinctrl-0 = <&usb1_pins>; 919 pinctrl-names = "default"; 920 921 status = "okay"; 922}; 923 924&usb3_peri0 { 925 phys = <&usb3_phy0>; 926 phy-names = "usb"; 927 928 companion = <&xhci0>; 929 930 status = "okay"; 931}; 932 933&usb3_phy0 { 934 status = "okay"; 935}; 936 937&usb3s0_clk { 938 clock-frequency = <100000000>; 939}; 940 941&vin0 { 942 status = "okay"; 943}; 944 945&vin1 { 946 status = "okay"; 947}; 948 949&vin2 { 950 status = "okay"; 951}; 952 953&vin3 { 954 status = "okay"; 955}; 956 957&vin4 { 958 status = "okay"; 959}; 960 961&vin5 { 962 status = "okay"; 963}; 964 965&vin6 { 966 status = "okay"; 967}; 968 969&vin7 { 970 status = "okay"; 971}; 972 973&xhci0 { 974 pinctrl-0 = <&usb30_pins>; 975 pinctrl-names = "default"; 976 977 status = "okay"; 978}; 979