1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2020-2021, Linaro Limited 4 */ 5 6/dts-v1/; 7 8#include <dt-bindings/regulator/qcom,rpmh-regulator.h> 9#include "sm8350.dtsi" 10#include "pm8350.dtsi" 11#include "pm8350b.dtsi" 12#include "pm8350c.dtsi" 13#include "pmk8350.dtsi" 14#include "pmr735a.dtsi" 15#include "pmr735b.dtsi" 16 17/ { 18 model = "Qualcomm Technologies, Inc. SM8350 HDK"; 19 compatible = "qcom,sm8350-hdk", "qcom,sm8350"; 20 chassis-type = "embedded"; 21 22 aliases { 23 serial0 = &uart2; 24 }; 25 26 chosen { 27 stdout-path = "serial0:115200n8"; 28 }; 29 30 hdmi-connector { 31 compatible = "hdmi-connector"; 32 type = "a"; 33 34 port { 35 hdmi_con: endpoint { 36 remote-endpoint = <<9611_out>; 37 }; 38 }; 39 }; 40 41 pmic-glink { 42 compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink"; 43 #address-cells = <1>; 44 #size-cells = <0>; 45 orientation-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>; 46 47 connector@0 { 48 compatible = "usb-c-connector"; 49 reg = <0>; 50 power-role = "dual"; 51 data-role = "dual"; 52 53 ports { 54 #address-cells = <1>; 55 #size-cells = <0>; 56 57 port@0 { 58 reg = <0>; 59 60 pmic_glink_hs_in: endpoint { 61 remote-endpoint = <&usb_1_dwc3_hs>; 62 }; 63 }; 64 65 port@1 { 66 reg = <1>; 67 68 pmic_glink_ss_in: endpoint { 69 remote-endpoint = <&usb_1_qmpphy_out>; 70 }; 71 }; 72 73 port@2 { 74 reg = <2>; 75 76 pmic_glink_sbu: endpoint { 77 remote-endpoint = <&fsa4480_sbu_mux>; 78 }; 79 }; 80 }; 81 }; 82 }; 83 84 vph_pwr: vph-pwr-regulator { 85 compatible = "regulator-fixed"; 86 regulator-name = "vph_pwr"; 87 regulator-min-microvolt = <3700000>; 88 regulator-max-microvolt = <3700000>; 89 90 regulator-always-on; 91 regulator-boot-on; 92 }; 93 94 lt9611_1v2: lt9611-1v2-regulator { 95 compatible = "regulator-fixed"; 96 regulator-name = "LT9611_1V2"; 97 98 vin-supply = <&vph_pwr>; 99 regulator-min-microvolt = <1200000>; 100 regulator-max-microvolt = <1200000>; 101 gpio = <&tlmm 49 GPIO_ACTIVE_HIGH>; 102 enable-active-high; 103 regulator-boot-on; 104 }; 105 106 lt9611_3v3: lt9611-3v3-regulator { 107 compatible = "regulator-fixed"; 108 regulator-name = "LT9611_3V3"; 109 110 vin-supply = <&vreg_bob>; 111 gpio = <&tlmm 47 GPIO_ACTIVE_HIGH>; 112 regulator-min-microvolt = <3300000>; 113 regulator-max-microvolt = <3300000>; 114 enable-active-high; 115 regulator-boot-on; 116 regulator-always-on; 117 }; 118}; 119 120&adsp { 121 status = "okay"; 122 firmware-name = "qcom/sm8350/adsp.mbn"; 123}; 124 125&apps_rsc { 126 regulators-0 { 127 compatible = "qcom,pm8350-rpmh-regulators"; 128 qcom,pmic-id = "b"; 129 130 vdd-s1-supply = <&vph_pwr>; 131 vdd-s2-supply = <&vph_pwr>; 132 vdd-s3-supply = <&vph_pwr>; 133 vdd-s4-supply = <&vph_pwr>; 134 vdd-s5-supply = <&vph_pwr>; 135 vdd-s6-supply = <&vph_pwr>; 136 vdd-s7-supply = <&vph_pwr>; 137 vdd-s8-supply = <&vph_pwr>; 138 vdd-s9-supply = <&vph_pwr>; 139 vdd-s10-supply = <&vph_pwr>; 140 vdd-s11-supply = <&vph_pwr>; 141 vdd-s12-supply = <&vph_pwr>; 142 143 vdd-l1-l4-supply = <&vreg_s11b_0p95>; 144 vdd-l2-l7-supply = <&vreg_bob>; 145 vdd-l3-l5-supply = <&vreg_bob>; 146 vdd-l6-l9-l10-supply = <&vreg_s11b_0p95>; 147 148 vreg_s10b_1p8: smps10 { 149 regulator-name = "vreg_s10b_1p8"; 150 regulator-min-microvolt = <1800000>; 151 regulator-max-microvolt = <1800000>; 152 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 153 }; 154 155 vreg_s11b_0p95: smps11 { 156 regulator-name = "vreg_s11b_0p95"; 157 regulator-min-microvolt = <952000>; 158 regulator-max-microvolt = <952000>; 159 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 160 }; 161 162 vreg_s12b_1p25: smps12 { 163 regulator-name = "vreg_s12b_1p25"; 164 regulator-min-microvolt = <1256000>; 165 regulator-max-microvolt = <1256000>; 166 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 167 }; 168 169 vreg_l1b_0p88: ldo1 { 170 regulator-name = "vreg_l1b_0p88"; 171 regulator-min-microvolt = <912000>; 172 regulator-max-microvolt = <920000>; 173 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 174 }; 175 176 vreg_l2b_3p07: ldo2 { 177 regulator-name = "vreg_l2b_3p07"; 178 regulator-min-microvolt = <3072000>; 179 regulator-max-microvolt = <3072000>; 180 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 181 }; 182 183 vreg_l3b_0p9: ldo3 { 184 regulator-name = "vreg_l3b_0p9"; 185 regulator-min-microvolt = <904000>; 186 regulator-max-microvolt = <904000>; 187 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 188 }; 189 190 vreg_l5b_0p88: ldo5 { 191 regulator-name = "vreg_l5b_0p88"; 192 regulator-min-microvolt = <880000>; 193 regulator-max-microvolt = <888000>; 194 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 195 regulator-allow-set-load; 196 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 197 RPMH_REGULATOR_MODE_HPM>; 198 }; 199 200 vreg_l6b_1p2: ldo6 { 201 regulator-name = "vreg_l6b_1p2"; 202 regulator-min-microvolt = <1200000>; 203 regulator-max-microvolt = <1208000>; 204 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 205 regulator-allow-set-load; 206 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 207 RPMH_REGULATOR_MODE_HPM>; 208 }; 209 210 vreg_l7b_2p96: ldo7 { 211 regulator-name = "vreg_l7b_2p96"; 212 regulator-min-microvolt = <2504000>; 213 regulator-max-microvolt = <2504000>; 214 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 215 regulator-allow-set-load; 216 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 217 RPMH_REGULATOR_MODE_HPM>; 218 }; 219 220 vreg_l9b_1p2: ldo9 { 221 regulator-name = "vreg_l9b_1p2"; 222 regulator-min-microvolt = <1200000>; 223 regulator-max-microvolt = <1200000>; 224 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 225 regulator-allow-set-load; 226 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 227 RPMH_REGULATOR_MODE_HPM>; 228 }; 229 }; 230 231 regulators-1 { 232 compatible = "qcom,pm8350c-rpmh-regulators"; 233 qcom,pmic-id = "c"; 234 235 vdd-s1-supply = <&vph_pwr>; 236 vdd-s2-supply = <&vph_pwr>; 237 vdd-s3-supply = <&vph_pwr>; 238 vdd-s4-supply = <&vph_pwr>; 239 vdd-s5-supply = <&vph_pwr>; 240 vdd-s6-supply = <&vph_pwr>; 241 vdd-s7-supply = <&vph_pwr>; 242 vdd-s8-supply = <&vph_pwr>; 243 vdd-s9-supply = <&vph_pwr>; 244 vdd-s10-supply = <&vph_pwr>; 245 246 vdd-l1-l12-supply = <&vreg_s1c_1p86>; 247 vdd-l2-l8-supply = <&vreg_s1c_1p86>; 248 vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>; 249 vdd-l6-l9-l11-supply = <&vreg_bob>; 250 vdd-l10-supply = <&vreg_s12b_1p25>; 251 252 vdd-bob-supply = <&vph_pwr>; 253 254 vreg_s1c_1p86: smps1 { 255 regulator-name = "vreg_s1c_1p86"; 256 regulator-min-microvolt = <1856000>; 257 regulator-max-microvolt = <1880000>; 258 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 259 }; 260 261 vreg_bob: bob { 262 regulator-name = "vreg_bob"; 263 regulator-min-microvolt = <3008000>; 264 regulator-max-microvolt = <3960000>; 265 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; 266 }; 267 268 vreg_l1c_1p8: ldo1 { 269 regulator-name = "vreg_l1c_1p8"; 270 regulator-min-microvolt = <1800000>; 271 regulator-max-microvolt = <1800000>; 272 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 273 }; 274 275 vreg_l2c_1p8: ldo2 { 276 regulator-name = "vreg_l2c_1p8"; 277 regulator-min-microvolt = <1800000>; 278 regulator-max-microvolt = <1800000>; 279 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 280 }; 281 282 vreg_l6c_1p8: ldo6 { 283 regulator-name = "vreg_l6c_1p8"; 284 regulator-min-microvolt = <1800000>; 285 regulator-max-microvolt = <2960000>; 286 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 287 }; 288 289 vreg_l9c_2p96: ldo9 { 290 regulator-name = "vreg_l9c_2p96"; 291 regulator-min-microvolt = <2960000>; 292 regulator-max-microvolt = <3008000>; 293 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 294 }; 295 296 vreg_l10c_1p2: ldo10 { 297 regulator-name = "vreg_l10c_1p2"; 298 regulator-min-microvolt = <1200000>; 299 regulator-max-microvolt = <1200000>; 300 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 301 }; 302 }; 303 304 regulators-2 { 305 compatible = "qcom,pmr735a-rpmh-regulators"; 306 qcom,pmic-id = "e"; 307 308 vdd-s1-supply = <&vph_pwr>; 309 vdd-s2-supply = <&vph_pwr>; 310 vdd-s3-supply = <&vph_pwr>; 311 312 vdd-l1-l2-supply = <&vreg_s2e_0p85>; 313 vdd-l3-supply = <&vreg_s1e_1p25>; 314 vdd-l4-supply = <&vreg_s1c_1p86>; 315 vdd-l5-l6-supply = <&vreg_s1c_1p86>; 316 vdd-l7-bob-supply = <&vreg_bob>; 317 318 vreg_s1e_1p25: smps1 { 319 regulator-name = "vreg_s1e_1p25"; 320 regulator-min-microvolt = <1200000>; 321 regulator-max-microvolt = <1280000>; 322 }; 323 324 vreg_s2e_0p85: smps2 { 325 regulator-name = "vreg_s2e_0p85"; 326 regulator-min-microvolt = <950000>; 327 regulator-max-microvolt = <976000>; 328 }; 329 330 vreg_s3e_2p20: smps3 { 331 regulator-name = "vreg_s3e_2p20"; 332 regulator-min-microvolt = <2200000>; 333 regulator-max-microvolt = <2352000>; 334 }; 335 336 vreg_l1e_0p9: ldo1 { 337 regulator-name = "vreg_l1e_0p9"; 338 regulator-min-microvolt = <912000>; 339 regulator-max-microvolt = <912000>; 340 }; 341 342 vreg_l2e_1p2: ldo2 { 343 regulator-name = "vreg_l2e_0p8"; 344 regulator-min-microvolt = <1200000>; 345 regulator-max-microvolt = <1200000>; 346 }; 347 348 vreg_l3e_1p2: ldo3 { 349 regulator-name = "vreg_l3e_1p2"; 350 regulator-min-microvolt = <1200000>; 351 regulator-max-microvolt = <1200000>; 352 }; 353 354 vreg_l4e_1p7: ldo4 { 355 regulator-name = "vreg_l4e_1p7"; 356 regulator-min-microvolt = <1776000>; 357 regulator-max-microvolt = <1872000>; 358 }; 359 360 vreg_l5e_0p8: ldo5 { 361 regulator-name = "vreg_l5e_0p8"; 362 regulator-min-microvolt = <800000>; 363 regulator-max-microvolt = <800000>; 364 }; 365 366 vreg_l6e_0p8: ldo6 { 367 regulator-name = "vreg_l6e_0p8"; 368 regulator-min-microvolt = <480000>; 369 regulator-max-microvolt = <904000>; 370 }; 371 372 vreg_l7e_2p8: ldo7 { 373 regulator-name = "vreg_l7e_2p8"; 374 regulator-min-microvolt = <2800000>; 375 regulator-max-microvolt = <2800000>; 376 }; 377 }; 378}; 379 380&cdsp { 381 status = "okay"; 382 firmware-name = "qcom/sm8350/cdsp.mbn"; 383}; 384 385&dispcc { 386 status = "okay"; 387}; 388 389&mdss_dsi0 { 390 vdda-supply = <&vreg_l6b_1p2>; 391 status = "okay"; 392 393 ports { 394 port@1 { 395 endpoint { 396 remote-endpoint = <<9611_a>; 397 data-lanes = <0 1 2 3>; 398 }; 399 }; 400 }; 401}; 402 403&mdss_dsi0_phy { 404 vdds-supply = <&vreg_l5b_0p88>; 405 status = "okay"; 406}; 407 408&gpi_dma1 { 409 status = "okay"; 410}; 411 412&gpu { 413 status = "okay"; 414 415 zap-shader { 416 firmware-name = "qcom/sm8350/a660_zap.mbn"; 417 }; 418}; 419 420&i2c13 { 421 clock-frequency = <100000>; 422 423 status = "okay"; 424 425 typec-mux@42 { 426 compatible = "fcs,fsa4480"; 427 reg = <0x42>; 428 429 interrupts-extended = <&tlmm 2 IRQ_TYPE_LEVEL_LOW>; 430 431 vcc-supply = <&vreg_bob>; 432 mode-switch; 433 orientation-switch; 434 435 port { 436 fsa4480_sbu_mux: endpoint { 437 remote-endpoint = <&pmic_glink_sbu>; 438 }; 439 }; 440 }; 441}; 442 443&i2c15 { 444 clock-frequency = <400000>; 445 status = "okay"; 446 447 lt9611_codec: hdmi-bridge@2b { 448 compatible = "lontium,lt9611uxc"; 449 reg = <0x2b>; 450 451 interrupts-extended = <&tlmm 50 IRQ_TYPE_EDGE_FALLING>; 452 reset-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>; 453 454 vdd-supply = <<9611_1v2>; 455 vcc-supply = <<9611_3v3>; 456 457 pinctrl-names = "default"; 458 pinctrl-0 = <<9611_state>; 459 460 ports { 461 #address-cells = <1>; 462 #size-cells = <0>; 463 464 port@0 { 465 reg = <0>; 466 467 lt9611_a: endpoint { 468 remote-endpoint = <&mdss_dsi0_out>; 469 }; 470 }; 471 472 port@2 { 473 reg = <2>; 474 475 lt9611_out: endpoint { 476 remote-endpoint = <&hdmi_con>; 477 }; 478 }; 479 }; 480 }; 481}; 482 483&mdss { 484 status = "okay"; 485}; 486 487&mdss_dp { 488 status = "okay"; 489 490 ports { 491 port@1 { 492 reg = <1>; 493 494 mdss_dp0_out: endpoint { 495 data-lanes = <0 1>; 496 remote-endpoint = <&usb_1_qmpphy_dp_in>; 497 }; 498 }; 499 }; 500}; 501 502&mpss { 503 status = "okay"; 504 firmware-name = "qcom/sm8350/modem.mbn"; 505}; 506 507&pcie0 { 508 pinctrl-names = "default"; 509 pinctrl-0 = <&pcie0_default_state>; 510 511 perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>; 512 wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>; 513 514 status = "okay"; 515}; 516 517&pcie0_phy { 518 vdda-phy-supply = <&vreg_l5b_0p88>; 519 vdda-pll-supply = <&vreg_l6b_1p2>; 520 521 status = "okay"; 522}; 523 524&pcie1 { 525 perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>; 526 wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>; 527 528 pinctrl-names = "default"; 529 pinctrl-0 = <&pcie1_default_state>; 530 531 status = "okay"; 532}; 533 534&pcie1_phy { 535 status = "okay"; 536 vdda-phy-supply = <&vreg_l5b_0p88>; 537 vdda-pll-supply = <&vreg_l6b_1p2>; 538}; 539 540&qupv3_id_0 { 541 status = "okay"; 542}; 543 544&qupv3_id_1 { 545 status = "okay"; 546}; 547 548&qupv3_id_2 { 549 status = "okay"; 550}; 551 552&sdhc_2 { 553 cd-gpios = <&tlmm 92 GPIO_ACTIVE_HIGH>; 554 pinctrl-names = "default", "sleep"; 555 pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>; 556 pinctrl-1 = <&sdc2_sleep_state &sdc2_card_det_n>; 557 vmmc-supply = <&vreg_l9c_2p96>; 558 vqmmc-supply = <&vreg_l6c_1p8>; 559 no-sdio; 560 no-mmc; 561 status = "okay"; 562}; 563 564&slpi { 565 status = "okay"; 566 firmware-name = "qcom/sm8350/slpi.mbn"; 567}; 568 569&tlmm { 570 gpio-reserved-ranges = <52 8>; 571 572 gpio-line-names = 573 "APPS_I2C_SDA", /* GPIO_0 */ 574 "APPS_I2C_SCL", 575 "FSA_INT_N", 576 "USER_LED3_EN", 577 "SMBUS_SDA_1P8", 578 "SMBUS_SCL_1P8", 579 "2M2_3P3_EN", 580 "ALERT_DUAL_M2_N", 581 "EXP_UART_CTS", 582 "EXP_UART_RFR", 583 "EXP_UART_TX", /* GPIO_10 */ 584 "EXP_UART_RX", 585 "NC", 586 "NC", 587 "RCM_MARKER1", 588 "WSA0_EN", 589 "CAM1_RESET_N", 590 "CAM0_RESET_N", 591 "DEBUG_UART_TX", 592 "DEBUG_UART_RX", 593 "TS_I2C_SDA", /* GPIO_20 */ 594 "TS_I2C_SCL", 595 "TS_RESET_N", 596 "TS_INT_N", 597 "DISP0_RESET_N", 598 "DISP1_RESET_N", 599 "ETH_RESET", 600 "RCM_MARKER2", 601 "CAM_DC_MIPI_MUX_EN", 602 "CAM_DC_MIPI_MUX_SEL", 603 "AFC_PHY_TA_D_PLUS", /* GPIO_30 */ 604 "AFC_PHY_TA_D_MINUS", 605 "PM8008_1_IRQ", 606 "PM8008_1_RESET_N", 607 "PM8008_2_IRQ", 608 "PM8008_2_RESET_N", 609 "CAM_DC_I3C_SDA", 610 "CAM_DC_I3C_SCL", 611 "FP_INT_N", 612 "FP_WUHB_INT_N", 613 "SMB_SPMI_DATA", /* GPIO_40 */ 614 "SMB_SPMI_CLK", 615 "USB_HUB_RESET", 616 "FORCE_USB_BOOT", 617 "LRF_IRQ", 618 "NC", 619 "IMU2_INT", 620 "HDMI_3P3_EN", 621 "HDMI_RSTN", 622 "HDMI_1P2_EN", 623 "HDMI_INT", /* GPIO_50 */ 624 "USB1_ID", 625 "FP_SPI_MISO", 626 "FP_SPI_MOSI", 627 "FP_SPI_CLK", 628 "FP_SPI_CS_N", 629 "NFC_ESE_SPI_MISO", 630 "NFC_ESE_SPI_MOSI", 631 "NFC_ESE_SPI_CLK", 632 "NFC_ESE_SPI_CS", 633 "NFC_I2C_SDA", /* GPIO_60 */ 634 "NFC_I2C_SCLC", 635 "NFC_EN", 636 "NFC_CLK_REQ", 637 "HST_WLAN_EN", 638 "HST_BT_EN", 639 "HST_SW_CTRL", 640 "NC", 641 "HST_BT_UART_CTS", 642 "HST_BT_UART_RFR", 643 "HST_BT_UART_TX", /* GPIO_70 */ 644 "HST_BT_UART_RX", 645 "CAM_DC_SPI0_MISO", 646 "CAM_DC_SPI0_MOSI", 647 "CAM_DC_SPI0_CLK", 648 "CAM_DC_SPI0_CS_N", 649 "CAM_DC_SPI1_MISO", 650 "CAM_DC_SPI1_MOSI", 651 "CAM_DC_SPI1_CLK", 652 "CAM_DC_SPI1_CS_N", 653 "HALL_INT_N", /* GPIO_80 */ 654 "USB_PHY_PS", 655 "MDP_VSYNC_P", 656 "MDP_VSYNC_S", 657 "ETH_3P3_EN", 658 "RADAR_INT", 659 "NFC_DWL_REQ", 660 "SM_GPIO_87", 661 "WCD_RESET_N", 662 "ALSP_INT_N", 663 "PRESS_INT", /* GPIO_90 */ 664 "SAR_INT_N", 665 "SD_CARD_DET_N", 666 "NC", 667 "PCIE0_RESET_N", 668 "PCIE0_CLK_REQ_N", 669 "PCIE0_WAKE_N", 670 "PCIE1_RESET_N", 671 "PCIE1_CLK_REQ_N", 672 "PCIE1_WAKE_N", 673 "CAM_MCLK0", /* GPIO_100 */ 674 "CAM_MCLK1", 675 "CAM_MCLK2", 676 "CAM_MCLK3", 677 "CAM_MCLK4", 678 "CAM_MCLK5", 679 "CAM2_RESET_N", 680 "CCI_I2C0_SDA", 681 "CCI_I2C0_SCL", 682 "CCI_I2C1_SDA", 683 "CCI_I2C1_SCL", /* GPIO_110 */ 684 "CCI_I2C2_SDA", 685 "CCI_I2C2_SCL", 686 "CCI_I2C3_SDA", 687 "CCI_I2C3_SCL", 688 "CAM5_RESET_N", 689 "CAM4_RESET_N", 690 "CAM3_RESET_N", 691 "IMU1_INT", 692 "MAG_INT_N", 693 "MI2S2_I2S_SCK", /* GPIO_120 */ 694 "MI2S2_I2S_DAT0", 695 "MI2S2_I2S_WS", 696 "HIFI_DAC_I2S_MCLK", 697 "MI2S2_I2S_DAT1", 698 "HIFI_DAC_I2S_SCK", 699 "HIFI_DAC_I2S_DAT0", 700 "NC", 701 "HIFI_DAC_I2S_WS", 702 "HST_BT_WLAN_SLIMBUS_CLK", 703 "HST_BT_WLAN_SLIMBUS_DAT0", /* GPIO_130 */ 704 "BT_LED_EN", 705 "WLAN_LED_EN", 706 "NC", 707 "NC", 708 "NC", 709 "UIM2_PRESENT", 710 "NC", 711 "NC", 712 "NC", 713 "UIM1_PRESENT", /* GPIO_140 */ 714 "NC", 715 "SM_RFFE0_DATA", 716 "NC", 717 "SM_RFFE1_DATA", 718 "SM_MSS_GRFC4", 719 "SM_MSS_GRFC5", 720 "SM_MSS_GRFC6", 721 "SM_MSS_GRFC7", 722 "SM_RFFE4_CLK", 723 "SM_RFFE4_DATA", /* GPIO_150 */ 724 "WLAN_COEX_UART1_RX", 725 "WLAN_COEX_UART1_TX", 726 "HST_SW_CTRL", 727 "DSI0_STATUS", 728 "DSI1_STATUS", 729 "APPS_PBL_BOOT_SPEED_1", 730 "APPS_BOOT_FROM_ROM", 731 "APPS_PBL_BOOT_SPEED_0", 732 "QLINK0_REQ", 733 "QLINK0_EN", /* GPIO_160 */ 734 "QLINK0_WMSS_RESET_N", 735 "NC", 736 "NC", 737 "NC", 738 "NC", 739 "NC", 740 "NC", 741 "WCD_SWR_TX_CLK", 742 "WCD_SWR_TX_DATA0", 743 "WCD_SWR_TX_DATA1", /* GPIO_170 */ 744 "WCD_SWR_RX_CLK", 745 "WCD_SWR_RX_DATA0", 746 "WCD_SWR_RX_DATA1", 747 "DMIC01_CLK", 748 "DMIC01_DATA", 749 "DMIC23_CLK", 750 "DMIC23_DATA", 751 "WSA_SWR_CLK", 752 "WSA_SWR_DATA", 753 "DMIC45_CLK", /* GPIO_180 */ 754 "DMIC45_DATA", 755 "WCD_SWR_TX_DATA2", 756 "SENSOR_I3C_SDA", 757 "SENSOR_I3C_SCL", 758 "CAM_OIS0_I3C_SDA", 759 "CAM_OIS0_I3C_SCL", 760 "IMU_SPI_MISO", 761 "IMU_SPI_MOSI", 762 "IMU_SPI_CLK", 763 "IMU_SPI_CS_N", /* GPIO_190 */ 764 "MAG_I2C_SDA", 765 "MAG_I2C_SCL", 766 "SENSOR_I2C_SDA", 767 "SENSOR_I2C_SCL", 768 "RADAR_SPI_MISO", 769 "RADAR_SPI_MOSI", 770 "RADAR_SPI_CLK", 771 "RADAR_SPI_CS_N", 772 "HST_BLE_UART_TX", 773 "HST_BLE_UART_RX", /* GPIO_200 */ 774 "HST_WLAN_UART_TX", 775 "HST_WLAN_UART_RX"; 776 777 pcie0_default_state: pcie0-default-state { 778 perst-pins { 779 pins = "gpio94"; 780 function = "gpio"; 781 drive-strength = <2>; 782 bias-pull-down; 783 }; 784 785 clkreq-pins { 786 pins = "gpio95"; 787 function = "pcie0_clkreqn"; 788 drive-strength = <2>; 789 bias-pull-up; 790 }; 791 792 wake-pins { 793 pins = "gpio96"; 794 function = "gpio"; 795 drive-strength = <2>; 796 bias-pull-up; 797 }; 798 }; 799 800 pcie1_default_state: pcie1-default-state { 801 perst-pins { 802 pins = "gpio97"; 803 function = "gpio"; 804 drive-strength = <2>; 805 bias-pull-down; 806 }; 807 808 clkreq-pins { 809 pins = "gpio98"; 810 function = "pcie1_clkreqn"; 811 drive-strength = <2>; 812 bias-pull-up; 813 }; 814 815 wake-pins { 816 pins = "gpio99"; 817 function = "gpio"; 818 drive-strength = <2>; 819 bias-pull-up; 820 }; 821 }; 822 823 sdc2_card_det_n: sd-card-det-n-state { 824 pins = "gpio92"; 825 function = "gpio"; 826 drive-strength = <2>; 827 bias-pull-up; 828 }; 829}; 830 831&uart2 { 832 status = "okay"; 833}; 834 835&ufs_mem_hc { 836 status = "okay"; 837 838 reset-gpios = <&tlmm 203 GPIO_ACTIVE_LOW>; 839 840 vcc-supply = <&vreg_l7b_2p96>; 841 vcc-max-microamp = <800000>; 842 vccq-supply = <&vreg_l9b_1p2>; 843 vccq-max-microamp = <900000>; 844 vdd-hba-supply = <&vreg_l9b_1p2>; 845}; 846 847&ufs_mem_phy { 848 status = "okay"; 849 850 vdda-phy-supply = <&vreg_l5b_0p88>; 851 vdda-pll-supply = <&vreg_l6b_1p2>; 852}; 853 854&usb_1 { 855 status = "okay"; 856}; 857 858&usb_1_dwc3 { 859 dr_mode = "otg"; 860 usb-role-switch; 861}; 862 863&usb_1_dwc3_hs { 864 remote-endpoint = <&pmic_glink_hs_in>; 865}; 866 867&usb_1_dwc3_ss { 868 remote-endpoint = <&usb_1_qmpphy_usb_ss_in>; 869}; 870 871&usb_1_hsphy { 872 status = "okay"; 873 874 vdda-pll-supply = <&vreg_l5b_0p88>; 875 vdda18-supply = <&vreg_l1c_1p8>; 876 vdda33-supply = <&vreg_l2b_3p07>; 877}; 878 879&usb_1_qmpphy { 880 status = "okay"; 881 882 vdda-phy-supply = <&vreg_l6b_1p2>; 883 vdda-pll-supply = <&vreg_l1b_0p88>; 884 885 orientation-switch; 886}; 887 888&usb_1_qmpphy_dp_in { 889 remote-endpoint = <&mdss_dp0_out>; 890}; 891 892&usb_1_qmpphy_out { 893 remote-endpoint = <&pmic_glink_ss_in>; 894}; 895 896&usb_1_qmpphy_usb_ss_in { 897 remote-endpoint = <&usb_1_dwc3_ss>; 898}; 899 900&usb_2 { 901 status = "okay"; 902}; 903 904&usb_2_dwc3 { 905 dr_mode = "host"; 906 907 pinctrl-names = "default"; 908 pinctrl-0 = <&usb_hub_enabled_state>; 909}; 910 911&usb_2_hsphy { 912 status = "okay"; 913 914 vdda-pll-supply = <&vreg_l5b_0p88>; 915 vdda18-supply = <&vreg_l1c_1p8>; 916 vdda33-supply = <&vreg_l2b_3p07>; 917}; 918 919&usb_2_qmpphy { 920 status = "okay"; 921 922 vdda-phy-supply = <&vreg_l6b_1p2>; 923 vdda-pll-supply = <&vreg_l5b_0p88>; 924}; 925 926/* PINCTRL - additions to nodes defined in sm8350.dtsi */ 927 928&tlmm { 929 usb_hub_enabled_state: usb-hub-enabled-state { 930 pins = "gpio42"; 931 function = "gpio"; 932 933 drive-strength = <2>; 934 output-low; 935 }; 936 937 lt9611_state: lt9611-state { 938 rst-pins { 939 pins = "gpio48"; 940 function = "gpio"; 941 942 output-high; 943 input-disable; 944 }; 945 946 irq-pins { 947 pins = "gpio50"; 948 function = "gpio"; 949 bias-disable; 950 }; 951 }; 952}; 953