1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2022-2024 Jianhua Lu <lujianhua000@gmail.com> 4 */ 5 6#include <dt-bindings/arm/qcom,ids.h> 7#include <dt-bindings/phy/phy.h> 8#include <dt-bindings/regulator/qcom,rpmh-regulator.h> 9#include <dt-bindings/usb/pd.h> 10#include "sm8250.dtsi" 11#include "pm8150.dtsi" 12#include "pm8150b.dtsi" 13#include "pm8150l.dtsi" 14#include "pm8009.dtsi" 15 16/* 17 * Delete following upstream (sm8250.dtsi) reserved 18 * memory mappings which are different on this device. 19 */ 20/delete-node/ &adsp_mem; 21/delete-node/ &cdsp_secure_heap; 22/delete-node/ &slpi_mem; 23/delete-node/ &spss_mem; 24/delete-node/ &xbl_aop_mem; 25 26/ { 27 chassis-type = "tablet"; 28 29 /* required for bootloader to select correct board */ 30 qcom,msm-id = <QCOM_ID_SM8250 0x20001>; /* SM8250 v2.1 */ 31 qcom,board-id = <0x10008 0>; 32 33 chosen { 34 #address-cells = <2>; 35 #size-cells = <2>; 36 ranges; 37 38 framebuffer: framebuffer@9c000000 { 39 compatible = "simple-framebuffer"; 40 reg = <0x0 0x9c000000 0x0 0x2300000>; 41 width = <1600>; 42 height = <2560>; 43 stride = <(1600 * 4)>; 44 format = "a8r8g8b8"; 45 }; 46 }; 47 48 battery_l: battery-l { 49 compatible = "simple-battery"; 50 voltage-min-design-microvolt = <3870000>; 51 energy-full-design-microwatt-hours = <16600000>; 52 charge-full-design-microamp-hours = <4300000>; 53 }; 54 55 battery_r: battery-r { 56 compatible = "simple-battery"; 57 voltage-min-design-microvolt = <3870000>; 58 energy-full-design-microwatt-hours = <16600000>; 59 charge-full-design-microamp-hours = <4300000>; 60 }; 61 62 bl_vddpos_5p5: bl-vddpos-regulator { 63 compatible = "regulator-fixed"; 64 regulator-name = "bl_vddpos_5p5"; 65 regulator-min-microvolt = <5500000>; 66 regulator-max-microvolt = <5500000>; 67 regulator-enable-ramp-delay = <233>; 68 gpio = <&tlmm 130 GPIO_ACTIVE_HIGH>; 69 enable-active-high; 70 regulator-boot-on; 71 }; 72 73 bl_vddneg_5p5: bl-vddneg-regulator { 74 compatible = "regulator-fixed"; 75 regulator-name = "bl_vddneg_5p5"; 76 regulator-min-microvolt = <5500000>; 77 regulator-max-microvolt = <5500000>; 78 regulator-enable-ramp-delay = <233>; 79 gpio = <&tlmm 131 GPIO_ACTIVE_HIGH>; 80 enable-active-high; 81 regulator-boot-on; 82 }; 83 84 gpio_keys: gpio-keys { 85 compatible = "gpio-keys"; 86 87 pinctrl-names = "default"; 88 pinctrl-0 = <&vol_up_n>; 89 90 key-vol-up { 91 label = "Volume Up"; 92 gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>; 93 linux,code = <KEY_VOLUMEUP>; 94 debounce-interval = <15>; 95 linux,can-disable; 96 wakeup-source; 97 }; 98 }; 99 100 vph_pwr: vph-pwr-regulator { 101 compatible = "regulator-fixed"; 102 regulator-name = "vph_pwr"; 103 regulator-min-microvolt = <3700000>; 104 regulator-max-microvolt = <3700000>; 105 }; 106 107 /* S6c is really ebi.lvl but it's there for supply map completeness sake. */ 108 vreg_s6c_0p88: smpc6-regulator { 109 compatible = "regulator-fixed"; 110 regulator-name = "vreg_s6c_0p88"; 111 regulator-min-microvolt = <880000>; 112 regulator-max-microvolt = <880000>; 113 regulator-always-on; 114 vin-supply = <&vph_pwr>; 115 }; 116 117 reserved-memory { 118 xbl_aop_mem: xbl-aop@80600000 { 119 reg = <0x0 0x80600000 0x0 0x260000>; 120 no-map; 121 }; 122 123 slpi_mem: slpi@88c00000 { 124 reg = <0x0 0x88c00000 0x0 0x2f00000>; 125 no-map; 126 }; 127 128 adsp_mem: adsp@8bb00000 { 129 reg = <0x0 0x8bb00000 0x0 0x2500000>; 130 no-map; 131 }; 132 133 spss_mem: spss@8e000000 { 134 reg = <0x0 0x8e000000 0x0 0x100000>; 135 no-map; 136 }; 137 138 cdsp_secure_heap: cdsp-secure-heap@8e100000 { 139 reg = <0x0 0x8e100000 0x0 0x4600000>; 140 no-map; 141 }; 142 143 cont_splash_mem: cont-splash@9c000000 { 144 reg = <0x0 0x9c000000 0x0 0x2300000>; 145 no-map; 146 }; 147 148 ramoops@b0000000 { 149 compatible = "ramoops"; 150 reg = <0x0 0xb0000000 0x0 0x400000>; 151 record-size = <0x1000>; 152 console-size = <0x200000>; 153 ecc-size = <16>; 154 no-map; 155 }; 156 }; 157}; 158 159&adsp { 160 firmware-name = "qcom/sm8250/xiaomi/elish/adsp.mbn"; 161 status = "okay"; 162}; 163 164&apps_rsc { 165 regulators-0 { 166 compatible = "qcom,pm8150-rpmh-regulators"; 167 qcom,pmic-id = "a"; 168 169 vdd-s1-supply = <&vph_pwr>; 170 vdd-s2-supply = <&vph_pwr>; 171 vdd-s3-supply = <&vph_pwr>; 172 vdd-s4-supply = <&vph_pwr>; 173 vdd-s5-supply = <&vph_pwr>; 174 vdd-s6-supply = <&vph_pwr>; 175 vdd-s7-supply = <&vph_pwr>; 176 vdd-s8-supply = <&vph_pwr>; 177 vdd-s9-supply = <&vph_pwr>; 178 vdd-s10-supply = <&vph_pwr>; 179 vdd-l1-l8-l11-supply = <&vreg_s6c_0p88>; 180 vdd-l2-l10-supply = <&vreg_bob>; 181 vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p95>; 182 vdd-l6-l9-supply = <&vreg_s8c_1p35>; 183 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>; 184 vdd-l13-l16-l17-supply = <&vreg_bob>; 185 186 /* (S1+S2+S3) - cx.lvl (ARC) */ 187 188 vreg_s4a_1p8: smps4 { 189 regulator-name = "vreg_s4a_1p8"; 190 regulator-min-microvolt = <1800000>; 191 regulator-max-microvolt = <1920000>; 192 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 193 regulator-allow-set-load; 194 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 195 RPMH_REGULATOR_MODE_HPM>; 196 }; 197 198 vreg_s5a_1p9: smps5 { 199 regulator-name = "vreg_s5a_1p9"; 200 regulator-min-microvolt = <1900000>; 201 regulator-max-microvolt = <2040000>; 202 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 203 }; 204 205 vreg_s6a_0p95: smps6 { 206 regulator-name = "vreg_s6a_0p95"; 207 regulator-min-microvolt = <950000>; 208 regulator-max-microvolt = <1128000>; 209 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 210 }; 211 212 vreg_l2a_3p1: ldo2 { 213 regulator-name = "vreg_l2a_3p1"; 214 regulator-min-microvolt = <3072000>; 215 regulator-max-microvolt = <3072000>; 216 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 217 }; 218 219 vreg_l3a_0p9: ldo3 { 220 regulator-name = "vreg_l3a_0p9"; 221 regulator-min-microvolt = <928000>; 222 regulator-max-microvolt = <932000>; 223 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 224 }; 225 226 /* L4 - lmx.lvl (ARC) */ 227 228 vreg_l5a_0p88: ldo5 { 229 regulator-name = "vreg_l5a_0p88"; 230 regulator-min-microvolt = <880000>; 231 regulator-max-microvolt = <880000>; 232 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 233 }; 234 235 vreg_l6a_1p2: ldo6 { 236 regulator-name = "vreg_l6a_1p2"; 237 regulator-min-microvolt = <1200000>; 238 regulator-max-microvolt = <1200000>; 239 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 240 regulator-allow-set-load; 241 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 242 RPMH_REGULATOR_MODE_HPM>; 243 }; 244 245 /* L7 is unused. */ 246 247 vreg_l9a_1p2: ldo9 { 248 regulator-name = "vreg_l9a_1p2"; 249 regulator-min-microvolt = <1200000>; 250 regulator-max-microvolt = <1200000>; 251 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 252 }; 253 254 /* L10 is unused, L11 - lcx.lvl (ARC) */ 255 256 vreg_l12a_1p8: ldo12 { 257 regulator-name = "vreg_l12a_1p8"; 258 regulator-min-microvolt = <1800000>; 259 regulator-max-microvolt = <1800000>; 260 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 261 }; 262 263 /* L13 is unused. */ 264 265 vreg_l14a_1p88: ldo14 { 266 regulator-name = "vreg_l14a_1p88"; 267 regulator-min-microvolt = <1880000>; 268 regulator-max-microvolt = <1880000>; 269 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 270 }; 271 272 /* L15 & L16 are unused. */ 273 274 vreg_l17a_3p0: ldo17 { 275 regulator-name = "vreg_l17a_3p0"; 276 regulator-min-microvolt = <2496000>; 277 regulator-max-microvolt = <3008000>; 278 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 279 regulator-allow-set-load; 280 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 281 RPMH_REGULATOR_MODE_HPM>; 282 }; 283 284 vreg_l18a_0p9: ldo18 { 285 regulator-name = "vreg_l18a_0p9"; 286 regulator-min-microvolt = <800000>; 287 regulator-max-microvolt = <920000>; 288 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 289 }; 290 }; 291 292 /* 293 * Remaining regulators that are not yet supported: 294 * OLEDB: 4925000-8100000 295 * ab: 4600000-6100000 296 * ibb: 800000-5400000 297 */ 298 regulators-1 { 299 compatible = "qcom,pm8150l-rpmh-regulators"; 300 qcom,pmic-id = "c"; 301 302 vdd-s1-supply = <&vph_pwr>; 303 vdd-s2-supply = <&vph_pwr>; 304 vdd-s3-supply = <&vph_pwr>; 305 vdd-s4-supply = <&vph_pwr>; 306 vdd-s5-supply = <&vph_pwr>; 307 vdd-s6-supply = <&vph_pwr>; 308 vdd-s7-supply = <&vph_pwr>; 309 vdd-s8-supply = <&vph_pwr>; 310 vdd-l1-l8-supply = <&vreg_s4a_1p8>; 311 vdd-l2-l3-supply = <&vreg_s8c_1p35>; 312 vdd-l4-l5-l6-supply = <&vreg_bob>; 313 vdd-l7-l11-supply = <&vreg_bob>; 314 vdd-l9-l10-supply = <&vreg_bob>; 315 vdd-bob-supply = <&vph_pwr>; 316 317 vreg_bob: bob { 318 regulator-name = "vreg_bob"; 319 regulator-min-microvolt = <3350000>; 320 regulator-max-microvolt = <3960000>; 321 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; 322 }; 323 324 /* 325 * S1-S6 are ARCs: 326 * (S1+S2) - gfx.lvl, 327 * S3 - mx.lvl, 328 * (S4+S5) - mmcx.lvl, 329 * S6 - ebi.lvl 330 */ 331 332 vreg_s7c_0p35: smps7 { 333 regulator-name = "vreg_s7c_0p35"; 334 regulator-min-microvolt = <348000>; 335 regulator-max-microvolt = <1000000>; 336 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 337 }; 338 339 vreg_s8c_1p35: smps8 { 340 regulator-name = "vreg_s8c_1p35"; 341 regulator-min-microvolt = <1350000>; 342 regulator-max-microvolt = <1400000>; 343 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 344 }; 345 346 vreg_l1c_1p8: ldo1 { 347 regulator-name = "vreg_l1c_1p8"; 348 regulator-min-microvolt = <1800000>; 349 regulator-max-microvolt = <1800000>; 350 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 351 }; 352 353 /* L2-4 are unused. */ 354 355 vreg_l5c_1p8: ldo5 { 356 regulator-name = "vreg_l5c_1p8"; 357 regulator-min-microvolt = <1800000>; 358 regulator-max-microvolt = <2800000>; 359 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 360 }; 361 362 vreg_l6c_2p9: ldo6 { 363 regulator-name = "vreg_l6c_2p9"; 364 regulator-min-microvolt = <1800000>; 365 regulator-max-microvolt = <2960000>; 366 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 367 regulator-allow-set-load; 368 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 369 RPMH_REGULATOR_MODE_HPM>; 370 }; 371 372 vreg_l7c_2p85: ldo7 { 373 regulator-name = "vreg_l7c_2p85"; 374 regulator-min-microvolt = <2856000>; 375 regulator-max-microvolt = <3104000>; 376 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 377 }; 378 379 vreg_l8c_1p8: ldo8 { 380 regulator-name = "vreg_l8c_1p8"; 381 regulator-min-microvolt = <1800000>; 382 regulator-max-microvolt = <1800000>; 383 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 384 }; 385 386 vreg_l9c_2p9: ldo9 { 387 regulator-name = "vreg_l9c_2p9"; 388 regulator-min-microvolt = <2704000>; 389 regulator-max-microvolt = <2960000>; 390 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 391 regulator-allow-set-load; 392 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 393 RPMH_REGULATOR_MODE_HPM>; 394 }; 395 396 vreg_l10c_3p3: ldo10 { 397 regulator-name = "vreg_l10c_3p3"; 398 regulator-min-microvolt = <3296000>; 399 regulator-max-microvolt = <3296000>; 400 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 401 }; 402 403 vreg_l11c_3p0: ldo11 { 404 regulator-name = "vreg_l11c_3p0"; 405 regulator-min-microvolt = <3000000>; 406 regulator-max-microvolt = <3000000>; 407 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 408 }; 409 }; 410 411 regulators-2 { 412 compatible = "qcom,pm8009-rpmh-regulators"; 413 qcom,pmic-id = "f"; 414 415 vdd-s1-supply = <&vph_pwr>; 416 vdd-s2-supply = <&vreg_bob>; 417 vdd-l2-supply = <&vreg_s8c_1p35>; 418 vdd-l5-l6-supply = <&vreg_bob>; 419 vdd-l7-supply = <&vreg_s4a_1p8>; 420 421 vreg_s1f_1p2: smps1 { 422 regulator-name = "vreg_s1f_1p2"; 423 regulator-min-microvolt = <1200000>; 424 regulator-max-microvolt = <1200000>; 425 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 426 }; 427 428 vreg_s2f_0p5: smps2 { 429 regulator-name = "vreg_s2f_0p5"; 430 regulator-min-microvolt = <512000>; 431 regulator-max-microvolt = <1100000>; 432 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 433 }; 434 435 /* L1 is unused. */ 436 437 vreg_l2f_1p3: ldo2 { 438 regulator-name = "vreg_l2f_1p3"; 439 regulator-min-microvolt = <1304000>; 440 regulator-max-microvolt = <1304000>; 441 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 442 }; 443 444 /* L3 & L4 are unused. */ 445 446 vreg_l5f_2p8: ldo5 { 447 regulator-name = "vreg_l5f_2p85"; 448 regulator-min-microvolt = <2800000>; 449 regulator-max-microvolt = <2800000>; 450 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 451 }; 452 453 vreg_l6f_2p8: ldo6 { 454 regulator-name = "vreg_l6f_2p8"; 455 regulator-min-microvolt = <2800000>; 456 regulator-max-microvolt = <2800000>; 457 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 458 }; 459 460 vreg_l7f_1p8: ldo7 { 461 regulator-name = "vreg_l7f_1p8"; 462 regulator-min-microvolt = <1800000>; 463 regulator-max-microvolt = <1800000>; 464 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 465 }; 466 }; 467}; 468 469&cdsp { 470 firmware-name = "qcom/sm8250/xiaomi/elish/cdsp.mbn"; 471 status = "okay"; 472}; 473 474&gmu { 475 status = "okay"; 476}; 477 478&gpi_dma0 { 479 status = "okay"; 480}; 481 482&gpi_dma1 { 483 status = "okay"; 484}; 485 486&gpi_dma2 { 487 status = "okay"; 488}; 489 490&gpu { 491 status = "okay"; 492 493 zap-shader { 494 memory-region = <&gpu_mem>; 495 firmware-name = "qcom/sm8250/xiaomi/elish/a650_zap.mbn"; 496 }; 497}; 498 499&i2c0 { 500 clock-frequency = <400000>; 501 status = "okay"; 502 503 fuel-gauge@55 { 504 compatible = "ti,bq27z561"; 505 reg = <0x55>; 506 monitored-battery = <&battery_r>; 507 }; 508}; 509 510&i2c11 { 511 clock-frequency = <400000>; 512 status = "okay"; 513 514 backlight: backlight@11 { 515 compatible = "kinetic,ktz8866"; 516 reg = <0x11>; 517 vddpos-supply = <&bl_vddpos_5p5>; 518 vddneg-supply = <&bl_vddneg_5p5>; 519 enable-gpios = <&tlmm 139 GPIO_ACTIVE_HIGH>; 520 current-num-sinks = <5>; 521 kinetic,current-ramp-delay-ms = <128>; 522 kinetic,led-enable-ramp-delay-ms = <1>; 523 kinetic,enable-lcd-bias; 524 }; 525}; 526 527&i2c13 { 528 clock-frequency = <400000>; 529 status = "okay"; 530 531 fuel-gauge@55 { 532 compatible = "ti,bq27z561"; 533 reg = <0x55>; 534 monitored-battery = <&battery_l>; 535 }; 536}; 537 538&mdss { 539 status = "okay"; 540}; 541 542&mdss_dsi0 { 543 vdda-supply = <&vreg_l9a_1p2>; 544 qcom,dual-dsi-mode; 545 qcom,sync-dual-dsi; 546 qcom,master-dsi; 547 status = "okay"; 548 549 display_panel: panel@0 { 550 reg = <0>; 551 vddio-supply = <&vreg_l14a_1p88>; 552 reset-gpios = <&tlmm 75 GPIO_ACTIVE_LOW>; 553 backlight = <&backlight>; 554 rotation = <90>; 555 556 status = "disabled"; 557 558 ports { 559 #address-cells = <1>; 560 #size-cells = <0>; 561 562 port@0 { 563 reg = <0>; 564 565 panel_in_0: endpoint { 566 remote-endpoint = <&mdss_dsi0_out>; 567 }; 568 }; 569 570 port@1 { 571 reg = <1>; 572 573 panel_in_1: endpoint { 574 remote-endpoint = <&mdss_dsi1_out>; 575 }; 576 }; 577 }; 578 }; 579}; 580 581&mdss_dsi0_out { 582 data-lanes = <0 1 2>; 583 remote-endpoint = <&panel_in_0>; 584}; 585 586&mdss_dsi0_phy { 587 vdds-supply = <&vreg_l5a_0p88>; 588 phy-type = <PHY_TYPE_CPHY>; 589 status = "okay"; 590}; 591 592&mdss_dsi1 { 593 vdda-supply = <&vreg_l9a_1p2>; 594 qcom,dual-dsi-mode; 595 qcom,sync-dual-dsi; 596 /* DSI1 is slave, so use DSI0 clocks */ 597 assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>; 598 status = "okay"; 599}; 600 601&mdss_dsi1_out { 602 data-lanes = <0 1 2>; 603 remote-endpoint = <&panel_in_1>; 604}; 605 606&mdss_dsi1_phy { 607 vdds-supply = <&vreg_l5a_0p88>; 608 phy-type = <PHY_TYPE_CPHY>; 609 status = "okay"; 610}; 611 612&pcie0 { 613 status = "okay"; 614}; 615 616&pcie0_phy { 617 vdda-phy-supply = <&vreg_l5a_0p88>; 618 vdda-pll-supply = <&vreg_l9a_1p2>; 619 status = "okay"; 620}; 621 622&pm8150_gpios { 623 vol_up_n: vol-up-n-state { 624 pins = "gpio6"; 625 function = "normal"; 626 power-source = <1>; 627 input-enable; 628 bias-pull-up; 629 }; 630}; 631 632&pm8150b_typec { 633 vdd-pdphy-supply = <&vreg_l2a_3p1>; 634 status = "okay"; 635 636 connector { 637 compatible = "usb-c-connector"; 638 639 op-sink-microwatt = <10000000>; 640 power-role = "dual"; 641 data-role = "dual"; 642 self-powered; 643 644 source-pdos = <PDO_FIXED(5000, 3000, 645 PDO_FIXED_DUAL_ROLE | 646 PDO_FIXED_USB_COMM | 647 PDO_FIXED_DATA_SWAP)>; 648 649 sink-pdos = <PDO_FIXED(5000, 3000, 650 PDO_FIXED_DUAL_ROLE | 651 PDO_FIXED_USB_COMM | 652 PDO_FIXED_DATA_SWAP) 653 PDO_VAR(5000, 12000, 5000)>; 654 655 ports { 656 #address-cells = <1>; 657 #size-cells = <0>; 658 659 port@0 { 660 reg = <0>; 661 662 pm8150b_role_switch_in: endpoint { 663 remote-endpoint = <&usb_1_role_switch_out>; 664 }; 665 }; 666 }; 667 }; 668}; 669 670&pm8150b_vbus { 671 regulator-min-microamp = <500000>; 672 regulator-max-microamp = <3000000>; 673 status = "okay"; 674}; 675 676&pon_pwrkey { 677 status = "okay"; 678}; 679 680&pon_resin { 681 linux,code = <KEY_VOLUMEDOWN>; 682 status = "okay"; 683}; 684 685&qupv3_id_0 { 686 status = "okay"; 687}; 688 689&qupv3_id_1 { 690 status = "okay"; 691}; 692 693&qupv3_id_2 { 694 status = "okay"; 695}; 696 697&slpi { 698 firmware-name = "qcom/sm8250/xiaomi/elish/slpi.mbn"; 699 status = "okay"; 700}; 701 702&tlmm { 703 gpio-reserved-ranges = <40 4>; 704}; 705 706&usb_1 { 707 /* USB 2.0 only */ 708 qcom,select-utmi-as-pipe-clk; 709 status = "okay"; 710}; 711 712&usb_1_dwc3 { 713 dr_mode = "otg"; 714 maximum-speed = "high-speed"; 715 /* Remove USB3 phy */ 716 phys = <&usb_1_hsphy>; 717 phy-names = "usb2-phy"; 718 usb-role-switch; 719}; 720 721&usb_1_hsphy { 722 vdda-pll-supply = <&vreg_l5a_0p88>; 723 vdda18-supply = <&vreg_l12a_1p8>; 724 vdda33-supply = <&vreg_l2a_3p1>; 725 status = "okay"; 726}; 727 728&usb_1_role_switch_out { 729 remote-endpoint = <&pm8150b_role_switch_in>; 730}; 731 732&ufs_mem_hc { 733 vcc-supply = <&vreg_l17a_3p0>; 734 vcc-max-microamp = <800000>; 735 vccq-supply = <&vreg_l6a_1p2>; 736 vccq-max-microamp = <800000>; 737 vccq2-supply = <&vreg_s4a_1p8>; 738 vccq2-max-microamp = <800000>; 739 status = "okay"; 740}; 741 742&ufs_mem_phy { 743 vdda-phy-supply = <&vreg_l5a_0p88>; 744 vdda-pll-supply = <&vreg_l9a_1p2>; 745 status = "okay"; 746}; 747 748&venus { 749 firmware-name = "qcom/sm8250/xiaomi/elish/venus.mbn"; 750 status = "okay"; 751}; 752