1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> 4 */ 5 6#include <dt-bindings/regulator/qcom,rpmh-regulator.h> 7#include "sm8250.dtsi" 8#include "pm8150.dtsi" 9#include "pm8150b.dtsi" 10#include "pm8150l.dtsi" 11#include "pm8009.dtsi" 12 13/delete-node/ &adsp_mem; 14/delete-node/ &spss_mem; 15/delete-node/ &cdsp_secure_heap; 16 17/ { 18 qcom,msm-id = <356 0x20001>; /* SM8250 v2.1 */ 19 qcom,board-id = <0x10008 0>; 20 21 chosen { 22 #address-cells = <2>; 23 #size-cells = <2>; 24 ranges; 25 26 framebuffer: framebuffer@9c000000 { 27 compatible = "simple-framebuffer"; 28 reg = <0 0x9c000000 0 0x2300000>; 29 /* pdx203 BL initializes in 2.5k mode, not 4k */ 30 width = <1096>; 31 height = <2560>; 32 stride = <(1096 * 4)>; 33 format = "a8r8g8b8"; 34 /* 35 * That's a lot of clocks, but it's necessary due 36 * to unused clk cleanup & no panel driver yet.. 37 */ 38 clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, 39 <&gcc GCC_DISP_HF_AXI_CLK>, 40 <&gcc GCC_DISP_SF_AXI_CLK>, 41 <&dispcc DISP_CC_MDSS_VSYNC_CLK>, 42 <&dispcc DISP_CC_MDSS_MDP_CLK>, 43 <&dispcc DISP_CC_MDSS_BYTE0_CLK>, 44 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, 45 <&dispcc DISP_CC_MDSS_PCLK0_CLK>, 46 <&dispcc DISP_CC_MDSS_ESC0_CLK>; 47 power-domains = <&dispcc MDSS_GDSC>; 48 }; 49 }; 50 51 gpio_keys: gpio-keys { 52 compatible = "gpio-keys"; 53 54 pinctrl-0 = <&focus_n &snapshot_n &vol_down_n>; 55 pinctrl-names = "default"; 56 57 key-camera-focus { 58 label = "Camera Focus"; 59 linux,code = <KEY_CAMERA_FOCUS>; 60 gpios = <&pm8150b_gpios 2 GPIO_ACTIVE_LOW>; 61 debounce-interval = <15>; 62 linux,can-disable; 63 wakeup-source; 64 }; 65 66 key-camera-snapshot { 67 label = "Camera Snapshot"; 68 linux,code = <KEY_CAMERA>; 69 gpios = <&pm8150b_gpios 1 GPIO_ACTIVE_LOW>; 70 debounce-interval = <15>; 71 linux,can-disable; 72 wakeup-source; 73 }; 74 75 key-vol-down { 76 label = "Volume Down"; 77 linux,code = <KEY_VOLUMEDOWN>; 78 gpios = <&pm8150_gpios 1 GPIO_ACTIVE_LOW>; 79 debounce-interval = <15>; 80 linux,can-disable; 81 wakeup-source; 82 }; 83 }; 84 85 vph_pwr: vph-pwr-regulator { 86 compatible = "regulator-fixed"; 87 regulator-name = "vph_pwr"; 88 regulator-min-microvolt = <3700000>; 89 regulator-max-microvolt = <3700000>; 90 }; 91 92 /* S6c is really ebi.lvl but it's there for supply map completeness sake. */ 93 vreg_s6c_0p88: smpc6-regulator { 94 compatible = "regulator-fixed"; 95 regulator-name = "vreg_s6c_0p88"; 96 97 regulator-min-microvolt = <880000>; 98 regulator-max-microvolt = <880000>; 99 regulator-always-on; 100 vin-supply = <&vph_pwr>; 101 }; 102 103 reserved-memory { 104 adsp_mem: memory@8a100000 { 105 reg = <0x0 0x8a100000 0x0 0x2500000>; 106 no-map; 107 }; 108 109 spss_mem: memory@8c600000 { 110 reg = <0x0 0x8c600000 0x0 0x100000>; 111 no-map; 112 }; 113 114 cdsp_secure_heap: memory@8c700000 { 115 reg = <0x0 0x8c700000 0x0 0x4600000>; 116 no-map; 117 }; 118 119 cont_splash_mem: memory@9c000000 { 120 reg = <0x0 0x9c000000 0x0 0x2300000>; 121 no-map; 122 }; 123 124 ramoops@ffc00000 { 125 compatible = "ramoops"; 126 reg = <0x0 0xffc00000 0x0 0x100000>; 127 record-size = <0x1000>; 128 console-size = <0x40000>; 129 pmsg-size = <0x20000>; 130 ecc-size = <16>; 131 no-map; 132 }; 133 }; 134}; 135 136&adsp { 137 status = "okay"; 138}; 139 140&apps_rsc { 141 regulators-0 { 142 compatible = "qcom,pm8150-rpmh-regulators"; 143 qcom,pmic-id = "a"; 144 145 vdd-s1-supply = <&vph_pwr>; 146 vdd-s2-supply = <&vph_pwr>; 147 vdd-s3-supply = <&vph_pwr>; 148 vdd-s4-supply = <&vph_pwr>; 149 vdd-s5-supply = <&vph_pwr>; 150 vdd-s6-supply = <&vph_pwr>; 151 vdd-s7-supply = <&vph_pwr>; 152 vdd-s8-supply = <&vph_pwr>; 153 vdd-s9-supply = <&vph_pwr>; 154 vdd-s10-supply = <&vph_pwr>; 155 vdd-l1-l8-l11-supply = <&vreg_s6c_0p88>; 156 vdd-l2-l10-supply = <&vreg_bob>; 157 vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p6>; 158 vdd-l6-l9-supply = <&vreg_s8c_1p2>; 159 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>; 160 vdd-l13-l16-l17-supply = <&vreg_bob>; 161 162 /* (S1+S2+S3) - cx.lvl (ARC) */ 163 164 vreg_s4a_1p8: smps4 { 165 regulator-name = "vreg_s4a_1p8"; 166 regulator-min-microvolt = <1800000>; 167 regulator-max-microvolt = <1920000>; 168 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 169 }; 170 171 vreg_s5a_1p9: smps5 { 172 regulator-name = "vreg_s5a_1p9"; 173 regulator-min-microvolt = <1824000>; 174 regulator-max-microvolt = <2040000>; 175 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 176 }; 177 178 vreg_s6a_0p6: smps6 { 179 regulator-name = "vreg_s6a_0p6"; 180 regulator-min-microvolt = <600000>; 181 regulator-max-microvolt = <1128000>; 182 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 183 }; 184 185 vreg_l2a_3p1: ldo2 { 186 regulator-name = "vreg_l2a_3p1"; 187 regulator-min-microvolt = <3072000>; 188 regulator-max-microvolt = <3072000>; 189 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 190 }; 191 192 vreg_l3a_0p9: ldo3 { 193 regulator-name = "vreg_l3a_0p9"; 194 regulator-min-microvolt = <928000>; 195 regulator-max-microvolt = <932000>; 196 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 197 }; 198 199 /* L4 - lmx.lvl (ARC) */ 200 201 vreg_l5a_0p88: ldo5 { 202 regulator-name = "vreg_l5a_0p88"; 203 regulator-min-microvolt = <880000>; 204 regulator-max-microvolt = <880000>; 205 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 206 }; 207 208 vreg_l6a_1p2: ldo6 { 209 regulator-name = "vreg_l6a_1p2"; 210 regulator-min-microvolt = <1200000>; 211 regulator-max-microvolt = <1200000>; 212 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 213 }; 214 215 /* L7 is unused. */ 216 217 vreg_l9a_1p2: ldo9 { 218 regulator-name = "vreg_l9a_1p2"; 219 regulator-min-microvolt = <1200000>; 220 regulator-max-microvolt = <1200000>; 221 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 222 }; 223 224 /* L10 is unused, L11 - lcx.lvl (ARC) */ 225 226 vreg_l12a_1p8: ldo12 { 227 regulator-name = "vreg_l12a_1p8"; 228 regulator-min-microvolt = <1800000>; 229 regulator-max-microvolt = <1800000>; 230 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 231 }; 232 233 /* L13 is unused. */ 234 235 vreg_l14a_1p8: ldo14 { 236 regulator-name = "vreg_l14a_1p8"; 237 regulator-min-microvolt = <1800000>; 238 regulator-max-microvolt = <1880000>; 239 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 240 }; 241 242 /* L15 & L16 are unused. */ 243 244 vreg_l17a_3p0: ldo17 { 245 regulator-name = "vreg_l17a_3p0"; 246 regulator-min-microvolt = <2496000>; 247 regulator-max-microvolt = <3008000>; 248 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 249 }; 250 251 vreg_l18a_0p9: ldo18 { 252 regulator-name = "vreg_l18a_0p9"; 253 regulator-min-microvolt = <800000>; 254 regulator-max-microvolt = <920000>; 255 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 256 }; 257 }; 258 259 /* 260 * Remaining regulators that are not yet supported: 261 * OLEDB: 4925000-8100000 262 * ab: 4600000-6100000 263 * ibb: 800000-5400000 264 */ 265 regulators-1 { 266 compatible = "qcom,pm8150l-rpmh-regulators"; 267 qcom,pmic-id = "c"; 268 269 vdd-s1-supply = <&vph_pwr>; 270 vdd-s2-supply = <&vph_pwr>; 271 vdd-s3-supply = <&vph_pwr>; 272 vdd-s4-supply = <&vph_pwr>; 273 vdd-s5-supply = <&vph_pwr>; 274 vdd-s6-supply = <&vph_pwr>; 275 vdd-s7-supply = <&vph_pwr>; 276 vdd-s8-supply = <&vph_pwr>; 277 vdd-l1-l8-supply = <&vreg_s4a_1p8>; 278 vdd-l2-l3-supply = <&vreg_s8c_1p2>; 279 vdd-l4-l5-l6-supply = <&vreg_bob>; 280 vdd-l7-l11-supply = <&vreg_bob>; 281 vdd-l9-l10-supply = <&vreg_bob>; 282 vdd-bob-supply = <&vph_pwr>; 283 284 vreg_bob: bob { 285 regulator-name = "vreg_bob"; 286 regulator-min-microvolt = <3350000>; 287 regulator-max-microvolt = <3960000>; 288 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; 289 }; 290 291 /* 292 * S1-S6 are ARCs: 293 * (S1+S2) - gfx.lvl, 294 * S3 - mx.lvl, 295 * (S4+S5) - mmcx.lvl, 296 * S6 - ebi.lvl 297 */ 298 299 vreg_s7c_0p35: smps7 { 300 regulator-name = "vreg_s7c_0p35"; 301 regulator-min-microvolt = <348000>; 302 regulator-max-microvolt = <1000000>; 303 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 304 }; 305 306 vreg_s8c_1p2: smps8 { 307 regulator-name = "vreg_s8c_1p2"; 308 regulator-min-microvolt = <1200000>; 309 regulator-max-microvolt = <1400000>; 310 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 311 }; 312 313 vreg_l1c_1p8: ldo1 { 314 regulator-name = "vreg_l1c_1p8"; 315 regulator-min-microvolt = <1800000>; 316 regulator-max-microvolt = <1800000>; 317 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 318 }; 319 320 /* L2-4 are unused. */ 321 322 vreg_l5c_1p8: ldo5 { 323 regulator-name = "vreg_l5c_1p8"; 324 regulator-min-microvolt = <1800000>; 325 regulator-max-microvolt = <2800000>; 326 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 327 }; 328 329 vreg_l6c_2p9: ldo6 { 330 regulator-name = "vreg_l6c_2p9"; 331 regulator-min-microvolt = <1800000>; 332 regulator-max-microvolt = <2960000>; 333 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 334 regulator-allow-set-load; 335 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 336 RPMH_REGULATOR_MODE_HPM>; 337 }; 338 339 vreg_l7c_2p85: ldo7 { 340 regulator-name = "vreg_l7c_2p85"; 341 regulator-min-microvolt = <2856000>; 342 regulator-max-microvolt = <3104000>; 343 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 344 }; 345 346 vreg_l8c_1p8: ldo8 { 347 regulator-name = "vreg_l8c_1p8"; 348 regulator-min-microvolt = <1800000>; 349 regulator-max-microvolt = <1800000>; 350 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 351 }; 352 353 vreg_l9c_2p9: ldo9 { 354 regulator-name = "vreg_l9c_2p9"; 355 regulator-min-microvolt = <2704000>; 356 regulator-max-microvolt = <2960000>; 357 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 358 regulator-allow-set-load; 359 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 360 RPMH_REGULATOR_MODE_HPM>; 361 }; 362 363 vreg_l10c_3p3: ldo10 { 364 regulator-name = "vreg_l10c_3p3"; 365 regulator-min-microvolt = <3296000>; 366 regulator-max-microvolt = <3296000>; 367 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 368 }; 369 370 vreg_l11c_3p0: ldo11 { 371 regulator-name = "vreg_l11c_3p0"; 372 regulator-min-microvolt = <3000000>; 373 regulator-max-microvolt = <3000000>; 374 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 375 }; 376 }; 377 378 regulators-2 { 379 compatible = "qcom,pm8009-rpmh-regulators"; 380 qcom,pmic-id = "f"; 381 382 vdd-s1-supply = <&vph_pwr>; 383 vdd-s2-supply = <&vreg_bob>; 384 vdd-l2-supply = <&vreg_s8c_1p2>; 385 vdd-l5-l6-supply = <&vreg_bob>; 386 vdd-l7-supply = <&vreg_s4a_1p8>; 387 388 vreg_s1f_1p2: smps1 { 389 regulator-name = "vreg_s1f_1p2"; 390 regulator-min-microvolt = <1200000>; 391 regulator-max-microvolt = <1200000>; 392 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 393 }; 394 395 vreg_s2f_0p5: smps2 { 396 regulator-name = "vreg_s2f_0p5"; 397 regulator-min-microvolt = <512000>; 398 regulator-max-microvolt = <1100000>; 399 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 400 }; 401 402 /* L1 is unused. */ 403 404 vreg_l2f_1p3: ldo2 { 405 regulator-name = "vreg_l2f_1p3"; 406 regulator-min-microvolt = <1304000>; 407 regulator-max-microvolt = <1304000>; 408 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 409 }; 410 411 /* L3 & L4 are unused. */ 412 413 vreg_l5f_2p8: ldo5 { 414 regulator-name = "vreg_l5f_2p85"; 415 regulator-min-microvolt = <2800000>; 416 regulator-max-microvolt = <2800000>; 417 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 418 }; 419 420 vreg_l6f_2p8: ldo6 { 421 regulator-name = "vreg_l6f_2p8"; 422 regulator-min-microvolt = <2800000>; 423 regulator-max-microvolt = <2800000>; 424 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 425 }; 426 427 vreg_l7f_1p8: ldo7 { 428 regulator-name = "vreg_l7f_1p8"; 429 regulator-min-microvolt = <1800000>; 430 regulator-max-microvolt = <1800000>; 431 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 432 }; 433 }; 434}; 435 436&cdsp { 437 status = "okay"; 438}; 439 440&gpi_dma0 { 441 status = "okay"; 442}; 443 444&gpi_dma1 { 445 status = "okay"; 446}; 447 448&gpi_dma2 { 449 status = "okay"; 450}; 451 452&i2c1 { 453 status = "okay"; 454 clock-frequency = <400000>; 455 456 nfc@28 { 457 compatible = "nxp,nxp-nci-i2c"; 458 reg = <0x28>; 459 460 interrupt-parent = <&tlmm>; 461 interrupts = <111 IRQ_TYPE_EDGE_RISING>; 462 463 enable-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>; 464 firmware-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; 465 }; 466}; 467 468&i2c2 { 469 status = "okay"; 470 clock-frequency = <1000000>; 471 472 cs35l41_l: speaker-amp@40 { 473 compatible = "cirrus,cs35l41"; 474 reg = <0x40>; 475 interrupt-parent = <&tlmm>; 476 interrupts = <11 IRQ_TYPE_LEVEL_LOW>; 477 reset-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>; 478 cirrus,boost-peak-milliamp = <4000>; 479 cirrus,boost-ind-nanohenry = <1000>; 480 cirrus,boost-cap-microfarad = <15>; 481 cirrus,asp-sdout-hiz = <3>; 482 cirrus,gpio2-src-select = <2>; 483 cirrus,gpio2-output-enable; 484 #sound-dai-cells = <1>; 485 }; 486 487 cs35l41_r: speaker-amp@41 { 488 compatible = "cirrus,cs35l41"; 489 reg = <0x41>; 490 interrupt-parent = <&tlmm>; 491 interrupts = <11 IRQ_TYPE_LEVEL_LOW>; 492 reset-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>; 493 cirrus,boost-peak-milliamp = <4000>; 494 cirrus,boost-ind-nanohenry = <1000>; 495 cirrus,boost-cap-microfarad = <15>; 496 cirrus,asp-sdout-hiz = <3>; 497 cirrus,gpio2-src-select = <2>; 498 cirrus,gpio2-output-enable; 499 #sound-dai-cells = <1>; 500 }; 501}; 502 503&i2c9 { 504 status = "okay"; 505 clock-frequency = <400000>; 506 507 /* AMS TCS3490 RGB+IR color sensor @ 72 */ 508}; 509 510&i2c13 { 511 status = "okay"; 512 clock-frequency = <400000>; 513 514 touchscreen@48 { 515 compatible = "samsung,s6sy761"; 516 reg = <0x48>; 517 interrupt-parent = <&tlmm>; 518 interrupts = <39 0x2008>; 519 /* It's "vddio" downstream but it works anyway! */ 520 vdd-supply = <&vreg_l1c_1p8>; 521 avdd-supply = <&vreg_l10c_3p3>; 522 523 pinctrl-names = "default"; 524 pinctrl-0 = <&ts_int_default>; 525 }; 526}; 527 528&i2c15 { 529 status = "okay"; 530 clock-frequency = <400000>; 531 532 /* Qcom SMB1390 @ 10 */ 533 /* Qcom SMB1390_slave @ 18 */ 534 /* HALO HL6111R Qi charger @ 25 */ 535}; 536 537&pcie0 { 538 status = "okay"; 539}; 540 541&pcie0_phy { 542 status = "okay"; 543 544 vdda-phy-supply = <&vreg_l5a_0p88>; 545 vdda-pll-supply = <&vreg_l9a_1p2>; 546}; 547 548&pcie2 { 549 status = "okay"; 550 551 pinctrl-0 = <&pcie2_default_state &mdm2ap_default &ap2mdm_default>; 552}; 553 554&pcie2_phy { 555 status = "okay"; 556 557 vdda-phy-supply = <&vreg_l5a_0p88>; 558 vdda-pll-supply = <&vreg_l9a_1p2>; 559}; 560 561&pm8150_gpios { 562 vol_down_n: vol-down-n-state { 563 pins = "gpio1"; 564 function = "normal"; 565 power-source = <0>; 566 bias-pull-up; 567 input-enable; 568 }; 569}; 570 571&pm8150b_gpios { 572 snapshot_n: snapshot-n-state { 573 pins = "gpio1"; 574 function = "normal"; 575 power-source = <0>; 576 bias-pull-up; 577 input-enable; 578 }; 579 580 focus_n: focus-n-state { 581 pins = "gpio2"; 582 function = "normal"; 583 power-source = <0>; 584 bias-pull-up; 585 input-enable; 586 }; 587}; 588 589&pon_pwrkey { 590 status = "okay"; 591}; 592 593&pon_resin { 594 status = "okay"; 595 596 linux,code = <KEY_VOLUMEUP>; 597}; 598 599&qupv3_id_0 { 600 status = "okay"; 601}; 602 603&qupv3_id_1 { 604 status = "okay"; 605}; 606 607&qupv3_id_2 { 608 status = "okay"; 609}; 610 611&sdhc_2 { 612 status = "okay"; 613 614 cd-gpios = <&tlmm 77 GPIO_ACTIVE_HIGH>; 615 pinctrl-names = "default", "sleep"; 616 pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>; 617 pinctrl-1 = <&sdc2_sleep_state &sdc2_card_det_n>; 618 vmmc-supply = <&vreg_l9c_2p9>; 619 vqmmc-supply = <&vreg_l6c_2p9>; 620 bus-width = <4>; 621 no-sdio; 622 no-mmc; 623}; 624 625&slpi { 626 status = "okay"; 627}; 628 629&tlmm { 630 gpio-reserved-ranges = <40 4>, <52 4>; 631 632 sdc2_default_state: sdc2-default-state { 633 clk-pins { 634 pins = "sdc2_clk"; 635 drive-strength = <16>; 636 bias-disable; 637 }; 638 639 cmd-pins { 640 pins = "sdc2_cmd"; 641 drive-strength = <16>; 642 bias-pull-up; 643 }; 644 645 data-pins { 646 pins = "sdc2_data"; 647 drive-strength = <16>; 648 bias-pull-up; 649 }; 650 }; 651 652 mdm2ap_default: mdm2ap-default-state { 653 pins = "gpio1", "gpio3"; 654 function = "gpio"; 655 drive-strength = <8>; 656 bias-disable; 657 }; 658 659 ts_int_default: ts-int-default-state { 660 pins = "gpio39"; 661 function = "gpio"; 662 drive-strength = <2>; 663 bias-disable; 664 }; 665 666 ap2mdm_default: ap2mdm-default-state { 667 pins = "gpio56", "gpio57"; 668 function = "gpio"; 669 drive-strength = <16>; 670 bias-disable; 671 }; 672 673 sdc2_card_det_n: sd-card-det-n-state { 674 pins = "gpio77"; 675 function = "gpio"; 676 bias-pull-up; 677 drive-strength = <2>; 678 }; 679}; 680 681&uart12 { 682 status = "okay"; 683}; 684 685/* BIG WARNING! DO NOT TOUCH UFS, YOUR DEVICE WILL DIE! */ 686&ufs_mem_hc { status = "disabled"; }; 687&ufs_mem_phy { status = "disabled"; }; 688 689&usb_1 { 690 status = "okay"; 691}; 692 693&usb_1_dwc3 { 694 dr_mode = "peripheral"; 695}; 696 697&usb_1_hsphy { 698 status = "okay"; 699 700 vdda-pll-supply = <&vreg_l5a_0p88>; 701 vdda18-supply = <&vreg_l12a_1p8>; 702 vdda33-supply = <&vreg_l2a_3p1>; 703}; 704 705&usb_1_qmpphy { 706 status = "okay"; 707 708 vdda-phy-supply = <&vreg_l9a_1p2>; 709 vdda-pll-supply = <&vreg_l18a_0p9>; 710}; 711 712&venus { 713 firmware-name = "qcom/sm8250/Sony/edo/venus.mbn"; 714 status = "okay"; 715}; 716