xref: /linux/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx206.dts (revision c532de5a67a70f8533d495f8f2aaa9a0491c3ad0) 
1// SPDX-License-Identifier: BSD-3-Clause
2/*
3 * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
4 */
5
6/dts-v1/;
7
8#include "sm8250-sony-xperia-edo.dtsi"
9
10/ {
11	model = "Sony Xperia 5 II";
12	compatible = "sony,pdx206-generic", "qcom,sm8250";
13	chassis-type = "handset";
14};
15
16&framebuffer {
17	width = <1080>;
18	height = <2520>;
19	stride = <(1080 * 4)>;
20};
21
22&gpio_keys {
23	pinctrl-0 = <&focus_n &snapshot_n &vol_down_n &g_assist_n>;
24
25	g-assist-key {
26		label = "Google Assistant Key";
27		linux,code = <KEY_LEFTMETA>;
28		gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
29		debounce-interval = <15>;
30		linux,can-disable;
31		wakeup-source;
32	};
33};
34
35&pm8009_gpios {
36	gpio-line-names = "NC", /* GPIO_1 */
37			  "NC",
38			  "WIDEC_PWR_EN",
39			  "NC";
40};
41
42&pm8150_gpios {
43	gpio-line-names = "VOL_DOWN_N", /* GPIO_1 */
44			  "OPTION_2",
45			  "NC",
46			  "PM_SLP_CLK_IN",
47			  "OPTION_1",
48			  "G_ASSIST_N",
49			  "NC",
50			  "SP_ARI_PWR_ALARM",
51			  "NC",
52			  "NC"; /* GPIO_10 */
53
54	g_assist_n: g-assist-n-state {
55		pins = "gpio6";
56		function = "normal";
57		power-source = <1>;
58		bias-pull-up;
59		input-enable;
60	};
61};
62
63&pm8150b_gpios {
64	gpio-line-names = "SNAPSHOT_N", /* GPIO_1 */
65			  "FOCUS_N",
66			  "NC",
67			  "NC",
68			  "RF_LCD_ID_EN",
69			  "NC",
70			  "NC",
71			  "LCD_ID",
72			  "NC",
73			  "NC", /* GPIO_10 */
74			  "NC",
75			  "RF_ID";
76};
77
78&pm8150l_gpios {
79	gpio-line-names = "NC", /* GPIO_1 */
80			  "PM3003A_EN",
81			  "NC",
82			  "NC",
83			  "NC",
84			  "AUX2_THERM",
85			  "BB_HP_EN",
86			  "FP_LDO_EN",
87			  "PMX_RESET_N",
88			  "NC", /* GPIO_10 */
89			  "NC",
90			  "PM3003A_MODE";
91};
92
93&tlmm {
94	gpio-line-names = "AP_CTI_IN", /* GPIO_0 */
95			  "MDM2AP_ERR_FATAL",
96			  "AP_CTI_OUT",
97			  "MDM2AP_STATUS",
98			  "NFC_I2C_SDA",
99			  "NFC_I2C_SCL",
100			  "NFC_EN",
101			  "NFC_CLK_REQ",
102			  "NFC_ESE_PWR_REQ",
103			  "DVDT_WRT_DET_AND",
104			  "SPK_AMP_RESET_N", /* GPIO_10 */
105			  "SPK_AMP_INT_N",
106			  "APPS_I2C_1_SDA",
107			  "APPS_I2C_1_SCL",
108			  "NC",
109			  "TX_GTR_THRES_IN",
110			  "HST_BT_UART_CTS",
111			  "HST_BT_UART_RFR",
112			  "HST_BT_UART_TX",
113			  "HST_BT_UART_RX",
114			  "HST_WLAN_EN", /* GPIO_20 */
115			  "HST_BT_EN",
116			  "RGBC_IR_PWR_EN",
117			  "FP_INT_N",
118			  "NC",
119			  "NC",
120			  "NC",
121			  "NC",
122			  "NFC_ESE_SPI_MISO",
123			  "NFC_ESE_SPI_MOSI",
124			  "NFC_ESE_SPI_SCLK", /* GPIO_30 */
125			  "NFC_ESE_SPI_CS_N",
126			  "WCD_RST_N",
127			  "NC",
128			  "SDM_DEBUG_UART_TX",
129			  "SDM_DEBUG_UART_RX",
130			  "TS_I2C_SDA",
131			  "TS_I2C_SCL",
132			  "TS_INT_N",
133			  "FP_SPI_MISO", /* GPIO_40 */
134			  "FP_SPI_MOSI",
135			  "FP_SPI_SCLK",
136			  "FP_SPI_CS_N",
137			  "APPS_I2C_0_SDA",
138			  "APPS_I2C_0_SCL",
139			  "DISP_ERR_FG",
140			  "UIM2_DETECT_EN",
141			  "NC",
142			  "NC",
143			  "NC", /* GPIO_50 */
144			  "NC",
145			  "MDM_UART_CTS",
146			  "MDM_UART_RFR",
147			  "MDM_UART_TX",
148			  "MDM_UART_RX",
149			  "AP2MDM_STATUS",
150			  "AP2MDM_ERR_FATAL",
151			  "MDM_IPC_HS_UART_TX",
152			  "MDM_IPC_HS_UART_RX",
153			  "NC", /* GPIO_60 */
154			  "NC",
155			  "NC",
156			  "NC",
157			  "NC",
158			  "USB_CC_DIR",
159			  "DISP_VSYNC",
160			  "NC",
161			  "NC",
162			  "CAM_PWR_B_CS",
163			  "NC", /* GPIO_70 */
164			  "FRONTC_PWR_EN",
165			  "SBU_SW_SEL",
166			  "SBU_SW_OE",
167			  "FP_RESET_N",
168			  "FP_RESET_N",
169			  "DISP_RESET_N",
170			  "DEBUG_GPIO0",
171			  "TRAY_DET",
172			  "CAM2_RST_N",
173			  "PCIE0_RST_N",
174			  "PCIE0_CLK_REQ_N", /* GPIO_80 */
175			  "PCIE0_WAKE_N",
176			  "DVDT_ENABLE",
177			  "DVDT_WRT_DET_OR",
178			  "NC",
179			  "PCIE2_RST_N",
180			  "PCIE2_CLK_REQ_N",
181			  "PCIE2_WAKE_N",
182			  "MDM_VFR_IRQ0",
183			  "MDM_VFR_IRQ1",
184			  "SW_SERVICE", /* GPIO_90 */
185			  "CAM_SOF",
186			  "CAM1_RST_N",
187			  "CAM0_RST_N",
188			  "CAM0_MCLK",
189			  "CAM1_MCLK",
190			  "CAM2_MCLK",
191			  "CAM3_MCLK",
192			  "NC",
193			  "NC",
194			  "NC", /* GPIO_100 */
195			  "CCI0_I2C_SDA",
196			  "CCI0_I2C_SCL",
197			  "CCI1_I2C_SDA",
198			  "CCI1_I2C_SCL_",
199			  "CCI2_I2C_SDA",
200			  "CCI2_I2C_SCL",
201			  "CCI3_I2C_SDA",
202			  "CCI3_I2C_SCL",
203			  "CAM3_RST_N",
204			  "NFC_DWL_REQ", /* GPIO_110 */
205			  "NFC_IRQ",
206			  "XVS",
207			  "NC",
208			  "RF_ID_EXTENSION",
209			  "SPK_AMP_I2C_SDA",
210			  "SPK_AMP_I2C_SCL",
211			  "NC",
212			  "NC",
213			  "NC",
214			  "NC",
215			  "ACC_COVER_OPEN",
216			  "ALS_PROX_INT_N",
217			  "ACCEL_INT",
218			  "WLAN_SW_CTRL",
219			  "CAMSENSOR_I2C_SDA",
220			  "CAMSENSOR_I2C_SCL",
221			  "UDON_SWITCH_SEL",
222			  "WDOG_DISABLE",
223			  "BAROMETER_INT",
224			  "NC", /* GPIO_130 */
225			  "NC",
226			  "FORCED_USB_BOOT",
227			  "NC",
228			  "NC",
229			  "NC",
230			  "NC",
231			  "NC",
232			  "RGBC_IR_INT",
233			  "NC",
234			  "NC", /* GPIO_140 */
235			  "NC",
236			  "BT_SLIMBUS_CLK",
237			  "BT_SLIMBUS_DATA",
238			  "HW_ID_0",
239			  "HW_ID_1",
240			  "WCD_SWR_TX_CLK",
241			  "WCD_SWR_TX_DATA0",
242			  "WCD_SWR_TX_DATA1",
243			  "WCD_SWR_RX_CLK",
244			  "WCD_SWR_RX_DATA0", /* GPIO_150 */
245			  "WCD_SWR_RX_DATA1",
246			  "SDM_DMIC_CLK1",
247			  "SDM_DMIC_DATA1",
248			  "SDM_DMIC_CLK2",
249			  "SDM_DMIC_DATA2",
250			  "SPK_AMP_I2S_CLK",
251			  "SPK_AMP_I2S_WS",
252			  "SPK_AMP_I2S_ASP_DIN",
253			  "SPK_AMP_I2S_ASP_DOUT",
254			  "COMPASS_I2C_SDA", /* GPIO_160 */
255			  "COMPASS_I2C_SCL",
256			  "NC",
257			  "NC",
258			  "SSC_SPI_1_MISO",
259			  "SSC_SPI_1_MOSI",
260			  "SSC_SPI_1_CLK",
261			  "SSC_SPI_1_CS_N",
262			  "NC",
263			  "NC",
264			  "SSC_SENSOR_I2C_SDA", /* GPIO_170 */
265			  "SSC_SENSOR_I2C_SCL",
266			  "NC",
267			  "NC",
268			  "NC",
269			  "NC",
270			  "HST_BLE_SNS_UART6_TX",
271			  "HST_BLE_SNS_UART6_RX",
272			  "HST_WLAN_UART_TX",
273			  "HST_WLAN_UART_RX";
274};
275
276&vreg_l2f_1p3 {
277	regulator-min-microvolt = <1200000>;
278	regulator-max-microvolt = <1200000>;
279};
280