1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> 4 */ 5 6#include <dt-bindings/input/input.h> 7#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> 8#include <dt-bindings/regulator/qcom,rpmh-regulator.h> 9#include "sdm845.dtsi" 10#include "pm8005.dtsi" 11#include "pm8998.dtsi" 12#include "pmi8998.dtsi" 13 14/ { 15 qcom,msm-id = <321 0x20001>; /* SDM845 v2.1 */ 16 qcom,board-id = <8 0>; 17 18 aliases { 19 serial0 = &uart6; 20 serial1 = &uart9; 21 }; 22 23 chosen { 24 stdout-path = "serial0:115200n8"; 25 }; 26 27 gpio-keys { 28 compatible = "gpio-keys"; 29 30 pinctrl-0 = <&focus_n &snapshot_n &vol_down_n &vol_up_n>; 31 pinctrl-names = "default"; 32 33 key-camera-focus { 34 label = "Camera Focus"; 35 gpios = <&pm8998_gpios 2 GPIO_ACTIVE_LOW>; 36 linux,code = <KEY_CAMERA_FOCUS>; 37 debounce-interval = <15>; 38 linux,can-disable; 39 wakeup-source; 40 }; 41 42 key-camera-snapshot { 43 label = "Camera Snapshot"; 44 gpios = <&pm8998_gpios 7 GPIO_ACTIVE_LOW>; 45 linux,code = <KEY_CAMERA>; 46 debounce-interval = <15>; 47 linux,can-disable; 48 wakeup-source; 49 }; 50 51 key-volume-down { 52 label = "Volume Down"; 53 gpios = <&pm8998_gpios 5 GPIO_ACTIVE_LOW>; 54 linux,code = <KEY_VOLUMEDOWN>; 55 debounce-interval = <15>; 56 linux,can-disable; 57 wakeup-source; 58 }; 59 60 key-volume-up { 61 label = "Volume Up"; 62 gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>; 63 linux,code = <KEY_VOLUMEUP>; 64 debounce-interval = <15>; 65 linux,can-disable; 66 wakeup-source; 67 }; 68 }; 69 70 vph_pwr: vph-pwr-regulator { 71 compatible = "regulator-fixed"; 72 regulator-name = "vph_pwr"; 73 regulator-min-microvolt = <3700000>; 74 regulator-max-microvolt = <3700000>; 75 }; 76 77 vreg_s4a_1p8: pm8998-smps4 { 78 compatible = "regulator-fixed"; 79 regulator-name = "vreg_s4a_1p8"; 80 81 regulator-min-microvolt = <1800000>; 82 regulator-max-microvolt = <1800000>; 83 84 regulator-always-on; 85 regulator-boot-on; 86 87 vin-supply = <&vph_pwr>; 88 }; 89 90 reserved-memory { 91 /* SONY was cool and didn't diverge from MTP this time, yay! */ 92 cont_splash_mem: memory@9d400000 { 93 reg = <0x0 0x9d400000 0x0 0x2400000>; 94 no-map; 95 }; 96 97 ramoops@ffc00000 { 98 compatible = "ramoops"; 99 reg = <0x0 0xffc00000 0x0 0x100000>; 100 record-size = <0x10000>; 101 console-size = <0x60000>; 102 ftrace-size = <0x10000>; 103 pmsg-size = <0x20000>; 104 ecc-size = <16>; 105 no-map; 106 }; 107 }; 108}; 109 110&adsp_pas { 111 firmware-name = "qcom/sdm845/Sony/tama/adsp.mbn"; 112 status = "okay"; 113}; 114 115&apps_rsc { 116 regulators-0 { 117 compatible = "qcom,pm8998-rpmh-regulators"; 118 qcom,pmic-id = "a"; 119 120 vdd-s1-supply = <&vph_pwr>; 121 vdd-s2-supply = <&vph_pwr>; 122 vdd-s3-supply = <&vph_pwr>; 123 vdd-s4-supply = <&vph_pwr>; 124 vdd-s5-supply = <&vph_pwr>; 125 vdd-s6-supply = <&vph_pwr>; 126 vdd-s7-supply = <&vph_pwr>; 127 vdd-s8-supply = <&vph_pwr>; 128 vdd-s9-supply = <&vph_pwr>; 129 vdd-s10-supply = <&vph_pwr>; 130 vdd-s11-supply = <&vph_pwr>; 131 vdd-s12-supply = <&vph_pwr>; 132 vdd-s13-supply = <&vph_pwr>; 133 vdd-l1-l27-supply = <&vreg_s7a_0p9>; 134 vdd-l2-l8-l17-supply = <&vreg_s3a_1p3>; 135 vdd-l3-l11-supply = <&vreg_s7a_0p9>; 136 vdd-l4-l5-supply = <&vreg_s7a_0p9>; 137 vdd-l6-supply = <&vph_pwr>; 138 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>; 139 vdd-l9-supply = <&vreg_s5a_1p9>; 140 vdd-l10-l23-l25-supply = <&src_vreg_bob>; 141 vdd-l13-l19-l21-supply = <&src_vreg_bob>; 142 vdd-l16-l28-supply = <&src_vreg_bob>; 143 vdd-l18-l22-supply = <&src_vreg_bob>; 144 vdd-l20-l24-supply = <&src_vreg_bob>; 145 vdd-l26-supply = <&vreg_s3a_1p3>; 146 vin-lvs-1-2-supply = <&vreg_s4a_1p8>; 147 148 vreg_s2a_1p1: smps2 { 149 regulator-min-microvolt = <1100000>; 150 regulator-max-microvolt = <1100000>; 151 }; 152 153 vreg_s3a_1p3: smps3 { 154 regulator-min-microvolt = <1352000>; 155 regulator-max-microvolt = <1352000>; 156 }; 157 158 vreg_s5a_1p9: smps5 { 159 regulator-min-microvolt = <1904000>; 160 regulator-max-microvolt = <2040000>; 161 }; 162 163 vreg_s7a_0p9: smps7 { 164 regulator-min-microvolt = <900000>; 165 regulator-max-microvolt = <1028000>; 166 }; 167 168 vreg_l1a_0p9: ldo1 { 169 regulator-min-microvolt = <880000>; 170 regulator-max-microvolt = <880000>; 171 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 172 }; 173 174 vreg_l2a_1p2: ldo2 { 175 regulator-min-microvolt = <1200000>; 176 regulator-max-microvolt = <1200000>; 177 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 178 regulator-always-on; 179 }; 180 181 vreg_l3a_1p0: ldo3 { 182 regulator-min-microvolt = <1000000>; 183 regulator-max-microvolt = <1000000>; 184 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 185 }; 186 187 vreg_l5a_0p8: ldo5 { 188 regulator-min-microvolt = <800000>; 189 regulator-max-microvolt = <800000>; 190 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 191 }; 192 193 vreg_l6a_1p8: ldo6 { 194 regulator-min-microvolt = <1856000>; 195 regulator-max-microvolt = <1856000>; 196 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 197 }; 198 199 vreg_l7a_1p8: ldo7 { 200 regulator-min-microvolt = <1800000>; 201 regulator-max-microvolt = <1800000>; 202 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 203 }; 204 205 vreg_l8a_1p2: ldo8 { 206 regulator-min-microvolt = <1200000>; 207 regulator-max-microvolt = <1248000>; 208 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 209 }; 210 211 vreg_l9a_1p7: ldo9 { 212 regulator-min-microvolt = <1704000>; 213 regulator-max-microvolt = <2928000>; 214 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 215 }; 216 217 vreg_l10a_1p7: ldo10 { 218 regulator-min-microvolt = <1704000>; 219 regulator-max-microvolt = <2928000>; 220 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 221 }; 222 223 vreg_l11a_1p0: ldo11 { 224 regulator-min-microvolt = <1000000>; 225 regulator-max-microvolt = <1048000>; 226 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 227 }; 228 229 vreg_l12a_1p8: ldo12 { 230 regulator-min-microvolt = <1800000>; 231 regulator-max-microvolt = <1800000>; 232 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 233 }; 234 235 vreg_l13a_1p8: ldo13 { 236 regulator-min-microvolt = <1800000>; 237 regulator-max-microvolt = <2960000>; 238 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 239 }; 240 241 vreg_l14a_1p8: ldo14 { 242 regulator-min-microvolt = <1800000>; 243 regulator-max-microvolt = <1800000>; 244 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 245 regulator-system-load = <62000>; 246 }; 247 248 vreg_l15a_1p8: ldo15 { 249 regulator-min-microvolt = <1800000>; 250 regulator-max-microvolt = <1800000>; 251 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 252 }; 253 254 vreg_l16a_2p7: ldo16 { 255 regulator-min-microvolt = <2704000>; 256 regulator-max-microvolt = <2704000>; 257 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 258 }; 259 260 vreg_l17a_1p3: ldo17 { 261 regulator-min-microvolt = <1304000>; 262 regulator-max-microvolt = <1304000>; 263 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 264 }; 265 266 vreg_l18a_2p7: ldo18 { 267 regulator-min-microvolt = <2704000>; 268 regulator-max-microvolt = <2960000>; 269 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 270 }; 271 272 vreg_l19a_2p7: ldo19 { 273 regulator-min-microvolt = <2700000>; 274 regulator-max-microvolt = <2700000>; 275 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 276 277 /* 278 * The driver *really* doesn't want this regualtor to exist, 279 * saying that it could not get the current voltage (-ENOTRECOVERABLE) 280 * even though it surely is used on these devices (as a voltage 281 * source for camera autofocus) 282 */ 283 status = "disabled"; 284 }; 285 286 vreg_l20a_2p7: ldo20 { 287 regulator-min-microvolt = <2704000>; 288 regulator-max-microvolt = <2960000>; 289 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 290 }; 291 292 vreg_l21a_2p7: ldo21 { 293 regulator-min-microvolt = <2704000>; 294 regulator-max-microvolt = <2960000>; 295 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 296 }; 297 298 vreg_l22a_2p8: ldo22 { 299 regulator-min-microvolt = <2800000>; 300 regulator-max-microvolt = <2800000>; 301 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 302 }; 303 304 vreg_l23a_3p0: ldo23 { 305 regulator-min-microvolt = <3000000>; 306 regulator-max-microvolt = <3312000>; 307 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 308 }; 309 310 vreg_l24a_3p1: ldo24 { 311 regulator-min-microvolt = <3088000>; 312 regulator-max-microvolt = <3088000>; 313 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 314 }; 315 316 vreg_l25a_3p0: ldo25 { 317 regulator-min-microvolt = <3000000>; 318 regulator-max-microvolt = <3312000>; 319 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 320 }; 321 322 vreg_l26a_1p2: ldo26 { 323 regulator-min-microvolt = <1200000>; 324 regulator-max-microvolt = <1200000>; 325 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 326 }; 327 328 vreg_l28a_2p8: ldo28 { 329 regulator-min-microvolt = <2856000>; 330 regulator-max-microvolt = <3008000>; 331 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 332 regulator-system-load = <100000>; 333 }; 334 335 vreg_lvs1a_1p8: lvs1 { 336 regulator-min-microvolt = <1800000>; 337 regulator-max-microvolt = <1800000>; 338 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 339 }; 340 341 vreg_lvs2a_1p8: lvs2 { 342 regulator-min-microvolt = <1800000>; 343 regulator-max-microvolt = <1800000>; 344 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 345 }; 346 }; 347 348 regulators-1 { 349 compatible = "qcom,pmi8998-rpmh-regulators"; 350 qcom,pmic-id = "b"; 351 352 src_vreg_bob: bob { 353 regulator-min-microvolt = <3312000>; 354 regulator-max-microvolt = <3600000>; 355 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 356 }; 357 }; 358 359 regulators-2 { 360 compatible = "qcom,pm8005-rpmh-regulators"; 361 qcom,pmic-id = "c"; 362 363 vdd-s1-supply = <&vph_pwr>; 364 vdd-s2-supply = <&vph_pwr>; 365 vdd-s3-supply = <&vph_pwr>; 366 vdd-s4-supply = <&vph_pwr>; 367 368 vreg_s3c_0p6: smps3 { 369 regulator-min-microvolt = <600000>; 370 regulator-max-microvolt = <600000>; 371 }; 372 }; 373}; 374 375&cdsp_pas { 376 firmware-name = "qcom/sdm845/Sony/tama/cdsp.mbn"; 377 status = "okay"; 378}; 379 380&gcc { 381 protected-clocks = <GCC_QSPI_CORE_CLK>, 382 <GCC_QSPI_CORE_CLK_SRC>, 383 <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, 384 <GCC_LPASS_Q6_AXI_CLK>, 385 <GCC_LPASS_SWAY_CLK>; 386}; 387 388&gmu { 389 status = "okay"; 390}; 391 392&gpi_dma0 { 393 status = "okay"; 394}; 395 396&gpi_dma1 { 397 status = "okay"; 398}; 399 400&gpu { 401 status = "okay"; 402 403 zap-shader { 404 memory-region = <&gpu_mem>; 405 firmware-name = "qcom/sdm845/Sony/tama/a630_zap.mbn"; 406 }; 407}; 408 409&i2c5 { 410 clock-frequency = <400000>; 411 status = "okay"; 412 413 touchscreen: touchscreen@2c { 414 compatible = "syna,rmi4-i2c"; 415 reg = <0x2c>; 416 417 interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>; 418 vdd-supply = <&vreg_l14a_1p8>; 419 /* 420 * This is a blatant abuse of OF, but the panel driver *needs* 421 * to probe first, as the power/gpio switching needs to be precisely 422 * timed in order for both the display and touch panel to function properly. 423 */ 424 incell-supply = <&panel>; 425 426 syna,reset-delay-ms = <220>; 427 syna,startup-delay-ms = <1000>; 428 429 pinctrl-0 = <&ts_default>; 430 pinctrl-1 = <&ts_sleep>; 431 pinctrl-names = "default", "sleep"; 432 433 #address-cells = <1>; 434 #size-cells = <0>; 435 436 rmi4-f01@1 { 437 reg = <0x01>; 438 syna,nosleep-mode = <1>; 439 }; 440 441 rmi4-f12@12 { 442 reg = <0x12>; 443 syna,sensor-type = <1>; 444 }; 445 }; 446}; 447 448&i2c10 { 449 status = "okay"; 450 clock-frequency = <400000>; 451 452 /* Qcom SMB1355 @ 8, c */ 453 /* NXP PN547 NFC @ 28 */ 454 /* Renesas IDTP9221 Qi charger @ 61 */ 455}; 456 457&i2c14 { 458 status = "okay"; 459 clock-frequency = <400000>; 460 461 /* SONY ToF sensor @ 52 */ 462 /* AMS TCS3490 RGB+IR color sensor @ 72 */ 463}; 464 465&ibb { 466 qcom,discharge-resistor-kohms = <300>; 467 regulator-min-microvolt = <5500000>; 468 regulator-max-microvolt = <5700000>; 469 regulator-min-microamp = <0>; 470 regulator-max-microamp = <800000>; 471 regulator-over-current-protection; 472 regulator-soft-start; 473 regulator-pull-down; 474}; 475 476&lab { 477 regulator-min-microvolt = <5500000>; 478 regulator-max-microvolt = <5700000>; 479 regulator-min-microamp = <200000>; 480 regulator-max-microamp = <200000>; 481 regulator-over-current-protection; 482 regulator-soft-start; 483 regulator-pull-down; 484}; 485 486&mdss { 487 status = "okay"; 488}; 489 490&mdss_dsi0 { 491 vdda-supply = <&vreg_l26a_1p2>; 492 status = "okay"; 493 494 panel: panel@0 { 495 /* The compatible is assigned in device DTs. */ 496 reg = <0>; 497 498 backlight = <&pmi8998_wled>; 499 vddio-supply = <&vreg_l14a_1p8>; 500 vsp-supply = <&lab>; 501 vsn-supply = <&ibb>; 502 panel-reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>; 503 touch-reset-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>; 504 505 pinctrl-0 = <&sde_dsi_active &sde_te_active_sleep>; 506 pinctrl-1 = <&sde_dsi_sleep &sde_te_active_sleep>; 507 pinctrl-names = "default", "sleep"; 508 509 port { 510 panel_in: endpoint { 511 remote-endpoint = <&mdss_dsi0_out>; 512 }; 513 }; 514 }; 515}; 516 517&mdss_dsi0_out { 518 remote-endpoint = <&panel_in>; 519 data-lanes = <0 1 2 3>; 520}; 521 522&mdss_dsi0_phy { 523 vdds-supply = <&vreg_l1a_0p9>; 524 status = "okay"; 525}; 526 527&pm8998_gpios { 528 focus_n: focus-n-state { 529 pins = "gpio2"; 530 function = PMIC_GPIO_FUNC_NORMAL; 531 power-source = <0>; 532 bias-pull-up; 533 input-enable; 534 }; 535 536 vol_down_n: vol-down-n-state { 537 pins = "gpio5"; 538 function = PMIC_GPIO_FUNC_NORMAL; 539 power-source = <0>; 540 bias-pull-up; 541 input-enable; 542 }; 543 544 vol_up_n: vol-up-n-state { 545 pins = "gpio6"; 546 function = PMIC_GPIO_FUNC_NORMAL; 547 power-source = <0>; 548 bias-pull-up; 549 input-enable; 550 }; 551 552 snapshot_n: snapshot-n-state { 553 pins = "gpio7"; 554 function = PMIC_GPIO_FUNC_NORMAL; 555 power-source = <0>; 556 bias-pull-up; 557 input-enable; 558 }; 559}; 560 561&pmi8998_wled { 562 default-brightness = <800>; 563 qcom,switching-freq = <800>; 564 qcom,ovp-millivolt = <29600>; 565 qcom,current-boost-limit = <970>; 566 qcom,current-limit-microamp = <20000>; 567 qcom,enabled-strings = <0 1 2 3>; 568 status = "okay"; 569}; 570 571&qupv3_id_0 { 572 status = "okay"; 573}; 574 575&qupv3_id_1 { 576 status = "okay"; 577}; 578 579&sdhc_2 { 580 status = "okay"; 581 582 vmmc-supply = <&vreg_l21a_2p7>; 583 vqmmc-supply = <&vreg_l13a_1p8>; 584 cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>; 585 pinctrl-0 = <&sdc2_default_state>; 586 pinctrl-names = "default"; 587 bus-width = <4>; 588 no-sdio; 589 no-mmc; 590}; 591 592&tlmm { 593 gpio-reserved-ranges = <0 4>, <81 4>; 594 595 sdc2_default_state: sdc2-default-state { 596 clk-pins { 597 pins = "sdc2_clk"; 598 drive-strength = <16>; 599 bias-disable; 600 }; 601 602 cmd-pins { 603 pins = "sdc2_cmd"; 604 drive-strength = <10>; 605 bias-pull-up; 606 }; 607 608 data-pins { 609 pins = "sdc2_data"; 610 drive-strength = <10>; 611 bias-pull-up; 612 }; 613 }; 614 615 sde_dsi_active: sde-dsi-active-state { 616 pins = "gpio6"; 617 function = "gpio"; 618 drive-strength = <8>; 619 bias-disable; 620 }; 621 622 sde_dsi_sleep: sde-dsi-sleep-state { 623 pins = "gpio6"; 624 function = "gpio"; 625 drive-strength = <2>; 626 bias-pull-down; 627 }; 628 629 sde_te_active_sleep: sde-te-active-sleep-state { 630 pins = "gpio10"; 631 function = "mdp_vsync"; 632 drive-strength = <2>; 633 bias-pull-down; 634 }; 635 636 ts_default: ts-default-state { 637 reset-pins { 638 pins = "gpio99"; 639 function = "gpio"; 640 drive-strength = <2>; 641 bias-pull-up; 642 }; 643 644 int-pins { 645 pins = "gpio125"; 646 function = "gpio"; 647 drive-strength = <2>; 648 bias-pull-up; 649 }; 650 }; 651 652 ts_sleep: ts-sleep-state { 653 reset-pins { 654 pins = "gpio99"; 655 function = "gpio"; 656 drive-strength = <2>; 657 bias-pull-down; 658 }; 659 660 int-pins { 661 pins = "gpio125"; 662 function = "gpio"; 663 drive-strength = <2>; 664 bias-pull-down; 665 }; 666 }; 667}; 668 669&uart6 { 670 status = "okay"; 671}; 672 673&uart9 { 674 status = "okay"; 675}; 676 677/* BIG WARNING! DO NOT TOUCH UFS, YOUR DEVICE WILL DIE! */ 678&ufs_mem_hc { status = "disabled"; }; 679&ufs_mem_phy { status = "disabled"; }; 680 681&usb_1 { 682 status = "okay"; 683 684 qcom,select-utmi-as-pipe-clk; 685}; 686 687&usb_1_dwc3 { 688 dr_mode = "peripheral"; 689 690 maximum-speed = "high-speed"; 691 phys = <&usb_1_hsphy>; 692 phy-names = "usb2-phy"; 693}; 694 695&usb_1_hsphy { 696 status = "okay"; 697 698 vdd-supply = <&vreg_l1a_0p9>; 699 vdda-pll-supply = <&vreg_l12a_1p8>; 700 vdda-phy-dpdm-supply = <&vreg_l24a_3p1>; 701}; 702 703&venus { 704 firmware-name = "qcom/sdm845/Sony/tama/venus.mbn"; 705 status = "okay"; 706}; 707