1// SPDX-License-Identifier: GPL-2.0 2/* 3 * SDM845 MTP board device tree source 4 * 5 * Copyright (c) 2018, The Linux Foundation. All rights reserved. 6 */ 7 8/dts-v1/; 9 10#include <dt-bindings/regulator/qcom,rpmh-regulator.h> 11#include "sdm845.dtsi" 12#include "pm8998.dtsi" 13#include "pmi8998.dtsi" 14 15/ { 16 model = "Qualcomm Technologies, Inc. SDM845 MTP"; 17 compatible = "qcom,sdm845-mtp", "qcom,sdm845"; 18 chassis-type = "handset"; 19 20 aliases { 21 serial0 = &uart9; 22 }; 23 24 chosen { 25 stdout-path = "serial0:115200n8"; 26 }; 27 28 vph_pwr: vph-pwr-regulator { 29 compatible = "regulator-fixed"; 30 regulator-name = "vph_pwr"; 31 regulator-min-microvolt = <3700000>; 32 regulator-max-microvolt = <3700000>; 33 }; 34 35 /* 36 * Apparently RPMh does not provide support for PM8998 S4 because it 37 * is always-on; model it as a fixed regulator. 38 */ 39 vreg_s4a_1p8: pm8998-smps4 { 40 compatible = "regulator-fixed"; 41 regulator-name = "vreg_s4a_1p8"; 42 43 regulator-min-microvolt = <1800000>; 44 regulator-max-microvolt = <1800000>; 45 46 regulator-always-on; 47 regulator-boot-on; 48 49 vin-supply = <&vph_pwr>; 50 }; 51 52 thermal-zones { 53 xo_thermal: xo-thermal { 54 polling-delay-passive = <0>; 55 polling-delay = <0>; 56 57 thermal-sensors = <&pm8998_adc_tm 1>; 58 59 trips { 60 trip-point { 61 temperature = <125000>; 62 hysteresis = <10000>; 63 type = "passive"; 64 }; 65 }; 66 }; 67 68 msm_thermal: msm-thermal { 69 polling-delay-passive = <0>; 70 polling-delay = <0>; 71 72 thermal-sensors = <&pm8998_adc_tm 2>; 73 74 trips { 75 trip-point { 76 temperature = <125000>; 77 hysteresis = <10000>; 78 type = "passive"; 79 }; 80 }; 81 }; 82 83 pa_thermal: pa-thermal { 84 polling-delay-passive = <0>; 85 polling-delay = <0>; 86 87 thermal-sensors = <&pm8998_adc_tm 3>; 88 89 trips { 90 trip-point { 91 temperature = <125000>; 92 hysteresis = <10000>; 93 type = "passive"; 94 }; 95 }; 96 }; 97 98 quiet_thermal: quiet-thermal { 99 polling-delay-passive = <0>; 100 polling-delay = <0>; 101 102 thermal-sensors = <&pm8998_adc_tm 4>; 103 104 trips { 105 trip-point { 106 temperature = <125000>; 107 hysteresis = <10000>; 108 type = "passive"; 109 }; 110 }; 111 }; 112 }; 113}; 114 115&adsp_pas { 116 status = "okay"; 117 firmware-name = "qcom/sdm845/adsp.mbn"; 118}; 119 120&apps_rsc { 121 regulators-0 { 122 compatible = "qcom,pm8998-rpmh-regulators"; 123 qcom,pmic-id = "a"; 124 125 vdd-s1-supply = <&vph_pwr>; 126 vdd-s2-supply = <&vph_pwr>; 127 vdd-s3-supply = <&vph_pwr>; 128 vdd-s4-supply = <&vph_pwr>; 129 vdd-s5-supply = <&vph_pwr>; 130 vdd-s6-supply = <&vph_pwr>; 131 vdd-s7-supply = <&vph_pwr>; 132 vdd-s8-supply = <&vph_pwr>; 133 vdd-s9-supply = <&vph_pwr>; 134 vdd-s10-supply = <&vph_pwr>; 135 vdd-s11-supply = <&vph_pwr>; 136 vdd-s12-supply = <&vph_pwr>; 137 vdd-s13-supply = <&vph_pwr>; 138 vdd-l1-l27-supply = <&vreg_s7a_1p025>; 139 vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>; 140 vdd-l3-l11-supply = <&vreg_s7a_1p025>; 141 vdd-l4-l5-supply = <&vreg_s7a_1p025>; 142 vdd-l6-supply = <&vph_pwr>; 143 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>; 144 vdd-l9-supply = <&vreg_bob>; 145 vdd-l10-l23-l25-supply = <&vreg_bob>; 146 vdd-l13-l19-l21-supply = <&vreg_bob>; 147 vdd-l16-l28-supply = <&vreg_bob>; 148 vdd-l18-l22-supply = <&vreg_bob>; 149 vdd-l20-l24-supply = <&vreg_bob>; 150 vdd-l26-supply = <&vreg_s3a_1p35>; 151 vin-lvs-1-2-supply = <&vreg_s4a_1p8>; 152 153 vreg_s2a_1p125: smps2 { 154 regulator-min-microvolt = <1100000>; 155 regulator-max-microvolt = <1100000>; 156 }; 157 158 vreg_s3a_1p35: smps3 { 159 regulator-min-microvolt = <1352000>; 160 regulator-max-microvolt = <1352000>; 161 }; 162 163 vreg_s5a_2p04: smps5 { 164 regulator-min-microvolt = <1904000>; 165 regulator-max-microvolt = <2040000>; 166 }; 167 168 vreg_s7a_1p025: smps7 { 169 regulator-min-microvolt = <900000>; 170 regulator-max-microvolt = <1028000>; 171 }; 172 173 vdd_qusb_hs0: 174 vdda_hp_pcie_core: 175 vdda_mipi_csi0_0p9: 176 vdda_mipi_csi1_0p9: 177 vdda_mipi_csi2_0p9: 178 vdda_mipi_dsi0_pll: 179 vdda_mipi_dsi1_pll: 180 vdda_qlink_lv: 181 vdda_qlink_lv_ck: 182 vdda_qrefs_0p875: 183 vdda_pcie_core: 184 vdda_pll_cc_ebi01: 185 vdda_pll_cc_ebi23: 186 vdda_sp_sensor: 187 vdda_ufs1_core: 188 vdda_ufs2_core: 189 vdda_usb1_ss_core: 190 vdda_usb2_ss_core: 191 vreg_l1a_0p875: ldo1 { 192 regulator-min-microvolt = <880000>; 193 regulator-max-microvolt = <880000>; 194 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 195 }; 196 197 vddpx_10: 198 vreg_l2a_1p2: ldo2 { 199 regulator-min-microvolt = <1200000>; 200 regulator-max-microvolt = <1200000>; 201 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 202 regulator-always-on; 203 }; 204 205 vreg_l3a_1p0: ldo3 { 206 regulator-min-microvolt = <1000000>; 207 regulator-max-microvolt = <1000000>; 208 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 209 }; 210 211 vdd_wcss_cx: 212 vdd_wcss_mx: 213 vdda_wcss_pll: 214 vreg_l5a_0p8: ldo5 { 215 regulator-min-microvolt = <800000>; 216 regulator-max-microvolt = <800000>; 217 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 218 }; 219 220 vddpx_13: 221 vreg_l6a_1p8: ldo6 { 222 regulator-min-microvolt = <1856000>; 223 regulator-max-microvolt = <1856000>; 224 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 225 }; 226 227 vreg_l7a_1p8: ldo7 { 228 regulator-min-microvolt = <1800000>; 229 regulator-max-microvolt = <1800000>; 230 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 231 }; 232 233 vreg_l8a_1p2: ldo8 { 234 regulator-min-microvolt = <1200000>; 235 regulator-max-microvolt = <1248000>; 236 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 237 }; 238 239 vreg_l9a_1p8: ldo9 { 240 regulator-min-microvolt = <1704000>; 241 regulator-max-microvolt = <2928000>; 242 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 243 }; 244 245 vreg_l10a_1p8: ldo10 { 246 regulator-min-microvolt = <1704000>; 247 regulator-max-microvolt = <2928000>; 248 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 249 }; 250 251 vreg_l11a_1p0: ldo11 { 252 regulator-min-microvolt = <1000000>; 253 regulator-max-microvolt = <1048000>; 254 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 255 }; 256 257 vdd_qfprom: 258 vdd_qfprom_sp: 259 vdda_apc1_cs_1p8: 260 vdda_gfx_cs_1p8: 261 vdda_qrefs_1p8: 262 vdda_qusb_hs0_1p8: 263 vddpx_11: 264 vreg_l12a_1p8: ldo12 { 265 regulator-min-microvolt = <1800000>; 266 regulator-max-microvolt = <1800000>; 267 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 268 }; 269 270 vddpx_2: 271 vreg_l13a_2p95: ldo13 { 272 regulator-min-microvolt = <1800000>; 273 regulator-max-microvolt = <2960000>; 274 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 275 }; 276 277 vreg_l14a_1p88: ldo14 { 278 regulator-min-microvolt = <1800000>; 279 regulator-max-microvolt = <1800000>; 280 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 281 }; 282 283 vreg_l15a_1p8: ldo15 { 284 regulator-min-microvolt = <1800000>; 285 regulator-max-microvolt = <1800000>; 286 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 287 }; 288 289 vreg_l16a_2p7: ldo16 { 290 regulator-min-microvolt = <2704000>; 291 regulator-max-microvolt = <2704000>; 292 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 293 }; 294 295 vreg_l17a_1p3: ldo17 { 296 regulator-min-microvolt = <1304000>; 297 regulator-max-microvolt = <1304000>; 298 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 299 }; 300 301 vreg_l18a_2p7: ldo18 { 302 regulator-min-microvolt = <2704000>; 303 regulator-max-microvolt = <2960000>; 304 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 305 }; 306 307 vreg_l19a_3p0: ldo19 { 308 regulator-min-microvolt = <2856000>; 309 regulator-max-microvolt = <3104000>; 310 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 311 }; 312 313 vreg_l20a_2p95: ldo20 { 314 regulator-min-microvolt = <2704000>; 315 regulator-max-microvolt = <2960000>; 316 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 317 }; 318 319 vreg_l21a_2p95: ldo21 { 320 regulator-min-microvolt = <2704000>; 321 regulator-max-microvolt = <2960000>; 322 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 323 }; 324 325 vreg_l22a_2p85: ldo22 { 326 regulator-min-microvolt = <2864000>; 327 regulator-max-microvolt = <3312000>; 328 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 329 }; 330 331 vreg_l23a_3p3: ldo23 { 332 regulator-min-microvolt = <3000000>; 333 regulator-max-microvolt = <3312000>; 334 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 335 }; 336 337 vdda_qusb_hs0_3p1: 338 vreg_l24a_3p075: ldo24 { 339 regulator-min-microvolt = <3088000>; 340 regulator-max-microvolt = <3088000>; 341 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 342 }; 343 344 vreg_l25a_3p3: ldo25 { 345 regulator-min-microvolt = <3300000>; 346 regulator-max-microvolt = <3312000>; 347 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 348 }; 349 350 vdda_hp_pcie_1p2: 351 vdda_hv_ebi0: 352 vdda_hv_ebi1: 353 vdda_hv_ebi2: 354 vdda_hv_ebi3: 355 vdda_mipi_csi_1p25: 356 vdda_mipi_dsi0_1p2: 357 vdda_mipi_dsi1_1p2: 358 vdda_pcie_1p2: 359 vdda_ufs1_1p2: 360 vdda_ufs2_1p2: 361 vdda_usb1_ss_1p2: 362 vdda_usb2_ss_1p2: 363 vreg_l26a_1p2: ldo26 { 364 regulator-min-microvolt = <1200000>; 365 regulator-max-microvolt = <1200000>; 366 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 367 }; 368 369 vreg_l28a_3p0: ldo28 { 370 regulator-min-microvolt = <2856000>; 371 regulator-max-microvolt = <3008000>; 372 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 373 }; 374 375 vreg_lvs1a_1p8: lvs1 { 376 regulator-min-microvolt = <1800000>; 377 regulator-max-microvolt = <1800000>; 378 }; 379 380 vreg_lvs2a_1p8: lvs2 { 381 regulator-min-microvolt = <1800000>; 382 regulator-max-microvolt = <1800000>; 383 }; 384 }; 385 386 regulators-1 { 387 compatible = "qcom,pmi8998-rpmh-regulators"; 388 qcom,pmic-id = "b"; 389 390 vdd-bob-supply = <&vph_pwr>; 391 392 vreg_bob: bob { 393 regulator-min-microvolt = <3312000>; 394 regulator-max-microvolt = <3600000>; 395 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; 396 regulator-allow-bypass; 397 }; 398 }; 399 400 regulators-2 { 401 compatible = "qcom,pm8005-rpmh-regulators"; 402 qcom,pmic-id = "c"; 403 404 vdd-s1-supply = <&vph_pwr>; 405 vdd-s2-supply = <&vph_pwr>; 406 vdd-s3-supply = <&vph_pwr>; 407 vdd-s4-supply = <&vph_pwr>; 408 409 vreg_s3c_0p6: smps3 { 410 regulator-min-microvolt = <600000>; 411 regulator-max-microvolt = <600000>; 412 }; 413 }; 414}; 415 416&cdsp_pas { 417 status = "okay"; 418 firmware-name = "qcom/sdm845/cdsp.mbn"; 419}; 420 421&gcc { 422 protected-clocks = <GCC_QSPI_CORE_CLK>, 423 <GCC_QSPI_CORE_CLK_SRC>, 424 <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, 425 <GCC_LPASS_Q6_AXI_CLK>, 426 <GCC_LPASS_SWAY_CLK>; 427}; 428 429&gmu { 430 status = "okay"; 431}; 432 433&gpu { 434 status = "okay"; 435 436 zap-shader { 437 memory-region = <&gpu_mem>; 438 firmware-name = "qcom/sdm845/a630_zap.mbn"; 439 }; 440}; 441 442&i2c10 { 443 status = "okay"; 444 clock-frequency = <400000>; 445}; 446 447&ipa { 448 qcom,gsi-loader = "self"; 449 memory-region = <&ipa_fw_mem>; 450 status = "okay"; 451}; 452 453&mdss { 454 status = "okay"; 455}; 456 457&mdss_dsi0 { 458 status = "okay"; 459 vdda-supply = <&vdda_mipi_dsi0_1p2>; 460 461 qcom,dual-dsi-mode; 462 qcom,master-dsi; 463 464 ports { 465 port@1 { 466 endpoint { 467 remote-endpoint = <&truly_in_0>; 468 data-lanes = <0 1 2 3>; 469 }; 470 }; 471 }; 472 473 panel@0 { 474 compatible = "truly,nt35597-2K-display"; 475 reg = <0>; 476 vdda-supply = <&vreg_l14a_1p88>; 477 478 reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; 479 mode-gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>; 480 481 ports { 482 #address-cells = <1>; 483 #size-cells = <0>; 484 485 port@0 { 486 reg = <0>; 487 truly_in_0: endpoint { 488 remote-endpoint = <&mdss_dsi0_out>; 489 }; 490 }; 491 492 port@1 { 493 reg = <1>; 494 truly_in_1: endpoint { 495 remote-endpoint = <&mdss_dsi1_out>; 496 }; 497 }; 498 }; 499 }; 500}; 501 502&mdss_dsi0_phy { 503 status = "okay"; 504 vdds-supply = <&vdda_mipi_dsi0_pll>; 505}; 506 507&mdss_dsi1 { 508 status = "okay"; 509 vdda-supply = <&vdda_mipi_dsi1_1p2>; 510 511 qcom,dual-dsi-mode; 512 513 /* DSI1 is slave, so use DSI0 clocks */ 514 assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>; 515 516 ports { 517 port@1 { 518 endpoint { 519 remote-endpoint = <&truly_in_1>; 520 data-lanes = <0 1 2 3>; 521 }; 522 }; 523 }; 524}; 525 526&mdss_dsi1_phy { 527 status = "okay"; 528 vdds-supply = <&vdda_mipi_dsi1_pll>; 529}; 530 531&mss_pil { 532 status = "okay"; 533 firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn"; 534}; 535 536&pcie0 { 537 perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>; 538 539 pinctrl-0 = <&pcie0_default_state>; 540 pinctrl-names = "default"; 541 542 status = "okay"; 543}; 544 545&pcie0_phy { 546 vdda-phy-supply = <&vreg_l1a_0p875>; 547 vdda-pll-supply = <&vreg_l26a_1p2>; 548 549 status = "okay"; 550}; 551 552&pcie1 { 553 perst-gpios = <&tlmm 102 GPIO_ACTIVE_LOW>; 554 555 pinctrl-names = "default"; 556 pinctrl-0 = <&pcie1_default_state>; 557 558 status = "okay"; 559}; 560 561&pcie1_phy { 562 status = "okay"; 563 564 vdda-phy-supply = <&vreg_l1a_0p875>; 565 vdda-pll-supply = <&vreg_l26a_1p2>; 566}; 567 568&pm8998_adc { 569 channel@4c { 570 reg = <ADC5_XO_THERM_100K_PU>; 571 label = "xo_therm"; 572 qcom,ratiometric; 573 qcom,hw-settle-time = <200>; 574 }; 575 576 channel@4d { 577 reg = <ADC5_AMUX_THM1_100K_PU>; 578 label = "msm_therm"; 579 qcom,ratiometric; 580 qcom,hw-settle-time = <200>; 581 }; 582 583 channel@4f { 584 reg = <ADC5_AMUX_THM3_100K_PU>; 585 label = "pa_therm1"; 586 qcom,ratiometric; 587 qcom,hw-settle-time = <200>; 588 }; 589 590 channel@51 { 591 reg = <ADC5_AMUX_THM5_100K_PU>; 592 label = "quiet_therm"; 593 qcom,ratiometric; 594 qcom,hw-settle-time = <200>; 595 }; 596 597 channel@83 { 598 reg = <ADC5_VPH_PWR>; 599 label = "vph_pwr"; 600 qcom,ratiometric; 601 qcom,hw-settle-time = <200>; 602 }; 603 604 channel@85 { 605 reg = <ADC5_VCOIN>; 606 label = "vcoin"; 607 qcom,ratiometric; 608 qcom,hw-settle-time = <200>; 609 }; 610}; 611 612&pm8998_adc_tm { 613 status = "okay"; 614 615 xo-thermistor@1 { 616 reg = <1>; 617 io-channels = <&pm8998_adc ADC5_XO_THERM_100K_PU>; 618 qcom,ratiometric; 619 qcom,hw-settle-time-us = <200>; 620 }; 621 622 msm-thermistor@2 { 623 reg = <2>; 624 io-channels = <&pm8998_adc ADC5_AMUX_THM1_100K_PU>; 625 qcom,ratiometric; 626 qcom,hw-settle-time-us = <200>; 627 }; 628 629 pa-thermistor@3 { 630 reg = <3>; 631 io-channels = <&pm8998_adc ADC5_AMUX_THM3_100K_PU>; 632 qcom,ratiometric; 633 qcom,hw-settle-time-us = <200>; 634 }; 635 636 quiet-thermistor@4 { 637 reg = <4>; 638 io-channels = <&pm8998_adc ADC5_AMUX_THM5_100K_PU>; 639 qcom,ratiometric; 640 qcom,hw-settle-time-us = <200>; 641 }; 642}; 643 644&pm8998_resin { 645 linux,code = <KEY_VOLUMEDOWN>; 646 status = "okay"; 647}; 648 649&qupv3_id_1 { 650 status = "okay"; 651}; 652 653&sdhc_2 { 654 status = "okay"; 655 656 pinctrl-names = "default"; 657 pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_card_det_n>; 658 659 vmmc-supply = <&vreg_l21a_2p95>; 660 vqmmc-supply = <&vddpx_2>; 661 662 cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>; 663}; 664 665&tlmm { 666 pcie0_default_state: pcie0-default-state { 667 clkreq-pins { 668 pins = "gpio36"; 669 function = "pci_e0"; 670 bias-pull-up; 671 }; 672 673 perst-n-pins { 674 pins = "gpio35"; 675 function = "gpio"; 676 drive-strength = <2>; 677 bias-pull-down; 678 }; 679 680 wake-n-pins { 681 pins = "gpio37"; 682 function = "gpio"; 683 drive-strength = <2>; 684 bias-pull-up; 685 }; 686 }; 687 688 pcie1_default_state: pcie1-default-state { 689 clkreq-pins { 690 pins = "gpio103"; 691 function = "pci_e1"; 692 bias-pull-up; 693 }; 694 695 perst-n-pins { 696 pins = "gpio102"; 697 function = "gpio"; 698 drive-strength = <16>; 699 bias-pull-down; 700 }; 701 702 wake-n-pins { 703 pins = "gpio104"; 704 function = "gpio"; 705 drive-strength = <2>; 706 bias-pull-up; 707 }; 708 }; 709}; 710 711&uart9 { 712 status = "okay"; 713}; 714 715&ufs_mem_hc { 716 status = "okay"; 717 718 reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; 719 720 vcc-supply = <&vreg_l20a_2p95>; 721 vcc-max-microamp = <600000>; 722}; 723 724&ufs_mem_phy { 725 status = "okay"; 726 727 vdda-phy-supply = <&vdda_ufs1_core>; 728 vdda-pll-supply = <&vdda_ufs1_1p2>; 729}; 730 731&usb_1 { 732 status = "okay"; 733}; 734 735&usb_1_dwc3 { 736 /* Until we have Type C hooked up we'll force this as peripheral. */ 737 dr_mode = "peripheral"; 738}; 739 740&usb_1_hsphy { 741 status = "okay"; 742 743 vdd-supply = <&vdda_usb1_ss_core>; 744 vdda-pll-supply = <&vdda_qusb_hs0_1p8>; 745 vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; 746 747 qcom,imp-res-offset-value = <8>; 748 qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; 749 qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; 750 qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; 751}; 752 753&usb_1_qmpphy { 754 status = "okay"; 755 756 vdda-phy-supply = <&vdda_usb1_ss_1p2>; 757 vdda-pll-supply = <&vdda_usb1_ss_core>; 758}; 759 760&usb_2 { 761 status = "okay"; 762}; 763 764&usb_2_dwc3 { 765 /* 766 * Though the USB block on SDM845 can support host, there's no vbus 767 * signal for this port on MTP. Thus (unless you have a non-compliant 768 * hub that works without vbus) the only sensible thing is to force 769 * peripheral mode. 770 */ 771 dr_mode = "peripheral"; 772}; 773 774&usb_2_hsphy { 775 status = "okay"; 776 777 vdd-supply = <&vdda_usb2_ss_core>; 778 vdda-pll-supply = <&vdda_qusb_hs0_1p8>; 779 vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; 780 781 qcom,imp-res-offset-value = <8>; 782 qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>; 783}; 784 785&usb_2_qmpphy { 786 status = "okay"; 787 788 vdda-phy-supply = <&vdda_usb2_ss_1p2>; 789 vdda-pll-supply = <&vdda_usb2_ss_core>; 790}; 791 792&venus { 793 status = "okay"; 794}; 795 796&wifi { 797 status = "okay"; 798 vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; 799 vdd-1.8-xo-supply = <&vreg_l7a_1p8>; 800 vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; 801 vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; 802 803 qcom,snoc-host-cap-8bit-quirk; 804 qcom,ath10k-calibration-variant = "Qualcomm_sdm845mtp"; 805}; 806 807/* PINCTRL - additions to nodes defined in sdm845.dtsi */ 808 809&qup_i2c10_default { 810 drive-strength = <2>; 811 bias-disable; 812}; 813 814&qup_uart9_rx { 815 drive-strength = <2>; 816 bias-pull-up; 817}; 818 819&qup_uart9_tx { 820 drive-strength = <2>; 821 bias-disable; 822}; 823 824&tlmm { 825 gpio-reserved-ranges = <0 4>, <81 4>; 826 827 sdc2_clk: sdc2-clk-state { 828 pins = "sdc2_clk"; 829 bias-disable; 830 831 /* 832 * It seems that mmc_test reports errors if drive 833 * strength is not 16 on clk, cmd, and data pins. 834 */ 835 drive-strength = <16>; 836 }; 837 838 sdc2_cmd: sdc2-cmd-state { 839 pins = "sdc2_cmd"; 840 bias-pull-up; 841 drive-strength = <16>; 842 }; 843 844 sdc2_data: sdc2-data-state { 845 pins = "sdc2_data"; 846 bias-pull-up; 847 drive-strength = <16>; 848 }; 849 850 sd_card_det_n: sd-card-det-n-state { 851 pins = "gpio126"; 852 function = "gpio"; 853 bias-pull-up; 854 }; 855}; 856