1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. 4 * Copyright (c) 2020-2023, Linaro Limited 5 */ 6 7/dts-v1/; 8 9#include <dt-bindings/firmware/qcom,scm.h> 10#include <dt-bindings/gpio/gpio.h> 11#include <dt-bindings/input/gpio-keys.h> 12#include <dt-bindings/input/input.h> 13#include <dt-bindings/regulator/qcom,rpmh-regulator.h> 14#include "sc8180x.dtsi" 15#include "sc8180x-pmics.dtsi" 16 17/ { 18 model = "Qualcomm SC8180x Primus"; 19 compatible = "qcom,sc8180x-primus", "qcom,sc8180x"; 20 21 aliases { 22 serial0 = &uart12; 23 serial1 = &uart13; 24 }; 25 26 backlight: backlight { 27 compatible = "pwm-backlight"; 28 pwms = <&pmc8180c_lpg 4 1000000>; 29 enable-gpios = <&pmc8180c_gpios 8 GPIO_ACTIVE_HIGH>; 30 31 pinctrl-names = "default"; 32 pinctrl-0 = <&bl_pwm_default>; 33 }; 34 35 chosen { 36 stdout-path = "serial0:115200n8"; 37 }; 38 39 gpio-keys { 40 compatible = "gpio-keys"; 41 42 pinctrl-names = "default"; 43 pinctrl-0 = <&hall_int_active_state>; 44 45 lid-switch { 46 gpios = <&tlmm 121 GPIO_ACTIVE_LOW>; 47 linux,input-type = <EV_SW>; 48 linux,code = <SW_LID>; 49 wakeup-source; 50 wakeup-event-action = <EV_ACT_DEASSERTED>; 51 }; 52 }; 53 54 pmic-glink { 55 compatible = "qcom,sc8180x-pmic-glink", "qcom,pmic-glink"; 56 57 #address-cells = <1>; 58 #size-cells = <0>; 59 60 connector@0 { 61 compatible = "usb-c-connector"; 62 reg = <0>; 63 power-role = "dual"; 64 data-role = "dual"; 65 66 ports { 67 #address-cells = <1>; 68 #size-cells = <0>; 69 70 port@0 { 71 reg = <0>; 72 73 pmic_glink_con0_hs: endpoint { 74 remote-endpoint = <&usb_prim_dwc3_hs>; 75 }; 76 }; 77 78 port@1 { 79 reg = <1>; 80 81 pmic_glink_con0_ss: endpoint { 82 remote-endpoint = <&usb_prim_qmpphy_out>; 83 }; 84 }; 85 86 port@2 { 87 reg = <2>; 88 89 pmic_glink_con0_sbu: endpoint { 90 remote-endpoint = <&usbprim_sbu_mux>; 91 }; 92 }; 93 }; 94 }; 95 96 connector@1 { 97 compatible = "usb-c-connector"; 98 reg = <1>; 99 power-role = "dual"; 100 data-role = "dual"; 101 102 ports { 103 #address-cells = <1>; 104 #size-cells = <0>; 105 port@0 { 106 reg = <0>; 107 108 pmic_glink_con1_hs: endpoint { 109 remote-endpoint = <&usb_sec_dwc3_hs>; 110 }; 111 }; 112 113 port@1 { 114 reg = <1>; 115 116 pmic_glink_con1_ss: endpoint { 117 remote-endpoint = <&usb_sec_qmpphy_out>; 118 }; 119 }; 120 121 port@2 { 122 reg = <2>; 123 124 pmic_glink_con1_sbu: endpoint { 125 remote-endpoint = <&usbsec_sbu_mux>; 126 }; 127 }; 128 }; 129 }; 130 }; 131 132 reserved-memory { 133 rmtfs_mem: rmtfs-region@85500000 { 134 compatible = "qcom,rmtfs-mem"; 135 reg = <0x0 0x85500000 0x0 0x200000>; 136 no-map; 137 138 qcom,client-id = <1>; 139 qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>; 140 }; 141 142 wlan_mem: wlan-region@8bc00000 { 143 reg = <0x0 0x8bc00000 0x0 0x180000>; 144 no-map; 145 }; 146 147 adsp_mem: adsp-region@96e00000 { 148 reg = <0x0 0x96e00000 0x0 0x1c00000>; 149 no-map; 150 }; 151 152 mpss_mem: mpss-region@8d800000 { 153 reg = <0x0 0x8d800000 0x0 0x9600000>; 154 no-map; 155 }; 156 157 gpu_mem: gpu-region@98a00000 { 158 reg = <0x0 0x98a00000 0x0 0x2000>; 159 no-map; 160 }; 161 162 reserved-region@9a500000 { 163 reg = <0x0 0x9a500000 0x0 0x600000>; 164 no-map; 165 }; 166 }; 167 168 vreg_nvme_0p9: nvme-0p9-regulator { 169 compatible = "regulator-fixed"; 170 regulator-name = "vreg_nvme_0p9"; 171 172 regulator-min-microvolt = <900000>; 173 regulator-max-microvolt = <900000>; 174 175 regulator-always-on; 176 }; 177 178 vreg_nvme_3p3: nvme-3p3-regulator { 179 compatible = "regulator-fixed"; 180 regulator-name = "vreg_nvme_3p3"; 181 182 regulator-min-microvolt = <3300000>; 183 regulator-max-microvolt = <3300000>; 184 185 gpio = <&pmc8180c_gpios 11 0>; 186 enable-active-high; 187 188 regulator-always-on; 189 }; 190 191 vdd_kb_tp_3v3: vdd-kb-tp-3v3-regulator { 192 compatible = "regulator-fixed"; 193 regulator-name = "vdd_kb_tp_3v3"; 194 regulator-min-microvolt = <3300000>; 195 regulator-max-microvolt = <3300000>; 196 197 gpio = <&tlmm 4 GPIO_ACTIVE_HIGH>; 198 enable-active-high; 199 200 regulator-always-on; 201 202 pinctrl-names = "default"; 203 pinctrl-0 = <&kb_tp_3v3_en_active_state>; 204 }; 205 206 vph_pwr: vph-pwr-regulator { 207 compatible = "regulator-fixed"; 208 regulator-name = "vph_pwr"; 209 regulator-min-microvolt = <3700000>; 210 regulator-max-microvolt = <3700000>; 211 }; 212 213 vreg_s4a_1p8: pm8150-s4 { 214 compatible = "regulator-fixed"; 215 regulator-name = "vreg_s4a_1p8"; 216 217 regulator-min-microvolt = <1800000>; 218 regulator-max-microvolt = <1800000>; 219 220 regulator-always-on; 221 regulator-boot-on; 222 223 vin-supply = <&vph_pwr>; 224 }; 225 226 vreg_usb2_host_en: regulator-usb2-host-en { 227 compatible = "regulator-fixed"; 228 regulator-name = "usb2_host_en"; 229 230 regulator-min-microvolt = <5000000>; 231 regulator-max-microvolt = <5000000>; 232 233 gpio = <&pmc8180_1_gpios 9 GPIO_ACTIVE_HIGH>; 234 enable-active-high; 235 236 regulator-always-on; 237 }; 238 239 vreg_usb3_host_en: regulator-usb3-host-en { 240 compatible = "regulator-fixed"; 241 regulator-name = "usb3_host_en"; 242 243 regulator-min-microvolt = <5000000>; 244 regulator-max-microvolt = <5000000>; 245 246 gpio = <&pmc8180_2_gpios 9 GPIO_ACTIVE_HIGH>; 247 enable-active-high; 248 249 regulator-always-on; 250 }; 251 252 usbprim-sbu-mux { 253 compatible = "pericom,pi3usb102", "gpio-sbu-mux"; 254 255 enable-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; 256 select-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>; 257 258 pinctrl-names = "default"; 259 pinctrl-0 = <&usbprim_sbu_default>; 260 261 mode-switch; 262 orientation-switch; 263 264 port { 265 usbprim_sbu_mux: endpoint { 266 remote-endpoint = <&pmic_glink_con0_sbu>; 267 }; 268 }; 269 }; 270 271 usbsec-sbu-mux { 272 compatible = "pericom,pi3usb102", "gpio-sbu-mux"; 273 274 enable-gpios = <&tlmm 188 GPIO_ACTIVE_LOW>; 275 select-gpios = <&tlmm 187 GPIO_ACTIVE_HIGH>; 276 277 pinctrl-names = "default"; 278 pinctrl-0 = <&usbsec_sbu_default>; 279 280 mode-switch; 281 orientation-switch; 282 283 port { 284 usbsec_sbu_mux: endpoint { 285 remote-endpoint = <&pmic_glink_con1_sbu>; 286 }; 287 }; 288 }; 289}; 290 291&apps_rsc { 292 regulators-0 { 293 compatible = "qcom,pmc8180-rpmh-regulators"; 294 qcom,pmic-id = "a"; 295 296 vdd-s5-supply = <&vph_pwr>; 297 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p0>; 298 299 vreg_s5a_2p0: smps5 { 300 regulator-min-microvolt = <2040000>; 301 regulator-max-microvolt = <2100000>; 302 }; 303 304 vreg_l7a_1p8: ldo7 { 305 regulator-min-microvolt = <1800000>; 306 regulator-max-microvolt = <1800000>; 307 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 308 }; 309 310 vreg_l9a_1p3: ldo9 { 311 regulator-min-microvolt = <1296000>; 312 regulator-max-microvolt = <1304000>; 313 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 314 }; 315 316 vreg_l12a_1p8: ldo12 { 317 regulator-min-microvolt = <1800000>; 318 regulator-max-microvolt = <1800000>; 319 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 320 }; 321 }; 322 323 regulators-1 { 324 compatible = "qcom,pmc8180c-rpmh-regulators"; 325 qcom,pmic-id = "c"; 326 327 vdd-s6-supply = <&vph_pwr>; 328 vdd-s8-supply = <&vph_pwr>; 329 vdd-l2-l3-supply = <&vreg_s6c_1p35>; 330 vdd-bob-supply = <&vph_pwr>; 331 332 vreg_s6c_1p35: smps6 { 333 regulator-min-microvolt = <1350000>; 334 regulator-max-microvolt = <1372000>; 335 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 336 }; 337 338 vreg_s8c_1p8: smps8 { 339 regulator-min-microvolt = <1800000>; 340 regulator-max-microvolt = <1800000>; 341 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 342 regulator-always-on; 343 }; 344 345 vreg_l3c_1p2: ldo3 { 346 regulator-min-microvolt = <1200000>; 347 regulator-max-microvolt = <1200000>; 348 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 349 }; 350 351 vreg_l4c_3p3: ldo4 { 352 regulator-min-microvolt = <3008000>; 353 regulator-max-microvolt = <3008000>; 354 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 355 }; 356 357 vreg_l10c_3p3: ldo10 { 358 regulator-min-microvolt = <3000000>; 359 regulator-max-microvolt = <3312000>; 360 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 361 }; 362 363 vreg_l11c_3p3: ldo11 { 364 regulator-min-microvolt = <3296000>; 365 regulator-max-microvolt = <3304000>; 366 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 367 }; 368 369 vreg_bob: bob { 370 regulator-min-microvolt = <3296000>; 371 regulator-max-microvolt = <3350000>; 372 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 373 }; 374 }; 375 376 regulators-2 { 377 compatible = "qcom,pmc8180-rpmh-regulators"; 378 qcom,pmic-id = "e"; 379 380 vdd-s4-supply = <&vph_pwr>; 381 vdd-s5-supply = <&vph_pwr>; 382 vdd-l2-l10-supply = <&vreg_bob>; 383 vdd-l3-l4-l5-l18-supply = <&vreg_s4e_0p98>; 384 vdd-l7-l12-l14-l15-supply = <&vreg_s5e_2p05>; 385 vdd-l13-l16-l17-supply = <&vreg_bob>; 386 387 vreg_s4e_0p98: smps4 { 388 regulator-min-microvolt = <992000>; 389 regulator-max-microvolt = <992000>; 390 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 391 }; 392 393 vreg_s5e_2p05: smps5 { 394 regulator-min-microvolt = <2040000>; 395 regulator-max-microvolt = <2040000>; 396 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 397 }; 398 399 vreg_l1e_0p75: ldo1 { 400 regulator-min-microvolt = <752000>; 401 regulator-max-microvolt = <752000>; 402 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 403 }; 404 405 vreg_l5e_0p88: ldo5 { 406 regulator-min-microvolt = <880000>; 407 regulator-max-microvolt = <880000>; 408 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 409 }; 410 411 vreg_l7e_1p8: ldo7 { 412 regulator-min-microvolt = <1800000>; 413 regulator-max-microvolt = <1800000>; 414 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 415 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 416 RPMH_REGULATOR_MODE_HPM>; 417 regulator-allow-set-load; 418 }; 419 420 vreg_l10e_2p9: ldo10 { 421 regulator-min-microvolt = <2904000>; 422 regulator-max-microvolt = <2904000>; 423 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 424 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 425 RPMH_REGULATOR_MODE_HPM>; 426 regulator-allow-set-load; 427 }; 428 429 vreg_l12e: ldo12 { 430 regulator-min-microvolt = <1800000>; 431 regulator-max-microvolt = <1800000>; 432 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 433 }; 434 435 vreg_l16e_3p0: ldo16 { 436 regulator-min-microvolt = <3072000>; 437 regulator-max-microvolt = <3072000>; 438 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 439 }; 440 }; 441}; 442 443&gpu { 444 status = "okay"; 445 446 zap-shader { 447 memory-region = <&gpu_mem>; 448 firmware-name = "qcom/sc8180x/qcdxkmsuc8180.mbn"; 449 }; 450}; 451 452&i2c1 { 453 clock-frequency = <100000>; 454 455 pinctrl-names = "default"; 456 pinctrl-0 = <&ts_i2c_active_state>; 457 458 status = "okay"; 459 460 touchscreen@10 { 461 compatible = "hid-over-i2c"; 462 reg = <0x10>; 463 hid-descr-addr = <0x1>; 464 465 vdd-supply = <&vreg_l4c_3p3>; 466 vddl-supply = <&vreg_l12e>; 467 468 post-power-on-delay-ms = <20>; 469 470 interrupts-extended = <&tlmm 122 IRQ_TYPE_LEVEL_LOW>; 471 472 pinctrl-names = "default"; 473 pinctrl-0 = <&ts_active_state>; 474 }; 475}; 476 477&i2c7 { 478 clock-frequency = <100000>; 479 480 pinctrl-names = "default"; 481 pinctrl-0 = <&aux_i2c_active_state>; 482 483 status = "okay"; 484 485 touchpad@15 { 486 compatible = "hid-over-i2c"; 487 reg = <0x15>; 488 hid-descr-addr = <0x1>; 489 490 interrupts-extended = <&tlmm 24 IRQ_TYPE_LEVEL_LOW>; 491 492 pinctrl-names = "default"; 493 pinctrl-0 = <&tp_int_active_state>; 494 495 vdd-supply = <&vdd_kb_tp_3v3>; 496 }; 497 498 keyboard@3a { 499 compatible = "hid-over-i2c"; 500 reg = <0x3a>; 501 hid-descr-addr = <0x1>; 502 interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_LOW>; 503 504 pinctrl-names = "default"; 505 pinctrl-0 = <&kb_int_active_state>; 506 507 vdd-supply = <&vdd_kb_tp_3v3>; 508 }; 509}; 510 511&mdss { 512 status = "okay"; 513}; 514 515&mdss_dp0 { 516 status = "okay"; 517}; 518 519&mdss_dp0_out { 520 data-lanes = <0 1>; 521 remote-endpoint = <&usb_prim_qmpphy_dp_in>; 522}; 523 524&mdss_dp1 { 525 status = "okay"; 526}; 527 528&mdss_dp1_out { 529 data-lanes = <0 1>; 530 remote-endpoint = <&usb_sec_qmpphy_dp_in>; 531}; 532 533&mdss_edp { 534 data-lanes = <0 1 2 3>; 535 536 pinctrl-names = "default"; 537 pinctrl-0 = <&edp_hpd_active>; 538 539 status = "okay"; 540 541 aux-bus { 542 panel { 543 compatible = "edp-panel"; 544 545 backlight = <&backlight>; 546 547 port { 548 auo_b133han05_in: endpoint { 549 remote-endpoint = <&mdss_edp_out>; 550 }; 551 }; 552 }; 553 }; 554 555 ports { 556 port@1 { 557 reg = <1>; 558 mdss_edp_out: endpoint { 559 remote-endpoint = <&auo_b133han05_in>; 560 }; 561 }; 562 }; 563}; 564 565&pcie1 { 566 perst-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>; 567 wake-gpios = <&tlmm 177 GPIO_ACTIVE_HIGH>; 568 pinctrl-names = "default"; 569 pinctrl-0 = <&pcie2_default_state>; 570 571 status = "okay"; 572}; 573 574&pcie1_phy { 575 vdda-phy-supply = <&vreg_l5e_0p88>; 576 vdda-pll-supply = <&vreg_l3c_1p2>; 577 578 status = "okay"; 579}; 580 581&pmc8180_pwrkey { 582 status = "okay"; 583}; 584 585&pmc8180c_lpg { 586 status = "okay"; 587}; 588 589&qupv3_id_0 { 590 status = "okay"; 591}; 592 593&qupv3_id_1 { 594 status = "okay"; 595}; 596 597&qupv3_id_2 { 598 status = "okay"; 599}; 600 601&remoteproc_adsp { 602 memory-region = <&adsp_mem>; 603 firmware-name = "qcom/sc8180x/qcadsp8180.mbn"; 604 605 status = "okay"; 606}; 607 608&remoteproc_mpss { 609 memory-region = <&mpss_mem>; 610 firmware-name = "qcom/sc8180x/qcmpss8180.mbn"; 611 612 status = "okay"; 613}; 614 615&uart12 { 616 compatible = "qcom,geni-debug-uart"; 617 status = "okay"; 618}; 619 620&uart13 { 621 pinctrl-names = "default"; 622 pinctrl-0 = <&uart13_state>; 623 624 status = "okay"; 625 626 bluetooth { 627 compatible = "qcom,wcn3998-bt"; 628 629 vddio-supply = <&vreg_s4a_1p8>; 630 vddxo-supply = <&vreg_l7a_1p8>; 631 vddrf-supply = <&vreg_l9a_1p3>; 632 vddch0-supply = <&vreg_l11c_3p3>; 633 max-speed = <3200000>; 634 }; 635}; 636 637&ufs_mem_hc { 638 reset-gpios = <&tlmm 190 GPIO_ACTIVE_LOW>; 639 640 vcc-supply = <&vreg_l10e_2p9>; 641 vcc-max-microamp = <155000>; 642 643 vccq2-supply = <&vreg_l7e_1p8>; 644 vccq2-max-microamp = <425000>; 645 646 status = "okay"; 647}; 648 649&ufs_mem_phy { 650 vdda-phy-supply = <&vreg_l5e_0p88>; 651 vdda-pll-supply = <&vreg_l3c_1p2>; 652 653 status = "okay"; 654}; 655 656&usb_mp { 657 status = "okay"; 658}; 659 660&usb_mp_hsphy0 { 661 vdda-pll-supply = <&vreg_l5e_0p88>; 662 vdda18-supply = <&vreg_l12a_1p8>; 663 vdda33-supply = <&vreg_l16e_3p0>; 664 665 status = "okay"; 666}; 667 668&usb_mp_hsphy1 { 669 vdda-pll-supply = <&vreg_l5e_0p88>; 670 vdda18-supply = <&vreg_l12a_1p8>; 671 vdda33-supply = <&vreg_l16e_3p0>; 672 673 status = "okay"; 674}; 675 676&usb_mp_qmpphy0 { 677 vdda-phy-supply = <&vreg_l3c_1p2>; 678 vdda-pll-supply = <&vreg_l5e_0p88>; 679 680 status = "okay"; 681}; 682 683&usb_mp_qmpphy1 { 684 vdda-phy-supply = <&vreg_l3c_1p2>; 685 vdda-pll-supply = <&vreg_l5e_0p88>; 686 687 status = "okay"; 688}; 689 690&usb_prim_hsphy { 691 vdda-pll-supply = <&vreg_l5e_0p88>; 692 vdda18-supply = <&vreg_l12a_1p8>; 693 vdda33-supply = <&vreg_l16e_3p0>; 694 695 status = "okay"; 696}; 697 698&usb_prim_qmpphy { 699 vdda-phy-supply = <&vreg_l3c_1p2>; 700 vdda-pll-supply = <&vreg_l5e_0p88>; 701 702 orientation-switch; 703 704 status = "okay"; 705}; 706 707&usb_prim { 708 status = "okay"; 709}; 710 711&usb_prim_dwc3 { 712 dr_mode = "host"; 713}; 714 715&usb_prim_dwc3_hs { 716 remote-endpoint = <&pmic_glink_con0_hs>; 717}; 718 719&usb_prim_qmpphy_dp_in { 720 remote-endpoint = <&mdss_dp0_out>; 721}; 722 723&usb_prim_qmpphy_out { 724 remote-endpoint = <&pmic_glink_con0_ss>; 725}; 726 727&usb_sec_hsphy { 728 vdda-pll-supply = <&vreg_l5e_0p88>; 729 vdda18-supply = <&vreg_l12a_1p8>; 730 vdda33-supply = <&vreg_l16e_3p0>; 731 732 status = "okay"; 733}; 734 735&usb_sec_qmpphy { 736 vdda-phy-supply = <&vreg_l3c_1p2>; 737 vdda-pll-supply = <&vreg_l5e_0p88>; 738 739 orientation-switch; 740 741 status = "okay"; 742}; 743 744&usb_sec_qmpphy_dp_in { 745 remote-endpoint = <&mdss_dp1_out>; 746}; 747 748&usb_sec_qmpphy_out { 749 remote-endpoint = <&pmic_glink_con1_ss>; 750}; 751 752&usb_sec { 753 status = "okay"; 754}; 755 756&usb_sec_dwc3 { 757 dr_mode = "host"; 758}; 759 760&usb_sec_dwc3_hs { 761 remote-endpoint = <&pmic_glink_con1_hs>; 762}; 763 764&wifi { 765 memory-region = <&wlan_mem>; 766 767 vdd-0.8-cx-mx-supply = <&vreg_l1e_0p75>; 768 vdd-1.8-xo-supply = <&vreg_l7a_1p8>; 769 vdd-1.3-rfa-supply = <&vreg_l9a_1p3>; 770 vdd-3.3-ch0-supply = <&vreg_l11c_3p3>; 771 vdd-3.3-ch1-supply = <&vreg_l10c_3p3>; 772 773 status = "okay"; 774}; 775 776&xo_board_clk { 777 clock-frequency = <38400000>; 778}; 779 780/* PINCTRL */ 781 782&pmc8180c_gpios { 783 bl_pwm_default: bl-pwm-default-state { 784 en-pins { 785 pins = "gpio8"; 786 function = "normal"; 787 }; 788 789 pwm-pins { 790 pins = "gpio10"; 791 function = "func1"; 792 }; 793 }; 794}; 795 796&tlmm { 797 gpio-reserved-ranges = <0 4>, <47 4>, <126 4>; 798 799 aux_i2c_active_state: aux-i2c-active-state { 800 pins = "gpio98", "gpio99"; 801 function = "qup7"; 802 803 bias-disable; 804 drive-strength = <16>; 805 }; 806 807 edp_hpd_active: epd-hpd-active-state { 808 pins = "gpio10"; 809 function = "edp_hot"; 810 }; 811 812 hall_int_active_state: hall-int-active-state { 813 pins = "gpio121"; 814 function = "gpio"; 815 816 bias-disable; 817 }; 818 819 kb_int_active_state: kb-int-active-state { 820 int-n-pins { 821 pins = "gpio37"; 822 function = "gpio"; 823 824 bias-pull-up; 825 }; 826 827 kp-disable-pins { 828 pins = "gpio135"; 829 function = "gpio"; 830 831 output-high; 832 }; 833 }; 834 835 kb_tp_3v3_en_active_state: kb-tp-3v3-en-active-state { 836 pins = "gpio4"; 837 function = "gpio"; 838 839 bias-disable; 840 }; 841 842 pcie2_default_state: pcie2-default-state { 843 clkreq-pins { 844 pins = "gpio176"; 845 function = "pci_e2"; 846 bias-pull-up; 847 }; 848 849 reset-n-pins { 850 pins = "gpio175"; 851 function = "gpio"; 852 853 drive-strength = <2>; 854 output-low; 855 bias-pull-down; 856 }; 857 858 wake-n-pins { 859 pins = "gpio177"; 860 function = "gpio"; 861 862 drive-strength = <2>; 863 bias-pull-up; 864 }; 865 }; 866 867 usbprim_sbu_default: usbprim-sbu-state { 868 oe-n-pins { 869 pins = "gpio152"; 870 function = "gpio"; 871 bias-disable; 872 drive-strength = <16>; 873 output-high; 874 }; 875 876 sel-pins { 877 pins = "gpio100"; 878 function = "gpio"; 879 bias-disable; 880 drive-strength = <16>; 881 }; 882 }; 883 884 usbsec_sbu_default: usbsec-sbu-state { 885 oe-n-pins { 886 pins = "gpio188"; 887 function = "gpio"; 888 bias-disable; 889 drive-strength = <16>; 890 output-high; 891 }; 892 893 sel-pins { 894 pins = "gpio187"; 895 function = "gpio"; 896 bias-disable; 897 drive-strength = <16>; 898 }; 899 }; 900 901 tp_int_active_state: tp-int-active-state { 902 tp-int-pins { 903 pins = "gpio24"; 904 function = "gpio"; 905 906 bias-disable; 907 }; 908 909 tp-close-n-pins { 910 pins = "gpio116"; 911 function = "gpio"; 912 913 bias-disable; 914 }; 915 }; 916 917 ts_active_state: ts-active-state { 918 int-n-pins { 919 pins = "gpio122"; 920 function = "gpio"; 921 922 bias-disable; 923 }; 924 925 reset-n-pins { 926 pins = "gpio54"; 927 function = "gpio"; 928 929 output-high; 930 }; 931 }; 932 933 ts_i2c_active_state: ts-i2c-active-state { 934 pins = "gpio114", "gpio115"; 935 function = "qup1"; 936 937 /* External pull up */ 938 bias-disable; 939 drive-strength = <2>; 940 }; 941 942 uart13_state: uart13-state { 943 cts-pins { 944 pins = "gpio43"; 945 function = "qup13"; 946 bias-pull-down; 947 }; 948 949 rts-tx-pins { 950 pins = "gpio44", "gpio45"; 951 function = "qup13"; 952 drive-strength = <2>; 953 bias-disable; 954 }; 955 956 rx-pins { 957 pins = "gpio46"; 958 function = "qup13"; 959 bias-pull-up; 960 }; 961 }; 962}; 963