1// SPDX-License-Identifier: (GPL-2.0+ OR MIT) 2/* 3 * Google Trogdor board device tree source 4 * 5 * Copyright 2020 Google LLC. 6 */ 7 8/dts-v1/; 9 10#include "sc7180.dtsi" 11 12ap_ec_spi: &spi6 {}; 13ap_h1_spi: &spi0 {}; 14 15#include "sc7180-trogdor.dtsi" 16 17/ { 18 model = "Google Trogdor (rev1+)"; 19 compatible = "google,trogdor", "qcom,sc7180"; 20 21 panel: panel { 22 compatible = "auo,b116xa01"; 23 power-supply = <&pp3300_dx_edp>; 24 backlight = <&backlight>; 25 hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>; 26 27 ports { 28 port { 29 panel_in_edp: endpoint { 30 remote-endpoint = <&sn65dsi86_out>; 31 }; 32 }; 33 }; 34 }; 35}; 36 37ap_ts_pen_1v8: &i2c4 { 38 status = "okay"; 39 clock-frequency = <400000>; 40 41 ap_ts: touchscreen@10 { 42 compatible = "elan,ekth3500"; 43 reg = <0x10>; 44 pinctrl-names = "default"; 45 pinctrl-0 = <&ts_int_l>, <&ts_reset_l>; 46 47 interrupt-parent = <&tlmm>; 48 interrupts = <9 IRQ_TYPE_LEVEL_LOW>; 49 50 vcc33-supply = <&pp3300_ts>; 51 52 reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>; 53 }; 54}; 55 56&pp3300_hub { 57 /* pp3300_l7c is used to power the USB hub */ 58 /delete-property/regulator-always-on; 59 /delete-property/regulator-boot-on; 60}; 61 62&pp3300_l7c { 63 regulator-always-on; 64 regulator-boot-on; 65}; 66 67&sdhc_2 { 68 status = "okay"; 69}; 70 71/* PINCTRL - board-specific pinctrl */ 72 73&tlmm { 74 gpio-line-names = "ESIM_MISO", 75 "ESIM_MOSI", 76 "ESIM_CLK", 77 "ESIM_CS_L", 78 "FP_TO_AP_IRQ_L", 79 "FP_RST_L", 80 "AP_TP_I2C_SDA", 81 "AP_TP_I2C_SCL", 82 "TS_RESET_L", 83 "TS_INT_L", 84 "FPMCU_BOOT0", 85 "EDP_BRIJ_IRQ", 86 "AP_EDP_BKLTEN", 87 "", 88 "", 89 "EDP_BRIJ_I2C_SDA", 90 "EDP_BRIJ_I2C_SCL", 91 "HUB_RST_L", 92 "PEN_RST_ODL", 93 "AP_RAM_ID1", 94 "AP_RAM_ID2", 95 "PEN_IRQ_L", 96 "FPMCU_SEL", 97 "AMP_EN", 98 "P_SENSOR_INT_L", 99 "AP_SAR_SENSOR_SDA", 100 "AP_SAR_SENSOR_SCL", 101 "", 102 "HP_IRQ", 103 "AP_RAM_ID0", 104 "EN_PP3300_DX_EDP", 105 "AP_BRD_ID2", 106 "BRIJ_SUSPEND", 107 "AP_BRD_ID0", 108 "AP_H1_SPI_MISO", 109 "AP_H1_SPI_MOSI", 110 "AP_H1_SPI_CLK", 111 "AP_H1_SPI_CS_L", 112 "", 113 "", 114 "", 115 "", 116 "H1_AP_INT_ODL", 117 "", 118 "UART_AP_TX_DBG_RX", 119 "UART_DBG_TX_AP_RX", 120 "HP_I2C_SDA", 121 "HP_I2C_SCL", 122 "FORCED_USB_BOOT", 123 "", 124 "", 125 "AMP_DIN", 126 "PEN_PDCT_L", 127 "HP_BCLK", 128 "HP_LRCLK", 129 "HP_DOUT", 130 "HP_DIN", 131 "HP_MCLK", 132 "TRACKPAD_INT_1V8_ODL", 133 "AP_EC_SPI_MISO", 134 "AP_EC_SPI_MOSI", 135 "AP_EC_SPI_CLK", 136 "AP_EC_SPI_CS_L", 137 "AP_SPI_CLK", 138 "AP_SPI_MOSI", 139 "AP_SPI_MISO", 140 /* 141 * AP_FLASH_WP_L is crossystem ABI. Schematics 142 * call it BIOS_FLASH_WP_L. 143 */ 144 "AP_FLASH_WP_L", 145 "DBG_SPI_HOLD_L", 146 "AP_SPI_CS0_L", 147 "SD_CD_ODL", 148 "", 149 "", 150 "", 151 "", 152 "", 153 "UIM2_DATA", 154 "UIM2_CLK", 155 "UIM2_RST", 156 "UIM2_PRESENT", 157 "UIM1_DATA", 158 "UIM1_CLK", 159 "UIM1_RST", 160 "", 161 "EN_PP3300_CODEC", 162 "EN_PP3300_HUB", 163 "", 164 "AP_SPI_FP_MISO", 165 "AP_SPI_FP_MOSI", 166 "AP_SPI_FP_CLK", 167 "AP_SPI_FP_CS_L", 168 "AP_SKU_ID1", 169 "AP_RST_REQ", 170 "", 171 "AP_BRD_ID1", 172 "AP_EC_INT_L", 173 "", 174 "", 175 "", 176 "", 177 "", 178 "", 179 "", 180 "", 181 "", 182 "EDP_BRIJ_EN", 183 "AP_SKU_ID0", 184 "", 185 "", 186 "", 187 "", 188 "", 189 "", 190 "", 191 "", 192 "", 193 "AP_TS_PEN_I2C_SDA", 194 "AP_TS_PEN_I2C_SCL", 195 "DP_HOT_PLUG_DET", 196 "EC_IN_RW_ODL"; 197}; 198