1// SPDX-License-Identifier: (GPL-2.0+ OR MIT) 2/* 3 * Google Lazor board device tree source 4 * 5 * Copyright 2020 Google LLC. 6 */ 7 8/* This file must be included after sc7180-trogdor.dtsi */ 9#include <arm/cros-ec-keyboard.dtsi> 10 11&ap_sar_sensor { 12 semtech,cs0-ground; 13 semtech,combined-sensors = <3>; 14 semtech,resolution = "fine"; 15 semtech,startup-sensor = <0>; 16 semtech,proxraw-strength = <8>; 17 semtech,avg-pos-strength = <64>; 18}; 19 20&ap_tp_i2c { 21 status = "okay"; 22}; 23 24/* 25 * Lazor is stuffed with a 47k NTC as charger thermistor which currently is 26 * not supported by the PM6150 ADC driver. Disable the charger thermal zone 27 * to avoid using bogus temperature values. 28 */ 29&charger_thermal { 30 status = "disabled"; 31}; 32 33ap_ts_pen_1v8: &i2c4 { 34 status = "okay"; 35 clock-frequency = <400000>; 36 37 ap_ts: touchscreen@10 { 38 compatible = "hid-over-i2c"; 39 reg = <0x10>; 40 pinctrl-names = "default"; 41 pinctrl-0 = <&ts_int_l>, <&ts_reset_l>; 42 43 interrupt-parent = <&tlmm>; 44 interrupts = <9 IRQ_TYPE_LEVEL_LOW>; 45 46 panel = <&panel>; 47 post-power-on-delay-ms = <20>; 48 hid-descr-addr = <0x0001>; 49 50 vdd-supply = <&pp3300_ts>; 51 }; 52}; 53 54&panel { 55 compatible = "boe,nv133fhm-n62"; 56}; 57 58&pm6150_adc { 59 /delete-node/ channel@4f; 60}; 61 62&pm6150_adc_tm { 63 status = "disabled"; 64 65 /delete-node/ charger-thermistor@0; 66}; 67 68&trackpad { 69 interrupts = <58 IRQ_TYPE_EDGE_FALLING>; 70}; 71 72&wifi { 73 qcom,ath10k-calibration-variant = "GO_LAZOR"; 74}; 75 76/* PINCTRL - modifications to sc7180-trogdor.dtsi */ 77 78&trackpad_int_1v8_odl { 79 pins = "gpio58"; 80}; 81 82&ts_reset_l { 83 /* This pin is not connected on -rev0, pull up to park. */ 84 /delete-property/bias-disable; 85 bias-pull-up; 86}; 87 88/* PINCTRL - board-specific pinctrl */ 89 90&tlmm { 91 gpio-line-names = "ESIM_MISO", 92 "ESIM_MOSI", 93 "ESIM_CLK", 94 "ESIM_CS_L", 95 "", 96 "", 97 "AP_TP_I2C_SDA", 98 "AP_TP_I2C_SCL", 99 "TS_RESET_L", 100 "TS_INT_L", 101 "", 102 "EDP_BRIJ_IRQ", 103 "AP_EDP_BKLTEN", 104 "AP_RAM_ID2", 105 "", 106 "EDP_BRIJ_I2C_SDA", 107 "EDP_BRIJ_I2C_SCL", 108 "HUB_RST_L", 109 "", 110 "AP_RAM_ID1", 111 "AP_SKU_ID2", 112 "", 113 "", 114 "AMP_EN", 115 "P_SENSOR_INT_L", 116 "AP_SAR_SENSOR_SDA", 117 "AP_SAR_SENSOR_SCL", 118 "", 119 "HP_IRQ", 120 "AP_RAM_ID0", 121 "EN_PP3300_DX_EDP", 122 "AP_BRD_ID2", 123 "BRIJ_SUSPEND", 124 "AP_BRD_ID0", 125 "AP_H1_SPI_MISO", 126 "AP_H1_SPI_MOSI", 127 "AP_H1_SPI_CLK", 128 "AP_H1_SPI_CS_L", 129 "", 130 "", 131 "", 132 "", 133 "H1_AP_INT_ODL", 134 "", 135 "UART_AP_TX_DBG_RX", 136 "UART_DBG_TX_AP_RX", 137 "HP_I2C_SDA", 138 "HP_I2C_SCL", 139 "FORCED_USB_BOOT", 140 "", 141 "", 142 "AMP_DIN", 143 "", 144 "HP_BCLK", 145 "HP_LRCLK", 146 "HP_DOUT", 147 "HP_DIN", 148 "HP_MCLK", 149 "TRACKPAD_INT_1V8_ODL", 150 "AP_EC_SPI_MISO", 151 "AP_EC_SPI_MOSI", 152 "AP_EC_SPI_CLK", 153 "AP_EC_SPI_CS_L", 154 "AP_SPI_CLK", 155 "AP_SPI_MOSI", 156 "AP_SPI_MISO", 157 /* 158 * AP_FLASH_WP_L is crossystem ABI. Schematics 159 * call it BIOS_FLASH_WP_L. 160 */ 161 "AP_FLASH_WP_L", 162 "DBG_SPI_HOLD_L", 163 "AP_SPI_CS0_L", 164 "", 165 "", 166 "", 167 "", 168 "", 169 "", 170 "UIM2_DATA", 171 "UIM2_CLK", 172 "UIM2_RST", 173 "UIM2_PRESENT", 174 "UIM1_DATA", 175 "UIM1_CLK", 176 "UIM1_RST", 177 "", 178 "EN_PP3300_CODEC", 179 "EN_PP3300_HUB", 180 "", 181 "", 182 "", 183 "", 184 "", 185 "AP_SKU_ID1", 186 "AP_RST_REQ", 187 "", 188 "AP_BRD_ID1", 189 "AP_EC_INT_L", 190 "", 191 "", 192 "", 193 "", 194 "", 195 "", 196 "", 197 "", 198 "", 199 "EDP_BRIJ_EN", 200 "AP_SKU_ID0", 201 "", 202 "", 203 "", 204 "", 205 "", 206 "", 207 "", 208 "", 209 "", 210 "AP_TS_PEN_I2C_SDA", 211 "AP_TS_PEN_I2C_SCL", 212 "DP_HOT_PLUG_DET", 213 "EC_IN_RW_ODL"; 214}; 215