1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2021, Linaro Limited 4 */ 5 6#include <dt-bindings/input/input.h> 7#include <dt-bindings/interrupt-controller/irq.h> 8#include <dt-bindings/spmi/spmi.h> 9#include <dt-bindings/iio/qcom,spmi-vadc.h> 10 11/ { 12 thermal-zones { 13 pmm8155au-1-thermal { 14 polling-delay-passive = <100>; 15 polling-delay = <0>; 16 17 thermal-sensors = <&pmm8155au_1_temp>; 18 19 trips { 20 trip0 { 21 temperature = <95000>; 22 hysteresis = <0>; 23 type = "passive"; 24 }; 25 26 trip1 { 27 temperature = <115000>; 28 hysteresis = <0>; 29 type = "hot"; 30 }; 31 32 trip2 { 33 temperature = <145000>; 34 hysteresis = <0>; 35 type = "critical"; 36 }; 37 }; 38 }; 39 }; 40}; 41 42&spmi_bus { 43 pmic@0 { 44 compatible = "qcom,pmm8155au", "qcom,spmi-pmic"; 45 reg = <0x0 SPMI_USID>; 46 #address-cells = <1>; 47 #size-cells = <0>; 48 49 pon: power-on@800 { 50 compatible = "qcom,pm8916-pon"; 51 reg = <0x0800>; 52 pwrkey { 53 compatible = "qcom,pm8941-pwrkey"; 54 interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; 55 debounce = <15625>; 56 bias-pull-up; 57 linux,code = <KEY_POWER>; 58 59 status = "disabled"; 60 }; 61 }; 62 63 pmm8155au_1_temp: temp-alarm@2400 { 64 compatible = "qcom,spmi-temp-alarm"; 65 reg = <0x2400>; 66 interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; 67 io-channels = <&pmm8155au_1_adc ADC5_DIE_TEMP>; 68 io-channel-names = "thermal"; 69 #thermal-sensor-cells = <0>; 70 }; 71 72 pmm8155au_1_adc: adc@3100 { 73 compatible = "qcom,spmi-adc5"; 74 reg = <0x3100>; 75 #address-cells = <1>; 76 #size-cells = <0>; 77 #io-channel-cells = <1>; 78 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 79 80 ref-gnd@0 { 81 reg = <ADC5_REF_GND>; 82 qcom,pre-scaling = <1 1>; 83 label = "ref_gnd"; 84 }; 85 86 vref-1p25@1 { 87 reg = <ADC5_1P25VREF>; 88 qcom,pre-scaling = <1 1>; 89 label = "vref_1p25"; 90 }; 91 92 die-temp@6 { 93 reg = <ADC5_DIE_TEMP>; 94 qcom,pre-scaling = <1 1>; 95 label = "die_temp"; 96 }; 97 }; 98 99 pmm8155au_1_adc_tm: adc-tm@3500 { 100 compatible = "qcom,spmi-adc-tm5"; 101 reg = <0x3500>; 102 interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; 103 #thermal-sensor-cells = <1>; 104 #address-cells = <1>; 105 #size-cells = <0>; 106 status = "disabled"; 107 }; 108 109 pmm8155au_1_rtc: rtc@6000 { 110 compatible = "qcom,pm8941-rtc"; 111 reg = <0x6000>; 112 reg-names = "rtc", "alarm"; 113 interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; 114 115 status = "disabled"; 116 }; 117 118 pmm8155au_1_gpios: gpio@c000 { 119 compatible = "qcom,pmm8155au-gpio"; 120 reg = <0xc000>; 121 gpio-controller; 122 #gpio-cells = <2>; 123 gpio-ranges = <&pmm8155au_1_gpios 0 0 10>; 124 interrupt-controller; 125 #interrupt-cells = <2>; 126 }; 127 }; 128 129 pmic@1 { 130 compatible = "qcom,pmm8155au", "qcom,spmi-pmic"; 131 reg = <0x1 SPMI_USID>; 132 #address-cells = <1>; 133 #size-cells = <0>; 134 }; 135}; 136