1// SPDX-License-Identifier: GPL-2.0 2#include <dt-bindings/iio/qcom,spmi-vadc.h> 3#include <dt-bindings/input/linux-event-codes.h> 4#include <dt-bindings/interrupt-controller/irq.h> 5#include <dt-bindings/spmi/spmi.h> 6 7/ { 8 thermal-zones { 9 pm8994-thermal { 10 polling-delay-passive = <250>; 11 12 thermal-sensors = <&pm8994_temp>; 13 14 trips { 15 pm8994_alert0: pm8994-alert0 { 16 temperature = <95000>; 17 hysteresis = <2000>; 18 type = "passive"; 19 }; 20 pm8994_crit: pm8994-crit { 21 temperature = <125000>; 22 hysteresis = <2000>; 23 type = "critical"; 24 }; 25 }; 26 }; 27 }; 28}; 29 30&spmi_bus { 31 32 pmic@0 { 33 compatible = "qcom,pm8994", "qcom,spmi-pmic"; 34 reg = <0x0 SPMI_USID>; 35 #address-cells = <1>; 36 #size-cells = <0>; 37 38 rtc@6000 { 39 compatible = "qcom,pm8941-rtc"; 40 reg = <0x6000>, <0x6100>; 41 reg-names = "rtc", "alarm"; 42 interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; 43 }; 44 45 pm8994_pon: pon@800 { 46 compatible = "qcom,pm8916-pon"; 47 reg = <0x800>; 48 mode-bootloader = <0x2>; 49 mode-recovery = <0x1>; 50 51 pwrkey { 52 compatible = "qcom,pm8941-pwrkey"; 53 interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; 54 debounce = <15625>; 55 bias-pull-up; 56 linux,code = <KEY_POWER>; 57 }; 58 59 pm8994_resin: resin { 60 compatible = "qcom,pm8941-resin"; 61 interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; 62 debounce = <15625>; 63 bias-pull-up; 64 status = "disabled"; 65 }; 66 }; 67 68 pm8994_temp: temp-alarm@2400 { 69 compatible = "qcom,spmi-temp-alarm"; 70 reg = <0x2400>; 71 interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; 72 io-channels = <&pm8994_vadc VADC_DIE_TEMP>; 73 io-channel-names = "thermal"; 74 #thermal-sensor-cells = <0>; 75 }; 76 77 pm8994_vadc: adc@3100 { 78 compatible = "qcom,spmi-vadc"; 79 reg = <0x3100>; 80 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 81 #address-cells = <1>; 82 #size-cells = <0>; 83 #io-channel-cells = <1>; 84 85 channel@7 { 86 reg = <VADC_VSYS>; 87 qcom,pre-scaling = <1 3>; 88 label = "vph_pwr"; 89 }; 90 channel@8 { 91 reg = <VADC_DIE_TEMP>; 92 label = "die_temp"; 93 }; 94 channel@9 { 95 reg = <VADC_REF_625MV>; 96 label = "ref_625mv"; 97 }; 98 channel@a { 99 reg = <VADC_REF_1250MV>; 100 label = "ref_1250mv"; 101 }; 102 channel@e { 103 reg = <VADC_GND_REF>; 104 }; 105 channel@f { 106 reg = <VADC_VDD_VADC>; 107 }; 108 }; 109 110 pm8994_gpios: gpio@c000 { 111 compatible = "qcom,pm8994-gpio", "qcom,spmi-gpio"; 112 reg = <0xc000>; 113 gpio-controller; 114 gpio-ranges = <&pm8994_gpios 0 0 22>; 115 #gpio-cells = <2>; 116 interrupt-controller; 117 #interrupt-cells = <2>; 118 }; 119 120 pm8994_mpps: mpps@a000 { 121 compatible = "qcom,pm8994-mpp", "qcom,spmi-mpp"; 122 reg = <0xa000>; 123 gpio-controller; 124 #gpio-cells = <2>; 125 gpio-ranges = <&pm8994_mpps 0 0 8>; 126 interrupt-controller; 127 #interrupt-cells = <2>; 128 }; 129 }; 130 131 pmic@1 { 132 compatible = "qcom,pm8994", "qcom,spmi-pmic"; 133 reg = <0x1 SPMI_USID>; 134 #address-cells = <1>; 135 #size-cells = <0>; 136 137 pm8994_lpg: pwm { 138 compatible = "qcom,pm8994-lpg"; 139 140 #address-cells = <1>; 141 #size-cells = <0>; 142 #pwm-cells = <2>; 143 144 status = "disabled"; 145 }; 146 147 pm8994_spmi_regulators: regulators { 148 compatible = "qcom,pm8994-regulators"; 149 }; 150 }; 151}; 152