1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. 4 * Copyright (c) 2019, Linaro Limited 5 */ 6 7#include <dt-bindings/iio/qcom,spmi-vadc.h> 8#include <dt-bindings/interrupt-controller/irq.h> 9#include <dt-bindings/spmi/spmi.h> 10 11/ { 12 thermal-zones { 13 pm8150l-thermal { 14 polling-delay-passive = <100>; 15 16 thermal-sensors = <&pm8150l_temp>; 17 18 trips { 19 trip0 { 20 temperature = <95000>; 21 hysteresis = <0>; 22 type = "passive"; 23 }; 24 25 trip1 { 26 temperature = <115000>; 27 hysteresis = <0>; 28 type = "hot"; 29 }; 30 31 trip2 { 32 temperature = <145000>; 33 hysteresis = <0>; 34 type = "critical"; 35 }; 36 }; 37 }; 38 }; 39}; 40 41&spmi_bus { 42 pmic@4 { 43 compatible = "qcom,pm8150l", "qcom,spmi-pmic"; 44 reg = <0x4 SPMI_USID>; 45 #address-cells = <1>; 46 #size-cells = <0>; 47 48 pon@800 { 49 compatible = "qcom,pm8916-pon"; 50 reg = <0x0800>; 51 52 status = "disabled"; 53 }; 54 55 pm8150l_temp: temp-alarm@2400 { 56 compatible = "qcom,spmi-temp-alarm"; 57 reg = <0x2400>; 58 interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; 59 io-channels = <&pm8150l_adc ADC5_DIE_TEMP>; 60 io-channel-names = "thermal"; 61 #thermal-sensor-cells = <0>; 62 }; 63 64 pm8150l_adc: adc@3100 { 65 compatible = "qcom,spmi-adc5"; 66 reg = <0x3100>; 67 #address-cells = <1>; 68 #size-cells = <0>; 69 #io-channel-cells = <1>; 70 interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 71 72 channel@0 { 73 reg = <ADC5_REF_GND>; 74 qcom,pre-scaling = <1 1>; 75 label = "ref_gnd"; 76 }; 77 78 channel@1 { 79 reg = <ADC5_1P25VREF>; 80 qcom,pre-scaling = <1 1>; 81 label = "vref_1p25"; 82 }; 83 84 channel@6 { 85 reg = <ADC5_DIE_TEMP>; 86 qcom,pre-scaling = <1 1>; 87 label = "die_temp"; 88 }; 89 }; 90 91 pm8150l_adc_tm: adc-tm@3500 { 92 compatible = "qcom,spmi-adc-tm5"; 93 reg = <0x3500>; 94 interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>; 95 #thermal-sensor-cells = <1>; 96 #address-cells = <1>; 97 #size-cells = <0>; 98 status = "disabled"; 99 }; 100 101 pm8150l_gpios: gpio@c000 { 102 compatible = "qcom,pm8150l-gpio", "qcom,spmi-gpio"; 103 reg = <0xc000>; 104 gpio-controller; 105 gpio-ranges = <&pm8150l_gpios 0 0 12>; 106 #gpio-cells = <2>; 107 interrupt-controller; 108 #interrupt-cells = <2>; 109 }; 110 }; 111 112 pmic@5 { 113 compatible = "qcom,pm8150l", "qcom,spmi-pmic"; 114 reg = <0x5 SPMI_USID>; 115 #address-cells = <1>; 116 #size-cells = <0>; 117 118 pm8150l_flash: led-controller@d300 { 119 compatible = "qcom,pm8150l-flash-led", "qcom,spmi-flash-led"; 120 reg = <0xd300>; 121 status = "disabled"; 122 }; 123 124 pm8150l_lpg: pwm { 125 compatible = "qcom,pm8150l-lpg"; 126 127 #address-cells = <1>; 128 #size-cells = <0>; 129 #pwm-cells = <2>; 130 131 status = "disabled"; 132 }; 133 134 pm8150l_wled: leds@d800 { 135 compatible = "qcom,pm8150l-wled"; 136 reg = <0xd800>, <0xd900>; 137 interrupts = <0x5 0xd8 0x1 IRQ_TYPE_EDGE_RISING>, 138 <0x5 0xd8 0x2 IRQ_TYPE_EDGE_RISING>; 139 interrupt-names = "ovp", "short"; 140 label = "backlight"; 141 142 status = "disabled"; 143 }; 144 }; 145}; 146