1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. 4 * Copyright (c) 2019, Linaro Limited 5 */ 6 7#include <dt-bindings/iio/qcom,spmi-vadc.h> 8#include <dt-bindings/interrupt-controller/irq.h> 9#include <dt-bindings/spmi/spmi.h> 10 11/ { 12 thermal-zones { 13 pm8150l-thermal { 14 polling-delay-passive = <100>; 15 polling-delay = <0>; 16 17 thermal-sensors = <&pm8150l_temp>; 18 19 trips { 20 trip0 { 21 temperature = <95000>; 22 hysteresis = <0>; 23 type = "passive"; 24 }; 25 26 trip1 { 27 temperature = <115000>; 28 hysteresis = <0>; 29 type = "hot"; 30 }; 31 32 trip2 { 33 temperature = <145000>; 34 hysteresis = <0>; 35 type = "critical"; 36 }; 37 }; 38 }; 39 }; 40}; 41 42&spmi_bus { 43 pmic@4 { 44 compatible = "qcom,pm8150l", "qcom,spmi-pmic"; 45 reg = <0x4 SPMI_USID>; 46 #address-cells = <1>; 47 #size-cells = <0>; 48 49 pon@800 { 50 compatible = "qcom,pm8916-pon"; 51 reg = <0x0800>; 52 53 status = "disabled"; 54 }; 55 56 pm8150l_temp: temp-alarm@2400 { 57 compatible = "qcom,spmi-temp-alarm"; 58 reg = <0x2400>; 59 interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; 60 io-channels = <&pm8150l_adc ADC5_DIE_TEMP>; 61 io-channel-names = "thermal"; 62 #thermal-sensor-cells = <0>; 63 }; 64 65 pm8150l_adc: adc@3100 { 66 compatible = "qcom,spmi-adc5"; 67 reg = <0x3100>; 68 #address-cells = <1>; 69 #size-cells = <0>; 70 #io-channel-cells = <1>; 71 interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 72 73 channel@0 { 74 reg = <ADC5_REF_GND>; 75 qcom,pre-scaling = <1 1>; 76 label = "ref_gnd"; 77 }; 78 79 channel@1 { 80 reg = <ADC5_1P25VREF>; 81 qcom,pre-scaling = <1 1>; 82 label = "vref_1p25"; 83 }; 84 85 channel@6 { 86 reg = <ADC5_DIE_TEMP>; 87 qcom,pre-scaling = <1 1>; 88 label = "die_temp"; 89 }; 90 }; 91 92 pm8150l_adc_tm: adc-tm@3500 { 93 compatible = "qcom,spmi-adc-tm5"; 94 reg = <0x3500>; 95 interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>; 96 #thermal-sensor-cells = <1>; 97 #address-cells = <1>; 98 #size-cells = <0>; 99 status = "disabled"; 100 }; 101 102 pm8150l_gpios: gpio@c000 { 103 compatible = "qcom,pm8150l-gpio", "qcom,spmi-gpio"; 104 reg = <0xc000>; 105 gpio-controller; 106 gpio-ranges = <&pm8150l_gpios 0 0 12>; 107 #gpio-cells = <2>; 108 interrupt-controller; 109 #interrupt-cells = <2>; 110 }; 111 }; 112 113 pmic@5 { 114 compatible = "qcom,pm8150l", "qcom,spmi-pmic"; 115 reg = <0x5 SPMI_USID>; 116 #address-cells = <1>; 117 #size-cells = <0>; 118 119 pm8150l_flash: led-controller@d300 { 120 compatible = "qcom,pm8150l-flash-led", "qcom,spmi-flash-led"; 121 reg = <0xd300>; 122 status = "disabled"; 123 }; 124 125 pm8150l_lpg: pwm { 126 compatible = "qcom,pm8150l-lpg"; 127 128 #address-cells = <1>; 129 #size-cells = <0>; 130 #pwm-cells = <2>; 131 132 status = "disabled"; 133 }; 134 135 pm8150l_wled: leds@d800 { 136 compatible = "qcom,pm8150l-wled"; 137 reg = <0xd800>, <0xd900>; 138 interrupts = <0x5 0xd8 0x1 IRQ_TYPE_EDGE_RISING>, 139 <0x5 0xd8 0x2 IRQ_TYPE_EDGE_RISING>; 140 interrupt-names = "ovp", "short"; 141 label = "backlight"; 142 143 status = "disabled"; 144 }; 145 }; 146}; 147