1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2019, The Linux Foundation. All rights reserved. 4 */ 5 6#include <dt-bindings/iio/qcom,spmi-vadc.h> 7#include <dt-bindings/interrupt-controller/irq.h> 8#include <dt-bindings/spmi/spmi.h> 9 10/ { 11 thermal-zones { 12 pm6150l-thermal { 13 polling-delay-passive = <0>; 14 polling-delay = <0>; 15 16 thermal-sensors = <&pm6150l_temp>; 17 18 trips { 19 trip0 { 20 temperature = <95000>; 21 hysteresis = <0>; 22 type = "passive"; 23 }; 24 25 trip1 { 26 temperature = <115000>; 27 hysteresis = <0>; 28 type = "hot"; 29 }; 30 31 trip2 { 32 temperature = <125000>; 33 hysteresis = <0>; 34 type = "critical"; 35 }; 36 }; 37 }; 38 }; 39}; 40 41&spmi_bus { 42 pm6150l_lsid4: pmic@4 { 43 compatible = "qcom,pm6150l", "qcom,spmi-pmic"; 44 reg = <0x4 SPMI_USID>; 45 #address-cells = <1>; 46 #size-cells = <0>; 47 48 pm6150l_temp: temp-alarm@2400 { 49 compatible = "qcom,spmi-temp-alarm"; 50 reg = <0x2400>; 51 interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; 52 #thermal-sensor-cells = <0>; 53 }; 54 55 pm6150l_adc: adc@3100 { 56 compatible = "qcom,spmi-adc5"; 57 reg = <0x3100>; 58 interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 59 #address-cells = <1>; 60 #size-cells = <0>; 61 #io-channel-cells = <1>; 62 63 channel@0 { 64 reg = <ADC5_REF_GND>; 65 qcom,pre-scaling = <1 1>; 66 label = "ref_gnd"; 67 }; 68 69 channel@1 { 70 reg = <ADC5_1P25VREF>; 71 qcom,pre-scaling = <1 1>; 72 label = "vref_1p25"; 73 }; 74 75 channel@6 { 76 reg = <ADC5_DIE_TEMP>; 77 qcom,pre-scaling = <1 1>; 78 label = "die_temp"; 79 }; 80 81 channel@83 { 82 reg = <ADC5_VPH_PWR>; 83 qcom,pre-scaling = <1 3>; 84 label = "vph_pwr"; 85 }; 86 }; 87 88 pm6150l_adc_tm: adc-tm@3500 { 89 compatible = "qcom,spmi-adc-tm5"; 90 reg = <0x3500>; 91 interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>; 92 #thermal-sensor-cells = <1>; 93 #address-cells = <1>; 94 #size-cells = <0>; 95 status = "disabled"; 96 }; 97 98 pm6150l_gpios: gpio@c000 { 99 compatible = "qcom,pm6150l-gpio", "qcom,spmi-gpio"; 100 reg = <0xc000>; 101 gpio-controller; 102 gpio-ranges = <&pm6150l_gpios 0 0 12>; 103 #gpio-cells = <2>; 104 interrupt-controller; 105 #interrupt-cells = <2>; 106 }; 107 }; 108 109 pm6150l_lsid5: pmic@5 { 110 compatible = "qcom,pm6150l", "qcom,spmi-pmic"; 111 reg = <0x5 SPMI_USID>; 112 #address-cells = <1>; 113 #size-cells = <0>; 114 115 pm6150l_flash: led-controller@d300 { 116 compatible = "qcom,pm6150l-flash-led", "qcom,spmi-flash-led"; 117 reg = <0xd300>; 118 status = "disabled"; 119 }; 120 121 pm6150l_lpg: pwm { 122 compatible = "qcom,pm6150l-lpg", "qcom,pm8150l-lpg"; 123 124 #address-cells = <1>; 125 #size-cells = <0>; 126 #pwm-cells = <2>; 127 128 status = "disabled"; 129 }; 130 131 pm6150l_wled: leds@d800 { 132 compatible = "qcom,pm6150l-wled"; 133 reg = <0xd800>, <0xd900>; 134 interrupts = <0x5 0xd8 0x1 IRQ_TYPE_EDGE_RISING>, 135 <0x5 0xd8 0x2 IRQ_TYPE_EDGE_RISING>; 136 interrupt-names = "ovp", "short"; 137 label = "backlight"; 138 139 status = "disabled"; 140 }; 141 }; 142}; 143