1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2019, The Linux Foundation. All rights reserved. 4 */ 5 6#include <dt-bindings/iio/qcom,spmi-vadc.h> 7#include <dt-bindings/input/linux-event-codes.h> 8#include <dt-bindings/interrupt-controller/irq.h> 9#include <dt-bindings/spmi/spmi.h> 10#include <dt-bindings/thermal/thermal.h> 11 12/ { 13 thermal-zones { 14 pm6150_thermal: pm6150-thermal { 15 polling-delay-passive = <100>; 16 17 thermal-sensors = <&pm6150_temp>; 18 19 trips { 20 pm6150_trip0: trip0 { 21 temperature = <95000>; 22 hysteresis = <0>; 23 type = "passive"; 24 }; 25 26 pm6150_crit: crit { 27 temperature = <115000>; 28 hysteresis = <0>; 29 type = "critical"; 30 }; 31 }; 32 }; 33 }; 34}; 35 36&spmi_bus { 37 pm6150_lsid0: pmic@0 { 38 compatible = "qcom,pm6150", "qcom,spmi-pmic"; 39 reg = <0x0 SPMI_USID>; 40 #address-cells = <1>; 41 #size-cells = <0>; 42 43 pm6150_pon: pon@800 { 44 compatible = "qcom,pm8998-pon"; 45 reg = <0x800>; 46 mode-bootloader = <0x2>; 47 mode-recovery = <0x1>; 48 49 pm6150_pwrkey: pwrkey { 50 compatible = "qcom,pm8941-pwrkey"; 51 interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; 52 debounce = <15625>; 53 bias-pull-up; 54 linux,code = <KEY_POWER>; 55 }; 56 57 pm6150_resin: resin { 58 compatible = "qcom,pm8941-resin"; 59 interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; 60 debounce = <15625>; 61 bias-pull-up; 62 status = "disabled"; 63 }; 64 }; 65 66 pm6150_vbus: usb-vbus-regulator@1100 { 67 compatible = "qcom,pm6150-vbus-reg", 68 "qcom,pm8150b-vbus-reg"; 69 reg = <0x1100>; 70 status = "disabled"; 71 }; 72 73 pm6150_typec: typec@1500 { 74 compatible = "qcom,pm6150-typec", 75 "qcom,pm8150b-typec"; 76 reg = <0x1500>, <0x1700>; 77 interrupts = <0x0 0x15 0x00 IRQ_TYPE_EDGE_RISING>, 78 <0x0 0x15 0x01 IRQ_TYPE_EDGE_BOTH>, 79 <0x0 0x15 0x02 IRQ_TYPE_EDGE_RISING>, 80 <0x0 0x15 0x03 IRQ_TYPE_EDGE_BOTH>, 81 <0x0 0x15 0x04 IRQ_TYPE_EDGE_RISING>, 82 <0x0 0x15 0x05 IRQ_TYPE_EDGE_RISING>, 83 <0x0 0x15 0x06 IRQ_TYPE_EDGE_BOTH>, 84 <0x0 0x15 0x07 IRQ_TYPE_EDGE_RISING>, 85 <0x0 0x17 0x00 IRQ_TYPE_EDGE_RISING>, 86 <0x0 0x17 0x01 IRQ_TYPE_EDGE_RISING>, 87 <0x0 0x17 0x02 IRQ_TYPE_EDGE_RISING>, 88 <0x0 0x17 0x03 IRQ_TYPE_EDGE_RISING>, 89 <0x0 0x17 0x04 IRQ_TYPE_EDGE_RISING>, 90 <0x0 0x17 0x05 IRQ_TYPE_EDGE_RISING>, 91 <0x0 0x17 0x06 IRQ_TYPE_EDGE_RISING>, 92 <0x0 0x17 0x07 IRQ_TYPE_EDGE_RISING>; 93 interrupt-names = "or-rid-detect-change", 94 "vpd-detect", 95 "cc-state-change", 96 "vconn-oc", 97 "vbus-change", 98 "attach-detach", 99 "legacy-cable-detect", 100 "try-snk-src-detect", 101 "sig-tx", 102 "sig-rx", 103 "msg-tx", 104 "msg-rx", 105 "msg-tx-failed", 106 "msg-tx-discarded", 107 "msg-rx-discarded", 108 "fr-swap"; 109 status = "disabled"; 110 }; 111 112 pm6150_temp: temp-alarm@2400 { 113 compatible = "qcom,spmi-temp-alarm"; 114 reg = <0x2400>; 115 interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; 116 io-channels = <&pm6150_adc ADC5_DIE_TEMP>; 117 io-channel-names = "thermal"; 118 #thermal-sensor-cells = <0>; 119 }; 120 121 pm6150_adc: adc@3100 { 122 compatible = "qcom,spmi-adc5"; 123 reg = <0x3100>; 124 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 125 #address-cells = <1>; 126 #size-cells = <0>; 127 #io-channel-cells = <1>; 128 129 channel@6 { 130 reg = <ADC5_DIE_TEMP>; 131 label = "die_temp"; 132 }; 133 }; 134 135 pm6150_adc_tm: adc-tm@3500 { 136 compatible = "qcom,spmi-adc-tm5"; 137 reg = <0x3500>; 138 interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; 139 #thermal-sensor-cells = <1>; 140 #address-cells = <1>; 141 #size-cells = <0>; 142 status = "disabled"; 143 }; 144 145 pm6150_rtc: rtc@6000 { 146 compatible = "qcom,pm8941-rtc"; 147 reg = <0x6000>, <0x6100>; 148 reg-names = "rtc", "alarm"; 149 interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; 150 status = "disabled"; 151 }; 152 153 pm6150_gpios: gpio@c000 { 154 compatible = "qcom,pm6150-gpio", "qcom,spmi-gpio"; 155 reg = <0xc000>; 156 gpio-controller; 157 gpio-ranges = <&pm6150_gpios 0 0 10>; 158 #gpio-cells = <2>; 159 interrupt-controller; 160 #interrupt-cells = <2>; 161 }; 162 }; 163 164 pm6150_lsid1: pmic@1 { 165 compatible = "qcom,pm6150", "qcom,spmi-pmic"; 166 reg = <0x1 SPMI_USID>; 167 #address-cells = <1>; 168 #size-cells = <0>; 169 170 pm6150_vib: vibrator@5300 { 171 compatible = "qcom,pm6150-vib", "qcom,pmi632-vib"; 172 reg = <0x5300>; 173 status = "disabled"; 174 }; 175 }; 176}; 177