1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * OnePlus 5(T) (cheeseburger / dumpling) common device tree source based on msm8998-mtp.dtsi 4 * 5 * Copyright (c) 2021, Jami Kettunen <jamipkettunen@gmail.com> 6 * Copyright (c) 2016, The Linux Foundation. All rights reserved. 7 */ 8 9/dts-v1/; 10 11#include <dt-bindings/gpio/gpio.h> 12#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> 13#include "msm8998.dtsi" 14#include "pm8998.dtsi" 15#include "pmi8998.dtsi" 16#include "pm8005.dtsi" 17 18/ { 19 /* Required for bootloader to select correct board */ 20 qcom,msm-id = <292 0x20001>; /* 8998 v2.1 */ 21 22 chosen { 23 #address-cells = <2>; 24 #size-cells = <2>; 25 ranges; 26 27 /* Use display framebuffer setup by the UEFI XBL bootloader for simplefb */ 28 framebuffer0: framebuffer@9d400000 { 29 compatible = "simple-framebuffer"; 30 reg = <0x0 0x9d400000 0x0 0x2400000>; 31 width = <1080>; 32 height = <1920>; 33 stride = <(1080 * 4)>; 34 format = "a8r8g8b8"; 35 }; 36 }; 37 38 reserved-memory { 39 /* Bootloader display framebuffer region */ 40 cont_splash_mem: memory@9d400000 { 41 reg = <0x0 0x9d400000 0x0 0x2400000>; 42 no-map; 43 }; 44 45 /* For getting crash logs using Android downstream kernels */ 46 ramoops@ac000000 { 47 compatible = "ramoops"; 48 reg = <0x0 0xac000000 0x0 0x200000>; 49 console-size = <0x80000>; 50 pmsg-size = <0x40000>; 51 record-size = <0x8000>; 52 ftrace-size = <0x20000>; 53 }; 54 55 /* 56 * The following memory regions on downstream are "dynamically allocated" 57 * but given the same addresses every time. Hard code them as these addresses 58 * are where the OnePlus signed firmware expects them to be. 59 */ 60 ipa_fws_region: ipa@f6800000 { 61 compatible = "shared-dma-pool"; 62 reg = <0x0 0xf6800000 0x0 0x5000>; 63 no-map; 64 }; 65 zap_shader_region: gpu@f6900000 { 66 compatible = "shared-dma-pool"; 67 reg = <0x0 0xf6900000 0x0 0x2000>; 68 no-map; 69 }; 70 }; 71 72 gpio-keys { 73 compatible = "gpio-keys"; 74 label = "Volume buttons"; 75 autorepeat; 76 77 pinctrl-names = "default"; 78 pinctrl-0 = <&vol_keys_default>; 79 80 vol-down { 81 label = "Volume down"; 82 gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>; 83 linux,code = <KEY_VOLUMEDOWN>; 84 debounce-interval = <15>; 85 wakeup-source; 86 }; 87 88 vol-up { 89 label = "Volume up"; 90 gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; 91 linux,code = <KEY_VOLUMEUP>; 92 debounce-interval = <15>; 93 wakeup-source; 94 }; 95 }; 96 97 gpio-hall-sensor { 98 compatible = "gpio-keys"; 99 label = "Hall effect sensor"; 100 101 pinctrl-names = "default"; 102 pinctrl-0 = <&hall_sensor_default>; 103 104 hall-sensor { 105 label = "Hall Effect Sensor"; 106 gpios = <&tlmm 124 GPIO_ACTIVE_LOW>; 107 linux,input-type = <EV_SW>; 108 linux,code = <SW_LID>; 109 linux,can-disable; 110 wakeup-source; 111 }; 112 }; 113 114 vph_pwr: vph-pwr-regulator { 115 compatible = "regulator-fixed"; 116 regulator-name = "vph_pwr"; 117 regulator-always-on; 118 regulator-boot-on; 119 }; 120}; 121 122/* 123 * OnePlus' ADSP firmware requires 30 MiB in total, so increase the adsp_mem 124 * region by 4 MiB to account for this while relocating the other now 125 * conflicting memory nodes accordingly. 126 */ 127&adsp_mem { 128 reg = <0x0 0x8b200000 0x0 0x1e00000>; 129}; 130&mpss_mem { 131 reg = <0x0 0x8d000000 0x0 0x7000000>; 132}; 133&venus_mem { 134 reg = <0x0 0x94000000 0x0 0x500000>; 135}; 136&mba_mem { 137 reg = <0x0 0x94500000 0x0 0x200000>; 138}; 139&slpi_mem { 140 reg = <0x0 0x94700000 0x0 0xf00000>; 141}; 142&ipa_fw_mem { 143 reg = <0x0 0x95600000 0x0 0x10000>; 144}; 145&ipa_gsi_mem { 146 reg = <0x0 0x95610000 0x0 0x5000>; 147}; 148&gpu_mem { 149 reg = <0x0 0x95615000 0x0 0x100000>; 150}; 151&wlan_msa_mem { 152 reg = <0x0 0x95715000 0x0 0x100000>; 153}; 154 155&blsp1_i2c5 { 156 status = "okay"; 157 158 touchscreen@20 { 159 compatible = "syna,rmi4-i2c"; 160 reg = <0x20>; 161 #address-cells = <1>; 162 #size-cells = <0>; 163 164 interrupt-parent = <&tlmm>; 165 interrupts = <125 IRQ_TYPE_EDGE_FALLING>; 166 167 pinctrl-names = "default"; 168 pinctrl-0 = <&ts_int_active &ts_reset_active>; 169 170 vdd-supply = <&vreg_l28_3p0>; 171 vio-supply = <&vreg_l6a_1p8>; 172 173 syna,reset-delay-ms = <20>; 174 syna,startup-delay-ms = <20>; 175 176 rmi4-f01@1 { 177 reg = <0x01>; 178 syna,nosleep-mode = <1>; 179 }; 180 181 rmi4_f12: rmi4-f12@12 { 182 reg = <0x12>; 183 syna,rezero-wait-ms = <20>; 184 syna,sensor-type = <1>; 185 touchscreen-x-mm = <68>; 186 touchscreen-y-mm = <122>; 187 }; 188 }; 189}; 190 191&blsp1_uart3 { 192 status = "okay"; 193 194 bluetooth { 195 compatible = "qcom,wcn3990-bt"; 196 197 vddio-supply = <&vreg_s4a_1p8>; 198 vddxo-supply = <&vreg_l7a_1p8>; 199 vddrf-supply = <&vreg_l17a_1p3>; 200 vddch0-supply = <&vreg_l25a_3p3>; 201 max-speed = <3200000>; 202 }; 203}; 204 205&blsp1_uart3_on { 206 rx { 207 /delete-property/ bias-disable; 208 /* 209 * Configure a pull-up on 46 (RX). This is needed to 210 * avoid garbage data when the TX pin of the Bluetooth 211 * module is in tri-state (module powered off or not 212 * driving the signal yet). 213 */ 214 bias-pull-up; 215 }; 216 217 cts { 218 /delete-property/ bias-disable; 219 /* 220 * Configure a pull-down on 47 (CTS) to match the pull 221 * of the Bluetooth module. 222 */ 223 bias-pull-down; 224 }; 225}; 226 227&blsp2_uart1 { 228 status = "okay"; 229}; 230 231&pm8005_lsid1 { 232 pm8005-regulators { 233 compatible = "qcom,pm8005-regulators"; 234 235 vdd_s1-supply = <&vph_pwr>; 236 237 pm8005_s1: s1 { /* VDD_GFX supply */ 238 regulator-min-microvolt = <524000>; 239 regulator-max-microvolt = <1100000>; 240 regulator-enable-ramp-delay = <500>; 241 242 /* hack until we rig up the gpu consumer */ 243 regulator-always-on; 244 }; 245 }; 246}; 247 248&pm8998_gpio { 249 vol_keys_default: vol-keys-default { 250 pinconf { 251 pins = "gpio5", "gpio6"; 252 function = "normal"; 253 bias-pull-up; 254 input-enable; 255 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; 256 }; 257 }; 258}; 259 260&qusb2phy { 261 status = "okay"; 262 263 vdda-pll-supply = <&vreg_l12a_1p8>; 264 vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; 265}; 266 267&rpm_requests { 268 pm8998-regulators { 269 compatible = "qcom,rpm-pm8998-regulators"; 270 271 vdd_s1-supply = <&vph_pwr>; 272 vdd_s2-supply = <&vph_pwr>; 273 vdd_s3-supply = <&vph_pwr>; 274 vdd_s4-supply = <&vph_pwr>; 275 vdd_s5-supply = <&vph_pwr>; 276 vdd_s6-supply = <&vph_pwr>; 277 vdd_s7-supply = <&vph_pwr>; 278 vdd_s8-supply = <&vph_pwr>; 279 vdd_s9-supply = <&vph_pwr>; 280 vdd_s10-supply = <&vph_pwr>; 281 vdd_s11-supply = <&vph_pwr>; 282 vdd_s12-supply = <&vph_pwr>; 283 vdd_s13-supply = <&vph_pwr>; 284 vdd_l1_l27-supply = <&vreg_s7a_1p025>; 285 vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>; 286 vdd_l3_l11-supply = <&vreg_s7a_1p025>; 287 vdd_l4_l5-supply = <&vreg_s7a_1p025>; 288 vdd_l6-supply = <&vreg_s5a_2p04>; 289 vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>; 290 vdd_l9-supply = <&vreg_bob>; 291 vdd_l10_l23_l25-supply = <&vreg_bob>; 292 vdd_l13_l19_l21-supply = <&vreg_bob>; 293 vdd_l16_l28-supply = <&vreg_bob>; 294 vdd_l18_l22-supply = <&vreg_bob>; 295 vdd_l20_l24-supply = <&vreg_bob>; 296 vdd_l26-supply = <&vreg_s3a_1p35>; 297 vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>; 298 299 vreg_s3a_1p35: s3 { 300 regulator-min-microvolt = <1352000>; 301 regulator-max-microvolt = <1352000>; 302 }; 303 vreg_s4a_1p8: s4 { 304 regulator-min-microvolt = <1800000>; 305 regulator-max-microvolt = <1800000>; 306 regulator-allow-set-load; 307 }; 308 vreg_s5a_2p04: s5 { 309 regulator-min-microvolt = <1904000>; 310 regulator-max-microvolt = <2040000>; 311 }; 312 vreg_s7a_1p025: s7 { 313 regulator-min-microvolt = <900000>; 314 regulator-max-microvolt = <1028000>; 315 }; 316 vreg_l1a_0p875: l1 { 317 regulator-min-microvolt = <880000>; 318 regulator-max-microvolt = <880000>; 319 }; 320 vreg_l2a_1p2: l2 { 321 regulator-min-microvolt = <1200000>; 322 regulator-max-microvolt = <1200000>; 323 }; 324 vreg_l3a_1p0: l3 { 325 regulator-min-microvolt = <1000000>; 326 regulator-max-microvolt = <1000000>; 327 }; 328 vreg_l5a_0p8: l5 { 329 regulator-min-microvolt = <800000>; 330 regulator-max-microvolt = <800000>; 331 }; 332 vreg_l6a_1p8: l6 { 333 regulator-min-microvolt = <1808000>; 334 regulator-max-microvolt = <1808000>; 335 }; 336 vreg_l7a_1p8: l7 { 337 regulator-min-microvolt = <1800000>; 338 regulator-max-microvolt = <1800000>; 339 }; 340 vreg_l8a_1p2: l8 { 341 regulator-min-microvolt = <1200000>; 342 regulator-max-microvolt = <1200000>; 343 }; 344 vreg_l9a_1p8: l9 { 345 regulator-min-microvolt = <1808000>; 346 regulator-max-microvolt = <2960000>; 347 }; 348 vreg_l10a_1p8: l10 { 349 regulator-min-microvolt = <1808000>; 350 regulator-max-microvolt = <2960000>; 351 }; 352 vreg_l11a_1p0: l11 { 353 regulator-min-microvolt = <1000000>; 354 regulator-max-microvolt = <1000000>; 355 }; 356 vreg_l12a_1p8: l12 { 357 regulator-min-microvolt = <1800000>; 358 regulator-max-microvolt = <1800000>; 359 }; 360 vreg_l13a_2p95: l13 { 361 regulator-min-microvolt = <1808000>; 362 regulator-max-microvolt = <2960000>; 363 }; 364 vreg_l14a_1p88: l14 { 365 regulator-min-microvolt = <1880000>; 366 regulator-max-microvolt = <1880000>; 367 }; 368 vreg_l15a_1p8: l15 { 369 regulator-min-microvolt = <1800000>; 370 regulator-max-microvolt = <1800000>; 371 }; 372 vreg_l16a_2p7: l16 { 373 regulator-min-microvolt = <2704000>; 374 regulator-max-microvolt = <2704000>; 375 }; 376 vreg_l17a_1p3: l17 { 377 regulator-min-microvolt = <1304000>; 378 regulator-max-microvolt = <1304000>; 379 }; 380 vreg_l18a_2p7: l18 { 381 regulator-min-microvolt = <2704000>; 382 regulator-max-microvolt = <2704000>; 383 }; 384 vreg_l19a_3p0: l19 { 385 regulator-min-microvolt = <3008000>; 386 regulator-max-microvolt = <3008000>; 387 }; 388 vreg_l20a_2p95: l20 { 389 regulator-min-microvolt = <2960000>; 390 regulator-max-microvolt = <2960000>; 391 regulator-allow-set-load; 392 }; 393 vreg_l21a_2p95: l21 { 394 regulator-min-microvolt = <2960000>; 395 regulator-max-microvolt = <2960000>; 396 regulator-allow-set-load; 397 regulator-system-load = <800000>; 398 }; 399 vreg_l22a_2p85: l22 { 400 regulator-min-microvolt = <2864000>; 401 regulator-max-microvolt = <2864000>; 402 }; 403 vreg_l23a_3p3: l23 { 404 regulator-min-microvolt = <3312000>; 405 regulator-max-microvolt = <3312000>; 406 }; 407 vreg_l24a_3p075: l24 { 408 regulator-min-microvolt = <3088000>; 409 regulator-max-microvolt = <3088000>; 410 }; 411 vreg_l25a_3p3: l25 { 412 regulator-min-microvolt = <3104000>; 413 regulator-max-microvolt = <3312000>; 414 }; 415 vreg_l26a_1p2: l26 { 416 regulator-min-microvolt = <1200000>; 417 regulator-max-microvolt = <1200000>; 418 regulator-allow-set-load; 419 }; 420 vreg_l28_3p0: l28 { 421 regulator-min-microvolt = <3008000>; 422 regulator-max-microvolt = <3008000>; 423 }; 424 vreg_lvs1a_1p8: lvs1 { }; 425 vreg_lvs2a_1p8: lvs2 { }; 426 }; 427 428 pmi8998-regulators { 429 compatible = "qcom,rpm-pmi8998-regulators"; 430 431 vdd_bob-supply = <&vph_pwr>; 432 433 vreg_bob: bob { 434 regulator-min-microvolt = <3312000>; 435 regulator-max-microvolt = <3600000>; 436 }; 437 }; 438}; 439 440&tlmm { 441 gpio-reserved-ranges = <0 4>, <81 4>; 442 443 hall_sensor_default: hall-sensor-default { 444 pins = "gpio124"; 445 function = "gpio"; 446 drive-strength = <2>; 447 bias-disable; 448 input-enable; 449 }; 450 451 ts_int_active: ts-int-active { 452 pins = "gpio125"; 453 function = "gpio"; 454 drive-strength = <8>; 455 bias-pull-up; 456 }; 457 458 ts_reset_active: ts-reset-active { 459 pins = "gpio89"; 460 function = "gpio"; 461 drive-strength = <8>; 462 bias-pull-up; 463 }; 464}; 465 466&ufshc { 467 status = "okay"; 468 469 vcc-supply = <&vreg_l20a_2p95>; 470 vccq-supply = <&vreg_l26a_1p2>; 471 vccq2-supply = <&vreg_s4a_1p8>; 472 vcc-max-microamp = <750000>; 473 vccq-max-microamp = <560000>; 474 vccq2-max-microamp = <750000>; 475}; 476 477&ufsphy { 478 status = "okay"; 479 480 vdda-phy-supply = <&vreg_l1a_0p875>; 481 vdda-pll-supply = <&vreg_l2a_1p2>; 482 vddp-ref-clk-supply = <&vreg_l26a_1p2>; 483 vdda-phy-max-microamp = <51400>; 484 vdda-pll-max-microamp = <14600>; 485 vddp-ref-clk-max-microamp = <100>; 486 vddp-ref-clk-always-on; 487}; 488 489&usb3 { 490 status = "okay"; 491 492 /* Disable USB3 clock requirement as the device only supports USB2 */ 493 qcom,select-utmi-as-pipe-clk; 494}; 495 496&usb3_dwc3 { 497 /* Drop the unused USB 3 PHY */ 498 phys = <&qusb2phy>; 499 phy-names = "usb2-phy"; 500 501 /* Fastest mode for USB 2 */ 502 maximum-speed = "high-speed"; 503 504 /* Force to peripheral until we can switch modes */ 505 dr_mode = "peripheral"; 506}; 507 508&wifi { 509 /* Leave disabled until MSS is functional */ 510 vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; 511 vdd-1.8-xo-supply = <&vreg_l7a_1p8>; 512 vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; 513 vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; 514}; 515