1// SPDX-License-Identifier: GPL-2.0-only 2 3#include "msm8916-pm8916.dtsi" 4#include "msm8916-modem-qdsp6.dtsi" 5 6#include <dt-bindings/gpio/gpio.h> 7#include <dt-bindings/input/input.h> 8#include <dt-bindings/interrupt-controller/irq.h> 9 10/ { 11 aliases { 12 mmc0 = &sdhc_1; /* eMMC */ 13 mmc1 = &sdhc_2; /* SD card */ 14 serial0 = &blsp_uart1; 15 }; 16 17 chosen { 18 stdout-path = "serial0"; 19 }; 20 21 gpio-keys { 22 compatible = "gpio-keys"; 23 24 pinctrl-0 = <&gpio_keys_default>; 25 pinctrl-names = "default"; 26 27 label = "GPIO Buttons"; 28 29 volume-up-button { 30 label = "Volume Up"; 31 gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; 32 linux,code = <KEY_VOLUMEUP>; 33 debounce-interval = <15>; 34 }; 35 }; 36 37 usb_id: usb-id { 38 compatible = "linux,extcon-usb-gpio"; 39 id-gpios = <&tlmm 91 GPIO_ACTIVE_HIGH>; 40 pinctrl-0 = <&usb_id_default>; 41 pinctrl-1 = <&usb_id_sleep>; 42 pinctrl-names = "default", "sleep"; 43 }; 44}; 45 46&blsp_i2c2 { 47 status = "okay"; 48 49 touchscreen: touchscreen@20 { 50 compatible = "syna,rmi4-i2c"; 51 reg = <0x20>; 52 #address-cells = <1>; 53 #size-cells = <0>; 54 55 vio-supply = <&pm8916_l6>; 56 57 syna,startup-delay-ms = <100>; 58 59 rmi4-f01@1 { 60 reg = <1>; 61 syna,nosleep-mode = <1>; /* Allow sleeping */ 62 }; 63 64 rmi4-f11@11 { 65 reg = <11>; 66 syna,sensor-type = <1>; /* Touchscreen */ 67 }; 68 }; 69}; 70 71&blsp_uart1 { 72 status = "okay"; 73}; 74 75&mpss_mem { 76 reg = <0x0 0x86800000 0x0 0x5500000>; 77}; 78 79&pm8916_resin { 80 linux,code = <KEY_VOLUMEDOWN>; 81 status = "okay"; 82}; 83 84&pm8916_rpm_regulators { 85 pm8916_l16: l16 { 86 regulator-min-microvolt = <3100000>; 87 regulator-max-microvolt = <3300000>; 88 }; 89}; 90 91&pm8916_vib { 92 status = "okay"; 93}; 94 95&sdhc_1 { 96 status = "okay"; 97}; 98 99&sdhc_2 { 100 status = "okay"; 101}; 102 103&usb { 104 extcon = <&usb_id>, <&usb_id>; 105 status = "okay"; 106}; 107 108&usb_hs_phy { 109 extcon = <&usb_id>; 110}; 111 112&venus { 113 status = "okay"; 114}; 115 116&venus_mem { 117 status = "okay"; 118}; 119 120&wcnss { 121 status = "okay"; 122}; 123 124&wcnss_iris { 125 compatible = "qcom,wcn3620"; 126}; 127 128&wcnss_mem { 129 status = "okay"; 130}; 131 132/* CTS/RTX are not used */ 133&blsp_uart1_default { 134 pins = "gpio0", "gpio1"; 135}; 136&blsp_uart1_sleep { 137 pins = "gpio0", "gpio1"; 138}; 139 140&tlmm { 141 gpio_keys_default: gpio-keys-default-state { 142 pins = "gpio107"; 143 function = "gpio"; 144 drive-strength = <2>; 145 bias-pull-up; 146 }; 147 148 usb_id_default: usb-id-default-state { 149 pins = "gpio91"; 150 function = "gpio"; 151 drive-strength = <8>; 152 bias-pull-up; 153 }; 154 155 usb_id_sleep: usb-id-sleep-state { 156 pins = "gpio91"; 157 function = "gpio"; 158 drive-strength = <8>; 159 bias-disable; 160 }; 161}; 162