1/* 2 * BSD LICENSE 3 * 4 * Copyright(c) 2016-2017 Broadcom. All rights reserved. 5 * 6 * Redistribution and use in source and binary forms, with or without 7 * modification, are permitted provided that the following conditions 8 * are met: 9 * 10 * * Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * * Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in 14 * the documentation and/or other materials provided with the 15 * distribution. 16 * * Neither the name of Broadcom nor the names of its 17 * contributors may be used to endorse or promote products derived 18 * from this software without specific prior written permission. 19 * 20 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 21 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 22 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR 23 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 24 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, 25 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT 26 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 27 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 28 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 29 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE 30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 31 */ 32 33#include "stingray-board-base.dtsi" 34 35/ { 36 sdio0_vddo_ctrl_reg: sdio0_vddo_ctrl { 37 compatible = "regulator-gpio"; 38 regulator-name = "sdio0_vddo_ctrl_reg"; 39 regulator-type = "voltage"; 40 regulator-min-microvolt = <1800000>; 41 regulator-max-microvolt = <3300000>; 42 gpios = <&pca9505 18 0>; 43 states = <3300000 0x0 44 1800000 0x1>; 45 }; 46 47 sdio1_vddo_ctrl_reg: sdio1_vddo_ctrl { 48 compatible = "regulator-gpio"; 49 regulator-name = "sdio1_vddo_ctrl_reg"; 50 regulator-type = "voltage"; 51 regulator-min-microvolt = <1800000>; 52 regulator-max-microvolt = <3300000>; 53 gpios = <&pca9505 19 0>; 54 states = <3300000 0x0 55 1800000 0x1>; 56 }; 57}; 58 59&sata0 { 60 status = "okay"; 61}; 62 63&sata_phy0{ 64 status = "okay"; 65}; 66 67&sata1 { 68 status = "okay"; 69}; 70 71&sata_phy1{ 72 status = "okay"; 73}; 74 75&sata2 { 76 status = "okay"; 77}; 78 79&sata_phy2{ 80 status = "okay"; 81}; 82 83&sata3 { 84 status = "okay"; 85}; 86 87&sata_phy3{ 88 status = "okay"; 89}; 90 91&sata4 { 92 status = "okay"; 93}; 94 95&sata_phy4{ 96 status = "okay"; 97}; 98 99&sata5 { 100 status = "okay"; 101}; 102 103&sata_phy5{ 104 status = "okay"; 105}; 106 107&sata6 { 108 status = "okay"; 109}; 110 111&sata_phy6{ 112 status = "okay"; 113}; 114 115&sata7 { 116 status = "okay"; 117}; 118 119&sata_phy7{ 120 status = "okay"; 121}; 122 123&pwm { 124 status = "okay"; 125}; 126 127&i2c0 { 128 status = "okay"; 129 130 pca9505: pca9505@20 { 131 compatible = "nxp,pca9505"; 132 gpio-controller; 133 #gpio-cells = <2>; 134 reg = <0x20>; 135 }; 136}; 137 138&i2c1 { 139 status = "okay"; 140 141 pcf8574: pcf8574@27 { 142 compatible = "nxp,pcf8574a"; 143 gpio-controller; 144 #gpio-cells = <2>; 145 reg = <0x27>; 146 }; 147}; 148 149&enet { 150 status = "okay"; 151}; 152 153&nand { 154 status = "ok"; 155 nandcs@0 { 156 compatible = "brcm,nandcs"; 157 reg = <0>; 158 nand-ecc-mode = "hw"; 159 nand-ecc-strength = <8>; 160 nand-ecc-step-size = <512>; 161 nand-bus-width = <16>; 162 brcm,nand-oob-sector-size = <16>; 163 #address-cells = <1>; 164 #size-cells = <1>; 165 }; 166}; 167 168&sdio0 { 169 vqmmc-supply = <&sdio0_vddo_ctrl_reg>; 170 status = "okay"; 171}; 172 173&sdio1 { 174 vqmmc-supply = <&sdio1_vddo_ctrl_reg>; 175 status = "okay"; 176}; 177