1/* 2 * Copyright (C) 2016 ARM Ltd. 3 * Copyright (C) 2018 Hauke Mehrtens <hauke@hauke-m.de> 4 * 5 * SPDX-License-Identifier: (GPL-2.0+ OR X11) 6 */ 7 8/dts-v1/; 9#include "sun50i-h5.dtsi" 10 11#include <dt-bindings/gpio/gpio.h> 12#include <dt-bindings/input/input.h> 13#include <dt-bindings/pinctrl/sun4i-a10.h> 14 15/ { 16 model = "Xunlong Orange Pi Zero Plus"; 17 compatible = "xunlong,orangepi-zero-plus", "allwinner,sun50i-h5"; 18 19 reg_vcc3v3: vcc3v3 { 20 compatible = "regulator-fixed"; 21 regulator-name = "vcc3v3"; 22 regulator-min-microvolt = <3300000>; 23 regulator-max-microvolt = <3300000>; 24 }; 25 26 aliases { 27 ethernet0 = &emac; 28 ethernet1 = &rtl8189ftv; 29 serial0 = &uart0; 30 }; 31 32 chosen { 33 stdout-path = "serial0:115200n8"; 34 }; 35 36 leds { 37 compatible = "gpio-leds"; 38 39 pwr { 40 label = "orangepi:green:pwr"; 41 gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */ 42 default-state = "on"; 43 }; 44 45 status { 46 label = "orangepi:red:status"; 47 gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */ 48 }; 49 }; 50 51 reg_gmac_3v3: gmac-3v3 { 52 compatible = "regulator-fixed"; 53 regulator-name = "gmac-3v3"; 54 regulator-min-microvolt = <3300000>; 55 regulator-max-microvolt = <3300000>; 56 startup-delay-us = <100000>; 57 enable-active-high; 58 gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */ 59 }; 60}; 61 62&ehci0 { 63 status = "okay"; 64}; 65 66&ehci1 { 67 status = "okay"; 68}; 69 70&emac { 71 pinctrl-names = "default"; 72 pinctrl-0 = <&emac_rgmii_pins>; 73 phy-supply = <®_gmac_3v3>; 74 phy-handle = <&ext_rgmii_phy>; 75 phy-mode = "rgmii"; 76 status = "okay"; 77}; 78 79&external_mdio { 80 ext_rgmii_phy: ethernet-phy@1 { 81 compatible = "ethernet-phy-ieee802.3-c22"; 82 reg = <1>; 83 }; 84}; 85 86&mmc0 { 87 vmmc-supply = <®_vcc3v3>; 88 bus-width = <4>; 89 cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ 90 status = "okay"; 91}; 92 93&mmc1 { 94 vmmc-supply = <®_vcc3v3>; 95 bus-width = <4>; 96 non-removable; 97 status = "okay"; 98 99 /* 100 * Explicitly define the sdio device, so that we can add an ethernet 101 * alias for it (which e.g. makes u-boot set a mac-address). 102 */ 103 rtl8189ftv: sdio_wifi@1 { 104 reg = <1>; 105 }; 106}; 107 108&spi0 { 109 status = "okay"; 110 111 flash@0 { 112 #address-cells = <1>; 113 #size-cells = <1>; 114 compatible = "mxicy,mx25l1606e", "winbond,w25q128"; 115 reg = <0>; 116 spi-max-frequency = <40000000>; 117 }; 118}; 119 120&ohci0 { 121 status = "okay"; 122}; 123 124&ohci1 { 125 status = "okay"; 126}; 127 128&uart0 { 129 pinctrl-names = "default"; 130 pinctrl-0 = <&uart0_pins_a>; 131 status = "okay"; 132}; 133 134&usb_otg { 135 dr_mode = "peripheral"; 136 status = "okay"; 137}; 138 139&usbphy { 140 /* USB Type-A ports' VBUS is always on */ 141 usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ 142 status = "okay"; 143}; 144