1// SPDX-License-Identifier: (GPL-2.0+ OR MIT) 2// Copyright (C) 2016 ARM Ltd. 3 4/dts-v1/; 5#include "sun50i-h5.dtsi" 6 7#include <dt-bindings/gpio/gpio.h> 8#include <dt-bindings/input/input.h> 9#include <dt-bindings/pinctrl/sun4i-a10.h> 10 11/ { 12 model = "Xunlong Orange Pi PC 2"; 13 compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5"; 14 15 reg_vcc3v3: vcc3v3 { 16 compatible = "regulator-fixed"; 17 regulator-name = "vcc3v3"; 18 regulator-min-microvolt = <3300000>; 19 regulator-max-microvolt = <3300000>; 20 }; 21 22 aliases { 23 ethernet0 = &emac; 24 serial0 = &uart0; 25 }; 26 27 chosen { 28 stdout-path = "serial0:115200n8"; 29 }; 30 31 connector { 32 compatible = "hdmi-connector"; 33 type = "a"; 34 35 port { 36 hdmi_con_in: endpoint { 37 remote-endpoint = <&hdmi_out_con>; 38 }; 39 }; 40 }; 41 42 leds { 43 compatible = "gpio-leds"; 44 45 led-0 { 46 label = "orangepi:green:pwr"; 47 gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; 48 default-state = "on"; 49 }; 50 51 led-1 { 52 label = "orangepi:red:status"; 53 gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>; 54 }; 55 }; 56 57 r-gpio-keys { 58 compatible = "gpio-keys"; 59 60 sw4 { 61 label = "sw4"; 62 linux,code = <BTN_0>; 63 gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; 64 wakeup-source; 65 }; 66 }; 67 68 reg_gmac_3v3: gmac-3v3 { 69 compatible = "regulator-fixed"; 70 regulator-name = "gmac-3v3"; 71 regulator-min-microvolt = <3300000>; 72 regulator-max-microvolt = <3300000>; 73 startup-delay-us = <100000>; 74 enable-active-high; 75 gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; 76 }; 77 78 reg_usb0_vbus: usb0-vbus { 79 compatible = "regulator-fixed"; 80 regulator-name = "usb0-vbus"; 81 regulator-min-microvolt = <5000000>; 82 regulator-max-microvolt = <5000000>; 83 enable-active-high; 84 gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */ 85 status = "okay"; 86 }; 87}; 88 89&codec { 90 allwinner,audio-routing = 91 "Line Out", "LINEOUT", 92 "MIC1", "Mic", 93 "Mic", "MBIAS"; 94 status = "okay"; 95}; 96 97&cpu0 { 98 cpu-supply = <®_vdd_cpux>; 99}; 100 101&de { 102 status = "okay"; 103}; 104 105&ehci0 { 106 status = "okay"; 107}; 108 109&ehci1 { 110 status = "okay"; 111}; 112 113&ehci2 { 114 status = "okay"; 115}; 116 117&ehci3 { 118 status = "okay"; 119}; 120 121&emac { 122 pinctrl-names = "default"; 123 pinctrl-0 = <&emac_rgmii_pins>; 124 phy-supply = <®_gmac_3v3>; 125 phy-handle = <&ext_rgmii_phy>; 126 phy-mode = "rgmii-id"; 127 status = "okay"; 128}; 129 130&external_mdio { 131 ext_rgmii_phy: ethernet-phy@1 { 132 compatible = "ethernet-phy-ieee802.3-c22"; 133 reg = <1>; 134 }; 135}; 136 137&hdmi { 138 status = "okay"; 139}; 140 141&hdmi_out { 142 hdmi_out_con: endpoint { 143 remote-endpoint = <&hdmi_con_in>; 144 }; 145}; 146 147&ir { 148 pinctrl-names = "default"; 149 pinctrl-0 = <&r_ir_rx_pin>; 150 status = "okay"; 151}; 152 153&mmc0 { 154 vmmc-supply = <®_vcc3v3>; 155 bus-width = <4>; 156 cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ 157 status = "okay"; 158}; 159 160&ohci0 { 161 status = "okay"; 162}; 163 164&ohci1 { 165 status = "okay"; 166}; 167 168&ohci2 { 169 status = "okay"; 170}; 171 172&ohci3 { 173 status = "okay"; 174}; 175 176&r_i2c { 177 status = "okay"; 178 179 reg_vdd_cpux: regulator@65 { 180 compatible = "silergy,sy8106a"; 181 reg = <0x65>; 182 regulator-name = "vdd-cpux"; 183 silergy,fixed-microvolt = <1100000>; 184 regulator-min-microvolt = <1000000>; 185 regulator-max-microvolt = <1400000>; 186 regulator-ramp-delay = <200>; 187 regulator-boot-on; 188 regulator-always-on; 189 }; 190}; 191 192&spi0 { 193 status = "okay"; 194 195 flash@0 { 196 #address-cells = <1>; 197 #size-cells = <1>; 198 compatible = "jedec,spi-nor"; 199 reg = <0>; 200 spi-max-frequency = <40000000>; 201 }; 202}; 203 204&uart0 { 205 pinctrl-names = "default"; 206 pinctrl-0 = <&uart0_pa_pins>; 207 status = "okay"; 208}; 209 210&uart1 { 211 pinctrl-names = "default"; 212 pinctrl-0 = <&uart1_pins>; 213 status = "disabled"; 214}; 215 216&uart2 { 217 pinctrl-names = "default"; 218 pinctrl-0 = <&uart2_pins>; 219 status = "disabled"; 220}; 221 222&usb_otg { 223 dr_mode = "otg"; 224 status = "okay"; 225}; 226 227&usbphy { 228 /* USB Type-A ports' VBUS is always on */ 229 usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ 230 usb0_vbus-supply = <®_usb0_vbus>; 231 status = "okay"; 232}; 233