xref: /linux/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts (revision 72bea132f3680ee51e7ed2cee62892b6f5121909) 
1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2// Copyright (C) 2016 ARM Ltd.
3
4/dts-v1/;
5#include "sun50i-h5.dtsi"
6#include "sun50i-h5-cpu-opp.dtsi"
7
8#include <dt-bindings/gpio/gpio.h>
9#include <dt-bindings/input/input.h>
10#include <dt-bindings/pinctrl/sun4i-a10.h>
11
12/ {
13	model = "Xunlong Orange Pi PC 2";
14	compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
15
16	reg_vcc3v3: vcc3v3 {
17		compatible = "regulator-fixed";
18		regulator-name = "vcc3v3";
19		regulator-min-microvolt = <3300000>;
20		regulator-max-microvolt = <3300000>;
21	};
22
23	aliases {
24		ethernet0 = &emac;
25		serial0 = &uart0;
26	};
27
28	chosen {
29		stdout-path = "serial0:115200n8";
30	};
31
32	connector {
33		compatible = "hdmi-connector";
34		type = "a";
35
36		port {
37			hdmi_con_in: endpoint {
38				remote-endpoint = <&hdmi_out_con>;
39			};
40		};
41	};
42
43	leds {
44		compatible = "gpio-leds";
45
46		led-0 {
47			label = "orangepi:green:pwr";
48			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
49			default-state = "on";
50		};
51
52		led-1 {
53			label = "orangepi:red:status";
54			gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
55		};
56	};
57
58	gpio-keys {
59		compatible = "gpio-keys";
60
61		key-sw4 {
62			label = "sw4";
63			linux,code = <BTN_0>;
64			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
65			wakeup-source;
66		};
67	};
68
69	reg_gmac_3v3: gmac-3v3 {
70		compatible = "regulator-fixed";
71		regulator-name = "gmac-3v3";
72		regulator-min-microvolt = <3300000>;
73		regulator-max-microvolt = <3300000>;
74		startup-delay-us = <100000>;
75		enable-active-high;
76		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
77	};
78
79	reg_usb0_vbus: usb0-vbus {
80		compatible = "regulator-fixed";
81		regulator-name = "usb0-vbus";
82		regulator-min-microvolt = <5000000>;
83		regulator-max-microvolt = <5000000>;
84		enable-active-high;
85		gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
86		status = "okay";
87	};
88};
89
90&codec {
91	allwinner,audio-routing =
92		"Line Out", "LINEOUT",
93		"MIC1", "Mic",
94		"Mic",  "MBIAS";
95	status = "okay";
96};
97
98&cpu0 {
99	cpu-supply = <&reg_vdd_cpux>;
100};
101
102&de {
103	status = "okay";
104};
105
106&ehci0 {
107	status = "okay";
108};
109
110&ehci1 {
111	status = "okay";
112};
113
114&ehci2 {
115	status = "okay";
116};
117
118&ehci3 {
119	status = "okay";
120};
121
122&emac {
123	pinctrl-names = "default";
124	pinctrl-0 = <&emac_rgmii_pins>;
125	phy-supply = <&reg_gmac_3v3>;
126	phy-handle = <&ext_rgmii_phy>;
127	phy-mode = "rgmii-id";
128	status = "okay";
129};
130
131&external_mdio {
132	ext_rgmii_phy: ethernet-phy@1 {
133		compatible = "ethernet-phy-ieee802.3-c22";
134		reg = <1>;
135	};
136};
137
138&hdmi {
139	status = "okay";
140};
141
142&hdmi_out {
143	hdmi_out_con: endpoint {
144		remote-endpoint = <&hdmi_con_in>;
145	};
146};
147
148&ir {
149	pinctrl-names = "default";
150	pinctrl-0 = <&r_ir_rx_pin>;
151	status = "okay";
152};
153
154&mmc0 {
155	vmmc-supply = <&reg_vcc3v3>;
156	bus-width = <4>;
157	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
158	status = "okay";
159};
160
161&ohci0 {
162	status = "okay";
163};
164
165&ohci1 {
166	status = "okay";
167};
168
169&ohci2 {
170	status = "okay";
171};
172
173&ohci3 {
174	status = "okay";
175};
176
177&r_i2c {
178	status = "okay";
179
180	reg_vdd_cpux: regulator@65 {
181		compatible = "silergy,sy8106a";
182		reg = <0x65>;
183		regulator-name = "vdd-cpux";
184		silergy,fixed-microvolt = <1100000>;
185		regulator-min-microvolt = <1000000>;
186		regulator-max-microvolt = <1400000>;
187		regulator-ramp-delay = <200>;
188		regulator-boot-on;
189		regulator-always-on;
190	};
191};
192
193&spi0  {
194	status = "okay";
195
196	flash@0 {
197		#address-cells = <1>;
198		#size-cells = <1>;
199		compatible = "jedec,spi-nor";
200		reg = <0>;
201		spi-max-frequency = <40000000>;
202	};
203};
204
205&uart0 {
206	pinctrl-names = "default";
207	pinctrl-0 = <&uart0_pa_pins>;
208	status = "okay";
209};
210
211&uart1 {
212	pinctrl-names = "default";
213	pinctrl-0 = <&uart1_pins>;
214	status = "disabled";
215};
216
217&uart2 {
218	pinctrl-names = "default";
219	pinctrl-0 = <&uart2_pins>;
220	status = "disabled";
221};
222
223&usb_otg {
224	dr_mode = "otg";
225	status = "okay";
226};
227
228&usbphy {
229	/* USB Type-A ports' VBUS is always on */
230	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
231	usb0_vbus-supply = <&reg_usb0_vbus>;
232	status = "okay";
233};
234