xref: /linux/arch/arm/mm/proc-arm1022.S (revision d5859510d35d8e7d63fed5169f1775317f40fb03)
1/* SPDX-License-Identifier: GPL-2.0-or-later */
2/*
3 *  linux/arch/arm/mm/proc-arm1022.S: MMU functions for ARM1022E
4 *
5 *  Copyright (C) 2000 ARM Limited
6 *  Copyright (C) 2000 Deep Blue Solutions Ltd.
7 *  hacked for non-paged-MM by Hyok S. Choi, 2003.
8 *
9 * These are the low level assembler for performing cache and TLB
10 * functions on the ARM1022E.
11 */
12#include <linux/linkage.h>
13#include <linux/init.h>
14#include <linux/cfi_types.h>
15#include <linux/pgtable.h>
16#include <asm/assembler.h>
17#include <asm/asm-offsets.h>
18#include <asm/hwcap.h>
19#include <asm/pgtable-hwdef.h>
20#include <asm/ptrace.h>
21
22#include "proc-macros.S"
23
24/*
25 * This is the maximum size of an area which will be invalidated
26 * using the single invalidate entry instructions.  Anything larger
27 * than this, and we go for the whole cache.
28 *
29 * This value should be chosen such that we choose the cheapest
30 * alternative.
31 */
32#define MAX_AREA_SIZE	32768
33
34/*
35 * The size of one data cache line.
36 */
37#define CACHE_DLINESIZE	32
38
39/*
40 * The number of data cache segments.
41 */
42#define CACHE_DSEGMENTS	16
43
44/*
45 * The number of lines in a cache segment.
46 */
47#define CACHE_DENTRIES	64
48
49/*
50 * This is the size at which it becomes more efficient to
51 * clean the whole cache, rather than using the individual
52 * cache line maintenance instructions.
53 */
54#define CACHE_DLIMIT	32768
55
56	.text
57/*
58 * cpu_arm1022_proc_init()
59 */
60SYM_TYPED_FUNC_START(cpu_arm1022_proc_init)
61	ret	lr
62SYM_FUNC_END(cpu_arm1022_proc_init)
63
64/*
65 * cpu_arm1022_proc_fin()
66 */
67SYM_TYPED_FUNC_START(cpu_arm1022_proc_fin)
68	mrc	p15, 0, r0, c1, c0, 0		@ ctrl register
69	bic	r0, r0, #0x1000 		@ ...i............
70	bic	r0, r0, #0x000e 		@ ............wca.
71	mcr	p15, 0, r0, c1, c0, 0		@ disable caches
72	ret	lr
73SYM_FUNC_END(cpu_arm1022_proc_fin)
74
75/*
76 * cpu_arm1022_reset(loc)
77 *
78 * Perform a soft reset of the system.	Put the CPU into the
79 * same state as it would be if it had been reset, and branch
80 * to what would be the reset vector.
81 *
82 * loc: location to jump to for soft reset
83 */
84	.align	5
85	.pushsection	.idmap.text, "ax"
86SYM_TYPED_FUNC_START(cpu_arm1022_reset)
87	mov	ip, #0
88	mcr	p15, 0, ip, c7, c7, 0		@ invalidate I,D caches
89	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
90#ifdef CONFIG_MMU
91	mcr	p15, 0, ip, c8, c7, 0		@ invalidate I & D TLBs
92#endif
93	mrc	p15, 0, ip, c1, c0, 0		@ ctrl register
94	bic	ip, ip, #0x000f 		@ ............wcam
95	bic	ip, ip, #0x1100 		@ ...i...s........
96	mcr	p15, 0, ip, c1, c0, 0		@ ctrl register
97	ret	r0
98SYM_FUNC_END(cpu_arm1022_reset)
99	.popsection
100
101/*
102 * cpu_arm1022_do_idle()
103 */
104	.align	5
105SYM_TYPED_FUNC_START(cpu_arm1022_do_idle)
106	mcr	p15, 0, r0, c7, c0, 4		@ Wait for interrupt
107	ret	lr
108SYM_FUNC_END(cpu_arm1022_do_idle)
109
110/* ================================= CACHE ================================ */
111
112	.align	5
113
114/*
115 *	flush_icache_all()
116 *
117 *	Unconditionally clean and invalidate the entire icache.
118 */
119SYM_TYPED_FUNC_START(arm1022_flush_icache_all)
120#ifndef CONFIG_CPU_ICACHE_DISABLE
121	mov	r0, #0
122	mcr	p15, 0, r0, c7, c5, 0		@ invalidate I cache
123#endif
124	ret	lr
125SYM_FUNC_END(arm1022_flush_icache_all)
126
127/*
128 *	flush_user_cache_all()
129 *
130 *	Invalidate all cache entries in a particular address
131 *	space.
132 */
133SYM_FUNC_ALIAS(arm1022_flush_user_cache_all, arm1022_flush_kern_cache_all)
134
135/*
136 *	flush_kern_cache_all()
137 *
138 *	Clean and invalidate the entire cache.
139 */
140SYM_TYPED_FUNC_START(arm1022_flush_kern_cache_all)
141	mov	r2, #VM_EXEC
142	mov	ip, #0
143__flush_whole_cache:
144#ifndef CONFIG_CPU_DCACHE_DISABLE
145	mov	r1, #(CACHE_DSEGMENTS - 1) << 5	@ 16 segments
1461:	orr	r3, r1, #(CACHE_DENTRIES - 1) << 26 @ 64 entries
1472:	mcr	p15, 0, r3, c7, c14, 2		@ clean+invalidate D index
148	subs	r3, r3, #1 << 26
149	bcs	2b				@ entries 63 to 0
150	subs	r1, r1, #1 << 5
151	bcs	1b				@ segments 15 to 0
152#endif
153	tst	r2, #VM_EXEC
154#ifndef CONFIG_CPU_ICACHE_DISABLE
155	mcrne	p15, 0, ip, c7, c5, 0		@ invalidate I cache
156#endif
157	mcrne	p15, 0, ip, c7, c10, 4		@ drain WB
158	ret	lr
159SYM_FUNC_END(arm1022_flush_kern_cache_all)
160
161/*
162 *	flush_user_cache_range(start, end, flags)
163 *
164 *	Invalidate a range of cache entries in the specified
165 *	address space.
166 *
167 *	- start	- start address (inclusive)
168 *	- end	- end address (exclusive)
169 *	- flags	- vm_flags for this space
170 */
171SYM_TYPED_FUNC_START(arm1022_flush_user_cache_range)
172	mov	ip, #0
173	sub	r3, r1, r0			@ calculate total size
174	cmp	r3, #CACHE_DLIMIT
175	bhs	__flush_whole_cache
176
177#ifndef CONFIG_CPU_DCACHE_DISABLE
1781:	mcr	p15, 0, r0, c7, c14, 1		@ clean+invalidate D entry
179	add	r0, r0, #CACHE_DLINESIZE
180	cmp	r0, r1
181	blo	1b
182#endif
183	tst	r2, #VM_EXEC
184#ifndef CONFIG_CPU_ICACHE_DISABLE
185	mcrne	p15, 0, ip, c7, c5, 0		@ invalidate I cache
186#endif
187	mcrne	p15, 0, ip, c7, c10, 4		@ drain WB
188	ret	lr
189SYM_FUNC_END(arm1022_flush_user_cache_range)
190
191/*
192 *	coherent_kern_range(start, end)
193 *
194 *	Ensure coherency between the Icache and the Dcache in the
195 *	region described by start.  If you have non-snooping
196 *	Harvard caches, you need to implement this function.
197 *
198 *	- start	- virtual start address
199 *	- end	- virtual end address
200 */
201SYM_TYPED_FUNC_START(arm1022_coherent_kern_range)
202#ifdef CONFIG_CFI_CLANG /* Fallthrough if !CFI */
203	b	arm1022_coherent_user_range
204#endif
205SYM_FUNC_END(arm1022_coherent_kern_range)
206
207/*
208 *	coherent_user_range(start, end)
209 *
210 *	Ensure coherency between the Icache and the Dcache in the
211 *	region described by start.  If you have non-snooping
212 *	Harvard caches, you need to implement this function.
213 *
214 *	- start	- virtual start address
215 *	- end	- virtual end address
216 */
217SYM_TYPED_FUNC_START(arm1022_coherent_user_range)
218	mov	ip, #0
219	bic	r0, r0, #CACHE_DLINESIZE - 1
2201:
221#ifndef CONFIG_CPU_DCACHE_DISABLE
222	mcr	p15, 0, r0, c7, c10, 1		@ clean D entry
223#endif
224#ifndef CONFIG_CPU_ICACHE_DISABLE
225	mcr	p15, 0, r0, c7, c5, 1		@ invalidate I entry
226#endif
227	add	r0, r0, #CACHE_DLINESIZE
228	cmp	r0, r1
229	blo	1b
230	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
231	mov	r0, #0
232	ret	lr
233SYM_FUNC_END(arm1022_coherent_user_range)
234
235/*
236 *	flush_kern_dcache_area(void *addr, size_t size)
237 *
238 *	Ensure no D cache aliasing occurs, either with itself or
239 *	the I cache
240 *
241 *	- addr	- kernel address
242 *	- size	- region size
243 */
244SYM_TYPED_FUNC_START(arm1022_flush_kern_dcache_area)
245	mov	ip, #0
246#ifndef CONFIG_CPU_DCACHE_DISABLE
247	add	r1, r0, r1
2481:	mcr	p15, 0, r0, c7, c14, 1		@ clean+invalidate D entry
249	add	r0, r0, #CACHE_DLINESIZE
250	cmp	r0, r1
251	blo	1b
252#endif
253	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
254	ret	lr
255SYM_FUNC_END(arm1022_flush_kern_dcache_area)
256
257/*
258 *	dma_inv_range(start, end)
259 *
260 *	Invalidate (discard) the specified virtual address range.
261 *	May not write back any entries.  If 'start' or 'end'
262 *	are not cache line aligned, those lines must be written
263 *	back.
264 *
265 *	- start	- virtual start address
266 *	- end	- virtual end address
267 *
268 * (same as v4wb)
269 */
270arm1022_dma_inv_range:
271	mov	ip, #0
272#ifndef CONFIG_CPU_DCACHE_DISABLE
273	tst	r0, #CACHE_DLINESIZE - 1
274	bic	r0, r0, #CACHE_DLINESIZE - 1
275	mcrne	p15, 0, r0, c7, c10, 1		@ clean D entry
276	tst	r1, #CACHE_DLINESIZE - 1
277	mcrne	p15, 0, r1, c7, c10, 1		@ clean D entry
2781:	mcr	p15, 0, r0, c7, c6, 1		@ invalidate D entry
279	add	r0, r0, #CACHE_DLINESIZE
280	cmp	r0, r1
281	blo	1b
282#endif
283	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
284	ret	lr
285
286/*
287 *	dma_clean_range(start, end)
288 *
289 *	Clean the specified virtual address range.
290 *
291 *	- start	- virtual start address
292 *	- end	- virtual end address
293 *
294 * (same as v4wb)
295 */
296arm1022_dma_clean_range:
297	mov	ip, #0
298#ifndef CONFIG_CPU_DCACHE_DISABLE
299	bic	r0, r0, #CACHE_DLINESIZE - 1
3001:	mcr	p15, 0, r0, c7, c10, 1		@ clean D entry
301	add	r0, r0, #CACHE_DLINESIZE
302	cmp	r0, r1
303	blo	1b
304#endif
305	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
306	ret	lr
307
308/*
309 *	dma_flush_range(start, end)
310 *
311 *	Clean and invalidate the specified virtual address range.
312 *
313 *	- start	- virtual start address
314 *	- end	- virtual end address
315 */
316SYM_TYPED_FUNC_START(arm1022_dma_flush_range)
317	mov	ip, #0
318#ifndef CONFIG_CPU_DCACHE_DISABLE
319	bic	r0, r0, #CACHE_DLINESIZE - 1
3201:	mcr	p15, 0, r0, c7, c14, 1		@ clean+invalidate D entry
321	add	r0, r0, #CACHE_DLINESIZE
322	cmp	r0, r1
323	blo	1b
324#endif
325	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
326	ret	lr
327SYM_FUNC_END(arm1022_dma_flush_range)
328
329/*
330 *	dma_map_area(start, size, dir)
331 *	- start	- kernel virtual start address
332 *	- size	- size of region
333 *	- dir	- DMA direction
334 */
335SYM_TYPED_FUNC_START(arm1022_dma_map_area)
336	add	r1, r1, r0
337	cmp	r2, #DMA_TO_DEVICE
338	beq	arm1022_dma_clean_range
339	bcs	arm1022_dma_inv_range
340	b	arm1022_dma_flush_range
341SYM_FUNC_END(arm1022_dma_map_area)
342
343/*
344 *	dma_unmap_area(start, size, dir)
345 *	- start	- kernel virtual start address
346 *	- size	- size of region
347 *	- dir	- DMA direction
348 */
349SYM_TYPED_FUNC_START(arm1022_dma_unmap_area)
350	ret	lr
351SYM_FUNC_END(arm1022_dma_unmap_area)
352
353	.align	5
354SYM_TYPED_FUNC_START(cpu_arm1022_dcache_clean_area)
355#ifndef CONFIG_CPU_DCACHE_DISABLE
356	mov	ip, #0
3571:	mcr	p15, 0, r0, c7, c10, 1		@ clean D entry
358	add	r0, r0, #CACHE_DLINESIZE
359	subs	r1, r1, #CACHE_DLINESIZE
360	bhi	1b
361#endif
362	ret	lr
363SYM_FUNC_END(cpu_arm1022_dcache_clean_area)
364
365/* =============================== PageTable ============================== */
366
367/*
368 * cpu_arm1022_switch_mm(pgd)
369 *
370 * Set the translation base pointer to be as described by pgd.
371 *
372 * pgd: new page tables
373 */
374	.align	5
375SYM_TYPED_FUNC_START(cpu_arm1022_switch_mm)
376#ifdef CONFIG_MMU
377#ifndef CONFIG_CPU_DCACHE_DISABLE
378	mov	r1, #(CACHE_DSEGMENTS - 1) << 5	@ 16 segments
3791:	orr	r3, r1, #(CACHE_DENTRIES - 1) << 26 @ 64 entries
3802:	mcr	p15, 0, r3, c7, c14, 2		@ clean+invalidate D index
381	subs	r3, r3, #1 << 26
382	bcs	2b				@ entries 63 to 0
383	subs	r1, r1, #1 << 5
384	bcs	1b				@ segments 15 to 0
385#endif
386	mov	r1, #0
387#ifndef CONFIG_CPU_ICACHE_DISABLE
388	mcr	p15, 0, r1, c7, c5, 0		@ invalidate I cache
389#endif
390	mcr	p15, 0, r1, c7, c10, 4		@ drain WB
391	mcr	p15, 0, r0, c2, c0, 0		@ load page table pointer
392	mcr	p15, 0, r1, c8, c7, 0		@ invalidate I & D TLBs
393#endif
394	ret	lr
395SYM_FUNC_END(cpu_arm1022_switch_mm)
396
397/*
398 * cpu_arm1022_set_pte_ext(ptep, pte, ext)
399 *
400 * Set a PTE and flush it out
401 */
402	.align	5
403SYM_TYPED_FUNC_START(cpu_arm1022_set_pte_ext)
404#ifdef CONFIG_MMU
405	armv3_set_pte_ext
406	mov	r0, r0
407#ifndef CONFIG_CPU_DCACHE_DISABLE
408	mcr	p15, 0, r0, c7, c10, 1		@ clean D entry
409#endif
410#endif /* CONFIG_MMU */
411	ret	lr
412SYM_FUNC_END(cpu_arm1022_set_pte_ext)
413
414	.type	__arm1022_setup, #function
415__arm1022_setup:
416	mov	r0, #0
417	mcr	p15, 0, r0, c7, c7		@ invalidate I,D caches on v4
418	mcr	p15, 0, r0, c7, c10, 4		@ drain write buffer on v4
419#ifdef CONFIG_MMU
420	mcr	p15, 0, r0, c8, c7		@ invalidate I,D TLBs on v4
421#endif
422	adr	r5, arm1022_crval
423	ldmia	r5, {r5, r6}
424	mrc	p15, 0, r0, c1, c0		@ get control register v4
425	bic	r0, r0, r5
426	orr	r0, r0, r6
427#ifdef CONFIG_CPU_CACHE_ROUND_ROBIN
428	orr	r0, r0, #0x4000 		@ .R..............
429#endif
430	ret	lr
431	.size	__arm1022_setup, . - __arm1022_setup
432
433	/*
434	 *  R
435	 * .RVI ZFRS BLDP WCAM
436	 * .011 1001 ..11 0101
437	 *
438	 */
439	.type	arm1022_crval, #object
440arm1022_crval:
441	crval	clear=0x00007f3f, mmuset=0x00003935, ucset=0x00001930
442
443	__INITDATA
444	@ define struct processor (see <asm/proc-fns.h> and proc-macros.S)
445	define_processor_functions arm1022, dabort=v4t_early_abort, pabort=legacy_pabort
446
447	.section ".rodata"
448
449	string	cpu_arch_name, "armv5te"
450	string	cpu_elf_name, "v5"
451	string	cpu_arm1022_name, "ARM1022"
452
453	.align
454
455	.section ".proc.info.init", "a"
456
457	.type	__arm1022_proc_info,#object
458__arm1022_proc_info:
459	.long	0x4105a220			@ ARM 1022E (v5TE)
460	.long	0xff0ffff0
461	.long   PMD_TYPE_SECT | \
462		PMD_BIT4 | \
463		PMD_SECT_AP_WRITE | \
464		PMD_SECT_AP_READ
465	.long   PMD_TYPE_SECT | \
466		PMD_BIT4 | \
467		PMD_SECT_AP_WRITE | \
468		PMD_SECT_AP_READ
469	initfn	__arm1022_setup, __arm1022_proc_info
470	.long	cpu_arch_name
471	.long	cpu_elf_name
472	.long	HWCAP_SWP | HWCAP_HALF | HWCAP_THUMB | HWCAP_EDSP
473	.long	cpu_arm1022_name
474	.long	arm1022_processor_functions
475	.long	v4wbi_tlb_fns
476	.long	v4wb_user_fns
477	.long	arm1022_cache_fns
478	.size	__arm1022_proc_info, . - __arm1022_proc_info
479