1 /* 2 * Support for Sharp SL-Cxx00 Series of PDAs 3 * Models: SL-C3000 (Spitz), SL-C1000 (Akita) and SL-C3100 (Borzoi) 4 * 5 * Copyright (c) 2005 Richard Purdie 6 * 7 * Based on Sharp's 2.4 kernel patches/lubbock.c 8 * 9 * This program is free software; you can redistribute it and/or modify 10 * it under the terms of the GNU General Public License version 2 as 11 * published by the Free Software Foundation. 12 * 13 */ 14 15 #include <linux/kernel.h> 16 #include <linux/module.h> /* symbol_get ; symbol_put */ 17 #include <linux/platform_device.h> 18 #include <linux/delay.h> 19 #include <linux/gpio_keys.h> 20 #include <linux/gpio.h> 21 #include <linux/leds.h> 22 #include <linux/i2c.h> 23 #include <linux/i2c/pxa-i2c.h> 24 #include <linux/platform_data/pca953x.h> 25 #include <linux/spi/spi.h> 26 #include <linux/spi/ads7846.h> 27 #include <linux/spi/corgi_lcd.h> 28 #include <linux/spi/pxa2xx_spi.h> 29 #include <linux/mtd/sharpsl.h> 30 #include <linux/mtd/physmap.h> 31 #include <linux/input/matrix_keypad.h> 32 #include <linux/regulator/machine.h> 33 #include <linux/io.h> 34 #include <linux/module.h> 35 #include <linux/reboot.h> 36 #include <linux/memblock.h> 37 38 #include <asm/setup.h> 39 #include <asm/mach-types.h> 40 #include <asm/mach/arch.h> 41 #include <asm/mach/sharpsl_param.h> 42 #include <asm/hardware/scoop.h> 43 44 #include "pxa27x.h" 45 #include "pxa27x-udc.h" 46 #include <mach/reset.h> 47 #include <linux/platform_data/irda-pxaficp.h> 48 #include <linux/platform_data/mmc-pxamci.h> 49 #include <linux/platform_data/usb-ohci-pxa27x.h> 50 #include <linux/platform_data/video-pxafb.h> 51 #include <mach/spitz.h> 52 #include "sharpsl_pm.h" 53 #include <mach/smemc.h> 54 55 #include "generic.h" 56 #include "devices.h" 57 58 /****************************************************************************** 59 * Pin configuration 60 ******************************************************************************/ 61 static unsigned long spitz_pin_config[] __initdata = { 62 /* Chip Selects */ 63 GPIO78_nCS_2, /* SCOOP #2 */ 64 GPIO79_nCS_3, /* NAND */ 65 GPIO80_nCS_4, /* SCOOP #1 */ 66 67 /* LCD - 16bpp Active TFT */ 68 GPIOxx_LCD_TFT_16BPP, 69 70 /* PC Card */ 71 GPIO48_nPOE, 72 GPIO49_nPWE, 73 GPIO50_nPIOR, 74 GPIO51_nPIOW, 75 GPIO85_nPCE_1, 76 GPIO54_nPCE_2, 77 GPIO55_nPREG, 78 GPIO56_nPWAIT, 79 GPIO57_nIOIS16, 80 GPIO104_PSKTSEL, 81 82 /* I2S */ 83 GPIO28_I2S_BITCLK_OUT, 84 GPIO29_I2S_SDATA_IN, 85 GPIO30_I2S_SDATA_OUT, 86 GPIO31_I2S_SYNC, 87 88 /* MMC */ 89 GPIO32_MMC_CLK, 90 GPIO112_MMC_CMD, 91 GPIO92_MMC_DAT_0, 92 GPIO109_MMC_DAT_1, 93 GPIO110_MMC_DAT_2, 94 GPIO111_MMC_DAT_3, 95 96 /* GPIOs */ 97 GPIO9_GPIO, /* SPITZ_GPIO_nSD_DETECT */ 98 GPIO16_GPIO, /* SPITZ_GPIO_SYNC */ 99 GPIO81_GPIO, /* SPITZ_GPIO_nSD_WP */ 100 GPIO41_GPIO, /* SPITZ_GPIO_USB_CONNECT */ 101 GPIO37_GPIO, /* SPITZ_GPIO_USB_HOST */ 102 GPIO35_GPIO, /* SPITZ_GPIO_USB_DEVICE */ 103 GPIO22_GPIO, /* SPITZ_GPIO_HSYNC */ 104 GPIO94_GPIO, /* SPITZ_GPIO_CF_CD */ 105 GPIO105_GPIO, /* SPITZ_GPIO_CF_IRQ */ 106 GPIO106_GPIO, /* SPITZ_GPIO_CF2_IRQ */ 107 108 /* GPIO matrix keypad */ 109 GPIO88_GPIO, /* column 0 */ 110 GPIO23_GPIO, /* column 1 */ 111 GPIO24_GPIO, /* column 2 */ 112 GPIO25_GPIO, /* column 3 */ 113 GPIO26_GPIO, /* column 4 */ 114 GPIO27_GPIO, /* column 5 */ 115 GPIO52_GPIO, /* column 6 */ 116 GPIO103_GPIO, /* column 7 */ 117 GPIO107_GPIO, /* column 8 */ 118 GPIO108_GPIO, /* column 9 */ 119 GPIO114_GPIO, /* column 10 */ 120 GPIO12_GPIO, /* row 0 */ 121 GPIO17_GPIO, /* row 1 */ 122 GPIO91_GPIO, /* row 2 */ 123 GPIO34_GPIO, /* row 3 */ 124 GPIO36_GPIO, /* row 4 */ 125 GPIO38_GPIO, /* row 5 */ 126 GPIO39_GPIO, /* row 6 */ 127 128 /* I2C */ 129 GPIO117_I2C_SCL, 130 GPIO118_I2C_SDA, 131 132 GPIO0_GPIO | WAKEUP_ON_EDGE_RISE, /* SPITZ_GPIO_KEY_INT */ 133 GPIO1_GPIO | WAKEUP_ON_EDGE_FALL, /* SPITZ_GPIO_RESET */ 134 }; 135 136 137 /****************************************************************************** 138 * Scoop GPIO expander 139 ******************************************************************************/ 140 #if defined(CONFIG_SHARP_SCOOP) || defined(CONFIG_SHARP_SCOOP_MODULE) 141 /* SCOOP Device #1 */ 142 static struct resource spitz_scoop_1_resources[] = { 143 [0] = { 144 .start = 0x10800000, 145 .end = 0x10800fff, 146 .flags = IORESOURCE_MEM, 147 }, 148 }; 149 150 static struct scoop_config spitz_scoop_1_setup = { 151 .io_dir = SPITZ_SCP_IO_DIR, 152 .io_out = SPITZ_SCP_IO_OUT, 153 .suspend_clr = SPITZ_SCP_SUS_CLR, 154 .suspend_set = SPITZ_SCP_SUS_SET, 155 .gpio_base = SPITZ_SCP_GPIO_BASE, 156 }; 157 158 struct platform_device spitz_scoop_1_device = { 159 .name = "sharp-scoop", 160 .id = 0, 161 .dev = { 162 .platform_data = &spitz_scoop_1_setup, 163 }, 164 .num_resources = ARRAY_SIZE(spitz_scoop_1_resources), 165 .resource = spitz_scoop_1_resources, 166 }; 167 168 /* SCOOP Device #2 */ 169 static struct resource spitz_scoop_2_resources[] = { 170 [0] = { 171 .start = 0x08800040, 172 .end = 0x08800fff, 173 .flags = IORESOURCE_MEM, 174 }, 175 }; 176 177 static struct scoop_config spitz_scoop_2_setup = { 178 .io_dir = SPITZ_SCP2_IO_DIR, 179 .io_out = SPITZ_SCP2_IO_OUT, 180 .suspend_clr = SPITZ_SCP2_SUS_CLR, 181 .suspend_set = SPITZ_SCP2_SUS_SET, 182 .gpio_base = SPITZ_SCP2_GPIO_BASE, 183 }; 184 185 struct platform_device spitz_scoop_2_device = { 186 .name = "sharp-scoop", 187 .id = 1, 188 .dev = { 189 .platform_data = &spitz_scoop_2_setup, 190 }, 191 .num_resources = ARRAY_SIZE(spitz_scoop_2_resources), 192 .resource = spitz_scoop_2_resources, 193 }; 194 195 static void __init spitz_scoop_init(void) 196 { 197 platform_device_register(&spitz_scoop_1_device); 198 199 /* Akita doesn't have the second SCOOP chip */ 200 if (!machine_is_akita()) 201 platform_device_register(&spitz_scoop_2_device); 202 } 203 204 /* Power control is shared with between one of the CF slots and SD */ 205 static void __maybe_unused spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr) 206 { 207 unsigned short cpr; 208 unsigned long flags; 209 210 if (new_cpr & 0x7) { 211 gpio_set_value(SPITZ_GPIO_CF_POWER, 1); 212 mdelay(5); 213 } 214 215 local_irq_save(flags); 216 217 cpr = read_scoop_reg(&spitz_scoop_1_device.dev, SCOOP_CPR); 218 219 if (enable & new_cpr) 220 cpr |= new_cpr; 221 else 222 cpr &= ~enable; 223 224 write_scoop_reg(&spitz_scoop_1_device.dev, SCOOP_CPR, cpr); 225 226 local_irq_restore(flags); 227 228 if (!(cpr & 0x7)) { 229 mdelay(1); 230 gpio_set_value(SPITZ_GPIO_CF_POWER, 0); 231 } 232 } 233 234 #else 235 static inline void spitz_scoop_init(void) {} 236 static inline void spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr) {} 237 #endif 238 239 /****************************************************************************** 240 * PCMCIA 241 ******************************************************************************/ 242 #if defined(CONFIG_PCMCIA_PXA2XX) || defined(CONFIG_PCMCIA_PXA2XX_MODULE) 243 static void spitz_pcmcia_pwr(struct device *scoop, uint16_t cpr, int nr) 244 { 245 /* Only need to override behaviour for slot 0 */ 246 if (nr == 0) 247 spitz_card_pwr_ctrl( 248 cpr & (SCOOP_CPR_CF_3V | SCOOP_CPR_CF_XV), cpr); 249 else 250 write_scoop_reg(scoop, SCOOP_CPR, cpr); 251 } 252 253 static struct scoop_pcmcia_dev spitz_pcmcia_scoop[] = { 254 { 255 .dev = &spitz_scoop_1_device.dev, 256 .irq = SPITZ_IRQ_GPIO_CF_IRQ, 257 .cd_irq = SPITZ_IRQ_GPIO_CF_CD, 258 .cd_irq_str = "PCMCIA0 CD", 259 }, { 260 .dev = &spitz_scoop_2_device.dev, 261 .irq = SPITZ_IRQ_GPIO_CF2_IRQ, 262 .cd_irq = -1, 263 }, 264 }; 265 266 static struct scoop_pcmcia_config spitz_pcmcia_config = { 267 .devs = &spitz_pcmcia_scoop[0], 268 .num_devs = 2, 269 .power_ctrl = spitz_pcmcia_pwr, 270 }; 271 272 static void __init spitz_pcmcia_init(void) 273 { 274 /* Akita has only one PCMCIA slot used */ 275 if (machine_is_akita()) 276 spitz_pcmcia_config.num_devs = 1; 277 278 platform_scoop_config = &spitz_pcmcia_config; 279 } 280 #else 281 static inline void spitz_pcmcia_init(void) {} 282 #endif 283 284 /****************************************************************************** 285 * GPIO keyboard 286 ******************************************************************************/ 287 #if defined(CONFIG_KEYBOARD_MATRIX) || defined(CONFIG_KEYBOARD_MATRIX_MODULE) 288 289 #define SPITZ_KEY_CALENDAR KEY_F1 290 #define SPITZ_KEY_ADDRESS KEY_F2 291 #define SPITZ_KEY_FN KEY_F3 292 #define SPITZ_KEY_CANCEL KEY_F4 293 #define SPITZ_KEY_EXOK KEY_F5 294 #define SPITZ_KEY_EXCANCEL KEY_F6 295 #define SPITZ_KEY_EXJOGDOWN KEY_F7 296 #define SPITZ_KEY_EXJOGUP KEY_F8 297 #define SPITZ_KEY_JAP1 KEY_LEFTALT 298 #define SPITZ_KEY_JAP2 KEY_RIGHTCTRL 299 #define SPITZ_KEY_SYNC KEY_F9 300 #define SPITZ_KEY_MAIL KEY_F10 301 #define SPITZ_KEY_OK KEY_F11 302 #define SPITZ_KEY_MENU KEY_F12 303 304 static const uint32_t spitz_keymap[] = { 305 KEY(0, 0, KEY_LEFTCTRL), 306 KEY(0, 1, KEY_1), 307 KEY(0, 2, KEY_3), 308 KEY(0, 3, KEY_5), 309 KEY(0, 4, KEY_6), 310 KEY(0, 5, KEY_7), 311 KEY(0, 6, KEY_9), 312 KEY(0, 7, KEY_0), 313 KEY(0, 8, KEY_BACKSPACE), 314 KEY(0, 9, SPITZ_KEY_EXOK), /* EXOK */ 315 KEY(0, 10, SPITZ_KEY_EXCANCEL), /* EXCANCEL */ 316 KEY(1, 1, KEY_2), 317 KEY(1, 2, KEY_4), 318 KEY(1, 3, KEY_R), 319 KEY(1, 4, KEY_Y), 320 KEY(1, 5, KEY_8), 321 KEY(1, 6, KEY_I), 322 KEY(1, 7, KEY_O), 323 KEY(1, 8, KEY_P), 324 KEY(1, 9, SPITZ_KEY_EXJOGDOWN), /* EXJOGDOWN */ 325 KEY(1, 10, SPITZ_KEY_EXJOGUP), /* EXJOGUP */ 326 KEY(2, 0, KEY_TAB), 327 KEY(2, 1, KEY_Q), 328 KEY(2, 2, KEY_E), 329 KEY(2, 3, KEY_T), 330 KEY(2, 4, KEY_G), 331 KEY(2, 5, KEY_U), 332 KEY(2, 6, KEY_J), 333 KEY(2, 7, KEY_K), 334 KEY(3, 0, SPITZ_KEY_ADDRESS), /* ADDRESS */ 335 KEY(3, 1, KEY_W), 336 KEY(3, 2, KEY_S), 337 KEY(3, 3, KEY_F), 338 KEY(3, 4, KEY_V), 339 KEY(3, 5, KEY_H), 340 KEY(3, 6, KEY_M), 341 KEY(3, 7, KEY_L), 342 KEY(3, 9, KEY_RIGHTSHIFT), 343 KEY(4, 0, SPITZ_KEY_CALENDAR), /* CALENDAR */ 344 KEY(4, 1, KEY_A), 345 KEY(4, 2, KEY_D), 346 KEY(4, 3, KEY_C), 347 KEY(4, 4, KEY_B), 348 KEY(4, 5, KEY_N), 349 KEY(4, 6, KEY_DOT), 350 KEY(4, 8, KEY_ENTER), 351 KEY(4, 9, KEY_LEFTSHIFT), 352 KEY(5, 0, SPITZ_KEY_MAIL), /* MAIL */ 353 KEY(5, 1, KEY_Z), 354 KEY(5, 2, KEY_X), 355 KEY(5, 3, KEY_MINUS), 356 KEY(5, 4, KEY_SPACE), 357 KEY(5, 5, KEY_COMMA), 358 KEY(5, 7, KEY_UP), 359 KEY(5, 10, SPITZ_KEY_FN), /* FN */ 360 KEY(6, 0, KEY_SYSRQ), 361 KEY(6, 1, SPITZ_KEY_JAP1), /* JAP1 */ 362 KEY(6, 2, SPITZ_KEY_JAP2), /* JAP2 */ 363 KEY(6, 3, SPITZ_KEY_CANCEL), /* CANCEL */ 364 KEY(6, 4, SPITZ_KEY_OK), /* OK */ 365 KEY(6, 5, SPITZ_KEY_MENU), /* MENU */ 366 KEY(6, 6, KEY_LEFT), 367 KEY(6, 7, KEY_DOWN), 368 KEY(6, 8, KEY_RIGHT), 369 }; 370 371 static const struct matrix_keymap_data spitz_keymap_data = { 372 .keymap = spitz_keymap, 373 .keymap_size = ARRAY_SIZE(spitz_keymap), 374 }; 375 376 static const uint32_t spitz_row_gpios[] = 377 { 12, 17, 91, 34, 36, 38, 39 }; 378 static const uint32_t spitz_col_gpios[] = 379 { 88, 23, 24, 25, 26, 27, 52, 103, 107, 108, 114 }; 380 381 static struct matrix_keypad_platform_data spitz_mkp_pdata = { 382 .keymap_data = &spitz_keymap_data, 383 .row_gpios = spitz_row_gpios, 384 .col_gpios = spitz_col_gpios, 385 .num_row_gpios = ARRAY_SIZE(spitz_row_gpios), 386 .num_col_gpios = ARRAY_SIZE(spitz_col_gpios), 387 .col_scan_delay_us = 10, 388 .debounce_ms = 10, 389 .wakeup = 1, 390 }; 391 392 static struct platform_device spitz_mkp_device = { 393 .name = "matrix-keypad", 394 .id = -1, 395 .dev = { 396 .platform_data = &spitz_mkp_pdata, 397 }, 398 }; 399 400 static void __init spitz_mkp_init(void) 401 { 402 platform_device_register(&spitz_mkp_device); 403 } 404 #else 405 static inline void spitz_mkp_init(void) {} 406 #endif 407 408 /****************************************************************************** 409 * GPIO keys 410 ******************************************************************************/ 411 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) 412 static struct gpio_keys_button spitz_gpio_keys[] = { 413 { 414 .type = EV_PWR, 415 .code = KEY_SUSPEND, 416 .gpio = SPITZ_GPIO_ON_KEY, 417 .desc = "On Off", 418 .wakeup = 1, 419 }, 420 /* Two buttons detecting the lid state */ 421 { 422 .type = EV_SW, 423 .code = 0, 424 .gpio = SPITZ_GPIO_SWA, 425 .desc = "Display Down", 426 }, 427 { 428 .type = EV_SW, 429 .code = 1, 430 .gpio = SPITZ_GPIO_SWB, 431 .desc = "Lid Closed", 432 }, 433 }; 434 435 static struct gpio_keys_platform_data spitz_gpio_keys_platform_data = { 436 .buttons = spitz_gpio_keys, 437 .nbuttons = ARRAY_SIZE(spitz_gpio_keys), 438 }; 439 440 static struct platform_device spitz_gpio_keys_device = { 441 .name = "gpio-keys", 442 .id = -1, 443 .dev = { 444 .platform_data = &spitz_gpio_keys_platform_data, 445 }, 446 }; 447 448 static void __init spitz_keys_init(void) 449 { 450 platform_device_register(&spitz_gpio_keys_device); 451 } 452 #else 453 static inline void spitz_keys_init(void) {} 454 #endif 455 456 /****************************************************************************** 457 * LEDs 458 ******************************************************************************/ 459 #if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE) 460 static struct gpio_led spitz_gpio_leds[] = { 461 { 462 .name = "spitz:amber:charge", 463 .default_trigger = "sharpsl-charge", 464 .gpio = SPITZ_GPIO_LED_ORANGE, 465 }, 466 { 467 .name = "spitz:green:hddactivity", 468 .default_trigger = "disk-activity", 469 .gpio = SPITZ_GPIO_LED_GREEN, 470 }, 471 }; 472 473 static struct gpio_led_platform_data spitz_gpio_leds_info = { 474 .leds = spitz_gpio_leds, 475 .num_leds = ARRAY_SIZE(spitz_gpio_leds), 476 }; 477 478 static struct platform_device spitz_led_device = { 479 .name = "leds-gpio", 480 .id = -1, 481 .dev = { 482 .platform_data = &spitz_gpio_leds_info, 483 }, 484 }; 485 486 static void __init spitz_leds_init(void) 487 { 488 platform_device_register(&spitz_led_device); 489 } 490 #else 491 static inline void spitz_leds_init(void) {} 492 #endif 493 494 /****************************************************************************** 495 * SSP Devices 496 ******************************************************************************/ 497 #if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE) 498 static void spitz_ads7846_wait_for_hsync(void) 499 { 500 while (gpio_get_value(SPITZ_GPIO_HSYNC)) 501 cpu_relax(); 502 503 while (!gpio_get_value(SPITZ_GPIO_HSYNC)) 504 cpu_relax(); 505 } 506 507 static struct ads7846_platform_data spitz_ads7846_info = { 508 .model = 7846, 509 .vref_delay_usecs = 100, 510 .x_plate_ohms = 419, 511 .y_plate_ohms = 486, 512 .pressure_max = 1024, 513 .gpio_pendown = SPITZ_GPIO_TP_INT, 514 .wait_for_sync = spitz_ads7846_wait_for_hsync, 515 }; 516 517 static struct pxa2xx_spi_chip spitz_ads7846_chip = { 518 .gpio_cs = SPITZ_GPIO_ADS7846_CS, 519 }; 520 521 static void spitz_bl_kick_battery(void) 522 { 523 void (*kick_batt)(void); 524 525 kick_batt = symbol_get(sharpsl_battery_kick); 526 if (kick_batt) { 527 kick_batt(); 528 symbol_put(sharpsl_battery_kick); 529 } 530 } 531 532 static struct corgi_lcd_platform_data spitz_lcdcon_info = { 533 .init_mode = CORGI_LCD_MODE_VGA, 534 .max_intensity = 0x2f, 535 .default_intensity = 0x1f, 536 .limit_mask = 0x0b, 537 .gpio_backlight_cont = SPITZ_GPIO_BACKLIGHT_CONT, 538 .gpio_backlight_on = SPITZ_GPIO_BACKLIGHT_ON, 539 .kick_battery = spitz_bl_kick_battery, 540 }; 541 542 static struct pxa2xx_spi_chip spitz_lcdcon_chip = { 543 .gpio_cs = SPITZ_GPIO_LCDCON_CS, 544 }; 545 546 static struct pxa2xx_spi_chip spitz_max1111_chip = { 547 .gpio_cs = SPITZ_GPIO_MAX1111_CS, 548 }; 549 550 static struct spi_board_info spitz_spi_devices[] = { 551 { 552 .modalias = "ads7846", 553 .max_speed_hz = 1200000, 554 .bus_num = 2, 555 .chip_select = 0, 556 .platform_data = &spitz_ads7846_info, 557 .controller_data = &spitz_ads7846_chip, 558 .irq = PXA_GPIO_TO_IRQ(SPITZ_GPIO_TP_INT), 559 }, { 560 .modalias = "corgi-lcd", 561 .max_speed_hz = 50000, 562 .bus_num = 2, 563 .chip_select = 1, 564 .platform_data = &spitz_lcdcon_info, 565 .controller_data = &spitz_lcdcon_chip, 566 }, { 567 .modalias = "max1111", 568 .max_speed_hz = 450000, 569 .bus_num = 2, 570 .chip_select = 2, 571 .controller_data = &spitz_max1111_chip, 572 }, 573 }; 574 575 static struct pxa2xx_spi_master spitz_spi_info = { 576 .num_chipselect = 3, 577 }; 578 579 static void __init spitz_spi_init(void) 580 { 581 struct corgi_lcd_platform_data *lcd_data = &spitz_lcdcon_info; 582 583 if (machine_is_akita()) { 584 lcd_data->gpio_backlight_cont = AKITA_GPIO_BACKLIGHT_CONT; 585 lcd_data->gpio_backlight_on = AKITA_GPIO_BACKLIGHT_ON; 586 } 587 588 pxa2xx_set_spi_info(2, &spitz_spi_info); 589 spi_register_board_info(ARRAY_AND_SIZE(spitz_spi_devices)); 590 } 591 #else 592 static inline void spitz_spi_init(void) {} 593 #endif 594 595 /****************************************************************************** 596 * SD/MMC card controller 597 ******************************************************************************/ 598 #if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE) 599 /* 600 * NOTE: The card detect interrupt isn't debounced so we delay it by 250ms to 601 * give the card a chance to fully insert/eject. 602 */ 603 static int spitz_mci_setpower(struct device *dev, unsigned int vdd) 604 { 605 struct pxamci_platform_data* p_d = dev->platform_data; 606 607 if ((1 << vdd) & p_d->ocr_mask) 608 spitz_card_pwr_ctrl(SCOOP_CPR_SD_3V, SCOOP_CPR_SD_3V); 609 else 610 spitz_card_pwr_ctrl(SCOOP_CPR_SD_3V, 0x0); 611 612 return 0; 613 } 614 615 static struct pxamci_platform_data spitz_mci_platform_data = { 616 .detect_delay_ms = 250, 617 .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34, 618 .setpower = spitz_mci_setpower, 619 .gpio_card_detect = SPITZ_GPIO_nSD_DETECT, 620 .gpio_card_ro = SPITZ_GPIO_nSD_WP, 621 .gpio_power = -1, 622 }; 623 624 static void __init spitz_mmc_init(void) 625 { 626 pxa_set_mci_info(&spitz_mci_platform_data); 627 } 628 #else 629 static inline void spitz_mmc_init(void) {} 630 #endif 631 632 /****************************************************************************** 633 * USB Host 634 ******************************************************************************/ 635 #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) 636 static int spitz_ohci_init(struct device *dev) 637 { 638 int err; 639 640 err = gpio_request(SPITZ_GPIO_USB_HOST, "USB_HOST"); 641 if (err) 642 return err; 643 644 /* Only Port 2 is connected, setup USB Port 2 Output Control Register */ 645 UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE; 646 647 return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1); 648 } 649 650 static void spitz_ohci_exit(struct device *dev) 651 { 652 gpio_free(SPITZ_GPIO_USB_HOST); 653 } 654 655 static struct pxaohci_platform_data spitz_ohci_platform_data = { 656 .port_mode = PMM_NPS_MODE, 657 .init = spitz_ohci_init, 658 .exit = spitz_ohci_exit, 659 .flags = ENABLE_PORT_ALL | NO_OC_PROTECTION, 660 .power_budget = 150, 661 }; 662 663 static void __init spitz_uhc_init(void) 664 { 665 pxa_set_ohci_info(&spitz_ohci_platform_data); 666 } 667 #else 668 static inline void spitz_uhc_init(void) {} 669 #endif 670 671 /****************************************************************************** 672 * IrDA 673 ******************************************************************************/ 674 #if defined(CONFIG_PXA_FICP) || defined(CONFIG_PXA_FICP_MODULE) 675 static struct pxaficp_platform_data spitz_ficp_platform_data = { 676 .transceiver_cap = IR_SIRMODE | IR_OFF, 677 }; 678 679 static void __init spitz_irda_init(void) 680 { 681 if (machine_is_akita()) 682 spitz_ficp_platform_data.gpio_pwdown = AKITA_GPIO_IR_ON; 683 else 684 spitz_ficp_platform_data.gpio_pwdown = SPITZ_GPIO_IR_ON; 685 686 pxa_set_ficp_info(&spitz_ficp_platform_data); 687 } 688 #else 689 static inline void spitz_irda_init(void) {} 690 #endif 691 692 /****************************************************************************** 693 * Framebuffer 694 ******************************************************************************/ 695 #if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) 696 static struct pxafb_mode_info spitz_pxafb_modes[] = { 697 { 698 .pixclock = 19231, 699 .xres = 480, 700 .yres = 640, 701 .bpp = 16, 702 .hsync_len = 40, 703 .left_margin = 46, 704 .right_margin = 125, 705 .vsync_len = 3, 706 .upper_margin = 1, 707 .lower_margin = 0, 708 .sync = 0, 709 }, { 710 .pixclock = 134617, 711 .xres = 240, 712 .yres = 320, 713 .bpp = 16, 714 .hsync_len = 20, 715 .left_margin = 20, 716 .right_margin = 46, 717 .vsync_len = 2, 718 .upper_margin = 1, 719 .lower_margin = 0, 720 .sync = 0, 721 }, 722 }; 723 724 static struct pxafb_mach_info spitz_pxafb_info = { 725 .modes = spitz_pxafb_modes, 726 .num_modes = ARRAY_SIZE(spitz_pxafb_modes), 727 .fixed_modes = 1, 728 .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_ALTERNATE_MAPPING, 729 }; 730 731 static void __init spitz_lcd_init(void) 732 { 733 pxa_set_fb_info(NULL, &spitz_pxafb_info); 734 } 735 #else 736 static inline void spitz_lcd_init(void) {} 737 #endif 738 739 /****************************************************************************** 740 * NAND Flash 741 ******************************************************************************/ 742 #if defined(CONFIG_MTD_NAND_SHARPSL) || defined(CONFIG_MTD_NAND_SHARPSL_MODULE) 743 static struct mtd_partition spitz_nand_partitions[] = { 744 { 745 .name = "System Area", 746 .offset = 0, 747 .size = 7 * 1024 * 1024, 748 }, { 749 .name = "Root Filesystem", 750 .offset = 7 * 1024 * 1024, 751 }, { 752 .name = "Home Filesystem", 753 .offset = MTDPART_OFS_APPEND, 754 .size = MTDPART_SIZ_FULL, 755 }, 756 }; 757 758 static uint8_t scan_ff_pattern[] = { 0xff, 0xff }; 759 760 static struct nand_bbt_descr spitz_nand_bbt = { 761 .options = 0, 762 .offs = 4, 763 .len = 2, 764 .pattern = scan_ff_pattern 765 }; 766 767 static int akita_ooblayout_ecc(struct mtd_info *mtd, int section, 768 struct mtd_oob_region *oobregion) 769 { 770 if (section > 12) 771 return -ERANGE; 772 773 switch (section % 3) { 774 case 0: 775 oobregion->offset = 5; 776 oobregion->length = 1; 777 break; 778 779 case 1: 780 oobregion->offset = 1; 781 oobregion->length = 3; 782 break; 783 784 case 2: 785 oobregion->offset = 6; 786 oobregion->length = 2; 787 break; 788 } 789 790 oobregion->offset += (section / 3) * 0x10; 791 792 return 0; 793 } 794 795 static int akita_ooblayout_free(struct mtd_info *mtd, int section, 796 struct mtd_oob_region *oobregion) 797 { 798 if (section) 799 return -ERANGE; 800 801 oobregion->offset = 8; 802 oobregion->length = 9; 803 804 return 0; 805 } 806 807 static const struct mtd_ooblayout_ops akita_ooblayout_ops = { 808 .ecc = akita_ooblayout_ecc, 809 .free = akita_ooblayout_free, 810 }; 811 812 static struct sharpsl_nand_platform_data spitz_nand_pdata = { 813 .badblock_pattern = &spitz_nand_bbt, 814 .partitions = spitz_nand_partitions, 815 .nr_partitions = ARRAY_SIZE(spitz_nand_partitions), 816 }; 817 818 static struct resource spitz_nand_resources[] = { 819 { 820 .start = PXA_CS3_PHYS, 821 .end = PXA_CS3_PHYS + SZ_4K - 1, 822 .flags = IORESOURCE_MEM, 823 }, 824 }; 825 826 static struct platform_device spitz_nand_device = { 827 .name = "sharpsl-nand", 828 .id = -1, 829 .resource = spitz_nand_resources, 830 .num_resources = ARRAY_SIZE(spitz_nand_resources), 831 .dev = { 832 .platform_data = &spitz_nand_pdata, 833 } 834 }; 835 836 static void __init spitz_nand_init(void) 837 { 838 if (machine_is_spitz()) { 839 spitz_nand_partitions[1].size = 5 * 1024 * 1024; 840 } else if (machine_is_akita()) { 841 spitz_nand_partitions[1].size = 58 * 1024 * 1024; 842 spitz_nand_bbt.len = 1; 843 spitz_nand_pdata.ecc_layout = &akita_ooblayout_ops; 844 } else if (machine_is_borzoi()) { 845 spitz_nand_partitions[1].size = 32 * 1024 * 1024; 846 spitz_nand_bbt.len = 1; 847 spitz_nand_pdata.ecc_layout = &akita_ooblayout_ops; 848 } 849 850 platform_device_register(&spitz_nand_device); 851 } 852 #else 853 static inline void spitz_nand_init(void) {} 854 #endif 855 856 /****************************************************************************** 857 * NOR Flash 858 ******************************************************************************/ 859 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) 860 static struct mtd_partition spitz_rom_parts[] = { 861 { 862 .name ="Boot PROM Filesystem", 863 .offset = 0x00140000, 864 .size = MTDPART_SIZ_FULL, 865 }, 866 }; 867 868 static struct physmap_flash_data spitz_rom_data = { 869 .width = 2, 870 .nr_parts = ARRAY_SIZE(spitz_rom_parts), 871 .parts = spitz_rom_parts, 872 }; 873 874 static struct resource spitz_rom_resources[] = { 875 { 876 .start = PXA_CS0_PHYS, 877 .end = PXA_CS0_PHYS + SZ_8M - 1, 878 .flags = IORESOURCE_MEM, 879 }, 880 }; 881 882 static struct platform_device spitz_rom_device = { 883 .name = "physmap-flash", 884 .id = -1, 885 .resource = spitz_rom_resources, 886 .num_resources = ARRAY_SIZE(spitz_rom_resources), 887 .dev = { 888 .platform_data = &spitz_rom_data, 889 }, 890 }; 891 892 static void __init spitz_nor_init(void) 893 { 894 platform_device_register(&spitz_rom_device); 895 } 896 #else 897 static inline void spitz_nor_init(void) {} 898 #endif 899 900 /****************************************************************************** 901 * I2C devices 902 ******************************************************************************/ 903 #if defined(CONFIG_I2C_PXA) || defined(CONFIG_I2C_PXA_MODULE) 904 static struct pca953x_platform_data akita_pca953x_pdata = { 905 .gpio_base = AKITA_IOEXP_GPIO_BASE, 906 }; 907 908 static struct i2c_board_info spitz_i2c_devs[] = { 909 { 910 .type = "wm8750", 911 .addr = 0x1b, 912 }, { 913 .type = "max7310", 914 .addr = 0x18, 915 .platform_data = &akita_pca953x_pdata, 916 }, 917 }; 918 919 static struct regulator_consumer_supply isl6271a_consumers[] = { 920 REGULATOR_SUPPLY("vcc_core", NULL), 921 }; 922 923 static struct regulator_init_data isl6271a_info[] = { 924 { 925 .constraints = { 926 .name = "vcc_core range", 927 .min_uV = 850000, 928 .max_uV = 1600000, 929 .always_on = 1, 930 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE, 931 }, 932 .consumer_supplies = isl6271a_consumers, 933 .num_consumer_supplies = ARRAY_SIZE(isl6271a_consumers), 934 } 935 }; 936 937 static struct i2c_board_info spitz_pi2c_devs[] = { 938 { 939 .type = "isl6271a", 940 .addr = 0x0c, 941 .platform_data = &isl6271a_info, 942 }, 943 }; 944 945 static void __init spitz_i2c_init(void) 946 { 947 int size = ARRAY_SIZE(spitz_i2c_devs); 948 949 /* Only Akita has the max7310 chip */ 950 if (!machine_is_akita()) 951 size--; 952 953 pxa_set_i2c_info(NULL); 954 pxa27x_set_i2c_power_info(NULL); 955 i2c_register_board_info(0, spitz_i2c_devs, size); 956 i2c_register_board_info(1, ARRAY_AND_SIZE(spitz_pi2c_devs)); 957 } 958 #else 959 static inline void spitz_i2c_init(void) {} 960 #endif 961 962 /****************************************************************************** 963 * Audio devices 964 ******************************************************************************/ 965 static inline void spitz_audio_init(void) 966 { 967 platform_device_register_simple("spitz-audio", -1, NULL, 0); 968 } 969 970 /****************************************************************************** 971 * Machine init 972 ******************************************************************************/ 973 static void spitz_poweroff(void) 974 { 975 pxa_restart(REBOOT_GPIO, NULL); 976 } 977 978 static void spitz_restart(enum reboot_mode mode, const char *cmd) 979 { 980 uint32_t msc0 = __raw_readl(MSC0); 981 /* Bootloader magic for a reboot */ 982 if ((msc0 & 0xffff0000) == 0x7ff00000) 983 __raw_writel((msc0 & 0xffff) | 0x7ee00000, MSC0); 984 985 spitz_poweroff(); 986 } 987 988 static void __init spitz_init(void) 989 { 990 init_gpio_reset(SPITZ_GPIO_ON_RESET, 1, 0); 991 pm_power_off = spitz_poweroff; 992 993 PMCR = 0x00; 994 995 /* Stop 3.6MHz and drive HIGH to PCMCIA and CS */ 996 PCFR |= PCFR_OPDE; 997 998 pxa2xx_mfp_config(ARRAY_AND_SIZE(spitz_pin_config)); 999 1000 pxa_set_ffuart_info(NULL); 1001 pxa_set_btuart_info(NULL); 1002 pxa_set_stuart_info(NULL); 1003 1004 spitz_spi_init(); 1005 spitz_scoop_init(); 1006 spitz_mkp_init(); 1007 spitz_keys_init(); 1008 spitz_leds_init(); 1009 spitz_mmc_init(); 1010 spitz_pcmcia_init(); 1011 spitz_irda_init(); 1012 spitz_uhc_init(); 1013 spitz_lcd_init(); 1014 spitz_nor_init(); 1015 spitz_nand_init(); 1016 spitz_i2c_init(); 1017 spitz_audio_init(); 1018 1019 regulator_has_full_constraints(); 1020 } 1021 1022 static void __init spitz_fixup(struct tag *tags, char **cmdline) 1023 { 1024 sharpsl_save_param(); 1025 memblock_add(0xa0000000, SZ_64M); 1026 } 1027 1028 #ifdef CONFIG_MACH_SPITZ 1029 MACHINE_START(SPITZ, "SHARP Spitz") 1030 .fixup = spitz_fixup, 1031 .map_io = pxa27x_map_io, 1032 .nr_irqs = PXA_NR_IRQS, 1033 .init_irq = pxa27x_init_irq, 1034 .handle_irq = pxa27x_handle_irq, 1035 .init_machine = spitz_init, 1036 .init_time = pxa_timer_init, 1037 .restart = spitz_restart, 1038 MACHINE_END 1039 #endif 1040 1041 #ifdef CONFIG_MACH_BORZOI 1042 MACHINE_START(BORZOI, "SHARP Borzoi") 1043 .fixup = spitz_fixup, 1044 .map_io = pxa27x_map_io, 1045 .nr_irqs = PXA_NR_IRQS, 1046 .init_irq = pxa27x_init_irq, 1047 .handle_irq = pxa27x_handle_irq, 1048 .init_machine = spitz_init, 1049 .init_time = pxa_timer_init, 1050 .restart = spitz_restart, 1051 MACHINE_END 1052 #endif 1053 1054 #ifdef CONFIG_MACH_AKITA 1055 MACHINE_START(AKITA, "SHARP Akita") 1056 .fixup = spitz_fixup, 1057 .map_io = pxa27x_map_io, 1058 .nr_irqs = PXA_NR_IRQS, 1059 .init_irq = pxa27x_init_irq, 1060 .handle_irq = pxa27x_handle_irq, 1061 .init_machine = spitz_init, 1062 .init_time = pxa_timer_init, 1063 .restart = spitz_restart, 1064 MACHINE_END 1065 #endif 1066