1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * QNAP TS-409 Board Setup 4 * 5 * Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com> 6 * 7 * Copyright (C) 2008 Sylver Bruneau <sylver.bruneau@gmail.com> 8 * Copyright (C) 2008 Martin Michlmayr <tbm@cyrius.com> 9 */ 10 #include <linux/gpio.h> 11 #include <linux/kernel.h> 12 #include <linux/init.h> 13 #include <linux/platform_device.h> 14 #include <linux/pci.h> 15 #include <linux/irq.h> 16 #include <linux/mtd/physmap.h> 17 #include <linux/mv643xx_eth.h> 18 #include <linux/leds.h> 19 #include <linux/gpio_keys.h> 20 #include <linux/input.h> 21 #include <linux/i2c.h> 22 #include <linux/serial_reg.h> 23 #include <asm/mach-types.h> 24 #include <asm/mach/arch.h> 25 #include <asm/mach/pci.h> 26 #include "common.h" 27 #include "mpp.h" 28 #include "orion5x.h" 29 #include "tsx09-common.h" 30 31 /***************************************************************************** 32 * QNAP TS-409 Info 33 ****************************************************************************/ 34 35 /* 36 * QNAP TS-409 hardware : 37 * - Marvell 88F5281-D0 38 * - Marvell 88SX7042 SATA controller (PCIe) 39 * - Marvell 88E1118 Gigabit Ethernet PHY 40 * - RTC S35390A (@0x30) on I2C bus 41 * - 8MB NOR flash 42 * - 256MB of DDR-2 RAM 43 */ 44 45 /* 46 * 8MB NOR flash Device bus boot chip select 47 */ 48 49 #define QNAP_TS409_NOR_BOOT_BASE 0xff800000 50 #define QNAP_TS409_NOR_BOOT_SIZE SZ_8M 51 52 /**************************************************************************** 53 * 8MiB NOR flash. The struct mtd_partition is not in the same order as the 54 * partitions on the device because we want to keep compatibility with 55 * existing QNAP firmware. 56 * 57 * Layout as used by QNAP: 58 * [2] 0x00000000-0x00200000 : "Kernel" 59 * [3] 0x00200000-0x00600000 : "RootFS1" 60 * [4] 0x00600000-0x00700000 : "RootFS2" 61 * [6] 0x00700000-0x00760000 : "NAS Config" (read-only) 62 * [5] 0x00760000-0x00780000 : "U-Boot Config" 63 * [1] 0x00780000-0x00800000 : "U-Boot" (read-only) 64 ***************************************************************************/ 65 static struct mtd_partition qnap_ts409_partitions[] = { 66 { 67 .name = "U-Boot", 68 .size = 0x00080000, 69 .offset = 0x00780000, 70 .mask_flags = MTD_WRITEABLE, 71 }, { 72 .name = "Kernel", 73 .size = 0x00200000, 74 .offset = 0, 75 }, { 76 .name = "RootFS1", 77 .size = 0x00400000, 78 .offset = 0x00200000, 79 }, { 80 .name = "RootFS2", 81 .size = 0x00100000, 82 .offset = 0x00600000, 83 }, { 84 .name = "U-Boot Config", 85 .size = 0x00020000, 86 .offset = 0x00760000, 87 }, { 88 .name = "NAS Config", 89 .size = 0x00060000, 90 .offset = 0x00700000, 91 .mask_flags = MTD_WRITEABLE, 92 }, 93 }; 94 95 static struct physmap_flash_data qnap_ts409_nor_flash_data = { 96 .width = 1, 97 .parts = qnap_ts409_partitions, 98 .nr_parts = ARRAY_SIZE(qnap_ts409_partitions) 99 }; 100 101 static struct resource qnap_ts409_nor_flash_resource = { 102 .flags = IORESOURCE_MEM, 103 .start = QNAP_TS409_NOR_BOOT_BASE, 104 .end = QNAP_TS409_NOR_BOOT_BASE + QNAP_TS409_NOR_BOOT_SIZE - 1, 105 }; 106 107 static struct platform_device qnap_ts409_nor_flash = { 108 .name = "physmap-flash", 109 .id = 0, 110 .dev = { .platform_data = &qnap_ts409_nor_flash_data, }, 111 .num_resources = 1, 112 .resource = &qnap_ts409_nor_flash_resource, 113 }; 114 115 /***************************************************************************** 116 * PCI 117 ****************************************************************************/ 118 119 static int __init qnap_ts409_pci_map_irq(const struct pci_dev *dev, u8 slot, 120 u8 pin) 121 { 122 int irq; 123 124 /* 125 * Check for devices with hard-wired IRQs. 126 */ 127 irq = orion5x_pci_map_irq(dev, slot, pin); 128 if (irq != -1) 129 return irq; 130 131 /* 132 * PCI isn't used on the TS-409 133 */ 134 return -1; 135 } 136 137 static struct hw_pci qnap_ts409_pci __initdata = { 138 .nr_controllers = 2, 139 .setup = orion5x_pci_sys_setup, 140 .scan = orion5x_pci_sys_scan_bus, 141 .map_irq = qnap_ts409_pci_map_irq, 142 }; 143 144 static int __init qnap_ts409_pci_init(void) 145 { 146 if (machine_is_ts409()) 147 pci_common_init(&qnap_ts409_pci); 148 149 return 0; 150 } 151 152 subsys_initcall(qnap_ts409_pci_init); 153 154 /***************************************************************************** 155 * RTC S35390A on I2C bus 156 ****************************************************************************/ 157 158 #define TS409_RTC_GPIO 10 159 160 static struct i2c_board_info __initdata qnap_ts409_i2c_rtc = { 161 I2C_BOARD_INFO("s35390a", 0x30), 162 }; 163 164 /***************************************************************************** 165 * LEDs attached to GPIO 166 ****************************************************************************/ 167 168 static struct gpio_led ts409_led_pins[] = { 169 { 170 .name = "ts409:red:sata1", 171 .gpio = 4, 172 .active_low = 1, 173 }, { 174 .name = "ts409:red:sata2", 175 .gpio = 5, 176 .active_low = 1, 177 }, { 178 .name = "ts409:red:sata3", 179 .gpio = 6, 180 .active_low = 1, 181 }, { 182 .name = "ts409:red:sata4", 183 .gpio = 7, 184 .active_low = 1, 185 }, 186 }; 187 188 static struct gpio_led_platform_data ts409_led_data = { 189 .leds = ts409_led_pins, 190 .num_leds = ARRAY_SIZE(ts409_led_pins), 191 }; 192 193 static struct platform_device ts409_leds = { 194 .name = "leds-gpio", 195 .id = -1, 196 .dev = { 197 .platform_data = &ts409_led_data, 198 }, 199 }; 200 201 /**************************************************************************** 202 * GPIO Attached Keys 203 * Power button is attached to the PIC microcontroller 204 ****************************************************************************/ 205 206 #define QNAP_TS409_GPIO_KEY_RESET 14 207 #define QNAP_TS409_GPIO_KEY_MEDIA 15 208 209 static struct gpio_keys_button qnap_ts409_buttons[] = { 210 { 211 .code = KEY_RESTART, 212 .gpio = QNAP_TS409_GPIO_KEY_RESET, 213 .desc = "Reset Button", 214 .active_low = 1, 215 }, { 216 .code = KEY_COPY, 217 .gpio = QNAP_TS409_GPIO_KEY_MEDIA, 218 .desc = "USB Copy Button", 219 .active_low = 1, 220 }, 221 }; 222 223 static struct gpio_keys_platform_data qnap_ts409_button_data = { 224 .buttons = qnap_ts409_buttons, 225 .nbuttons = ARRAY_SIZE(qnap_ts409_buttons), 226 }; 227 228 static struct platform_device qnap_ts409_button_device = { 229 .name = "gpio-keys", 230 .id = -1, 231 .num_resources = 0, 232 .dev = { 233 .platform_data = &qnap_ts409_button_data, 234 }, 235 }; 236 237 /***************************************************************************** 238 * General Setup 239 ****************************************************************************/ 240 static unsigned int ts409_mpp_modes[] __initdata = { 241 MPP0_UNUSED, 242 MPP1_UNUSED, 243 MPP2_UNUSED, 244 MPP3_UNUSED, 245 MPP4_GPIO, /* HDD 1 status */ 246 MPP5_GPIO, /* HDD 2 status */ 247 MPP6_GPIO, /* HDD 3 status */ 248 MPP7_GPIO, /* HDD 4 status */ 249 MPP8_UNUSED, 250 MPP9_UNUSED, 251 MPP10_GPIO, /* RTC int */ 252 MPP11_UNUSED, 253 MPP12_UNUSED, 254 MPP13_UNUSED, 255 MPP14_GPIO, /* SW_RST */ 256 MPP15_GPIO, /* USB copy button */ 257 MPP16_UART, /* UART1 RXD */ 258 MPP17_UART, /* UART1 TXD */ 259 MPP18_UNUSED, 260 MPP19_UNUSED, 261 0, 262 }; 263 264 static void __init qnap_ts409_init(void) 265 { 266 /* 267 * Setup basic Orion functions. Need to be called early. 268 */ 269 orion5x_init(); 270 271 orion5x_mpp_conf(ts409_mpp_modes); 272 273 /* 274 * Configure peripherals. 275 */ 276 mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET, 277 ORION_MBUS_DEVBUS_BOOT_ATTR, 278 QNAP_TS409_NOR_BOOT_BASE, 279 QNAP_TS409_NOR_BOOT_SIZE); 280 platform_device_register(&qnap_ts409_nor_flash); 281 282 orion5x_ehci0_init(); 283 qnap_tsx09_find_mac_addr(QNAP_TS409_NOR_BOOT_BASE + 284 qnap_ts409_partitions[5].offset, 285 qnap_ts409_partitions[5].size); 286 orion5x_eth_init(&qnap_tsx09_eth_data); 287 orion5x_i2c_init(); 288 orion5x_uart0_init(); 289 orion5x_uart1_init(); 290 291 platform_device_register(&qnap_ts409_button_device); 292 293 /* Get RTC IRQ and register the chip */ 294 if (gpio_request(TS409_RTC_GPIO, "rtc") == 0) { 295 if (gpio_direction_input(TS409_RTC_GPIO) == 0) 296 qnap_ts409_i2c_rtc.irq = gpio_to_irq(TS409_RTC_GPIO); 297 else 298 gpio_free(TS409_RTC_GPIO); 299 } 300 if (qnap_ts409_i2c_rtc.irq == 0) 301 pr_warn("qnap_ts409_init: failed to get RTC IRQ\n"); 302 i2c_register_board_info(0, &qnap_ts409_i2c_rtc, 1); 303 platform_device_register(&ts409_leds); 304 305 /* register tsx09 specific power-off method */ 306 pm_power_off = qnap_tsx09_power_off; 307 } 308 309 MACHINE_START(TS409, "QNAP TS-409") 310 /* Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com> */ 311 .atag_offset = 0x100, 312 .nr_irqs = ORION5X_NR_IRQS, 313 .init_machine = qnap_ts409_init, 314 .map_io = orion5x_map_io, 315 .init_early = orion5x_init_early, 316 .init_irq = orion5x_init_irq, 317 .init_time = orion5x_timer_init, 318 .fixup = tag_fixup_mem32, 319 .restart = orion5x_restart, 320 MACHINE_END 321