1if ARCH_DAVINCI 2 3config AINTC 4 bool 5 6config CP_INTC 7 bool 8 select IRQ_DOMAIN 9 10config ARCH_DAVINCI_DMx 11 bool 12 select CPU_ARM926T 13 14menu "TI DaVinci Implementations" 15 16comment "DaVinci Core Type" 17 18config ARCH_DAVINCI_DM644x 19 bool "DaVinci 644x based system" 20 select AINTC 21 select ARCH_DAVINCI_DMx 22 23config ARCH_DAVINCI_DM355 24 bool "DaVinci 355 based system" 25 select AINTC 26 select ARCH_DAVINCI_DMx 27 28config ARCH_DAVINCI_DM646x 29 bool "DaVinci 646x based system" 30 select AINTC 31 select ARCH_DAVINCI_DMx 32 33config ARCH_DAVINCI_DA830 34 bool "DA830/OMAP-L137/AM17x based system" 35 depends on !ARCH_DAVINCI_DMx || AUTO_ZRELADDR 36 select ARCH_DAVINCI_DA8XX 37 select CPU_DCACHE_WRITETHROUGH # needed on silicon revs 1.0, 1.1 38 select CP_INTC 39 40config ARCH_DAVINCI_DA850 41 bool "DA850/OMAP-L138/AM18x based system" 42 depends on !ARCH_DAVINCI_DMx || AUTO_ZRELADDR 43 select ARCH_DAVINCI_DA8XX 44 select CP_INTC 45 46config ARCH_DAVINCI_DA8XX 47 bool 48 select CPU_ARM926T 49 50config ARCH_DAVINCI_DM365 51 bool "DaVinci 365 based system" 52 select AINTC 53 select ARCH_DAVINCI_DMx 54 55comment "DaVinci Board Type" 56 57config MACH_DA8XX_DT 58 bool "Support DA8XX platforms using device tree" 59 default y 60 depends on ARCH_DAVINCI_DA8XX 61 select PINCTRL 62 help 63 Say y here to include support for TI DaVinci DA850 based using 64 Flattened Device Tree. More information at Documentation/devicetree 65 66config MACH_DAVINCI_EVM 67 bool "TI DM644x EVM" 68 default ARCH_DAVINCI_DM644x 69 depends on ARCH_DAVINCI_DM644x 70 select EEPROM_AT24 71 select I2C 72 help 73 Configure this option to specify the whether the board used 74 for development is a DM644x EVM 75 76config MACH_SFFSDR 77 bool "Lyrtech SFFSDR" 78 depends on ARCH_DAVINCI_DM644x 79 select EEPROM_AT24 80 select I2C 81 help 82 Say Y here to select the Lyrtech Small Form Factor 83 Software Defined Radio (SFFSDR) board. 84 85config MACH_NEUROS_OSD2 86 bool "Neuros OSD2 Open Television Set Top Box" 87 depends on ARCH_DAVINCI_DM644x 88 help 89 Configure this option to specify the whether the board used 90 for development is a Neuros OSD2 Open Set Top Box. 91 92config MACH_DAVINCI_DM355_EVM 93 bool "TI DM355 EVM" 94 default ARCH_DAVINCI_DM355 95 depends on ARCH_DAVINCI_DM355 96 help 97 Configure this option to specify the whether the board used 98 for development is a DM355 EVM 99 100config MACH_DM355_LEOPARD 101 bool "DM355 Leopard board" 102 depends on ARCH_DAVINCI_DM355 103 help 104 Configure this option to specify the whether the board used 105 for development is a DM355 Leopard board. 106 107config MACH_DAVINCI_DM6467_EVM 108 bool "TI DM6467 EVM" 109 default ARCH_DAVINCI_DM646x 110 depends on ARCH_DAVINCI_DM646x 111 select EEPROM_AT24 112 select I2C 113 select MACH_DAVINCI_DM6467TEVM 114 help 115 Configure this option to specify the whether the board used 116 for development is a DM6467 EVM 117 118config MACH_DAVINCI_DM6467TEVM 119 bool 120 121config MACH_DAVINCI_DM365_EVM 122 bool "TI DM365 EVM" 123 default ARCH_DAVINCI_DM365 124 depends on ARCH_DAVINCI_DM365 125 select EEPROM_AT24 126 select I2C 127 help 128 Configure this option to specify whether the board used 129 for development is a DM365 EVM 130 131config MACH_DAVINCI_DA830_EVM 132 bool "TI DA830/OMAP-L137/AM17x Reference Platform" 133 default ARCH_DAVINCI_DA830 134 depends on ARCH_DAVINCI_DA830 135 select EEPROM_AT24 136 select GPIO_PCF857X 137 select I2C 138 help 139 Say Y here to select the TI DA830/OMAP-L137/AM17x Evaluation Module. 140 141choice 142 prompt "Select DA830/OMAP-L137/AM17x UI board peripheral" 143 depends on MACH_DAVINCI_DA830_EVM 144 help 145 The presence of UI card on the DA830/OMAP-L137/AM17x EVM is 146 detected automatically based on successful probe of the I2C 147 based GPIO expander on that board. This option selected in this 148 menu has an effect only in case of a successful UI card detection. 149 150config DA830_UI_LCD 151 bool "LCD" 152 help 153 Say Y here to use the LCD as a framebuffer or simple character 154 display. 155 156config DA830_UI_NAND 157 bool "NAND flash" 158 help 159 Say Y here to use the NAND flash. Do not forget to setup 160 the switch correctly. 161endchoice 162 163config MACH_DAVINCI_DA850_EVM 164 bool "TI DA850/OMAP-L138/AM18x Reference Platform" 165 default ARCH_DAVINCI_DA850 166 depends on ARCH_DAVINCI_DA850 167 help 168 Say Y here to select the TI DA850/OMAP-L138/AM18x Evaluation Module. 169 170choice 171 prompt "Select peripherals connected to expander on UI board" 172 depends on MACH_DAVINCI_DA850_EVM 173 help 174 The presence of User Interface (UI) card on the DA850/OMAP-L138/AM18x 175 EVM is detected automatically based on successful probe of the I2C 176 based GPIO expander on that card. This option selected in this 177 menu has an effect only in case of a successful UI card detection. 178 179config DA850_UI_NONE 180 bool "No peripheral is enabled" 181 help 182 Say Y if you do not want to enable any of the peripherals connected 183 to TCA6416 expander on DA850/OMAP-L138/AM18x EVM UI card 184 185config DA850_UI_RMII 186 bool "RMII Ethernet PHY" 187 help 188 Say Y if you want to use the RMII PHY on the DA850/OMAP-L138/AM18x 189 EVM. This PHY is found on the UI daughter card that is supplied with 190 the EVM. 191 NOTE: Please take care while choosing this option, MII PHY will 192 not be functional if RMII mode is selected. 193 194config DA850_UI_SD_VIDEO_PORT 195 bool "Video Port Interface" 196 help 197 Say Y if you want to use Video Port Interface (VPIF) on the 198 DA850/OMAP-L138 EVM. The Video decoders/encoders are found on the 199 UI daughter card that is supplied with the EVM. 200 201endchoice 202 203config DA850_WL12XX 204 bool "AM18x wl1271 daughter board" 205 depends on MACH_DAVINCI_DA850_EVM 206 help 207 The wl1271 daughter card for AM18x EVMs is a combo wireless 208 connectivity add-on card, based on the LS Research TiWi module with 209 Texas Instruments' wl1271 solution. 210 Say Y if you want to use a wl1271 expansion card connected to the 211 AM18x EVM. 212 213 214config MACH_MITYOMAPL138 215 bool "Critical Link MityDSP-L138/MityARM-1808 SoM" 216 depends on ARCH_DAVINCI_DA850 217 select EEPROM_AT24 218 select I2C 219 help 220 Say Y here to select the Critical Link MityDSP-L138/MityARM-1808 221 System on Module. Information on this SoM may be found at 222 http://www.mitydsp.com 223 224config MACH_OMAPL138_HAWKBOARD 225 bool "TI AM1808 / OMAPL-138 Hawkboard platform" 226 depends on ARCH_DAVINCI_DA850 227 help 228 Say Y here to select the TI AM1808 / OMAPL-138 Hawkboard platform . 229 Information of this board may be found at 230 http://www.hawkboard.org/ 231 232config DAVINCI_MUX 233 bool "DAVINCI multiplexing support" 234 depends on ARCH_DAVINCI 235 default y 236 help 237 Pin multiplexing support for DAVINCI boards. If your bootloader 238 sets the multiplexing correctly, say N. Otherwise, or if unsure, 239 say Y. 240 241config DAVINCI_MUX_DEBUG 242 bool "Multiplexing debug output" 243 depends on DAVINCI_MUX 244 help 245 Makes the multiplexing functions print out a lot of debug info. 246 This is useful if you want to find out the correct values of the 247 multiplexing registers. 248 249config DAVINCI_MUX_WARNINGS 250 bool "Warn about pins the bootloader didn't set up" 251 depends on DAVINCI_MUX 252 help 253 Choose Y here to warn whenever driver initialization logic needs 254 to change the pin multiplexing setup. When there are no warnings 255 printed, it's safe to deselect DAVINCI_MUX for your product. 256 257config DAVINCI_RESET_CLOCKS 258 bool "Reset unused clocks during boot" 259 depends on ARCH_DAVINCI 260 help 261 Say Y if you want to reset unused clocks during boot. 262 This option saves power, but assumes all drivers are 263 using the clock framework. Broken drivers that do not 264 yet use clock framework may not work with this option. 265 If you are booting from another operating system, you 266 probably do not want this option enabled until your 267 device drivers work properly. 268 269endmenu 270 271endif 272