xref: /linux/arch/arm/boot/dts/ti/omap/am335x-sl50.dts (revision bfb921b2a9d5d1123d1d10b196a39db629ddef87)
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Copyright (C) 2015 Toby Churchill - https://www.toby-churchill.com/
4 * url above is defunct
5 */
6/dts-v1/;
7
8#include "am33xx.dtsi"
9#include <dt-bindings/pwm/pwm.h>
10#include <dt-bindings/interrupt-controller/irq.h>
11
12/ {
13	model = "Toby Churchill SL50 Series";
14	compatible = "tcl,am335x-sl50", "ti,am33xx";
15
16	cpus {
17		cpu@0 {
18			cpu0-supply = <&dcdc2_reg>;
19		};
20	};
21
22	memory@80000000 {
23		device_type = "memory";
24		reg = <0x80000000 0x20000000>; /* 512 MB */
25	};
26
27	chosen {
28		stdout-path = &uart0;
29	};
30
31	leds {
32		compatible = "gpio-leds";
33		pinctrl-names = "default";
34		pinctrl-0 = <&led_pins>;
35
36		led0 {
37			label = "sl50:red:usr0";
38			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
39			default-state = "off";
40		};
41
42		led1 {
43			label = "sl50:green:usr1";
44			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
45			default-state = "off";
46		};
47
48		led2 {
49			label = "sl50:red:usr2";
50			gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
51			default-state = "off";
52		};
53
54		led3 {
55			label = "sl50:green:usr3";
56			gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
57			default-state = "off";
58		};
59	};
60
61	backlight0: disp0 {
62		compatible = "pwm-backlight";
63		pinctrl-names = "default";
64		pinctrl-0 = <&backlight0_pins>;
65		pwms = <&ehrpwm1 0 500000 PWM_POLARITY_INVERTED>;
66		brightness-levels = < 0  1  2  3  4  5  6  7  8  9
67				     10 11 12 13 14 15 16 17 18 19
68				     20 21 22 23 24 25 26 27 28 29
69				     30 31 32 33 34 35 36 37 38 39
70				     40 41 42 43 44 45 46 47 48 49
71				     50 51 52 53 54 55 56 57 58 59
72				     60 61 62 63 64 65 66 67 68 69
73				     70 71 72 73 74 75 76 77 78 79
74				     80 81 82 83 84 85 86 87 88 89
75				     90 91 92 93 94 95 96 97 98 99
76				    100>;
77		default-brightness-level = <50>;
78		enable-gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
79		power-supply = <&vdd_sys_reg>;
80	};
81
82	backlight1: disp1 {
83		compatible = "pwm-backlight";
84		pinctrl-names = "default";
85		pinctrl-0 = <&backlight1_pins>;
86		pwms = <&ehrpwm1 1 500000 PWM_POLARITY_INVERTED>;
87		brightness-levels = < 0  1  2  3  4  5  6  7  8  9
88				     10 11 12 13 14 15 16 17 18 19
89				     20 21 22 23 24 25 26 27 28 29
90				     30 31 32 33 34 35 36 37 38 39
91				     40 41 42 43 44 45 46 47 48 49
92				     50 51 52 53 54 55 56 57 58 59
93				     60 61 62 63 64 65 66 67 68 69
94				     70 71 72 73 74 75 76 77 78 79
95				     80 81 82 83 84 85 86 87 88 89
96				     90 91 92 93 94 95 96 97 98 99
97				    100>;
98		default-brightness-level = <50>;
99		enable-gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
100		power-supply = <&vdd_sys_reg>;
101	};
102
103	clocks {
104		compatible = "simple-bus";
105		#address-cells = <1>;
106		#size-cells = <0>;
107
108		/* audio external oscillator */
109		audio_mclk_fixed: oscillator@0 {
110			compatible = "fixed-clock";
111			#clock-cells = <0>;
112			clock-frequency  = <24576000>;	/* 24.576MHz */
113		};
114
115		audio_mclk: audio_mclk_gate@0 {
116			compatible = "gpio-gate-clock";
117			#clock-cells = <0>;
118			pinctrl-names = "default";
119			pinctrl-0 = <&audio_mclk_pins>;
120			clocks = <&audio_mclk_fixed>;
121			enable-gpios = <&gpio1 27 0>;
122		};
123	};
124
125	panel: lcd_panel {
126		compatible = "ti,tilcdc,panel";
127		pinctrl-names = "default";
128		pinctrl-0 = <&lcd_pins>;
129
130		panel-info {
131			ac-bias = <255>;
132			ac-bias-intrpt = <0>;
133			dma-burst-sz = <16>;
134			bpp = <16>;
135			fdd = <0x80>;
136			tft-alt-mode = <0>;
137			mono-8bit-mode = <0>;
138			sync-edge = <0>;
139			sync-ctrl = <1>;
140			raster-order = <0>;
141			fifo-th = <0>;
142		};
143
144		display-timings {
145			native-mode = <&timing0>;
146			timing0: 960x128 {
147				clock-frequency = <18000000>;
148				hactive = <960>;
149				vactive = <272>;
150
151				hback-porch = <40>;
152				hfront-porch = <16>;
153				hsync-len = <24>;
154				hsync-active = <0>;
155
156				vback-porch = <3>;
157				vfront-porch = <8>;
158				vsync-len = <4>;
159				vsync-active = <0>;
160			};
161		};
162	};
163
164	sound {
165		compatible = "audio-graph-card";
166		label = "sound-card";
167		pinctrl-names = "default";
168		pinctrl-0 = <&audio_pa_pins>;
169
170		widgets = "Headphone", "Headphone Jack",
171			  "Speaker", "Speaker External",
172			  "Line", "Line In",
173			  "Microphone", "Microphone Jack";
174
175		routing = "Headphone Jack",	"HPLOUT",
176			  "Headphone Jack",	"HPROUT",
177			  "Amplifier",		"MONO_LOUT",
178			  "Speaker External",	"Amplifier",
179			  "LINE1R",		"Line In",
180			  "LINE1L",		"Line In",
181			  "MIC3L",		"Microphone Jack",
182			  "MIC3R",		"Microphone Jack",
183			  "Microphone Jack",	"Mic Bias";
184
185		dais = <&cpu_port>;
186
187		pa-gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>;
188	};
189
190	emmc_pwrseq: pwrseq@0 {
191		compatible = "mmc-pwrseq-emmc";
192		pinctrl-names = "default";
193		pinctrl-0 = <&emmc_pwrseq_pins>;
194		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
195	};
196
197	vdd_sys_reg: regulator@0 {
198		compatible = "regulator-fixed";
199		regulator-name = "vdd_sys_reg";
200		regulator-min-microvolt = <5000000>;
201		regulator-max-microvolt = <5000000>;
202		regulator-always-on;
203	};
204
205	vmmcsd_fixed: fixedregulator0 {
206		compatible = "regulator-fixed";
207		regulator-name = "vmmcsd_fixed";
208		regulator-min-microvolt = <3300000>;
209		regulator-max-microvolt = <3300000>;
210	};
211};
212
213&am33xx_pinmux {
214	pinctrl-names = "default";
215	pinctrl-0 = <&lwb_pins>;
216
217	audio_pins: audio-pins {
218		pinctrl-single,pins = <
219			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLDOWN, MUX_MODE0)
220			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_INPUT_PULLDOWN, MUX_MODE0)
221			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_INPUT_PULLDOWN, MUX_MODE0)
222			AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR0, PIN_INPUT_PULLDOWN, MUX_MODE0)
223			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE2)
224		>;
225	};
226
227	audio_pa_pins: audio-pa-pins {
228		pinctrl-single,pins = <
229			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKR, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* SoundPA_en - mcasp0_aclkr.gpio3_18 */
230		>;
231	};
232
233	audio_mclk_pins: audio-mclk-pins {
234		pinctrl-single,pins = <
235			AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* gpmc_a11.gpio1_27 */
236		>;
237	};
238
239	backlight0_pins: backlight0-pins {
240		pinctrl-single,pins = <
241			AM33XX_PADCONF(AM335X_PIN_GPMC_WEN, PIN_OUTPUT, MUX_MODE7)	/* gpmc_wen.gpio2_4 */
242		>;
243	};
244
245	backlight1_pins: backlight1-pins {
246		pinctrl-single,pins = <
247			AM33XX_PADCONF(AM335X_PIN_GPMC_AD10, PIN_OUTPUT, MUX_MODE7)     /* gpmc_ad10.gpio0_26 */
248		>;
249	};
250
251	lcd_pins: lcd-pins {
252		pinctrl-single,pins = <
253			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0)
254			AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0)
255			AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0)
256			AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PIN_OUTPUT, MUX_MODE0)
257			AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PIN_OUTPUT, MUX_MODE0)
258			AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PIN_OUTPUT, MUX_MODE0)
259			AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PIN_OUTPUT, MUX_MODE0)
260			AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PIN_OUTPUT, MUX_MODE0)
261			AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PIN_OUTPUT, MUX_MODE0)
262			AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_OUTPUT, MUX_MODE0)
263			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_OUTPUT, MUX_MODE0)
264			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE0)
265			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_OUTPUT, MUX_MODE0)
266			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE0)
267			AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PIN_OUTPUT, MUX_MODE0)
268			AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PIN_OUTPUT, MUX_MODE0)
269			AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
270			AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
271			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
272			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
273		>;
274	};
275
276	led_pins: led-pins {
277		pinctrl-single,pins = <
278			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT, MUX_MODE7)	/* gpmc_a5.gpio1_21 */
279			AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_OUTPUT, MUX_MODE7)	/* gpmc_a6.gpio1_22 */
280			AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_OUTPUT, MUX_MODE7)	/* gpmc_a7.gpio1_23 */
281			AM33XX_PADCONF(AM335X_PIN_GPMC_A8, PIN_OUTPUT, MUX_MODE7)	/* gpmc_a8.gpio1_24 */
282		>;
283	};
284
285	uart0_pins: uart0-pins {
286		pinctrl-single,pins = <
287			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
288			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
289		>;
290	};
291
292	uart1_pins: uart1-pins {
293		pinctrl-single,pins = <
294			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
295			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
296		>;
297	};
298
299	uart4_pins: uart4-pins {
300		pinctrl-single,pins = <
301			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE6)	/* gpmc_wait0.uart4_rxd */
302			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_OUTPUT_PULLDOWN, MUX_MODE6)	/* gpmc_wpn.uart4_txd */
303		>;
304	};
305
306	i2c0_pins: i2c0-pins {
307		pinctrl-single,pins = <
308			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0)
309			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0)
310		>;
311	};
312
313	i2c2_pins: i2c2-pins {
314		pinctrl-single,pins = <
315			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* uart1_ctsn.i2c2_sda */
316			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* uart1_rtsn.i2c2_scl */
317		>;
318	};
319
320	cpsw_default: cpsw-default-pins {
321		pinctrl-single,pins = <
322			/* Slave 1 */
323			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLUP, MUX_MODE0)
324			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
325			AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLUP, MUX_MODE0)
326			AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
327			AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
328			AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
329			AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
330			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLUP, MUX_MODE0)
331			AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLUP, MUX_MODE0)
332			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLUP, MUX_MODE0)
333			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLUP, MUX_MODE0)
334			AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLUP, MUX_MODE0)
335			AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLUP, MUX_MODE0)
336		>;
337	};
338
339	cpsw_sleep: cpsw-sleep-pins {
340		pinctrl-single,pins = <
341			/* Slave 1 reset value */
342			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE7)
343			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)
344			AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE7)
345			AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_INPUT_PULLDOWN, MUX_MODE7)
346			AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_INPUT_PULLDOWN, MUX_MODE7)
347			AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_INPUT_PULLDOWN, MUX_MODE7)
348			AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_INPUT_PULLDOWN, MUX_MODE7)
349			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
350			AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
351			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE7)
352			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE7)
353			AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE7)
354			AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE7)
355		>;
356	};
357
358	davinci_mdio_default: davinci-mdio-default-pins {
359		pinctrl-single,pins = <
360			/* MDIO */
361			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
362			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0)
363			/* Ethernet */
364			AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_INPUT_PULLUP, MUX_MODE7)	/* Ethernet_nRST - gpmc_ad14.gpio1_14 */
365		>;
366	};
367
368	davinci_mdio_sleep: davinci-mdio-sleep-pins {
369		pinctrl-single,pins = <
370			/* MDIO reset value */
371			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
372			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_INPUT_PULLDOWN, MUX_MODE7)
373		>;
374	};
375
376	mmc1_pins: mmc1-pins {
377		pinctrl-single,pins = <
378			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT, MUX_MODE7)		/* uart0_rtsn.gpio1_9 */
379		>;
380	};
381
382	emmc_pwrseq_pins: emmc-pwrseq-pins {
383		pinctrl-single,pins = <
384			AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_OUTPUT_PULLUP, MUX_MODE7)	/* gpmc_a4.gpio1_20 */
385		>;
386	};
387
388	emmc_pins: emmc-pins {
389		pinctrl-single,pins = <
390			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_INPUT_PULLUP, MUX_MODE2)	/* gpmc_csn1.mmc1_clk */
391			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN2, PIN_INPUT_PULLUP, MUX_MODE2)	/* gpmc_csn2.mmc1_cmd */
392			AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE1)	/* gpmc_ad0.mmc1_dat0 */
393			AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE1)	/* gpmc_ad1.mmc1_dat1 */
394			AM33XX_PADCONF(AM335X_PIN_GPMC_AD2, PIN_INPUT_PULLUP, MUX_MODE1)	/* gpmc_ad2.mmc1_dat2 */
395			AM33XX_PADCONF(AM335X_PIN_GPMC_AD3, PIN_INPUT_PULLUP, MUX_MODE1)	/* gpmc_ad3.mmc1_dat3 */
396			AM33XX_PADCONF(AM335X_PIN_GPMC_AD4, PIN_INPUT_PULLUP, MUX_MODE1)	/* gpmc_ad4.mmc1_dat4 */
397			AM33XX_PADCONF(AM335X_PIN_GPMC_AD5, PIN_INPUT_PULLUP, MUX_MODE1) 	/* gpmc_ad5.mmc1_dat5 */
398			AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLUP, MUX_MODE1)	/* gpmc_ad6.mmc1_dat6 */
399			AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLUP, MUX_MODE1)	/* gpmc_ad7.mmc1_dat7 */
400		>;
401	};
402
403	ehrpwm1_pins: ehrpwm1a-pins {
404		pinctrl-single,pins = <
405			AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_OUTPUT, MUX_MODE6)	/* gpmc_a2.ehrpwm1a */
406			AM33XX_PADCONF(AM335X_PIN_GPMC_A3, PIN_OUTPUT, MUX_MODE6)	/* gpmc_a3.ehrpwm1b */
407		>;
408	};
409
410	rtc0_irq_pins: rtc0-irq-pins {
411		pinctrl-single,pins = <
412			AM33XX_PADCONF(AM335X_PIN_GPMC_AD9, PIN_INPUT_PULLUP, MUX_MODE7)     /* gpmc_ad9.gpio0_23 */
413		>;
414	};
415
416	spi0_pins: spi0-pins {
417		pinctrl-single,pins = <
418			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_INPUT_PULLUP, MUX_MODE0)	/* SPI0_MOSI */
419			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT_PULLUP, MUX_MODE0)	/* SPI0_MISO */
420			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLUP, MUX_MODE0)
421			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLUP, MUX_MODE0)	/* SPI0_CS0 (NBATTSS) */
422			AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT_PULLUP, MUX_MODE0)	/* SPI0_CS1 (FPGA_FLASH_NCS) */
423		>;
424	};
425
426	lwb_pins: lwb-pins {
427		pinctrl-single,pins = <
428			AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLUP, MUX_MODE7)	/* nKbdInt - gpmc_ad12.gpio1_12 */
429			AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT_PULLUP, MUX_MODE7)	/* nKbdReset - gpmc_ad13.gpio1_13 */
430			AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLUP, MUX_MODE7)	/* USB1_enPower - gpmc_a1.gpio1_17 */
431			/* PDI Bus - Battery system */
432			AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_INPUT_PULLUP, MUX_MODE7)	/* nBattReset  gpmc_a0.gpio1_16 */
433			AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT_PULLUP, MUX_MODE7)	/* BattPDIData gpmc_ad15.gpio1_15 */
434			/* FPGA */
435			AM33XX_PADCONF(AM335X_PIN_GPMC_AD8, PIN_INPUT_PULLUP, MUX_MODE7)	/* FPGA_DONE - gpmc_ad8.gpio0_22 */
436			AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_INPUT_PULLUP, MUX_MODE7)	/* FPGA_NRST - gpmc_a0.gpio1_16 */
437			AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* FPGA_RUN - gpmc_a1.gpio1_17 */
438			AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT_PULLUP, MUX_MODE7)	/* ENFPGA - gpmc_a9.gpio1_25 */
439			AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* FPGA_PROGRAM - gpmc_a10.gpio1_26 */
440		>;
441	};
442};
443
444&i2c0 {
445	status = "okay";
446	pinctrl-names = "default";
447	pinctrl-0 = <&i2c0_pins>;
448
449	clock-frequency = <400000>;
450
451	tps: tps@24 {
452		reg = <0x24>;
453	};
454
455	rtc0: rtc@68 {
456		compatible = "dallas,ds1339";
457		pinctrl-names = "default";
458		pinctrl-0 = <&rtc0_irq_pins>;
459		interrupt-parent = <&gpio0>;
460		interrupts = <23 IRQ_TYPE_EDGE_FALLING>; /* gpio 23 */
461		wakeup-source;
462		trickle-resistor-ohms = <2000>;
463		reg = <0x68>;
464	};
465
466	eeprom: eeprom@50 {
467		compatible = "atmel,24c256";
468		reg = <0x50>;
469	};
470
471	gpio_exp: mcp23017@20 {
472		compatible = "microchip,mcp23017";
473		reg = <0x20>;
474	};
475
476};
477
478&i2c2 {
479	status = "okay";
480	pinctrl-names = "default";
481	pinctrl-0 = <&i2c2_pins>;
482
483	clock-frequency = <400000>;
484
485	audio_codec: tlv320aic3106@1b {
486		status = "okay";
487		compatible = "ti,tlv320aic3106";
488		#sound-dai-cells = <0>;
489		reg = <0x1b>;
490		ai3x-micbias-vg = <2>;  /* 2.5V */
491
492		AVDD-supply = <&ldo4_reg>;
493		IOVDD-supply = <&ldo4_reg>;
494		DRVDD-supply = <&ldo4_reg>;
495		DVDD-supply = <&ldo3_reg>;
496
497		codec_port: port {
498			codec_endpoint: endpoint {
499				remote-endpoint = <&cpu_endpoint>;
500				clocks = <&audio_mclk>;
501			};
502		};
503	};
504
505	/* Ambient Light Sensor */
506	als: isl29023@44 {
507		compatible = "isil,isl29023";
508		reg = <0x44>;
509	};
510};
511
512&rtc {
513	status = "disabled";
514};
515
516&usb0 {
517	dr_mode = "otg";
518};
519
520&usb1 {
521	dr_mode = "host";
522};
523
524&mmc1 {
525	status = "okay";
526	pinctrl-names = "default";
527	pinctrl-0 = <&mmc1_pins>;
528	bus-width = <4>;
529	cd-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
530	vmmc-supply = <&vmmcsd_fixed>;
531};
532
533&mmc2 {
534	status = "okay";
535	pinctrl-names = "default";
536	pinctrl-0 = <&emmc_pins>;
537	bus-width = <8>;
538	vmmc-supply = <&vmmcsd_fixed>;
539	mmc-pwrseq = <&emmc_pwrseq>;
540};
541
542&mcasp0 {
543	status = "okay";
544	pinctrl-names = "default";
545	pinctrl-0 = <&audio_pins>;
546	#sound-dai-cells = <0>;
547	op-mode = <0>;  /* MCASP_ISS_MODE */
548	tdm-slots = <2>;
549	/* 4 serializers */
550	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
551		0 0 1 2
552	>;
553	tx-num-evt = <32>;
554	rx-num-evt = <32>;
555
556	cpu_port: port {
557		cpu_endpoint: endpoint {
558			remote-endpoint = <&codec_endpoint>;
559
560			dai-format = "dsp_b";
561			bitclock-master = <&codec_port>;
562			frame-master = <&codec_port>;
563			bitclock-inversion;
564			clocks = <&audio_mclk>;
565		};
566	};
567};
568
569&uart0 {
570	status = "okay";
571	pinctrl-names = "default";
572	pinctrl-0 = <&uart0_pins>;
573};
574
575&uart1 {
576	status = "okay";
577	pinctrl-names = "default";
578	pinctrl-0 = <&uart1_pins>;
579};
580
581&uart4 {
582	status = "okay";
583	pinctrl-names = "default";
584	pinctrl-0 = <&uart4_pins>;
585};
586
587&spi0 {
588	status = "okay";
589	pinctrl-names = "default";
590	pinctrl-0 = <&spi0_pins>;
591
592	flash: flash@1 {
593		#address-cells = <1>;
594		#size-cells = <1>;
595		compatible = "micron,n25q032";
596		reg = <1>;
597		spi-max-frequency = <5000000>;
598	};
599};
600
601#include "../../tps65217.dtsi"
602
603&tps {
604	ti,pmic-shutdown-controller;
605
606	interrupt-parent = <&intc>;
607	interrupts = <7>;	/* NNMI */
608
609	regulators {
610		dcdc1_reg: regulator@0 {
611			/* VDDS_DDR */
612			regulator-min-microvolt = <1500000>;
613			regulator-max-microvolt = <1500000>;
614			regulator-always-on;
615		};
616
617		dcdc2_reg: regulator@1 {
618			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
619			regulator-name = "vdd_mpu";
620			regulator-min-microvolt = <925000>;
621			regulator-max-microvolt = <1325000>;
622			regulator-boot-on;
623			regulator-always-on;
624		};
625
626		dcdc3_reg: regulator@2 {
627			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
628			regulator-name = "vdd_core";
629			regulator-min-microvolt = <925000>;
630			regulator-max-microvolt = <1150000>;
631			regulator-boot-on;
632			regulator-always-on;
633		};
634
635		ldo1_reg: regulator@3 {
636			/* VRTC / VIO / VDDS*/
637			regulator-always-on;
638			regulator-min-microvolt = <1800000>;
639			regulator-max-microvolt = <1800000>;
640		};
641
642		ldo2_reg: regulator@4 {
643			/* VDD_3V3AUX */
644			regulator-always-on;
645			regulator-min-microvolt = <3300000>;
646			regulator-max-microvolt = <3300000>;
647		};
648
649		ldo3_reg: regulator@5 {
650			/* VDD_1V8 */
651			regulator-min-microvolt = <1800000>;
652			regulator-max-microvolt = <1800000>;
653			regulator-always-on;
654		};
655
656		ldo4_reg: regulator@6 {
657			/* VDD_3V3A */
658			regulator-min-microvolt = <3300000>;
659			regulator-max-microvolt = <3300000>;
660			regulator-always-on;
661		};
662	};
663};
664
665&cpsw_port1 {
666	phy-mode = "mii";
667	phy-handle = <&ethphy0>;
668	ti,dual-emac-pvid = <1>;
669};
670
671&cpsw_port2 {
672	status = "disabled";
673};
674
675&mac_sw {
676	status = "okay";
677	pinctrl-names = "default", "sleep";
678	pinctrl-0 = <&cpsw_default>;
679	pinctrl-1 = <&cpsw_sleep>;
680};
681
682&davinci_mdio_sw {
683	pinctrl-names = "default", "sleep";
684	pinctrl-0 = <&davinci_mdio_default>;
685	pinctrl-1 = <&davinci_mdio_sleep>;
686	reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
687	reset-delay-us = <100>;   /* PHY datasheet states 100us min */
688
689	ethphy0: ethernet-phy@0 {
690		reg = <0>;
691	};
692};
693
694&sham {
695	status = "okay";
696};
697
698&aes {
699	status = "okay";
700};
701
702&epwmss1 {
703	status = "okay";
704};
705
706&ehrpwm1 {
707	status = "okay";
708	pinctrl-names = "default";
709	pinctrl-0 = <&ehrpwm1_pins>;
710};
711
712&lcdc {
713	status = "okay";
714};
715
716&tscadc {
717	status = "okay";
718};
719
720&am335x_adc {
721	ti,adc-channels = <0 1 2 3 4 5 6 7>;
722};
723