1// SPDX-License-Identifier: GPL-2.0 2/* 3 * Device Tree Source for the Lager board 4 * 5 * Copyright (C) 2013-2014 Renesas Solutions Corp. 6 * Copyright (C) 2014 Cogent Embedded, Inc. 7 * Copyright (C) 2015-2016 Renesas Electronics Corporation 8 */ 9 10/* 11 * SSI-AK4643 12 * 13 * SW1: 1: AK4643 14 * 2: CN22 15 * 3: ADV7511 16 * 17 * This command is required when Playback/Capture 18 * 19 * amixer set "LINEOUT Mixer DACL" on 20 * amixer set "DVC Out" 100% 21 * amixer set "DVC In" 100% 22 * 23 * You can use Mute 24 * 25 * amixer set "DVC Out Mute" on 26 * amixer set "DVC In Mute" on 27 * 28 * You can use Volume Ramp 29 * 30 * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps" 31 * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps" 32 * amixer set "DVC Out Ramp" on 33 * aplay xxx.wav & 34 * amixer set "DVC Out" 80% // Volume Down 35 * amixer set "DVC Out" 100% // Volume Up 36 */ 37 38/dts-v1/; 39#include "r8a7790.dtsi" 40#include <dt-bindings/gpio/gpio.h> 41#include <dt-bindings/input/input.h> 42 43/ { 44 model = "Lager"; 45 compatible = "renesas,lager", "renesas,r8a7790"; 46 47 aliases { 48 serial0 = &scif0; 49 serial1 = &scifa1; 50 i2c8 = &gpioi2c1; 51 i2c9 = &gpioi2c2; 52 i2c10 = &i2cexio0; 53 i2c11 = &i2cexio1; 54 i2c12 = &i2chdmi; 55 i2c13 = &i2cpwr; 56 mmc0 = &mmcif1; 57 mmc1 = &sdhi0; 58 mmc2 = &sdhi2; 59 }; 60 61 chosen { 62 bootargs = "ignore_loglevel rw root=/dev/nfs ip=on"; 63 stdout-path = "serial0:115200n8"; 64 }; 65 66 memory@40000000 { 67 device_type = "memory"; 68 reg = <0 0x40000000 0 0x40000000>; 69 }; 70 71 memory@140000000 { 72 device_type = "memory"; 73 reg = <1 0x40000000 0 0xc0000000>; 74 }; 75 76 keyboard { 77 compatible = "gpio-keys"; 78 79 pinctrl-0 = <&keyboard_pins>; 80 pinctrl-names = "default"; 81 82 one { 83 linux,code = <KEY_1>; 84 label = "SW2-1"; 85 wakeup-source; 86 debounce-interval = <20>; 87 gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; 88 }; 89 two { 90 linux,code = <KEY_2>; 91 label = "SW2-2"; 92 wakeup-source; 93 debounce-interval = <20>; 94 gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; 95 }; 96 three { 97 linux,code = <KEY_3>; 98 label = "SW2-3"; 99 wakeup-source; 100 debounce-interval = <20>; 101 gpios = <&gpio1 26 GPIO_ACTIVE_LOW>; 102 }; 103 four { 104 linux,code = <KEY_4>; 105 label = "SW2-4"; 106 wakeup-source; 107 debounce-interval = <20>; 108 gpios = <&gpio1 28 GPIO_ACTIVE_LOW>; 109 }; 110 }; 111 112 leds { 113 compatible = "gpio-leds"; 114 led6 { 115 gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>; 116 }; 117 led7 { 118 gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>; 119 }; 120 led8 { 121 gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>; 122 }; 123 }; 124 125 fixedregulator1v8: regulator-1v8 { 126 compatible = "regulator-fixed"; 127 regulator-name = "fixed-1.8V"; 128 regulator-min-microvolt = <1800000>; 129 regulator-max-microvolt = <1800000>; 130 regulator-boot-on; 131 regulator-always-on; 132 }; 133 134 fixedregulator3v3: regulator-3v3 { 135 compatible = "regulator-fixed"; 136 regulator-name = "fixed-3.3V"; 137 regulator-min-microvolt = <3300000>; 138 regulator-max-microvolt = <3300000>; 139 regulator-boot-on; 140 regulator-always-on; 141 }; 142 143 vcc_sdhi0: regulator-vcc-sdhi0 { 144 compatible = "regulator-fixed"; 145 146 regulator-name = "SDHI0 Vcc"; 147 regulator-min-microvolt = <3300000>; 148 regulator-max-microvolt = <3300000>; 149 150 gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>; 151 enable-active-high; 152 }; 153 154 vccq_sdhi0: regulator-vccq-sdhi0 { 155 compatible = "regulator-gpio"; 156 157 regulator-name = "SDHI0 VccQ"; 158 regulator-min-microvolt = <1800000>; 159 regulator-max-microvolt = <3300000>; 160 161 gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; 162 gpios-states = <1>; 163 states = <3300000 1>, <1800000 0>; 164 }; 165 166 vcc_sdhi2: regulator-vcc-sdhi2 { 167 compatible = "regulator-fixed"; 168 169 regulator-name = "SDHI2 Vcc"; 170 regulator-min-microvolt = <3300000>; 171 regulator-max-microvolt = <3300000>; 172 173 gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>; 174 enable-active-high; 175 }; 176 177 vccq_sdhi2: regulator-vccq-sdhi2 { 178 compatible = "regulator-gpio"; 179 180 regulator-name = "SDHI2 VccQ"; 181 regulator-min-microvolt = <1800000>; 182 regulator-max-microvolt = <3300000>; 183 184 gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>; 185 gpios-states = <1>; 186 states = <3300000 1>, <1800000 0>; 187 }; 188 189 audio_clock: audio_clock { 190 compatible = "fixed-clock"; 191 #clock-cells = <0>; 192 clock-frequency = <11289600>; 193 }; 194 195 rsnd_ak4643: sound { 196 compatible = "simple-audio-card"; 197 198 simple-audio-card,format = "left_j"; 199 simple-audio-card,bitclock-master = <&sndcodec>; 200 simple-audio-card,frame-master = <&sndcodec>; 201 202 sndcpu: simple-audio-card,cpu { 203 sound-dai = <&rcar_sound>; 204 }; 205 206 sndcodec: simple-audio-card,codec { 207 sound-dai = <&ak4643>; 208 clocks = <&audio_clock>; 209 }; 210 }; 211 212 vga-encoder { 213 compatible = "adi,adv7123"; 214 215 ports { 216 #address-cells = <1>; 217 #size-cells = <0>; 218 219 port@0 { 220 reg = <0>; 221 adv7123_in: endpoint { 222 remote-endpoint = <&du_out_rgb>; 223 }; 224 }; 225 port@1 { 226 reg = <1>; 227 adv7123_out: endpoint { 228 remote-endpoint = <&vga_in>; 229 }; 230 }; 231 }; 232 }; 233 234 vga { 235 compatible = "vga-connector"; 236 237 port { 238 vga_in: endpoint { 239 remote-endpoint = <&adv7123_out>; 240 }; 241 }; 242 }; 243 244 hdmi-in { 245 compatible = "hdmi-connector"; 246 type = "a"; 247 248 port { 249 hdmi_con_in: endpoint { 250 remote-endpoint = <&adv7612_in>; 251 }; 252 }; 253 }; 254 255 cec_clock: cec-clock { 256 compatible = "fixed-clock"; 257 #clock-cells = <0>; 258 clock-frequency = <12000000>; 259 }; 260 261 hdmi-out { 262 compatible = "hdmi-connector"; 263 type = "a"; 264 265 port { 266 hdmi_con_out: endpoint { 267 remote-endpoint = <&adv7511_out>; 268 }; 269 }; 270 }; 271 272 x2_clk: x2-clock { 273 compatible = "fixed-clock"; 274 #clock-cells = <0>; 275 clock-frequency = <148500000>; 276 }; 277 278 x13_clk: x13-clock { 279 compatible = "fixed-clock"; 280 #clock-cells = <0>; 281 clock-frequency = <148500000>; 282 }; 283 284 gpioi2c1: i2c-8 { 285 #address-cells = <1>; 286 #size-cells = <0>; 287 compatible = "i2c-gpio"; 288 status = "disabled"; 289 scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 290 sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 291 i2c-gpio,delay-us = <5>; 292 }; 293 294 gpioi2c2: i2c-9 { 295 #address-cells = <1>; 296 #size-cells = <0>; 297 compatible = "i2c-gpio"; 298 status = "disabled"; 299 scl-gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 300 sda-gpios = <&gpio5 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 301 i2c-gpio,delay-us = <5>; 302 }; 303 304 /* 305 * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only. 306 * We use the I2C demuxer, so the desired IP core can be selected at runtime 307 * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0). 308 * Note: For testing the I2C slave feature, it is convenient to connect this 309 * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and 310 * instantiate the slave device at runtime according to the documentation. 311 * You can then communicate with the slave via IIC3. 312 * 313 * IIC0/I2C0 does not appear to support fallback to GPIO. 314 */ 315 i2cexio0: i2c-mux1 { 316 compatible = "i2c-demux-pinctrl"; 317 i2c-parent = <&iic0>, <&i2c0>; 318 i2c-bus-name = "i2c-exio0"; 319 #address-cells = <1>; 320 #size-cells = <0>; 321 }; 322 323 /* 324 * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA). 325 * This is similar to the arangement described for i2cexio0 (above) 326 * with a fallback to GPIO also provided. 327 */ 328 i2cexio1: i2c-mux2 { 329 compatible = "i2c-demux-pinctrl"; 330 i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>; 331 i2c-bus-name = "i2c-exio1"; 332 #address-cells = <1>; 333 #size-cells = <0>; 334 }; 335 336 /* 337 * IIC2 and I2C2 may be switched using pinmux. 338 * A fallback to GPIO is also provided. 339 */ 340 i2chdmi: i2c-mux3 { 341 compatible = "i2c-demux-pinctrl"; 342 i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>; 343 i2c-bus-name = "i2c-hdmi"; 344 #address-cells = <1>; 345 #size-cells = <0>; 346 347 ak4643: codec@12 { 348 compatible = "asahi-kasei,ak4643"; 349 #sound-dai-cells = <0>; 350 reg = <0x12>; 351 }; 352 353 composite-in@20 { 354 compatible = "adi,adv7180"; 355 reg = <0x20>; 356 357 port { 358 adv7180: endpoint { 359 bus-width = <8>; 360 remote-endpoint = <&vin1ep0>; 361 }; 362 }; 363 }; 364 365 hdmi@39 { 366 compatible = "adi,adv7511w"; 367 reg = <0x39>; 368 interrupt-parent = <&gpio1>; 369 interrupts = <15 IRQ_TYPE_LEVEL_LOW>; 370 clocks = <&cec_clock>; 371 clock-names = "cec"; 372 373 avdd-supply = <&fixedregulator1v8>; 374 dvdd-supply = <&fixedregulator1v8>; 375 pvdd-supply = <&fixedregulator1v8>; 376 dvdd-3v-supply = <&fixedregulator3v3>; 377 bgvdd-supply = <&fixedregulator1v8>; 378 379 adi,input-depth = <8>; 380 adi,input-colorspace = "rgb"; 381 adi,input-clock = "1x"; 382 383 ports { 384 #address-cells = <1>; 385 #size-cells = <0>; 386 387 port@0 { 388 reg = <0>; 389 adv7511_in: endpoint { 390 remote-endpoint = <&lvds0_out>; 391 }; 392 }; 393 394 port@1 { 395 reg = <1>; 396 adv7511_out: endpoint { 397 remote-endpoint = <&hdmi_con_out>; 398 }; 399 }; 400 }; 401 }; 402 403 hdmi-in@4c { 404 compatible = "adi,adv7612"; 405 reg = <0x4c>; 406 interrupt-parent = <&gpio1>; 407 interrupts = <20 IRQ_TYPE_LEVEL_LOW>; 408 default-input = <0>; 409 410 ports { 411 #address-cells = <1>; 412 #size-cells = <0>; 413 414 port@0 { 415 reg = <0>; 416 adv7612_in: endpoint { 417 remote-endpoint = <&hdmi_con_in>; 418 }; 419 }; 420 421 port@2 { 422 reg = <2>; 423 adv7612_out: endpoint { 424 remote-endpoint = <&vin0ep2>; 425 }; 426 }; 427 }; 428 }; 429 }; 430 431 /* 432 * IIC3 and I2C3 may be switched using pinmux. 433 * IIC3/I2C3 does not appear to support fallback to GPIO. 434 */ 435 i2cpwr: i2c-mux4 { 436 compatible = "i2c-demux-pinctrl"; 437 pinctrl-names = "default"; 438 pinctrl-0 = <&pmic_irq_pins>; 439 i2c-parent = <&iic3>, <&i2c3>; 440 i2c-bus-name = "i2c-pwr"; 441 #address-cells = <1>; 442 #size-cells = <0>; 443 444 pmic@58 { 445 compatible = "dlg,da9063"; 446 reg = <0x58>; 447 interrupt-parent = <&irqc0>; 448 interrupts = <2 IRQ_TYPE_LEVEL_LOW>; 449 interrupt-controller; 450 #interrupt-cells = <2>; 451 452 rtc { 453 compatible = "dlg,da9063-rtc"; 454 }; 455 456 watchdog { 457 compatible = "dlg,da9063-watchdog"; 458 }; 459 }; 460 461 vdd_dvfs: regulator@68 { 462 compatible = "dlg,da9210"; 463 reg = <0x68>; 464 interrupt-parent = <&irqc0>; 465 interrupts = <2 IRQ_TYPE_LEVEL_LOW>; 466 467 regulator-min-microvolt = <1000000>; 468 regulator-max-microvolt = <1000000>; 469 regulator-boot-on; 470 regulator-always-on; 471 }; 472 }; 473}; 474 475&du { 476 pinctrl-0 = <&du_pins>; 477 pinctrl-names = "default"; 478 status = "okay"; 479 480 clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>, 481 <&x13_clk>, <&x2_clk>; 482 clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1"; 483 484 ports { 485 port@0 { 486 endpoint { 487 remote-endpoint = <&adv7123_in>; 488 }; 489 }; 490 }; 491}; 492 493&lvds0 { 494 status = "okay"; 495 496 ports { 497 port@1 { 498 endpoint { 499 remote-endpoint = <&adv7511_in>; 500 }; 501 }; 502 }; 503}; 504 505&lvds1 { 506 ports { 507 port@1 { 508 lvds_connector: endpoint { 509 }; 510 }; 511 }; 512}; 513 514&extal_clk { 515 clock-frequency = <20000000>; 516}; 517 518&pfc { 519 pinctrl-0 = <&scif_clk_pins>; 520 pinctrl-names = "default"; 521 522 du_pins: du { 523 groups = "du_rgb666", "du_sync_1", "du_clk_out_0"; 524 function = "du"; 525 }; 526 527 scif0_pins: scif0 { 528 groups = "scif0_data"; 529 function = "scif0"; 530 }; 531 532 scif_clk_pins: scif_clk { 533 groups = "scif_clk"; 534 function = "scif_clk"; 535 }; 536 537 ether_pins: ether { 538 groups = "eth_link", "eth_mdio", "eth_rmii"; 539 function = "eth"; 540 }; 541 542 phy1_pins: phy1 { 543 groups = "intc_irq0"; 544 function = "intc"; 545 }; 546 547 scifa1_pins: scifa1 { 548 groups = "scifa1_data"; 549 function = "scifa1"; 550 }; 551 552 sdhi0_pins: sd0 { 553 groups = "sdhi0_data4", "sdhi0_ctrl"; 554 function = "sdhi0"; 555 power-source = <3300>; 556 }; 557 558 sdhi0_pins_uhs: sd0_uhs { 559 groups = "sdhi0_data4", "sdhi0_ctrl"; 560 function = "sdhi0"; 561 power-source = <1800>; 562 }; 563 564 sdhi2_pins: sd2 { 565 groups = "sdhi2_data4", "sdhi2_ctrl"; 566 function = "sdhi2"; 567 power-source = <3300>; 568 }; 569 570 sdhi2_pins_uhs: sd2_uhs { 571 groups = "sdhi2_data4", "sdhi2_ctrl"; 572 function = "sdhi2"; 573 power-source = <1800>; 574 }; 575 576 mmc1_pins: mmc1 { 577 groups = "mmc1_data8", "mmc1_ctrl"; 578 function = "mmc1"; 579 }; 580 581 qspi_pins: qspi { 582 groups = "qspi_ctrl", "qspi_data4"; 583 function = "qspi"; 584 }; 585 586 msiof1_pins: msiof1 { 587 groups = "msiof1_clk", "msiof1_sync", "msiof1_rx", 588 "msiof1_tx"; 589 function = "msiof1"; 590 }; 591 592 i2c0_pins: i2c0 { 593 groups = "i2c0"; 594 function = "i2c0"; 595 }; 596 597 iic0_pins: iic0 { 598 groups = "iic0"; 599 function = "iic0"; 600 }; 601 602 i2c1_pins: i2c1 { 603 groups = "i2c1"; 604 function = "i2c1"; 605 }; 606 607 iic1_pins: iic1 { 608 groups = "iic1"; 609 function = "iic1"; 610 }; 611 612 i2c2_pins: i2c2 { 613 groups = "i2c2"; 614 function = "i2c2"; 615 }; 616 617 iic2_pins: iic2 { 618 groups = "iic2"; 619 function = "iic2"; 620 }; 621 622 i2c3_pins: i2c3 { 623 groups = "i2c3"; 624 function = "i2c3"; 625 }; 626 627 iic3_pins: iic3 { 628 groups = "iic3"; 629 function = "iic3"; 630 }; 631 632 pmic_irq_pins: pmicirq { 633 groups = "intc_irq2"; 634 function = "intc"; 635 }; 636 637 hsusb_pins: hsusb { 638 groups = "usb0_ovc_vbus"; 639 function = "usb0"; 640 }; 641 642 usb0_pins: usb0 { 643 groups = "usb0"; 644 function = "usb0"; 645 }; 646 647 usb1_pins: usb1 { 648 groups = "usb1"; 649 function = "usb1"; 650 }; 651 652 usb2_pins: usb2 { 653 groups = "usb2"; 654 function = "usb2"; 655 }; 656 657 vin0_pins: vin0 { 658 groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk"; 659 function = "vin0"; 660 }; 661 662 vin1_pins: vin1 { 663 groups = "vin1_data8", "vin1_clk"; 664 function = "vin1"; 665 }; 666 667 sound_pins: sound { 668 groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data"; 669 function = "ssi"; 670 }; 671 672 sound_clk_pins: sound_clk { 673 groups = "audio_clk_a"; 674 function = "audio_clk"; 675 }; 676 677 keyboard_pins: keyboard { 678 pins = "GP_1_14", "GP_1_24", "GP_1_26", "GP_1_28"; 679 bias-pull-up; 680 }; 681}; 682 683ðer { 684 pinctrl-0 = <ðer_pins>, <&phy1_pins>; 685 pinctrl-names = "default"; 686 687 phy-handle = <&phy1>; 688 renesas,ether-link-active-low; 689 status = "okay"; 690 691 phy1: ethernet-phy@1 { 692 compatible = "ethernet-phy-id0022.1537", 693 "ethernet-phy-ieee802.3-c22"; 694 reg = <1>; 695 interrupt-parent = <&irqc0>; 696 interrupts = <0 IRQ_TYPE_LEVEL_LOW>; 697 micrel,led-mode = <1>; 698 reset-gpios = <&gpio5 31 GPIO_ACTIVE_LOW>; 699 }; 700}; 701 702&cmt0 { 703 status = "okay"; 704}; 705 706&mmcif1 { 707 pinctrl-0 = <&mmc1_pins>; 708 pinctrl-names = "default"; 709 710 vmmc-supply = <&fixedregulator3v3>; 711 bus-width = <8>; 712 non-removable; 713 status = "okay"; 714}; 715 716&sata1 { 717 status = "okay"; 718}; 719 720&qspi { 721 pinctrl-0 = <&qspi_pins>; 722 pinctrl-names = "default"; 723 724 status = "okay"; 725 726 flash: flash@0 { 727 compatible = "spansion,s25fl512s", "jedec,spi-nor"; 728 reg = <0>; 729 spi-max-frequency = <30000000>; 730 spi-tx-bus-width = <4>; 731 spi-rx-bus-width = <4>; 732 spi-cpha; 733 spi-cpol; 734 m25p,fast-read; 735 736 partitions { 737 compatible = "fixed-partitions"; 738 #address-cells = <1>; 739 #size-cells = <1>; 740 741 partition@0 { 742 label = "loader"; 743 reg = <0x00000000 0x00040000>; 744 read-only; 745 }; 746 partition@40000 { 747 label = "user"; 748 reg = <0x00040000 0x00400000>; 749 read-only; 750 }; 751 partition@440000 { 752 label = "flash"; 753 reg = <0x00440000 0x03bc0000>; 754 }; 755 }; 756 }; 757}; 758 759&scif0 { 760 pinctrl-0 = <&scif0_pins>; 761 pinctrl-names = "default"; 762 763 status = "okay"; 764}; 765 766&scifa1 { 767 pinctrl-0 = <&scifa1_pins>; 768 pinctrl-names = "default"; 769 770 status = "okay"; 771}; 772 773&scif_clk { 774 clock-frequency = <14745600>; 775}; 776 777&msiof1 { 778 pinctrl-0 = <&msiof1_pins>; 779 pinctrl-names = "default"; 780 781 status = "okay"; 782 783 pmic: pmic@0 { 784 compatible = "renesas,r2a11302ft"; 785 reg = <0>; 786 spi-max-frequency = <6000000>; 787 spi-cpol; 788 spi-cpha; 789 }; 790}; 791 792&sdhi0 { 793 pinctrl-0 = <&sdhi0_pins>; 794 pinctrl-1 = <&sdhi0_pins_uhs>; 795 pinctrl-names = "default", "state_uhs"; 796 797 vmmc-supply = <&vcc_sdhi0>; 798 vqmmc-supply = <&vccq_sdhi0>; 799 cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; 800 sd-uhs-sdr50; 801 sd-uhs-sdr104; 802 status = "okay"; 803}; 804 805&sdhi2 { 806 pinctrl-0 = <&sdhi2_pins>; 807 pinctrl-1 = <&sdhi2_pins_uhs>; 808 pinctrl-names = "default", "state_uhs"; 809 810 vmmc-supply = <&vcc_sdhi2>; 811 vqmmc-supply = <&vccq_sdhi2>; 812 cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>; 813 sd-uhs-sdr50; 814 status = "okay"; 815}; 816 817&cpu0 { 818 cpu0-supply = <&vdd_dvfs>; 819}; 820 821&i2c0 { 822 pinctrl-0 = <&i2c0_pins>; 823 pinctrl-names = "i2c-exio0"; 824}; 825 826&iic0 { 827 pinctrl-0 = <&iic0_pins>; 828 pinctrl-names = "i2c-exio0"; 829}; 830 831&i2c1 { 832 pinctrl-0 = <&i2c1_pins>; 833 pinctrl-names = "i2c-exio1"; 834}; 835 836&iic1 { 837 pinctrl-0 = <&iic1_pins>; 838 pinctrl-names = "i2c-exio1"; 839}; 840 841&i2c2 { 842 pinctrl-0 = <&i2c2_pins>; 843 pinctrl-names = "i2c-hdmi"; 844 845 clock-frequency = <100000>; 846}; 847 848&iic2 { 849 pinctrl-0 = <&iic2_pins>; 850 pinctrl-names = "i2c-hdmi"; 851 852 clock-frequency = <100000>; 853}; 854 855&i2c3 { 856 pinctrl-0 = <&i2c3_pins>; 857 pinctrl-names = "i2c-pwr"; 858}; 859 860&iic3 { 861 pinctrl-0 = <&iic3_pins>; 862 pinctrl-names = "i2c-pwr"; 863}; 864 865&pci0 { 866 status = "okay"; 867 pinctrl-0 = <&usb0_pins>; 868 pinctrl-names = "default"; 869}; 870 871&pci1 { 872 status = "okay"; 873 pinctrl-0 = <&usb1_pins>; 874 pinctrl-names = "default"; 875}; 876 877&xhci { 878 status = "okay"; 879 pinctrl-0 = <&usb2_pins>; 880 pinctrl-names = "default"; 881}; 882 883&pci2 { 884 status = "okay"; 885 pinctrl-0 = <&usb2_pins>; 886 pinctrl-names = "default"; 887}; 888 889&hsusb { 890 status = "okay"; 891 pinctrl-0 = <&hsusb_pins>; 892 pinctrl-names = "default"; 893 renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>; 894}; 895 896&usbphy { 897 status = "okay"; 898}; 899 900/* HDMI video input */ 901&vin0 { 902 pinctrl-0 = <&vin0_pins>; 903 pinctrl-names = "default"; 904 905 status = "okay"; 906 907 port { 908 vin0ep2: endpoint { 909 remote-endpoint = <&adv7612_out>; 910 bus-width = <24>; 911 hsync-active = <0>; 912 vsync-active = <0>; 913 pclk-sample = <1>; 914 data-active = <1>; 915 }; 916 }; 917}; 918 919/* composite video input */ 920&vin1 { 921 pinctrl-0 = <&vin1_pins>; 922 pinctrl-names = "default"; 923 924 status = "okay"; 925 926 port { 927 vin1ep0: endpoint { 928 remote-endpoint = <&adv7180>; 929 bus-width = <8>; 930 }; 931 }; 932}; 933 934&rcar_sound { 935 pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; 936 pinctrl-names = "default"; 937 938 /* Single DAI */ 939 #sound-dai-cells = <0>; 940 941 status = "okay"; 942 943 rcar_sound,dai { 944 dai0 { 945 playback = <&ssi0>, <&src2>, <&dvc0>; 946 capture = <&ssi1>, <&src3>, <&dvc1>; 947 }; 948 }; 949}; 950 951&rwdt { 952 timeout-sec = <60>; 953 status = "okay"; 954}; 955 956&ssi1 { 957 shared-pin; 958}; 959