1// SPDX-License-Identifier: GPL-2.0 2#include "qcom-msm8974pro.dtsi" 3#include "qcom-pma8084.dtsi" 4#include <dt-bindings/input/input.h> 5#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> 6#include <dt-bindings/leds/common.h> 7 8/ { 9 model = "Samsung Galaxy S5"; 10 compatible = "samsung,klte", "qcom,msm8974pro", "qcom,msm8974"; 11 chassis-type = "handset"; 12 13 aliases { 14 serial0 = &blsp1_uart1; 15 mmc0 = &sdhc_1; /* SDC1 eMMC slot */ 16 mmc1 = &sdhc_3; /* SDC2 SD card slot */ 17 }; 18 19 chosen { 20 stdout-path = "serial0:115200n8"; 21 }; 22 23 gpio-keys { 24 compatible = "gpio-keys"; 25 26 pinctrl-names = "default"; 27 pinctrl-0 = <&gpio_keys_pin_a>; 28 29 key-volume-down { 30 label = "volume_down"; 31 gpios = <&pma8084_gpios 2 GPIO_ACTIVE_LOW>; 32 linux,input-type = <1>; 33 linux,code = <KEY_VOLUMEDOWN>; 34 debounce-interval = <15>; 35 }; 36 37 key-home { 38 label = "home_key"; 39 gpios = <&pma8084_gpios 3 GPIO_ACTIVE_LOW>; 40 linux,input-type = <1>; 41 linux,code = <KEY_HOMEPAGE>; 42 wakeup-source; 43 debounce-interval = <15>; 44 }; 45 46 key-volume-up { 47 label = "volume_up"; 48 gpios = <&pma8084_gpios 5 GPIO_ACTIVE_LOW>; 49 linux,input-type = <1>; 50 linux,code = <KEY_VOLUMEUP>; 51 debounce-interval = <15>; 52 }; 53 }; 54 55 i2c-gpio-touchkey { 56 compatible = "i2c-gpio"; 57 #address-cells = <1>; 58 #size-cells = <0>; 59 sda-gpios = <&tlmm 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 60 scl-gpios = <&tlmm 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 61 pinctrl-names = "default"; 62 pinctrl-0 = <&i2c_touchkey_pins>; 63 64 touchkey@20 { 65 compatible = "cypress,tm2-touchkey"; 66 reg = <0x20>; 67 68 interrupt-parent = <&pma8084_gpios>; 69 interrupts = <6 IRQ_TYPE_EDGE_FALLING>; 70 pinctrl-names = "default"; 71 pinctrl-0 = <&touchkey_pin>; 72 73 vcc-supply = <&max77826_ldo15>; 74 vdd-supply = <&pma8084_l19>; 75 76 linux,keycodes = <KEY_APPSELECT KEY_BACK>; 77 }; 78 }; 79 80 i2c-gpio-led { 81 compatible = "i2c-gpio"; 82 #address-cells = <1>; 83 #size-cells = <0>; 84 scl-gpios = <&tlmm 121 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 85 sda-gpios = <&tlmm 120 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 86 pinctrl-names = "default"; 87 pinctrl-0 = <&i2c_led_gpioex_pins>; 88 89 i2c-gpio,delay-us = <2>; 90 91 gpio_expander: gpio@20 { 92 compatible = "nxp,pcal6416"; 93 reg = <0x20>; 94 95 gpio-controller; 96 #gpio-cells = <2>; 97 98 vcc-supply = <&pma8084_s4>; 99 100 pinctrl-names = "default"; 101 pinctrl-0 = <&gpioex_pin>; 102 103 reset-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>; 104 }; 105 106 led-controller@30 { 107 compatible = "panasonic,an30259a"; 108 reg = <0x30>; 109 110 #address-cells = <1>; 111 #size-cells = <0>; 112 113 led@1 { 114 reg = <1>; 115 function = LED_FUNCTION_STATUS; 116 color = <LED_COLOR_ID_RED>; 117 }; 118 119 led@2 { 120 reg = <2>; 121 function = LED_FUNCTION_STATUS; 122 color = <LED_COLOR_ID_GREEN>; 123 }; 124 125 led@3 { 126 reg = <3>; 127 function = LED_FUNCTION_STATUS; 128 color = <LED_COLOR_ID_BLUE>; 129 }; 130 }; 131 }; 132 133 vreg_wlan: wlan-regulator { 134 compatible = "regulator-fixed"; 135 136 regulator-name = "wl-reg"; 137 regulator-min-microvolt = <3300000>; 138 regulator-max-microvolt = <3300000>; 139 140 gpio = <&gpio_expander 8 GPIO_ACTIVE_HIGH>; 141 enable-active-high; 142 }; 143 144 vreg_panel: panel-regulator { 145 compatible = "regulator-fixed"; 146 147 pinctrl-names = "default"; 148 pinctrl-0 = <&panel_en_pin>; 149 150 regulator-name = "panel-vddr-reg"; 151 regulator-min-microvolt = <1500000>; 152 regulator-max-microvolt = <1500000>; 153 154 gpio = <&pma8084_gpios 14 GPIO_ACTIVE_HIGH>; 155 enable-active-high; 156 }; 157 158 /delete-node/ vreg-boost; 159}; 160 161&blsp1_i2c2 { 162 status = "okay"; 163 164 touchscreen@20 { 165 compatible = "syna,rmi4-i2c"; 166 reg = <0x20>; 167 168 interrupt-parent = <&pma8084_gpios>; 169 interrupts = <8 IRQ_TYPE_EDGE_FALLING>; 170 171 vdd-supply = <&max77826_ldo13>; 172 vio-supply = <&pma8084_lvs2>; 173 174 pinctrl-names = "default"; 175 pinctrl-0 = <&touch_pin>; 176 177 syna,startup-delay-ms = <100>; 178 179 #address-cells = <1>; 180 #size-cells = <0>; 181 182 rmi4-f01@1 { 183 reg = <0x1>; 184 syna,nosleep-mode = <1>; 185 }; 186 187 rmi4-f12@12 { 188 reg = <0x12>; 189 syna,sensor-type = <1>; 190 }; 191 }; 192}; 193 194&blsp1_i2c6 { 195 status = "okay"; 196 197 pmic@60 { 198 reg = <0x60>; 199 compatible = "maxim,max77826"; 200 201 regulators { 202 max77826_ldo1: LDO1 { 203 regulator-min-microvolt = <1200000>; 204 regulator-max-microvolt = <1200000>; 205 }; 206 207 max77826_ldo2: LDO2 { 208 regulator-min-microvolt = <1000000>; 209 regulator-max-microvolt = <1000000>; 210 }; 211 212 max77826_ldo3: LDO3 { 213 regulator-min-microvolt = <1200000>; 214 regulator-max-microvolt = <1200000>; 215 }; 216 217 max77826_ldo4: LDO4 { 218 regulator-min-microvolt = <1800000>; 219 regulator-max-microvolt = <1800000>; 220 }; 221 222 max77826_ldo5: LDO5 { 223 regulator-min-microvolt = <1800000>; 224 regulator-max-microvolt = <1800000>; 225 }; 226 227 max77826_ldo6: LDO6 { 228 regulator-min-microvolt = <1800000>; 229 regulator-max-microvolt = <3300000>; 230 }; 231 232 max77826_ldo7: LDO7 { 233 regulator-min-microvolt = <1800000>; 234 regulator-max-microvolt = <1800000>; 235 }; 236 237 max77826_ldo8: LDO8 { 238 regulator-min-microvolt = <1800000>; 239 regulator-max-microvolt = <3300000>; 240 }; 241 242 max77826_ldo9: LDO9 { 243 regulator-min-microvolt = <1800000>; 244 regulator-max-microvolt = <1800000>; 245 }; 246 247 max77826_ldo10: LDO10 { 248 regulator-min-microvolt = <2800000>; 249 regulator-max-microvolt = <2950000>; 250 }; 251 252 max77826_ldo11: LDO11 { 253 regulator-min-microvolt = <2700000>; 254 regulator-max-microvolt = <2950000>; 255 }; 256 257 max77826_ldo12: LDO12 { 258 regulator-min-microvolt = <2500000>; 259 regulator-max-microvolt = <3300000>; 260 }; 261 262 max77826_ldo13: LDO13 { 263 regulator-min-microvolt = <3300000>; 264 regulator-max-microvolt = <3300000>; 265 }; 266 267 max77826_ldo14: LDO14 { 268 regulator-min-microvolt = <3300000>; 269 regulator-max-microvolt = <3300000>; 270 }; 271 272 max77826_ldo15: LDO15 { 273 regulator-min-microvolt = <1800000>; 274 regulator-max-microvolt = <1800000>; 275 }; 276 277 max77826_buck: BUCK { 278 regulator-min-microvolt = <1225000>; 279 regulator-max-microvolt = <1225000>; 280 }; 281 282 max77826_buckboost: BUCKBOOST { 283 regulator-min-microvolt = <3400000>; 284 regulator-max-microvolt = <3400000>; 285 }; 286 }; 287 }; 288}; 289 290&blsp1_uart2 { 291 status = "okay"; 292}; 293 294&blsp2_i2c6 { 295 status = "okay"; 296 297 fuelgauge@36 { 298 compatible = "maxim,max17048"; 299 reg = <0x36>; 300 301 maxim,double-soc; 302 maxim,rcomp = /bits/ 8 <0x56>; 303 304 interrupt-parent = <&pma8084_gpios>; 305 interrupts = <21 IRQ_TYPE_LEVEL_LOW>; 306 307 pinctrl-names = "default"; 308 pinctrl-0 = <&fuelgauge_pin>; 309 }; 310}; 311 312&blsp2_uart2 { 313 status = "okay"; 314 315 pinctrl-names = "default", "sleep"; 316 pinctrl-0 = <&blsp2_uart2_pins_active>; 317 pinctrl-1 = <&blsp2_uart2_pins_sleep>; 318 319 bluetooth { 320 compatible = "brcm,bcm43540-bt"; 321 max-speed = <3000000>; 322 pinctrl-names = "default"; 323 pinctrl-0 = <&bt_pins>; 324 device-wakeup-gpios = <&tlmm 91 GPIO_ACTIVE_HIGH>; 325 shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>; 326 interrupt-parent = <&tlmm>; 327 interrupts = <75 IRQ_TYPE_LEVEL_HIGH>; 328 interrupt-names = "host-wakeup"; 329 }; 330}; 331 332&gpu { 333 status = "okay"; 334}; 335 336&mdss { 337 status = "okay"; 338}; 339 340&mdss_dsi0 { 341 status = "okay"; 342 343 vdda-supply = <&pma8084_l2>; 344 vdd-supply = <&pma8084_l22>; 345 vddio-supply = <&pma8084_l12>; 346 347 panel: panel@0 { 348 reg = <0>; 349 compatible = "samsung,s6e3fa2"; 350 351 pinctrl-names = "default"; 352 pinctrl-0 = <&panel_te_pin &panel_rst_pin>; 353 354 iovdd-supply = <&pma8084_lvs4>; 355 vddr-supply = <&vreg_panel>; 356 357 reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>; 358 te-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; 359 360 port { 361 panel_in: endpoint { 362 remote-endpoint = <&mdss_dsi0_out>; 363 }; 364 }; 365 }; 366}; 367 368&mdss_dsi0_out { 369 remote-endpoint = <&panel_in>; 370 data-lanes = <0 1 2 3>; 371}; 372 373&mdss_dsi0_phy { 374 status = "okay"; 375 376 vddio-supply = <&pma8084_l12>; 377}; 378 379&pma8084_gpios { 380 gpio_keys_pin_a: gpio-keys-active-state { 381 pins = "gpio2", "gpio3", "gpio5"; 382 function = "normal"; 383 384 bias-pull-up; 385 power-source = <PMA8084_GPIO_S4>; 386 }; 387 388 touchkey_pin: touchkey-int-state { 389 pins = "gpio6"; 390 function = "normal"; 391 bias-disable; 392 input-enable; 393 power-source = <PMA8084_GPIO_S4>; 394 }; 395 396 touch_pin: touchscreen-int-state { 397 pins = "gpio8"; 398 function = "normal"; 399 bias-disable; 400 input-enable; 401 power-source = <PMA8084_GPIO_S4>; 402 }; 403 404 panel_en_pin: panel-en-state { 405 pins = "gpio14"; 406 function = "normal"; 407 bias-pull-up; 408 power-source = <PMA8084_GPIO_S4>; 409 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; 410 }; 411 412 wlan_sleep_clk_pin: wlan-sleep-clk-state { 413 pins = "gpio16"; 414 function = "func2"; 415 416 output-high; 417 power-source = <PMA8084_GPIO_S4>; 418 qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; 419 }; 420 421 panel_rst_pin: panel-rst-state { 422 pins = "gpio17"; 423 function = "normal"; 424 bias-disable; 425 power-source = <PMA8084_GPIO_S4>; 426 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; 427 }; 428 429 fuelgauge_pin: fuelgauge-int-state { 430 pins = "gpio21"; 431 function = "normal"; 432 bias-disable; 433 input-enable; 434 power-source = <PMA8084_GPIO_S4>; 435 }; 436}; 437 438&remoteproc_adsp { 439 status = "okay"; 440 cx-supply = <&pma8084_s2>; 441}; 442 443&remoteproc_mss { 444 status = "okay"; 445 cx-supply = <&pma8084_s2>; 446 mss-supply = <&pma8084_s6>; 447 mx-supply = <&pma8084_s1>; 448 pll-supply = <&pma8084_l12>; 449}; 450 451&rpm_requests { 452 regulators-0 { 453 compatible = "qcom,rpm-pma8084-regulators"; 454 455 pma8084_s1: s1 { 456 regulator-min-microvolt = <675000>; 457 regulator-max-microvolt = <1050000>; 458 regulator-always-on; 459 }; 460 461 pma8084_s2: s2 { 462 regulator-min-microvolt = <500000>; 463 regulator-max-microvolt = <1050000>; 464 }; 465 466 pma8084_s3: s3 { 467 regulator-min-microvolt = <1300000>; 468 regulator-max-microvolt = <1300000>; 469 }; 470 471 pma8084_s4: s4 { 472 regulator-min-microvolt = <1800000>; 473 regulator-max-microvolt = <1800000>; 474 }; 475 476 pma8084_s5: s5 { 477 regulator-min-microvolt = <2150000>; 478 regulator-max-microvolt = <2150000>; 479 }; 480 481 pma8084_s6: s6 { 482 regulator-min-microvolt = <1050000>; 483 regulator-max-microvolt = <1050000>; 484 }; 485 486 pma8084_l1: l1 { 487 regulator-min-microvolt = <1225000>; 488 regulator-max-microvolt = <1225000>; 489 }; 490 491 pma8084_l2: l2 { 492 regulator-min-microvolt = <1200000>; 493 regulator-max-microvolt = <1200000>; 494 }; 495 496 pma8084_l3: l3 { 497 regulator-min-microvolt = <1050000>; 498 regulator-max-microvolt = <1200000>; 499 }; 500 501 pma8084_l4: l4 { 502 regulator-min-microvolt = <1200000>; 503 regulator-max-microvolt = <1225000>; 504 }; 505 506 pma8084_l5: l5 { 507 regulator-min-microvolt = <1800000>; 508 regulator-max-microvolt = <1800000>; 509 }; 510 511 pma8084_l6: l6 { 512 regulator-min-microvolt = <1800000>; 513 regulator-max-microvolt = <1800000>; 514 }; 515 516 pma8084_l7: l7 { 517 regulator-min-microvolt = <1800000>; 518 regulator-max-microvolt = <1800000>; 519 }; 520 521 pma8084_l8: l8 { 522 regulator-min-microvolt = <1800000>; 523 regulator-max-microvolt = <1800000>; 524 }; 525 526 pma8084_l9: l9 { 527 regulator-min-microvolt = <1800000>; 528 regulator-max-microvolt = <2950000>; 529 }; 530 531 pma8084_l10: l10 { 532 regulator-min-microvolt = <1800000>; 533 regulator-max-microvolt = <2950000>; 534 }; 535 536 pma8084_l11: l11 { 537 regulator-min-microvolt = <1300000>; 538 regulator-max-microvolt = <1300000>; 539 }; 540 541 pma8084_l12: l12 { 542 regulator-min-microvolt = <1800000>; 543 regulator-max-microvolt = <1800000>; 544 regulator-always-on; 545 }; 546 547 pma8084_l13: l13 { 548 regulator-min-microvolt = <1800000>; 549 regulator-max-microvolt = <2950000>; 550 }; 551 552 pma8084_l14: l14 { 553 regulator-min-microvolt = <1800000>; 554 regulator-max-microvolt = <1800000>; 555 }; 556 557 pma8084_l15: l15 { 558 regulator-min-microvolt = <2050000>; 559 regulator-max-microvolt = <2050000>; 560 }; 561 562 pma8084_l16: l16 { 563 regulator-min-microvolt = <2700000>; 564 regulator-max-microvolt = <2700000>; 565 }; 566 567 pma8084_l17: l17 { 568 regulator-min-microvolt = <2850000>; 569 regulator-max-microvolt = <2850000>; 570 }; 571 572 pma8084_l18: l18 { 573 regulator-min-microvolt = <2850000>; 574 regulator-max-microvolt = <2850000>; 575 }; 576 577 pma8084_l19: l19 { 578 regulator-min-microvolt = <3300000>; 579 regulator-max-microvolt = <3300000>; 580 }; 581 582 pma8084_l20: l20 { 583 regulator-min-microvolt = <2950000>; 584 regulator-max-microvolt = <2950000>; 585 regulator-system-load = <200000>; 586 regulator-allow-set-load; 587 }; 588 589 pma8084_l21: l21 { 590 regulator-min-microvolt = <2950000>; 591 regulator-max-microvolt = <2950000>; 592 regulator-system-load = <200000>; 593 regulator-allow-set-load; 594 }; 595 596 pma8084_l22: l22 { 597 regulator-min-microvolt = <3000000>; 598 regulator-max-microvolt = <3300000>; 599 }; 600 601 pma8084_l23: l23 { 602 regulator-min-microvolt = <3000000>; 603 regulator-max-microvolt = <3000000>; 604 }; 605 606 pma8084_l24: l24 { 607 regulator-min-microvolt = <3075000>; 608 regulator-max-microvolt = <3075000>; 609 }; 610 611 pma8084_l25: l25 { 612 regulator-min-microvolt = <2100000>; 613 regulator-max-microvolt = <2100000>; 614 }; 615 616 pma8084_l26: l26 { 617 regulator-min-microvolt = <1800000>; 618 regulator-max-microvolt = <2050000>; 619 }; 620 621 pma8084_l27: l27 { 622 regulator-min-microvolt = <1000000>; 623 regulator-max-microvolt = <1225000>; 624 }; 625 626 pma8084_lvs1: lvs1 {}; 627 pma8084_lvs2: lvs2 {}; 628 pma8084_lvs3: lvs3 {}; 629 pma8084_lvs4: lvs4 {}; 630 631 pma8084_5vs1: 5vs1 {}; 632 }; 633}; 634 635&sdhc_1 { 636 status = "okay"; 637 638 vmmc-supply = <&pma8084_l20>; 639 vqmmc-supply = <&pma8084_s4>; 640 641 pinctrl-names = "default", "sleep"; 642 pinctrl-0 = <&sdc1_on>; 643 pinctrl-1 = <&sdc1_off>; 644}; 645 646&sdhc_2 { 647 status = "okay"; 648 max-frequency = <100000000>; 649 vmmc-supply = <&vreg_wlan>; 650 vqmmc-supply = <&pma8084_s4>; 651 non-removable; 652 653 pinctrl-names = "default", "sleep"; 654 pinctrl-0 = <&sdc2_on>; 655 pinctrl-1 = <&sdc2_off>; 656 657 wifi@1 { 658 reg = <1>; 659 compatible = "brcm,bcm4329-fmac"; 660 661 interrupt-parent = <&tlmm>; 662 interrupts = <92 IRQ_TYPE_LEVEL_HIGH>; 663 interrupt-names = "host-wake"; 664 665 pinctrl-names = "default"; 666 pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>; 667 }; 668}; 669 670&sdhc_3 { 671 status = "okay"; 672 max-frequency = <100000000>; 673 vmmc-supply = <&pma8084_l21>; 674 vqmmc-supply = <&pma8084_l13>; 675 676 /* 677 * cd-gpio is intentionally disabled. If enabled, an SD card 678 * present during boot is not initialized correctly. Without 679 * cd-gpios the driver resorts to polling, so hotplug works. 680 */ 681 pinctrl-names = "default"; 682 pinctrl-0 = <&sdc3_on /* &sdhc3_cd_pin */>; 683 /* cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; */ 684}; 685 686&tlmm { 687 /* This seems suspicious, but somebody with this device should look into it. */ 688 blsp2_uart2_pins_active: blsp2-uart2-pins-active-state { 689 pins = "gpio45", "gpio46", "gpio47", "gpio48"; 690 function = "blsp_uart8"; 691 drive-strength = <8>; 692 bias-disable; 693 }; 694 695 blsp2_uart2_pins_sleep: blsp2-uart2-pins-sleep-state { 696 pins = "gpio45", "gpio46", "gpio47", "gpio48"; 697 function = "gpio"; 698 drive-strength = <2>; 699 bias-pull-down; 700 }; 701 702 bt_pins: bt-pins-state { 703 hostwake-pins { 704 pins = "gpio75"; 705 function = "gpio"; 706 drive-strength = <16>; 707 }; 708 709 devwake-pins { 710 pins = "gpio91"; 711 function = "gpio"; 712 drive-strength = <2>; 713 }; 714 }; 715 716 sdc1_on: sdhc1-on-state { 717 clk-pins { 718 pins = "sdc1_clk"; 719 drive-strength = <4>; 720 bias-disable; 721 }; 722 723 cmd-data-pins { 724 pins = "sdc1_cmd", "sdc1_data"; 725 drive-strength = <4>; 726 bias-pull-up; 727 }; 728 }; 729 730 sdc3_on: sdc3-on-state { 731 pins = "gpio35", "gpio36", "gpio37", "gpio38", "gpio39", "gpio40"; 732 function = "sdc3"; 733 drive-strength = <8>; 734 bias-disable; 735 }; 736 737 sdhc3_cd_pin: sdc3-cd-on-state { 738 pins = "gpio62"; 739 function = "gpio"; 740 741 drive-strength = <2>; 742 bias-disable; 743 }; 744 745 sdc2_on: sdhc2-on-state { 746 clk-pins { 747 pins = "sdc2_clk"; 748 drive-strength = <6>; 749 bias-disable; 750 }; 751 752 cmd-data-pins { 753 pins = "sdc2_cmd", "sdc2_data"; 754 drive-strength = <6>; 755 bias-pull-up; 756 }; 757 }; 758 759 i2c_touchkey_pins: i2c-touchkey-state { 760 pins = "gpio95", "gpio96"; 761 function = "gpio"; 762 bias-pull-up; 763 }; 764 765 i2c_led_gpioex_pins: i2c-led-gpioex-state { 766 pins = "gpio120", "gpio121"; 767 function = "gpio"; 768 bias-pull-down; 769 }; 770 771 gpioex_pin: gpioex-state { 772 pins = "gpio145"; 773 function = "gpio"; 774 bias-pull-up; 775 drive-strength = <2>; 776 }; 777 778 wifi_pin: wifi-state { 779 pins = "gpio92"; 780 function = "gpio"; 781 bias-pull-down; 782 }; 783 784 panel_te_pin: panel-state { 785 pins = "gpio12"; 786 function = "mdp_vsync"; 787 drive-strength = <2>; 788 bias-disable; 789 }; 790}; 791 792&usb { 793 status = "okay"; 794 795 phys = <&usb_hs1_phy>; 796 phy-select = <&tcsr 0xb000 0>; 797 798 hnp-disable; 799 srp-disable; 800 adp-disable; 801}; 802 803&usb_hs1_phy { 804 status = "okay"; 805 806 v1p8-supply = <&pma8084_l6>; 807 v3p3-supply = <&pma8084_l24>; 808 809 qcom,init-seq = /bits/ 8 <0x1 0x64>; 810}; 811