1// SPDX-License-Identifier: BSD-3-Clause 2 3/dts-v1/; 4 5#include "qcom-msm8226.dtsi" 6#include "pm8226.dtsi" 7 8/delete-node/ &smem_region; 9 10/ { 11 model = "Motorola Moto G 4G (2013)"; 12 compatible = "motorola,peregrine", "qcom,msm8926", "qcom,msm8226"; 13 chassis-type = "handset"; 14 15 aliases { 16 mmc0 = &sdhc_1; /* SDC1 eMMC slot */ 17 mmc1 = &sdhc_2; /* SDC2 SD card slot */ 18 }; 19 20 chosen { 21 #address-cells = <1>; 22 #size-cells = <1>; 23 ranges; 24 25 framebuffer0: framebuffer@3200000 { 26 compatible = "simple-framebuffer"; 27 reg = <0x03200000 0x800000>; 28 width = <720>; 29 height = <1280>; 30 stride = <(720 * 3)>; 31 format = "r8g8b8"; 32 vsp-supply = <®_lcd_pos>; 33 vsn-supply = <®_lcd_neg>; 34 vdd-supply = <&pm8226_l28>; 35 vddio-supply = <&vddio_disp_vreg>; 36 }; 37 }; 38 39 gpio-keys { 40 compatible = "gpio-keys"; 41 42 event-hall-sensor { 43 label = "Hall Effect Sensor"; 44 gpios = <&tlmm 51 GPIO_ACTIVE_LOW>; 45 linux,input-type = <EV_SW>; 46 linux,code = <SW_LID>; 47 linux,can-disable; 48 }; 49 50 key-volume-up { 51 label = "Volume Up"; 52 gpios = <&tlmm 106 GPIO_ACTIVE_LOW>; 53 linux,code = <KEY_VOLUMEUP>; 54 debounce-interval = <15>; 55 }; 56 }; 57 58 vddio_disp_vreg: regulator-vddio-disp { 59 compatible = "regulator-fixed"; 60 regulator-name = "vddio_disp"; 61 gpio = <&tlmm 34 GPIO_ACTIVE_HIGH>; 62 startup-delay-us = <300>; 63 enable-active-high; 64 regulator-boot-on; 65 vin-supply = <&pm8226_l8>; 66 pinctrl-0 = <&disp_vddio_default>; 67 pinctrl-names = "default"; 68 }; 69 70 reserved-memory { 71 #address-cells = <1>; 72 #size-cells = <1>; 73 ranges; 74 75 framebuffer@3200000 { 76 reg = <0x03200000 0x800000>; 77 no-map; 78 }; 79 80 smem_region: smem@fa00000 { 81 reg = <0x0fa00000 0x100000>; 82 no-map; 83 }; 84 }; 85}; 86 87&blsp1_i2c2 { 88 clock-frequency = <100000>; 89 status = "okay"; 90 91 magnetometer@c { 92 compatible = "asahi-kasei,ak8963"; 93 reg = <0xc>; 94 interrupts-extended = <&tlmm 38 IRQ_TYPE_EDGE_FALLING>; 95 reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; 96 vdd-supply = <&pm8226_l19>; 97 pinctrl-0 = <&mag_int_default &mag_reset_default>; 98 pinctrl-names = "default"; 99 }; 100 101 accelerometer@18 { 102 compatible = "st,lis3dh-accel"; 103 reg = <0x18>; 104 interrupts-extended = <&tlmm 1 IRQ_TYPE_EDGE_FALLING>; 105 vdd-supply = <&pm8226_l19>; 106 pinctrl-0 = <&accel_int_default>; 107 pinctrl-names = "default"; 108 st,drdy-int-pin = <1>; 109 }; 110}; 111 112&blsp1_i2c3 { 113 clock-frequency = <400000>; 114 status = "okay"; 115 116 regulator@3e { 117 compatible = "ti,tps65132"; 118 reg = <0x3e>; 119 pinctrl-0 = <®_lcd_default>; 120 pinctrl-names = "default"; 121 122 reg_lcd_pos: outp { 123 regulator-name = "outp"; 124 regulator-min-microvolt = <4000000>; 125 regulator-max-microvolt = <6000000>; 126 regulator-active-discharge = <1>; 127 regulator-boot-on; 128 enable-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>; 129 }; 130 131 reg_lcd_neg: outn { 132 regulator-name = "outn"; 133 regulator-min-microvolt = <4000000>; 134 regulator-max-microvolt = <6000000>; 135 regulator-active-discharge = <1>; 136 regulator-boot-on; 137 enable-gpios = <&tlmm 33 GPIO_ACTIVE_HIGH>; 138 }; 139 }; 140 141 sensor@48 { 142 compatible = "ti,tmp108"; 143 reg = <0x48>; 144 interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>; 145 pinctrl-0 = <&temp_alert_default>; 146 pinctrl-names = "default"; 147 #thermal-sensor-cells = <0>; 148 }; 149}; 150 151&blsp1_uart3 { 152 status = "okay"; 153}; 154 155&pm8226_resin { 156 linux,code = <KEY_VOLUMEDOWN>; 157 status = "okay"; 158}; 159 160&pm8226_vib { 161 status = "okay"; 162}; 163 164&rpm_requests { 165 regulators { 166 compatible = "qcom,rpm-pm8226-regulators"; 167 168 pm8226_s3: s3 { 169 regulator-min-microvolt = <1200000>; 170 regulator-max-microvolt = <1300000>; 171 }; 172 173 pm8226_s4: s4 { 174 regulator-min-microvolt = <1800000>; 175 regulator-max-microvolt = <2200000>; 176 }; 177 178 pm8226_s5: s5 { 179 regulator-min-microvolt = <1150000>; 180 regulator-max-microvolt = <1150000>; 181 }; 182 183 pm8226_l1: l1 { 184 regulator-min-microvolt = <1225000>; 185 regulator-max-microvolt = <1225000>; 186 }; 187 188 pm8226_l2: l2 { 189 regulator-min-microvolt = <1200000>; 190 regulator-max-microvolt = <1200000>; 191 }; 192 193 pm8226_l3: l3 { 194 regulator-min-microvolt = <750000>; 195 regulator-max-microvolt = <1337500>; 196 }; 197 198 pm8226_l4: l4 { 199 regulator-min-microvolt = <1200000>; 200 regulator-max-microvolt = <1200000>; 201 }; 202 203 pm8226_l5: l5 { 204 regulator-min-microvolt = <1200000>; 205 regulator-max-microvolt = <1200000>; 206 }; 207 208 pm8226_l6: l6 { 209 regulator-min-microvolt = <1800000>; 210 regulator-max-microvolt = <1800000>; 211 regulator-allow-set-load; 212 }; 213 214 pm8226_l7: l7 { 215 regulator-min-microvolt = <1850000>; 216 regulator-max-microvolt = <1850000>; 217 }; 218 219 pm8226_l8: l8 { 220 regulator-min-microvolt = <1800000>; 221 regulator-max-microvolt = <1800000>; 222 }; 223 224 pm8226_l9: l9 { 225 regulator-min-microvolt = <2050000>; 226 regulator-max-microvolt = <2050000>; 227 }; 228 229 pm8226_l10: l10 { 230 regulator-min-microvolt = <1800000>; 231 regulator-max-microvolt = <1800000>; 232 }; 233 234 pm8226_l12: l12 { 235 regulator-min-microvolt = <1800000>; 236 regulator-max-microvolt = <1800000>; 237 }; 238 239 pm8226_l14: l14 { 240 regulator-min-microvolt = <2750000>; 241 regulator-max-microvolt = <2750000>; 242 }; 243 244 pm8226_l15: l15 { 245 regulator-min-microvolt = <2800000>; 246 regulator-max-microvolt = <2800000>; 247 }; 248 249 pm8226_l16: l16 { 250 regulator-min-microvolt = <3000000>; 251 regulator-max-microvolt = <3350000>; 252 }; 253 254 pm8226_l17: l17 { 255 regulator-min-microvolt = <2950000>; 256 regulator-max-microvolt = <2950000>; 257 }; 258 259 pm8226_l18: l18 { 260 regulator-min-microvolt = <2950000>; 261 regulator-max-microvolt = <2950000>; 262 }; 263 264 pm8226_l19: l19 { 265 regulator-min-microvolt = <2850000>; 266 regulator-max-microvolt = <2850000>; 267 }; 268 269 pm8226_l20: l20 { 270 regulator-min-microvolt = <3075000>; 271 regulator-max-microvolt = <3075000>; 272 }; 273 274 pm8226_l21: l21 { 275 regulator-min-microvolt = <1800000>; 276 regulator-max-microvolt = <2950000>; 277 regulator-allow-set-load; 278 }; 279 280 pm8226_l22: l22 { 281 regulator-min-microvolt = <1800000>; 282 regulator-max-microvolt = <2950000>; 283 }; 284 285 pm8226_l23: l23 { 286 regulator-min-microvolt = <1800000>; 287 regulator-max-microvolt = <2950000>; 288 }; 289 290 pm8226_l24: l24 { 291 regulator-min-microvolt = <1300000>; 292 regulator-max-microvolt = <1350000>; 293 }; 294 295 pm8226_l25: l25 { 296 regulator-min-microvolt = <1775000>; 297 regulator-max-microvolt = <2125000>; 298 }; 299 300 pm8226_l26: l26 { 301 regulator-min-microvolt = <1225000>; 302 regulator-max-microvolt = <1225000>; 303 }; 304 305 pm8226_l27: l27 { 306 regulator-min-microvolt = <2050000>; 307 regulator-max-microvolt = <2050000>; 308 }; 309 310 pm8226_l28: l28 { 311 regulator-min-microvolt = <1800000>; 312 regulator-max-microvolt = <3400000>; 313 regulator-boot-on; 314 }; 315 316 pm8226_lvs1: lvs1 { 317 /* Pull-up for I2C lines */ 318 regulator-always-on; 319 }; 320 }; 321}; 322 323&sdhc_1 { 324 vmmc-supply = <&pm8226_l17>; 325 vqmmc-supply = <&pm8226_l6>; 326 327 bus-width = <8>; 328 non-removable; 329 330 status = "okay"; 331}; 332 333&sdhc_2 { 334 vmmc-supply = <&pm8226_l18>; 335 vqmmc-supply = <&pm8226_l21>; 336 337 bus-width = <4>; 338 cd-gpios = <&tlmm 115 GPIO_ACTIVE_HIGH>; 339 340 status = "okay"; 341}; 342 343&smbb { 344 qcom,fast-charge-safe-current = <2000000>; 345 qcom,fast-charge-current-limit = <1900000>; 346 qcom,fast-charge-safe-voltage = <4400000>; 347 qcom,minimum-input-voltage = <4300000>; 348 349 status = "okay"; 350}; 351 352&tlmm { 353 accel_int_default: accel-int-default-state { 354 pins = "gpio1"; 355 function = "gpio"; 356 drive-strength = <2>; 357 bias-disable; 358 output-disable; 359 }; 360 361 disp_vddio_default: disp-vddio-default-state { 362 pins = "gpio34"; 363 function = "gpio"; 364 drive-strength = <2>; 365 bias-disable; 366 output-high; 367 }; 368 369 mag_int_default: mag-int-default-state { 370 pins = "gpio38"; 371 function = "gpio"; 372 drive-strength = <2>; 373 bias-disable; 374 output-disable; 375 }; 376 377 mag_reset_default: mag-reset-default-state { 378 pins = "gpio62"; 379 function = "gpio"; 380 drive-strength = <2>; 381 bias-disable; 382 output-high; 383 }; 384 385 reg_lcd_default: reg-lcd-default-state { 386 pins = "gpio31", "gpio33"; 387 function = "gpio"; 388 drive-strength = <2>; 389 bias-disable; 390 output-high; 391 }; 392 393 temp_alert_default: temp-alert-default-state { 394 pins = "gpio13"; 395 function = "gpio"; 396 drive-strength = <2>; 397 bias-disable; 398 output-disable; 399 }; 400}; 401 402&usb { 403 extcon = <&smbb>; 404 dr_mode = "peripheral"; 405 status = "okay"; 406}; 407 408&usb_hs_phy { 409 extcon = <&smbb>; 410 v1p8-supply = <&pm8226_l10>; 411 v3p3-supply = <&pm8226_l20>; 412}; 413